Lines Matching +full:led +full:- +full:7 +full:seg
1 // SPDX-License-Identifier: (GPL-2.0 OR MIT)
4 (x530/AT-GS980MX)
9 /dts-v1/;
10 #include "armada-385.dtsi"
12 #include <dt-bindings/gpio/gpio.h>
15 model = "x530/AT-GS980MX";
19 stdout-path = "serial1:115200n8";
32 internal-regs {
34 pinctrl-names = "default";
35 pinctrl-0 = <&i2c0_pins>;
40 pinctrl-names = "default";
41 pinctrl-0 = <&uart0_pins>;
47 led-7seg {
48 compatible = "gpio-7-segment";
49 segment-gpios = <&led_7seg_gpio 0 GPIO_ACTIVE_LOW>,
65 reset-gpios = <&gpio1 23 GPIO_ACTIVE_LOW>;
66 reset-delay-us = <400000>;
74 compatible = "marvell,mvebu-devbus";
77 devbus,bus-width = <8>;
78 devbus,turn-off-ps = <60000>;
79 devbus,badr-skew-ps = <0>;
80 devbus,acc-first-ps = <124000>;
81 devbus,acc-next-ps = <248000>;
82 devbus,rd-setup-ps = <0>;
83 devbus,rd-hold-ps = <0>;
86 devbus,sync-enable = <0>;
87 devbus,wr-high-ps = <60000>;
88 devbus,wr-low-ps = <60000>;
89 devbus,ale-wr-ps = <60000>;
94 compatible = "mtd-ram";
96 bank-width = <1>;
102 i2c0_gpio_pins: i2c-gpio-pins-0 {
109 clock-frequency = <100000>;
112 pinctrl-names = "default", "gpio";
113 pinctrl-0 = <&i2c0_pins>;
114 pinctrl-1 = <&i2c0_gpio_pins>;
115 scl-gpio = <&gpio0 2 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
116 sda-gpio = <&gpio0 3 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
119 #address-cells = <1>;
120 #size-cells = <0>;
123 i2c-mux-idle-disconnect;
126 #address-cells = <1>;
127 #size-cells = <0>;
132 #address-cells = <1>;
133 #size-cells = <0>;
148 #address-cells = <1>;
149 #size-cells = <0>;
159 #address-cells = <1>;
160 #size-cells = <0>;
165 gpio-controller;
166 #gpio-cells = <2>;
178 pinctrl-names = "default";
179 pinctrl-0 = <&spi1_pins>;
183 #address-cells = <1>;
184 #size-cells = <1>;
185 compatible = "jedec,spi-nor";
187 spi-max-frequency = <54000000>;
190 compatible = "fixed-partitions";
191 #address-cells = <1>;
192 #size-cells = <1>;
195 label = "u-boot";
199 label = "u-boot-env";
218 label = "pxa3xx_nand-0";
219 nand-rb = <0>;
220 nand-on-flash-bbt;
221 nand-ecc-strength = <4>;
222 nand-ecc-step-size = <512>;
224 marvell,nand-enable-arbiter;
227 compatible = "fixed-partitions";
228 #address-cells = <1>;
229 #size-cells = <1>;
241 label = "nand-bbt";