Lines Matching +full:multi +full:- +full:led
1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Arınç ÜNAL <arinc.unal@arinc9.com>
11 - Landen Chao <Landen.Chao@mediatek.com>
12 - DENG Qingfang <dqfext@gmail.com>
13 - Sean Wang <sean.wang@mediatek.com>
14 - Daniel Golle <daniel@makrotopia.org>
17 There are three versions of MT7530, standalone, in a multi-chip module and
18 built-into a SoC.
20 MT7530 is a part of the multi-chip module in MT7620AN, MT7620DA, MT7620DAN,
23 The MT7988 SoC comes with a built-in switch similar to MT7531 as well as four
26 CPU port and 4 user ports connected to the built-in Gigabit Ethernet PHYs.
36 - Port 5 can be used as a CPU port.
38 - PHY 0 or 4 of the switch can be muxed to gmac5 of the switch. Therefore,
43 The driver looks up the reg on the ethernet-phy node, which the phy-handle
46 The driver requires the gmac of the SoC to have "mediatek,eth-mac" as the
48 MediaTek SoC can benefit this. Banana Pi BPI-R2 suits this.
54 - For the multi-chip module MT7530, in case of an external phy wired to
63 - Port 5 can be wired to an external phy. Port 5 becomes a DSA user port.
65 For the multi-chip module MT7530, the external phy must be wired TX to TX
69 For the multi-chip module MT7530, muxing PHY 0 or 4 won't work when the
79 - description:
80 Standalone MT7530 and multi-chip module MT7530 in MT7623AI SoC
83 - description:
87 - description:
88 Multi-chip module MT7530 in MT7621AT, MT7621DAT and MT7621ST SoCs
91 - description:
92 Built-in switch of the MT7988 SoC
93 const: mediatek,mt7988-switch
95 - description:
96 Built-in switch of the Airoha EN7581 SoC
97 const: airoha,en7581-switch
99 - description:
100 Built-in switch of the Airoha AN7583 SoC
101 const: airoha,an7583-switch
106 core-supply:
110 "#gpio-cells":
113 gpio-controller:
116 If defined, LED controller of the MT7530 switch will run on GPIO mode.
119 port 0 LED 0..2 as GPIO 0..2
120 port 1 LED 0..2 as GPIO 3..5
121 port 2 LED 0..2 as GPIO 6..8
122 port 3 LED 0..2 as GPIO 9..11
123 port 4 LED 0..2 as GPIO 12..14
125 "#interrupt-cells":
128 interrupt-controller: true
133 io-supply:
136 See Documentation/devicetree/bindings/regulator/mt6323-regulator.txt for
153 switch is a part of the multi-chip module.
155 reset-gpios:
163 reset-names:
173 "^(ethernet-)?ports$":
178 "^(ethernet-)?port@[0-6]$":
189 - if:
195 - 5
196 - 6
199 - compatible
200 - reg
203 builtin-dsa-port:
205 "^(ethernet-)?ports$":
207 "^(ethernet-)?port@[0-6]$":
212 phy-mode:
215 mt7530-dsa-port:
217 "^(ethernet-)?ports$":
219 "^(ethernet-)?port@[0-6]$":
229 phy-mode:
231 - gmii
232 - mii
233 - rgmii
236 phy-mode:
238 - rgmii
239 - trgmii
241 mt7531-dsa-port:
243 "^(ethernet-)?ports$":
245 "^(ethernet-)?port@[0-6]$":
255 phy-mode:
257 - 1000base-x
258 - 2500base-x
259 - rgmii
260 - sgmii
263 phy-mode:
265 - 1000base-x
266 - 2500base-x
267 - sgmii
270 - $ref: dsa.yaml#/$defs/ethernet-ports
271 - if:
273 - mediatek,mcm
276 reset-gpios: false
279 - resets
280 - reset-names
282 - dependencies:
283 interrupt-controller: [ interrupts ]
285 - if:
290 $ref: "#/$defs/mt7530-dsa-port"
292 - core-supply
293 - io-supply
295 - if:
300 $ref: "#/$defs/mt7531-dsa-port"
302 gpio-controller: false
305 - if:
310 $ref: "#/$defs/mt7530-dsa-port"
312 - mediatek,mcm
314 - if:
318 - mediatek,mt7988-switch
319 - airoha,en7581-switch
320 - airoha,an7583-switch
322 $ref: "#/$defs/builtin-dsa-port"
324 gpio-controller: false
326 reset-names: false
