Lines Matching +full:synclko +full:- +full:125
1 # SPDX-License-Identifier: GPL-2.0-only
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Marek Vasut <marex@denx.de>
11 - Woojung Huh <Woojung.Huh@microchip.com>
14 - $ref: /schemas/spi/spi-peripheral-props.yaml#
21 - microchip,ksz8765
22 - microchip,ksz8794
23 - microchip,ksz8795
24 - microchip,ksz8863
25 - microchip,ksz8864 # 4-port version of KSZ8895 family switch
26 - microchip,ksz8873
27 - microchip,ksz8895 # 5-port version of KSZ8895 family switch
28 - microchip,ksz9477
29 - microchip,ksz9897
30 - microchip,ksz9896
31 - microchip,ksz9567
32 - microchip,ksz8565
33 - microchip,ksz9893
34 - microchip,ksz9563
35 - microchip,ksz8563
36 - microchip,ksz8567
37 - microchip,lan9646
39 reset-gpios:
44 wakeup-source: true
46 microchip,synclko-125:
49 Set if the output SYNCLKO frequency should be set to 125MHz instead of 25MHz.
51 microchip,synclko-disable:
54 Set if the output SYNCLKO clock should be disabled. Do not mix with
55 microchip,synclko-125.
57 microchip,pme-active-high:
60 Indicates if the PME pin polarity is active-high.
62 microchip,io-drive-strength-microamp:
68 microchip,hi-drive-strength-microamp:
75 microchip,lo-drive-strength-microamp:
89 mdio-parent-bus:
98 "^ethernet-phy@[0-9a-f]$":
100 $ref: /schemas/net/ethernet-phy.yaml#
106 - compatible
107 - reg
114 - microchip,ksz8863
115 - microchip,ksz8873
117 $ref: dsa.yaml#/$defs/ethernet-ports
120 "^(ethernet-)?ports$":
122 "^(ethernet-)?port@[0-2]$":
123 $ref: dsa-port.yaml#
126 microchip,rmii-clk-internal:
136 If microchip,rmii-clk-internal is set, ksz88x3 will provide
140 microchip,rmii-clk-internal: [ethernet]
145 - |
146 #include <dt-bindings/gpio/gpio.h>
150 fixed-link {
152 full-duplex;
157 #address-cells = <1>;
158 #size-cells = <0>;
160 pinctrl-0 = <&pinctrl_spi_ksz>;
161 cs-gpios = <&pioC 25 0>;
166 reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
168 spi-max-frequency = <44000000>;
170 ethernet-ports {
171 #address-cells = <1>;
172 #size-cells = <0>;
196 phy-mode = "rgmii";
198 fixed-link {
200 full-duplex;
210 spi-max-frequency = <44000000>;
212 ethernet-ports {
213 #address-cells = <1>;
214 #size-cells = <0>;
234 phy-mode = "rgmii";
236 fixed-link {
238 full-duplex;