Lines Matching +full:chip +full:- +full:selects
1 # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
11 external memory (such as NAND or other memory-mapped peripherals) whereas
17 NOR flash memories), WE (write enable). This on top of 6 different chip selects
25 Also CS1 and CS2 has -A and -B signals. Why they have that is unclear to me.
27 The chip selects have the following memory range assignments. This region of
28 memory is referred to as "Chip Peripheral SS FPB0" and is 168MB big.
30 Chip Select Physical address base
31 CS0 GPIO134 0x1a800000-0x1b000000 (8MB)
32 CS1 GPIO39 (A) / GPIO123 (B) 0x1b000000-0x1b800000 (8MB)
33 CS2 GPIO40 (A) / GPIO124 (B) 0x1b800000-0x1c000000 (8MB)
34 CS3 GPIO133 0x1d000000-0x25000000 (128 MB)
35 CS4 GPIO132 0x1c800000-0x1d000000 (8MB)
36 CS5 GPIO131 0x1c000000-0x1c800000 (8MB)
38 The APQ8060 Qualcomm Application Processor User Guide, 80-N7150-14 Rev. A,
44 this is something just used on the FAST chip selects and that the SLOW
45 chip selects are understood fully. There is also a "byte device enable"
50 together, or if some chip selects are hardwired to be FAST and others are SLOW
58 - Bjorn Andersson <andersson@kernel.org>
63 - qcom,apq8060-ebi2
64 - qcom,msm8660-ebi2
68 - description: EBI2 config region
69 - description: XMEM config region
71 reg-names:
73 - const: ebi2
74 - const: xmem
80 - description: EBI_2X clock
81 - description: EBI clock
83 clock-names:
85 - const: ebi2x
86 - const: ebi2
88 '#address-cells':
91 '#size-cells':
95 - compatible
96 - reg
97 - reg-names
98 - ranges
99 - clocks
100 - clock-names
101 - '#address-cells'
102 - '#size-cells'
105 "^.*@[0-5],[0-9a-f]+$":
112 # SLOW chip selects
113 qcom,xmem-recovery-cycles:
117 is de-asserted, in order to avoid contention on the data bus.
124 qcom,xmem-write-hold-cycles:
134 qcom,xmem-write-delta-cycles:
142 qcom,xmem-read-delta-cycles:
150 qcom,xmem-write-wait-cycles:
157 qcom,xmem-read-wait-cycles:
165 # FAST chip selects
166 qcom,xmem-address-hold-enable:
173 qcom,xmem-adv-to-oe-recovery-cycles:
181 qcom,xmem-read-hold-cycles:
191 - reg
196 - |
197 #include <dt-bindings/clock/qcom,gcc-msm8660.h>
198 #include <dt-bindings/interrupt-controller/irq.h>
199 #include <dt-bindings/gpio/gpio.h>
201 external-bus@1a100000 {
202 compatible = "qcom,msm8660-ebi2";
204 reg-names = "ebi2", "xmem";
213 clock-names = "ebi2x", "ebi2";
215 #address-cells = <2>;
216 #size-cells = <1>;
222 interrupts-extended = <&pm8058_gpio 7 IRQ_TYPE_EDGE_FALLING>,
224 reset-gpios = <&tlmm 30 GPIO_ACTIVE_LOW>;
226 phy-mode = "mii";
227 reg-io-width = <2>;
228 smsc,force-external-phy;
229 smsc,irq-push-pull;
232 qcom,xmem-recovery-cycles = <0>;
233 qcom,xmem-write-hold-cycles = <3>;
234 qcom,xmem-write-delta-cycles = <31>;
235 qcom,xmem-read-delta-cycles = <28>;
236 qcom,xmem-write-wait-cycles = <9>;
237 qcom,xmem-read-wait-cycles = <9>;