Lines Matching +full:slew +full:- +full:time +full:- +full:us
1 .. SPDX-License-Identifier: GPL-2.0
28 AIC-7901A Single Channel 64-bit PCI-X 133MHz to
30 AIC-7901B Single Channel 64-bit PCI-X 133MHz to
32 AIC-7902A4 Dual Channel 64-bit PCI-X 133MHz to
34 AIC-7902B Dual Channel 64-bit PCI-X 133MHz to
41 Adaptec SCSI Card 39320 Dual Channel 64-bit PCI-X 133MHz to 7902A4/7902B
43 68-pin, two internal 68-pin)
44 Adaptec SCSI Card 39320A Dual Channel 64-bit PCI-X 133MHz to 7902B
46 68-pin, two internal 68-pin)
47 Adaptec SCSI Card 39320D Dual Channel 64-bit PCI-X 133MHz to 7902A4
49 and one internal 68-pin)
50 Adaptec SCSI Card 39320D Dual Channel 64-bit PCI-X 133MHz to 7902A4
52 and one internal 68-pin) based on the
53 AIC-7902B ASIC
54 Adaptec SCSI Card 29320 Single Channel 64-bit PCI-X 133MHz to 7901A
56 68-pin, two internal 68-pin, one
57 internal 50-pin)
58 Adaptec SCSI Card 29320A Single Channel 64-bit PCI-X 133MHz to 7901B
60 68-pin, two internal 68-pin, one
61 internal 50-pin)
62 Adaptec SCSI Card 29320LP Single Channel 64-bit Low Profile 7901A
63 PCI-X 133MHz to Ultra320 SCSI Card
65 68-pin)
66 Adaptec SCSI Card 29320ALP Single Channel 64-bit Low Profile 7901B
67 PCI-X 133MHz to Ultra320 SCSI Card
69 68-pin)
77 - Updated driver to use SCSI transport class infrastructure
78 - Upported sequencer and core fixes from adaptec released
82 - Fix several deadlock issues.
83 - Add 29320ALP and 39320B Id's.
86 - Align the SCB_TAG field on a 16byte boundary. This avoids
87 SCB corruption on some PCI-33 busses.
88 - Correct non-zero luns on Rev B. hardware.
89 - Update for change in 2.5.X SCSI proc FS interface.
90 - When negotiation async via an 8bit WDTR message, send
94 - Implement controller suspend and resume.
95 - Clear PCI error state during driver attach so that we
101 - Fix compiler errors.
102 - Remove S/G splitting for segments that cross a 4GB boundary.
104 - Add support for scsi_report_device_reset() found in
106 - Add 7901B support.
107 - Simplify handling of the packetized lun Rev A workaround.
108 - Correct and simplify handling of the ignore wide residue
114 - Fix types accessed via the command line interface code.
115 - Perform a few firmware optimizations.
116 - Fix "Unexpected PKT busfree" errors.
117 - Use a sequencer interrupt to notify the host of
120 that the host is interrupted for as short a time as
122 - Remove pre-2.2.X support.
123 - Add support for new 2.5.X interrupt API.
124 - Correct big-endian architecture support.
127 - Use del_timer_sync() to ensure that no timeouts
129 - For pre-2.5.X kernels, carefully adjust our segment
131 - Cleanup channel display in our /proc output.
132 - Workaround duplicate device entries in the mid-layer
133 device list during add-single-device.
136 - Correct a double free in the Domain Validation code.
137 - Correct a reference to free'ed memory during controller
139 - Reset the bus on an SE->LVD change. This is required
143 - Fix a few register window mode bugs.
144 - Include read streaming in the PPR flags we display in
146 - Add PCI hot plug support for 2.5.X kernels.
147 - Correct default precompensation value for RevA hardware.
148 - Fix Domain Validation thread shutdown.
149 - Add a firmware workaround to make the LED blink
151 - Correct /proc display of user read streaming settings.
152 - Simplify driver locking by releasing the io_request_lock
153 upon driver entry from the mid-layer.
154 - Cleanup command line parsing and move much of this code
158 - Correct a race condition in our error recovery handler.
159 - Allow Test Unit Ready commands to take a full 5 seconds
163 - Correct a Rev B. regression due to the GEM318
167 - Add support for the 39320A.
168 - Improve recovery for certain PCI-X errors.
169 - Fix handling of LQ/DATA/LQ/DATA for the
172 - Correct compatibility issues with the GEM318
174 - Correct data corruption issue that occurred under
176 - Adapt to a change in the 2.5.X daemonize() API.
177 - Correct a "Missing case in ahd_handle_scsiint" panic.
180 - Full regression testing for all U320 products completed.
181 - Added abort and target/lun reset error recovery handler and
185 - Added support for Domain Validation
186 - Add support for the Hewlett-Packard version of the 39320D
187 and AIC-7902 adapters.