332 - |
333 #include <dt-bindings/gpio/gpio.h>
336 #address-cells = <1>;
337 #size-cells = <0>;
343 reset-gpios = <&pio 33 0>;
345 core-supply = <&mt6323_vpa_reg>;
346 io-supply = <&mt6323_vemc3v3_reg>;
348 ethernet-ports {
349 #address-cells = <1>;
350 #size-cells = <0>;
380 phy-mode = "rgmii";
382 fixed-link {
384 full-duplex;
393 - |
394 #include <dt-bindings/reset/mt2701-resets.h>
397 #address-cells = <1>;
398 #size-cells = <0>;
406 reset-names = "mcm";
408 core-supply = <&mt6323_vpa_reg>;
409 io-supply = <&mt6323_vemc3v3_reg>;
411 ethernet-ports {
412 #address-cells = <1>;
413 #size-cells = <0>;
443 phy-mode = "trgmii";
445 fixed-link {
447 full-duplex;
456 - |
457 #include <dt-bindings/gpio/gpio.h>
458 #include <dt-bindings/interrupt-controller/irq.h>
461 #address-cells = <1>;
462 #size-cells = <0>;
468 reset-gpios = <&pio 54 0>;
470 interrupt-controller;
471 #interrupt-cells = <1>;
472 interrupt-parent = <&pio>;
475 ethernet-ports {
476 #address-cells = <1>;
477 #size-cells = <0>;
507 phy-mode = "2500base-x";
509 fixed-link {
511 full-duplex;
520 - |
521 #include <dt-bindings/interrupt-controller/mips-gic.h>
522 #include <dt-bindings/reset/mt7621-reset.h>
525 #address-cells = <1>;
526 #size-cells = <0>;
534 reset-names = "mcm";
536 interrupt-controller;
537 #interrupt-cells = <1>;
538 interrupt-parent = <&gic>;
541 ethernet-ports {
542 #address-cells = <1>;
543 #size-cells = <0>;
573 phy-mode = "trgmii";
575 fixed-link {
577 full-duplex;
586 - |
587 #include <dt-bindings/interrupt-controller/mips-gic.h>
588 #include <dt-bindings/reset/mt7621-reset.h>
591 #address-cells = <1>;
592 #size-cells = <0>;
594 pinctrl-names = "default";
595 pinctrl-0 = <&rgmii2_pins>;
598 compatible = "mediatek,eth-mac";
601 phy-mode = "rgmii";
602 phy-handle = <&example5_ethphy4>;
606 #address-cells = <1>;
607 #size-cells = <0>;
610 example5_ethphy4: ethernet-phy@4 {
620 reset-names = "mcm";
622 interrupt-controller;
623 #interrupt-cells = <1>;
624 interrupt-parent = <&gic>;
627 ethernet-ports {
628 #address-cells = <1>;
629 #size-cells = <0>;
661 phy-mode = "trgmii";
663 fixed-link {
665 full-duplex;
675 - |
676 #include <dt-bindings/interrupt-controller/mips-gic.h>
677 #include <dt-bindings/reset/mt7621-reset.h>
680 #address-cells = <1>;
681 #size-cells = <0>;
683 pinctrl-names = "default";
684 pinctrl-0 = <&rgmii2_pins>;
687 compatible = "mediatek,eth-mac";
690 phy-mode = "rgmii";
691 phy-handle = <&example6_ethphy7>;
695 #address-cells = <1>;
696 #size-cells = <0>;
699 example6_ethphy7: ethernet-phy@7 {
701 phy-mode = "rgmii";
710 reset-names = "mcm";
712 interrupt-controller;
713 #interrupt-cells = <1>;
714 interrupt-parent = <&gic>;
717 ethernet-ports {
718 #address-cells = <1>;
719 #size-cells = <0>;
749 phy-mode = "trgmii";
751 fixed-link {
753 full-duplex;
763 - |
764 #include <dt-bindings/interrupt-controller/mips-gic.h>
765 #include <dt-bindings/reset/mt7621-reset.h>
768 #address-cells = <1>;
769 #size-cells = <0>;
771 pinctrl-names = "default";
772 pinctrl-0 = <&rgmii2_pins>;
775 #address-cells = <1>;
776 #size-cells = <0>;
779 example7_ethphy7: ethernet-phy@7 {
781 phy-mode = "rgmii";
790 reset-names = "mcm";
792 interrupt-controller;
793 #interrupt-cells = <1>;
794 interrupt-parent = <&gic>;
797 ethernet-ports {
798 #address-cells = <1>;
799 #size-cells = <0>;
829 phy-mode = "rgmii-txid";
830 phy-handle = <&example7_ethphy7>;
836 phy-mode = "trgmii";
838 fixed-link {
840 full-duplex;