Lines Matching +full:vdrive +full:- +full:supply
1 # SPDX-License-Identifier: GPL-2.0
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Michael Hennerich <michael.hennerich@analog.com>
14 https://www.analog.com/media/en/technical-documentation/data-sheets/AD7605-4.pdf
15 https://www.analog.com/media/en/technical-documentation/data-sheets/ad7606_7606-6_7606-4.pdf
16 https://www.analog.com/media/en/technical-documentation/data-sheets/AD7606B.pdf
17 https://www.analog.com/media/en/technical-documentation/data-sheets/AD7616.pdf
22 - adi,ad7605-4
23 - adi,ad7606-4
24 - adi,ad7606-6
25 - adi,ad7606-8 # Referred to as AD7606 (without -8) in the datasheet
26 - adi,ad7606b
27 - adi,ad7616
32 spi-cpha: true
34 spi-cpol: true
36 avcc-supply: true
38 vdrive-supply:
43 refin-supply:
45 The voltage supply for optional external reference voltage.
53 adi,conversion-start-gpios:
61 reset-gpios:
69 standby-gpios:
72 place the AD7606 into one of two power-down modes, Standby mode or
77 adi,first-data-gpios:
85 adi,range-gpios:
98 adi,oversampling-ratio-gpios:
100 Must be the device tree identifier of the over-sampling mode pins. As the
106 adi,sw-mode:
112 registers. If the adi,oversampling-ratio-gpios property is defined, then
118 - compatible
119 - reg
120 - spi-cpha
121 - avcc-supply
122 - vdrive-supply
123 - interrupts
124 - adi,conversion-start-gpios
127 - $ref: /schemas/spi/spi-peripheral-props.yaml#
129 - if:
136 adi,first-data-gpios: false
137 standby-gpios: false
138 adi,range-gpios:
142 adi,range-gpios:
145 - if:
150 - adi,ad7605-4
151 - adi,ad7616
154 adi,oversampling-ratio-gpios: false
156 - if:
161 - adi,ad7605-4
162 - adi,ad7606-4
163 - adi,ad7606-6
164 - adi,ad7606-8
167 adi,sw-mode: false
170 adi,conversion-start-gpios:
176 - |
177 #include <dt-bindings/gpio/gpio.h>
178 #include <dt-bindings/interrupt-controller/irq.h>
180 #address-cells = <1>;
181 #size-cells = <0>;
184 compatible = "adi,ad7606-8";
186 spi-max-frequency = <1000000>;
187 spi-cpol;
188 spi-cpha;
190 avcc-supply = <&adc_vref>;
191 vdrive-supply = <&vdd_supply>;
194 interrupt-parent = <&gpio>;
196 adi,conversion-start-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
197 reset-gpios = <&gpio 27 GPIO_ACTIVE_HIGH>;
198 adi,first-data-gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
199 adi,oversampling-ratio-gpios = <&gpio 18 GPIO_ACTIVE_HIGH>,
202 standby-gpios = <&gpio 24 GPIO_ACTIVE_LOW>;