Lines Matching +full:read +full:- +full:to +full:- +full:read
3 Contact: linux-scsi@vger.kernel.org
5 This file contains the auto-hibernate idle timer setting of a
6 UFS host controller. A value of '0' means auto-hibernate is not
11 10-bit values with a power-of-ten multiplier which allows a
12 maximum value of 102300000. Refer to the UFS Host Controller
23 The file is read only.
33 The file is read only.
43 The file is read only.
54 The file is read only.
64 The file is read only.
75 The file is read only.
86 The file is read only.
93 descriptor could be read after partial initialization phase
98 The file is read only.
109 The file is read only.
119 The file is read only.
129 The file is read only.
140 The file is read only.
151 The file is read only.
161 The file is read only.
171 The file is read only.
182 The file is read only.
192 The file is read only.
203 The file is read only.
214 The file is read only.
225 The file is read only.
235 The file is read only.
245 The file is read only.
255 The file is read only.
266 The file is read only.
273 written during the pre-soldering phase of the PSA flow.
278 The file is read only.
289 The file is read only.
301 The file is read only.
307 Description: This file shows the MIPI M-PHY version number in BCD format.
312 The file is read only.
319 Description: This file shows the total memory quantity available to
320 the user to configure the device logical units. This is one
325 The file is read only.
336 The file is read only.
346 The file is read only.
356 The file is read only.
367 The file is read only.
373 Description: This file shows the optimal read block size. This is one
378 The file is read only.
389 The file is read only.
395 Description: This file shows the maximum data-in buffer size. This
400 The file is read only.
406 Description: This file shows the maximum data-out buffer size. This
411 The file is read only.
422 The file is read only.
433 The file is read only.
439 Description: This file shows support for out-of-order data transfer.
444 The file is read only.
455 The file is read only.
465 The file is read only.
472 the device to handle system data by the tagging mechanism.
477 The file is read only.
488 The file is read only.
499 The file is read only.
507 enhanced type 1-4). This is one of the UFS geometry
511 The file is read only.
519 enhanced type 1-4). This is one of the UFS geometry
523 The file is read only.
535 The file is read only.
546 The file is read only.
557 The file is read only.
565 active ICC levels from 0 to 15. This is one of the UFS
569 The file is read only.
580 The file is read only.
589 The file is read only.
598 The file is read only.
608 The file is read only.
618 The file is read only.
628 The file is read only.
637 The file is read only.
646 The file is read only.
655 The file is read only.
664 The file is read only.
674 The file is read only.
684 The file is read only.
694 The file is read only.
703 The file is read only.
712 The file is read only.
721 The file is read only.
730 The file is read only.
739 The file is read only.
749 The file is read only.
759 The file is read only.
770 The file is read only.
780 The file is read only.
790 The file is read only.
800 The file is read only.
807 operation related to real time clock. The full information
810 The file is read only.
820 The file is read only.
831 The file is read only.
841 The file is read only.
851 The file is read only.
861 The file is read only.
871 The file is read only.
881 The file is read only.
891 The file is read only.
898 requested with a READY TO TRANSFER UPIU. The full information
901 The file is read only.
911 The file is read only.
919 UFS specifications 2.1. The file is read only.
927 read-write persistent attribute and is equal to two after device
928 manufacturing. It shall not be set to a value greater than
932 The file is read write.
942 The file is read only.
952 The file is read only.
962 The file is read only.
971 The file is read only.
977 Description: This file shows the amount of data that the host plans to
978 load to all logical units in pre-soldering state.
982 The file is read only.
989 to be removed from the physical memory resources pool of
993 The file is read only.
1000 Description: This entry could be used to set or show the UFS device
1009 2 UFS device will be moved to sleep, UIC link will
1011 3 UFS device will be moved to sleep, UIC link will
1017 6 UFS device will be moved to deep sleep, UIC link
1030 The file is read only.
1039 The file is read only.
1045 Description: This entry could be used to set or show the UFS device
1054 2 UFS device will be moved to sleep, UIC link will
1056 3 UFS device will be moved to sleep, UIC link will
1062 6 UFS device will be moved to deep sleep, UIC link
1075 The file is read only.
1084 The file is read only.
1091 and it can be used to start/stop the monitor. When the monitor
1098 Description: This file tells the monitor to focus on requests transferring
1107 sent from device to host after monitor gets started.
1109 The file is read only.
1116 sending data from device to host after monitor gets started.
1118 The file is read only.
1124 Description: This file shows how many read requests have been sent after
1127 The file is read only.
1134 read requests after monitor gets started.
1136 The file is read only.
1143 read requests after monitor gets started.
1145 The file is read only.
1152 read requests after monitor gets started.
1154 The file is read only.
1161 read requests sent after monitor gets started.
1163 The file is read only.
1170 from host to device after monitor gets started.
1172 The file is read only.
1179 sending data from host to device after monitor gets started.
1181 The file is read only.
1190 The file is read only.
1199 The file is read only.
1208 The file is read only.
1217 The file is read only.
1226 The file is read only.
1235 The file is read only.
1243 The file is read only.
1251 The file is read only.
1259 The file is read only.
1267 The file is read only.
1275 The file is read only.
1281 Description: This entry shows if preserve user-space was configured
1283 The file is read only.
1291 The file is read only.
1300 The file is read only.
1306 Description: This entry shows the total user-space decrease in shared
1311 The file is read only.
1320 The file is read only.
1329 The file is read only.
1344 The file is read only.
1359 The file is read only.
1372 The file is read only.
1385 The file is read only.
1394 0 Device is not allowed to flush the
1396 1 Device is allowed to flush the
1400 The file is read only.
1409 The file is read only.
1417 The file is read only.
1434 The file is read only.
1444 01h 0% - 10% WriteBooster Buffer life time used
1446 0Ah 90% - 100% WriteBooster Buffer life time used
1449 The file is read only.
1455 0400h corresponds to 4GB.
1457 The file is read only.
1463 Description: This node is used to set or display whether UFS WriteBooster is
1464 enabled. Echo 0 to this file to disable UFS WriteBooster or 1 to
1465 enable it. The WriteBooster is enabled after power-on/reset,
1474 Contact: Jinyoung Choi <j-young.choi@samsung.com>
1476 and it can be used to enable or disable the flushing.
1488 If avail_wb_buff < wb_flush_threshold, it indicates that WriteBooster buffer needs to
1496 host-device pair. i.e. the capabilities which are enabled in the
1513 The file is read only.
1526 The file is read only.
1534 UFS RTC. If set to 0, this will disable UFS RTC periodic update.
1541 Symbol - VER. This file shows the UFSHCD version.
1543 The file is read only.
1550 Symbol - HCPID. This file shows the UFSHCD product id.
1552 The file is read only.
1559 Symbol - HCMID. This file shows the UFSHCD manufacturer id.
1560 The Manufacturer ID is defined by JEDEC in JEDEC-JEP106.
1561 The file is read only.
1573 The file is read only.
1581 And it can be used to enable/disable the clock scaling by writing
1582 1 or 0 to this attribute.
1584 The attribute is read/write.
1592 And it can be used to enable/disable the clock gating by writing
1593 1 or 0 to this attribute.
1595 The attribute is read/write.
1603 before the UFS driver starts to perform clock gating. This can
1606 The attribute is read/write.
1613 This attribute is applicable to ufs devices compliant to the
1617 time this variable is reset. