Lines Matching +full:vsync +full:- +full:active +full:- +full:high
1 Device-Tree bindings for the NXP TDA1997x HDMI receiver
6 - RGB 8bit per color (24 bits total): R[11:4] B[11:4] G[11:4]
7 - YUV444 8bit per color (24 bits total): Y[11:4] Cr[11:4] Cb[11:4]
8 - YUV422 semi-planar 8bit per component (16 bits total): Y[11:4] CbCr[11:4]
9 - YUV422 semi-planar 10bit per component (20 bits total): Y[11:2] CbCr[11:2]
10 - YUV422 semi-planar 12bit per component (24 bits total): - Y[11:0] CbCr[11:0]
11 - YUV422 BT656 8bit per component (8 bits total): YCbCr[11:4] (2-cycles)
12 - YUV422 BT656 10bit per component (10 bits total): YCbCr[11:2] (2-cycles)
13 - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles)
16 - RGB 12bit per color (36 bits total): R[11:0] B[11:0] G[11:0]
17 - YUV444 12bit per color (36 bits total): Y[11:0] Cb[11:0] Cr[11:0]
18 - YUV422 semi-planar 12bit per component (24 bits total): Y[11:0] CbCr[11:0]
19 - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles)
21 The Video port output pins are mapped via 4-bit 'pin groups' allowing
23 pin groups. The video_portcfg device-tree property consists of register mapping
24 pairs which map a chip-specific VP output register to a 4-bit pin group. If
25 the pin group needs to be bit-swapped you can use the *_S pin-group defines.
28 - compatible :
29 - "nxp,tda19971" for the TDA19971
30 - "nxp,tda19973" for the TDA19973
31 - reg : I2C slave address
32 - interrupts : The interrupt number
33 - DOVDD-supply : Digital I/O supply
34 - DVDD-supply : Digital Core supply
35 - AVDD-supply : Analog supply
36 - nxp,vidout-portcfg : array of pairs mapping VP output pins to pin groups.
39 - nxp,audout-format : DAI bus format: "i2s" or "spdif".
40 - nxp,audout-width : width of audio output data bus (1-4).
41 - nxp,audout-layout : data layout (0=AP0 used, 1=AP0/AP1/AP2/AP3 used).
42 - nxp,audout-mclk-fs : Multiplication factor between stream rate and codec
47 Documentation/devicetree/bindings/media/video-interfaces.txt.
50 The following three properties are defined in video-interfaces.txt and
52 - hsync-active: Horizontal synchronization polarity. Defaults to active high.
53 - vsync-active: Vertical synchronization polarity. Defaults to active high.
54 - data-active: Data polarity. Defaults to active high.
57 - VP[15:0] connected to IMX6 CSI_DATA[19:4] for 16bit YUV422
59 hdmi-receiver@48 {
61 pinctrl-names = "default";
62 pinctrl-0 = <&pinctrl_tda1997x>;
64 interrupt-parent = <&gpio1>;
66 DOVDD-supply = <®_3p3v>;
67 AVDD-supply = <®_1p8v>;
68 DVDD-supply = <®_1p8v>;
70 #sound-dai-cells = <0>;
71 nxp,audout-format = "i2s";
72 nxp,audout-layout = <0>;
73 nxp,audout-width = <16>;
74 nxp,audout-mclk-fs = <128>;
76 * The 8bpp YUV422 semi-planar mode outputs CbCr[11:4]
79 nxp,vidout-portcfg =
80 /* Y[11:8]<->VP[15:12]<->CSI_DATA[19:16] */
82 /* Y[7:4]<->VP[11:08]<->CSI_DATA[15:12] */
84 /* CbCc[11:8]<->VP[07:04]<->CSI_DATA[11:8] */
86 /* CbCr[7:4]<->VP[03:00]<->CSI_DATA[7:4] */
91 remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
92 bus-width = <16>;
93 hsync-active = <1>;
94 vsync-active = <1>;
95 data-active = <1>;
99 - VP[15:8] connected to IMX6 CSI_DATA[19:12] for 8bit BT656
101 hdmi-receiver@48 {
103 pinctrl-names = "default";
104 pinctrl-0 = <&pinctrl_tda1997x>;
106 interrupt-parent = <&gpio1>;
108 DOVDD-supply = <®_3p3v>;
109 AVDD-supply = <®_1p8v>;
110 DVDD-supply = <®_1p8v>;
112 #sound-dai-cells = <0>;
113 nxp,audout-format = "i2s";
114 nxp,audout-layout = <0>;
115 nxp,audout-width = <16>;
116 nxp,audout-mclk-fs = <128>;
118 * The 8bpp YUV422 semi-planar mode outputs CbCr[11:4]
121 nxp,vidout-portcfg =
122 /* Y[11:8]<->VP[15:12]<->CSI_DATA[19:16] */
124 /* Y[7:4]<->VP[11:08]<->CSI_DATA[15:12] */
126 /* CbCc[11:8]<->VP[07:04]<->CSI_DATA[11:8] */
128 /* CbCr[7:4]<->VP[03:00]<->CSI_DATA[7:4] */
133 remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
134 bus-width = <16>;
135 hsync-active = <1>;
136 vsync-active = <1>;
137 data-active = <1>;
141 - VP[15:8] connected to IMX6 CSI_DATA[19:12] for 8bit BT656
143 hdmi-receiver@48 {
145 pinctrl-names = "default";
146 pinctrl-0 = <&pinctrl_tda1997x>;
148 interrupt-parent = <&gpio1>;
150 DOVDD-supply = <®_3p3v>;
151 AVDD-supply = <®_1p8v>;
152 DVDD-supply = <®_1p8v>;
154 #sound-dai-cells = <0>;
155 nxp,audout-format = "i2s";
156 nxp,audout-layout = <0>;
157 nxp,audout-width = <16>;
158 nxp,audout-mclk-fs = <128>;
163 nxp,vidout-portcfg =
164 /* YCbCr[11:8]<->VP[15:12]<->CSI_DATA[19:16] */
166 /* YCbCr[7:4]<->VP[11:08]<->CSI_DATA[15:12] */
171 remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
172 bus-width = <16>;
173 hsync-active = <1>;
174 vsync-active = <1>;
175 data-active = <1>;