Lines Matching +full:external +full:- +full:falling
2 ----------------------------
4 (c) 2006-2009 Secret Lab Technologies Ltd
8 ------------------
9 For mpc5200 on-chip devices, the format for each compatible value is
10 <chip>-<device>[-<mode>]. The OS should be able to match a device driver
21 "fsl,mpc5200-<device>".
29 compatible = "fsl,mpc5200b-<device>","fsl,mpc5200-<device>";
34 ie. ethernet on mpc5200: compatible = "fsl,mpc5200-fec";
35 ethernet on mpc5200b: compatible = "fsl,mpc5200b-fec", "fsl,mpc5200-fec";
39 "fsl,mpc5200-psc-i2s", not "fsl,mpc5200-i2s". This convention is chosen to
40 avoid naming conflicts with non-psc devices providing the same
41 function. For example, "fsl,mpc5200-spi" and "fsl,mpc5200-psc-spi" describe
48 ------------
55 ---- -----------
59 compatible mpc5200: "fsl,mpc5200-immr"
60 mpc5200b: "fsl,mpc5200b-immr"
61 system-frequency 'fsystem' frequency in Hz; XLB, IPB, USB and PCI
63 bus-frequency IPB bus frequency in Hz. Clock rate
67 ---------------
71 tree should use the "fsl,mpc5200b-<device>","fsl,mpc5200-<device>" form.
75 ---- ---------- -----------
76 cdm@<addr> fsl,mpc5200-cdm Clock Distribution
77 interrupt-controller@<addr> fsl,mpc5200-pic need an interrupt
79 bestcomm@<addr> fsl,mpc5200-bestcomm Bestcomm DMA controller
83 ---- ---------- -----------
84 timer@<addr> fsl,mpc5200-gpt General purpose timers
85 gpio@<addr> fsl,mpc5200-gpio MPC5200 simple gpio controller
86 gpio@<addr> fsl,mpc5200-gpio-wkup MPC5200 wakeup gpio controller
87 rtc@<addr> fsl,mpc5200-rtc Real time clock
88 mscan@<addr> fsl,mpc5200-mscan CAN bus controller
89 pci@<addr> fsl,mpc5200-pci PCI bridge
90 serial@<addr> fsl,mpc5200-psc-uart PSC in serial mode
91 i2s@<addr> fsl,mpc5200-psc-i2s PSC in i2s mode
92 ac97@<addr> fsl,mpc5200-psc-ac97 PSC in ac97 mode
93 spi@<addr> fsl,mpc5200-psc-spi PSC in spi mode
94 irda@<addr> fsl,mpc5200-psc-irda PSC in IrDA mode
95 spi@<addr> fsl,mpc5200-spi MPC5200 spi device
96 ethernet@<addr> fsl,mpc5200-fec MPC5200 ethernet device
97 ata@<addr> fsl,mpc5200-ata IDE ATA interface
98 i2c@<addr> fsl,mpc5200-i2c I2C controller
99 usb@<addr> fsl,mpc5200-ohci,ohci-be USB controller
100 xlb@<addr> fsl,mpc5200-xlb XLB arbitrator
102 fsl,mpc5200-gpt nodes
103 ---------------------
106 include the empty property 'fsl,has-wdt'. Note that this does not activate
110 gpt api call to this timer will fail with -EBUSY.
113 fsl,wdt-on-boot = <n>;
114 GPT0 will be marked as in-use watchdog, i.e. blocking every gpt access to it.
117 - just mark GPT0 as watchdog, blocking gpt accesses, and configure it later;
118 - do not touch a configuration assigned by the boot loader which supervises
123 An mpc5200-gpt can be used as a single line GPIO controller. To do so,
125 gpio-controller;
126 #gpio-cells = <2>;
131 An mpc5200-gpt can be used as a single line edge sensitive interrupt
133 interrupt-controller;
134 #interrupt-cells = <1>;
136 sense mode; 1 for edge rising, 2 for edge falling.
138 fsl,mpc5200-psc nodes
139 ---------------------
140 The PSCs should include a cell-index which is the index of the PSC in
141 hardware. cell-index is used to determine which shared SoC registers to
142 use when setting up PSC clocking. cell-index number starts at '0'. ie:
143 PSC1 has 'cell-index = <0>'
144 PSC4 has 'cell-index = <3>'
147 i2s mode. An 'mpc5200b-psc-i2s' node cannot include 'mpc5200-psc-i2s' in the
151 fsl,mpc5200-gpio and fsl,mpc5200-gpio-wkup nodes
152 ------------------------------------------------
153 Each GPIO controller node should have the empty property gpio-controller and
154 #gpio-cells set to 2. First cell is the GPIO number which is interpreted
158 fsl,mpc5200-fec nodes
159 ---------------------
162 - fsl,7-wire-mode - An empty property that specifies the link uses 7-wire
164 - current-speed - Specifies that the MII should be configured for a fixed
168 - phy-handle - Contains a phandle to an Ethernet PHY.
170 Interrupt controller (fsl,mpc5200-pic) node
171 -------------------------------------------
187 For external IRQs, use the following interrupt property values (how to
188 specify external interrupts is a frequently asked question):
189 External interrupts:
190 external irq0: interrupts = <0 0 n>;
191 external irq1: interrupts = <1 1 n>;
192 external irq2: interrupts = <1 2 n>;
193 external irq3: interrupts = <1 3 n>;
194 'n' is sense (0: level high, 1: edge rising, 2: edge falling 3: level low)
196 fsl,mpc5200-mscan nodes
197 -----------------------