Lines Matching +full:a +full:- +full:8
10 Addresses scanned: from Super I/O config space (8 I/O ports)
18 Addresses scanned: from Super I/O config space (8 I/O ports)
24 Addresses scanned: from Super I/O config space (8 I/O ports)
32 Addresses scanned: from Super I/O config space (8 I/O ports)
40 Addresses scanned: from Super I/O config space (8 I/O ports)
48 Addresses scanned: from Super I/O config space (8 I/O ports)
56 Addresses scanned: from Super I/O config space (8 I/O ports)
64 Addresses scanned: from Super I/O config space (8 I/O ports)
72 Addresses scanned: from Super I/O config space (8 I/O ports)
80 Addresses scanned: from Super I/O config space (8 I/O ports)
88 Addresses scanned: from Super I/O config space (8 I/O ports)
96 Addresses scanned: from Super I/O config space (8 I/O ports)
104 Addresses scanned: from Super I/O config space (8 I/O ports)
112 Addresses scanned: from Super I/O config space (8 I/O ports)
120 Addresses scanned: from Super I/O config space (8 I/O ports)
128 Addresses scanned: from Super I/O config space (8 I/O ports)
136 Addresses scanned: from Super I/O config space (8 I/O ports)
144 Addresses scanned: from Super I/O config space (8 I/O ports)
152 Addresses scanned: from Super I/O config space (8 I/O ports)
160 Addresses scanned: from Super I/O config space (8 I/O ports)
168 Addresses scanned: from Super I/O config space (8 I/O ports)
174 - Christophe Gauthron
175 - Jean Delvare <jdelvare@suse.de>
179 -----------------
192 misconfigured by BIOS - PWM values would be inverted. This option tries
198 For example "force_id=0x8689,0x8633". A value of 0 is ignored
200 Note: A single force_id value (e.g. "force_id=0x8689") is used for
209 Provided since there are reports that system-wide acpi_enfore_resources=lax
217 -------------------
219 All the chips supported by this driver are LPC Super-I/O chips, accessed
220 through the LPC bus (ISA-like I/O ports). The IT8712F additionally has an
223 than the ISA access, and was only available on a small number of
228 -----------
238 rotation speed sensors, 8 voltage sensors, associated alarms, and chassis
244 though, so the functionality may not be available on a given system.
246 The IT8718F and IT8720F also features VID inputs (up to 8 pins) but the value
247 is stored in the Super-I/O configuration space. Due to technical limitations,
251 can't have both on a given board.
258 IT8783E/F, and late IT8712F and IT8705F also have optional 16-bit tachometer
260 not compatible with the older chips and revisions. The 16-bit tachometer mode
268 until a datasheet becomes available (hopefully.)
270 The IT8603E/IT8623E is a custom design, hardware monitoring part is similar to
271 IT8728F. It only supports 3 fans, 16-bit fan mode, and the full speed mode
275 to IT8728F. It only supports 16-bit fan mode. Both chips support up to 6 fans.
277 The IT8790E, IT8792E/IT8795E and IT87952E support up to 3 fans. 16-bit fan
280 The IT8732F supports a closed-loop mode for fan control, but this is not
287 triggered if the rotation speed has dropped below a programmable limit. When
288 16-bit tachometer counters aren't used, fan readings can be divided by
289 a programmable divider (1, 2, 4 or 8) to give the readings more range or
290 accuracy. With a divider of 2, the lowest representable value is around
295 alarm is triggered if the voltage has crossed a programmable minimum or
298 voltage inputs can measure voltages between 0 and 4.08 volts, with a resolution
300 3.06 volts, with a resolution of 0.012 volt. IT8732F can measure between 0 and
301 2.8 volts with a resolution of 0.0109 volt. The battery voltage in8 does not
310 The driver handles this transparently so user-space doesn't have to care.
314 the mainboard and/or processor itself. It is a value in volts.
321 once-only alarms.
323 Out-of-limit readings can also result in beeping, if the chip is properly
330 To change sensor N to a thermistor, 'echo 4 > tempN_type' where N is 1, 2,
331 or 3. To change sensor N to a thermal diode, 'echo 3 > tempN_type'.
338 -----------------
347 it may give you a somewhat greater control range. The same frequency is
349 read-only.
353 -------------------------------------------
379 -----------------------------
381 The driver supports temp[1-3]_offset sysfs attributes to adjust the reported
382 temperature for thermal diodes or diode-connected thermal transistors.
383 If a temperature sensor is configured for thermistors, the attribute values