193 - Added support for the Linux 2.5.X kernel series
196 - Added support for four additional SCSI products:
197 ASC-39320, ASC-29320, ASC-29320LP, AIC-7901.
200 - Initial driver release.
203 - Support for the SPI-4 "Ultra320" standard:
204 - 320MB/s transfer rates
205 - Packetized SCSI Protocol at 160MB/s and 320MB/s
206 - Quick Arbitration Selection (QAS)
207 - Retained Training Information (Rev B. ASIC only)
208 - Interrupt Coalescing
209 - Initiator Mode (target mode not currently
211 - Support for the PCI-X standard up to 133MHz
212 - Support for the PCI v2.2 standard
213 - Domain Validation
216 - Redhat Linux 7.2, 7.3, 8.0, Advanced Server 2.1
217 - SuSE Linux 7.3, 8.0, 8.1, Enterprise Server 7
218 - only Intel and AMD x86 supported at this time
219 - >4GB memory configurations supported.
278 :Possible Values: 1 - 253
282 :Definition: Set the per-target tagged queue depth on a
287 :Possible Values: 1 - 253
299 - specifies a tag depth of 16 for target 0
300 - specifies a tag depth of 64 for target 3
301 - specifies a tag depth of 8 for targets 4 and 5
302 - leaves target 6 at the default
303 - specifies a tag depth of 32 for targets 1,2,7-15
313 - specifies a tag depth of 32 for targets 0 and 2
334 - enables read streaming for targets 0 and 6.
335 - disables read streaming for targets 1-5,7-15.
346 - enables read streaming for targets 1,2, and 5.
347 - disables read streaming for targets 3,4,6-15.
351 - enables read streaming for all targets.
356 :Possible Values: 0x0000 - 0xffff
360 :Definition: Set Domain Validation Policy on a per-controller basis.
378 dv:{-1,0,,1,1,0}
380 - On Controller 0 leave DV at its default setting.
381 - On Controller 1 disable DV.
382 - Skip configuration on Controller 2.
383 - On Controllers 3 and 4 enable DV.
384 - On Controller 5 disable DV.
398 :Definition: Set IO Cell precompensation value on a per-controller basis.
402 :Possible Values: 0 - 7
417 - On Controller 0 set precompensation to 1.
418 - On Controller 2 set precompensation to 8.
421 :Definition: Set IO Cell slew rate on a per-controller basis.
423 they should retain the default slew rate setting.
425 :Possible Values: 0 - 15
434 - On Controller 0 set slew rate to 1.
440 - On Controller 0 set slew rate to 1.
441 - On Controller 2 set slew rate to 8.
444 :Definition: Set IO Cell signal amplitude on a per-controller basis.
448 :Possible Values: 1 - 7
463 - On Controller 0 set amplitude to 1.
464 - On Controller 2 set amplitude to 7.
477 -----------------------------------
484 4.2. Third-Party Compatibility Issues
485 -------------------------------------
493 -----------------------------------------------
500 manually probing non-contiguous luns.
517 - The 12-digit TSID can be found on the white barcode-type label
518 included inside the box with your product. The TSID helps us
523 - Search the Adaptec Support Knowledgebase (ASK) at
526 - For support via Email, submit your question to Adaptec's
530 - Visit our Web site at http://www.adaptec.com/.
531 - For information about Adaptec's support options, call
532 408-957-2550, 24 hours a day, 7 days a week.
533 - To speak with a Technical Support Specialist,
535 * For hardware products, call 408-934-7274,
537 * For RAID and Fibre Channel products, call 321-207-2000,
541 - To order Adaptec products, including accessories and cables,
542 call 408-957-7274. To order cables online go to
543 http://www.adaptec.com/buy-cables/.
546 - Visit our Web site at http://www.adaptec.com/en-US/_common/world_index.
547 - To speak with a Technical Support Specialist, call, or email,
549 * German: +49 89 4366 5522, Monday-Friday, 9:00-17:00 CET,
550 http://ask-de.adaptec.com/.
551 * French: +49 89 4366 5533, Monday-Friday, 9:00-17:00 CET,
552 http://ask-fr.adaptec.com/.
553 * English: +49 89 4366 5544, Monday-Friday, 9:00-17:00 GMT,
556 - You can order Adaptec cables online at
557 http://www.adaptec.com/buy-cables/.
560 - Visit our web site at http://www.adaptec.co.jp/.
561 - To speak with a Technical Support Specialist, call
562 +81 3 5308 6120, Monday-Friday, 9:00 a.m. to 12:00 p.m.,
585 WARRANTIES OF NON-INFRINGEMENT OR THE IMPLIED WARRANTIES OF MERCHANTABILITY