Lines Matching +full:usb +full:- +full:uart +full:- +full:rx
1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
5 * Based on sun8i-h3-bananapi-m2-plus.dts, which is:
6 * Copyright (C) 2016 Chen-Yu Tsai <wens@csie.org>
9 /dts-v1/;
10 #include "sun8i-h3.dtsi"
11 #include "sunxi-common-regulators.dtsi"
13 #include <dt-bindings/gpio/gpio.h>
14 #include <dt-bindings/input/input.h>
17 model = "Banana Pi BPI-M2-Zero";
18 compatible = "sinovoip,bpi-m2-zero", "allwinner,sun8i-h2-plus";
26 stdout-path = "serial0:115200n8";
30 compatible = "hdmi-connector";
35 remote-endpoint = <&hdmi_out_con>;
41 compatible = "gpio-leds";
44 label = "bananapi-m2-zero:red:pwr";
46 default-state = "on";
50 gpio-keys {
51 compatible = "gpio-keys";
53 switch-4 {
57 wakeup-source;
61 reg_vdd_cpux: vdd-cpux-regulator {
62 compatible = "regulator-gpio";
63 regulator-name = "vdd-cpux";
64 regulator-type = "voltage";
65 regulator-boot-on;
66 regulator-always-on;
67 regulator-min-microvolt = <1100000>;
68 regulator-max-microvolt = <1300000>;
69 regulator-ramp-delay = <50>; /* 4ms */
72 enable-active-high;
73 gpios-states = <0x1>;
77 reg_vcc_dram: vcc-dram {
78 compatible = "regulator-fixed";
79 regulator-name = "vcc-dram";
80 regulator-min-microvolt = <1500000>;
81 regulator-max-microvolt = <1500000>;
82 regulator-always-on;
83 regulator-boot-on;
84 enable-active-high;
86 vin-supply = <®_vcc5v0>;
90 compatible = "regulator-fixed";
91 regulator-name = "vcc1v2";
92 regulator-min-microvolt = <1200000>;
93 regulator-max-microvolt = <1200000>;
94 regulator-always-on;
95 regulator-boot-on;
96 enable-active-high;
98 vin-supply = <®_vcc5v0>;
102 compatible = "regulator-poweroff";
103 cpu-supply = <®_vcc1v2>;
107 compatible = "mmc-pwrseq-simple";
108 reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
110 clock-names = "ext_clock";
115 cpu-supply = <®_vdd_cpux>;
132 remote-endpoint = <&hdmi_con_in>;
137 vmmc-supply = <®_vcc3v3>;
138 bus-width = <4>;
144 cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
149 vmmc-supply = <®_vcc3v3>;
150 vqmmc-supply = <®_vcc3v3>;
151 mmc-pwrseq = <&wifi_pwrseq>;
152 bus-width = <4>;
153 non-removable;
158 compatible = "brcm,bcm4329-fmac";
159 interrupt-parent = <&pio>;
161 interrupt-names = "host-wake";
170 pinctrl-names = "default";
171 pinctrl-0 = <&uart0_pa_pins>;
176 pinctrl-names = "default";
177 pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
178 uart-has-rtscts;
182 compatible = "brcm,bcm43438-bt";
183 max-speed = <1500000>;
185 clock-names = "lpo";
186 vbat-supply = <®_vcc3v3>;
187 vddio-supply = <®_vcc3v3>;
188 device-wakeup-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */
189 host-wakeup-gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
190 shutdown-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
196 gpio-line-names =
198 "CON2-P13", "CON2-P11", "CON2-P22", "CON2-P15",
199 "CON3-P03", "CON3-P02", "CON2-P07", "CON2-P29",
200 "CON2-P31", "CON2-P33", "CON2-P35", "CON2-P05",
201 "CON2-P03", "CON2-P08", "CON2-P10", "CON2-P16",
202 "CON2-P12", "CON2-P37", "CON2-P28", "CON2-P27",
203 "CON2-P40", "CON2-P38", "", "",
213 "CON2-P19", "CON2-P21", "CON2-P23", "CON2-P24",
214 "CON2-P18", "", "", "CON2-P26",
221 "", "", "", "", "", "", "CSI-PWR-EN", "",
226 "CN3-P17", "CN3-P13", "CN3-P09", "CN3-P07",
227 "CN3-P19", "CN3-P21", "CN3-P22", "CN3-P20",
228 "CN3-P18", "CN3-P16", "CN3-P14", "CN3-P12",
229 "CN3-P05", "CN3-P03", "CN3-P06", "CN3-P08",
234 "SDC0-D1", "SDC0-D0", "SDC0-CLK", "SDC0-CMD", "SDC0-D3",
235 "SDC0-D2", "SDC0-DET", "",
241 "WL-SDIO-CLK", "WL-SDIO-CMD", "WL-SDIO-D0", "WL-SDIO-D1",
242 "WL-SDIO-D2", "WL-SDIO-D3", "BT-UART-TX", "BT-UART-RX",
243 "BT-UART-RTS", "BT-UART-CTS", "WL-WAKE-AP", "BT-WAKE-AP",
244 "BT-RST-N", "AP-WAKE-BT", "", "",
250 gpio-line-names =
252 "", "CPUX-SET", "CON2-P32", "POWER-KEY", "CON2-P36",
253 "VCC-IO-EN", "USB0-ID", "WL-PWR-EN",
254 "PWR-STB", "PWR-DRAM", "PWR-LED", "IR-RX", "", "", "", "",
265 usb0_id_det-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
267 * There're two micro-USB connectors, one is power-only and another is
269 * the external USB device will be powered just by the power input
270 * from the power-only USB port.