Lines Matching +full:tegra124 +full:- +full:pinmux
1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/soc/tegra/nvidia,tegra20-pmc.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Thierry Reding <thierry.reding@gmail.com>
11 - Jonathan Hunter <jonathanh@nvidia.com>
16 - nvidia,tegra20-pmc
17 - nvidia,tegra30-pmc
18 - nvidia,tegra114-pmc
19 - nvidia,tegra124-pmc
20 - nvidia,tegra210-pmc
25 clock-names:
28 - const: pclk
30 - const: clk32k_in
35 '#clock-cells':
43 include/dt-bindings/soc/tegra-pmc.h for the list of Tegra PMC clock IDs.
45 '#interrupt-cells':
50 interrupt-controller: true
52 nvidia,invert-interrupt:
60 nvidia,core-power-req-active-high:
62 description: core power request active-high
64 nvidia,sys-clock-req-active-high:
66 description: system clock request active-high
68 nvidia,combined-power-req:
72 nvidia,cpu-pwr-good-en:
76 nvidia,suspend-mode:
80 - description: LP0, CPU + Core voltage off and DRAM in self-refresh
82 - description: LP1, CPU voltage off and DRAM in self-refresh
84 - description: LP2, CPU voltage off
87 nvidia,cpu-pwr-good-time:
91 nvidia,cpu-pwr-off-time:
95 nvidia,core-pwr-good-time:
96 $ref: /schemas/types.yaml#/definitions/uint32-array
99 - description: oscillator stable time
100 - description: power stable time
102 nvidia,core-pwr-off-time:
106 nvidia,lp0-vec:
107 $ref: /schemas/types.yaml#/definitions/uint32-array
111 The AVP (Audio-Video Processor) is an ARM7 processor and always being
117 - description: starting address of LP0 vector
118 - description: length of LP0 vector
120 core-supply:
124 core-domain:
131 operating-points-v2:
132 description: Should contain level, voltages and opp-supported-hw
133 property. The supported-hw is a bitfield indicating SoC speedo or
136 "#power-domain-cells":
140 - operating-points-v2
141 - "#power-domain-cells"
143 i2c-thermtrip:
145 description: On Tegra30, Tegra114 and Tegra124 if i2c-thermtrip subnode
146 exists, hardware-triggered thermal reset will be enabled.
149 nvidia,i2c-controller-id:
155 nvidia,bus-addr:
159 nvidia,reg-addr:
163 nvidia,reg-data:
165 description: power-off command to write to PMU
167 nvidia,pinmux-id:
169 description: Pinmux used by the hardware when issuing power-off command.
170 Defaults to 0. Valid values are described in section 12.5.2 "Pinmux
174 - nvidia,i2c-controller-id
175 - nvidia,bus-addr
176 - nvidia,reg-addr
177 - nvidia,reg-data
184 the powergates on the Tegra SoC. Each powergate node represents a power-
185 domain on the Tegra SoC that can be power-gated by the Tegra PMC.
187 Hardware blocks belonging to a power domain should contain "power-domains"
195 for each power-gate block inside Tegra.
198 --------------------------------------------------------------
207 iram Internal RAM Tegra124/210
213 sor Display interfaces Tegra124/210
217 vic Video Imaging Compositor Tegra124/210
223 "^[a-z0-9]+$":
235 power-domains:
238 '#power-domain-cells':
243 - clocks
244 - resets
245 - '#power-domain-cells'
247 pinmux:
265 Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
270 The following pads are present on Tegra124 and Tegra132:
273 hsic, hv, lvds, mipi-bias, nand, pex-bias, pex-clk1, pex-clk2,
274 pex-cntrl, sdmmc1, sdmmc3, sdmmc4, sys_ddc, uart, usb0, usb1, usb2,
279 audio, audio-hv, cam, csia, csib, csic, csid, csie, csif, dbg,
280 debug-nonao, dmic, dp, dsi, dsib, dsic, dsid, emmc, emmc2, gpio,
281 hdmi, hsic, lvds, mipi-bias, pex-bias, pex-clk1, pex-clk2, pex-cntrl,
282 sdmmc1, sdmmc3, spi, spi-hv, uart, usb0, usb1, usb2, usb3, usb-bias
286 $ref: /schemas/types.yaml#/definitions/string-array
289 low-power-enable:
293 low-power-disable:
297 power-source:
304 include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h
306 Power state can be configured on all Tegra124 and Tegra132 pads.
307 None of the Tegra124 or Tegra132 pads support signaling voltage
308 switching. All of the listed Tegra210 pads except pex-cntrl support
312 audio, audio-hv, cam, dbg, dmic, gpio, pex-cntrl, sdmmc1, sdmmc3,
313 spi, spi-hv, uart
316 - pins
319 - compatible
320 - reg
321 - clock-names
322 - clocks
323 - '#clock-cells'
326 - if:
330 const: nvidia,tegra124-pmc
333 pinmux:
340 dsic, dsid, hdmi, hsic, hv, lvds, mipi-bias, nand,
341 pex-bias, pex-clk1, pex-clk2, pex-cntrl, sdmmc1,
345 - if:
349 const: nvidia,tegra210-pmc
352 pinmux:
358 enum: [ audio, audio-hv, cam, csia, csib, csic, csid, csie,
359 csif, dbg, debug-nonao, dmic, dp, dsi, dsib, dsic,
360 dsid, emmc, emmc2, gpio, hdmi, hsic, lvds, mipi-bias,
361 pex-bias, pex-clk1, pex-clk2, pex-cntrl, sdmmc1,
362 sdmmc3, spi, spi-hv, uart, usb0, usb1, usb2, usb3,
363 usb-bias ]
368 nvidia,suspend-mode: ["nvidia,core-pwr-off-time", "nvidia,cpu-pwr-off-time"]
369 nvidia,core-pwr-off-time: ["nvidia,core-pwr-good-time"]
370 nvidia,cpu-pwr-off-time: ["nvidia,cpu-pwr-good-time"]
373 - |
374 #include <dt-bindings/clock/tegra210-car.h>
375 #include <dt-bindings/pinctrl/pinctrl-tegra-io-pad.h>
376 #include <dt-bindings/soc/tegra-pmc.h>
379 compatible = "nvidia,tegra210-pmc";
381 core-supply = <®ulator>;
383 clock-names = "pclk", "clk32k_in";
384 #clock-cells = <1>;
386 nvidia,invert-interrupt;
387 nvidia,suspend-mode = <0>;
388 nvidia,cpu-pwr-good-time = <0>;
389 nvidia,cpu-pwr-off-time = <0>;
390 nvidia,core-pwr-good-time = <4587 3876>;
391 nvidia,core-pwr-off-time = <39065>;
392 nvidia,core-power-req-active-high;
393 nvidia,sys-clock-req-active-high;
395 pd_core: core-domain {
396 operating-points-v2 = <&core_opp_table>;
397 #power-domain-cells = <0>;
405 power-domains = <&pd_core>;
406 #power-domain-cells = <0>;
412 power-domains = <&pd_core>;
413 #power-domain-cells = <0>;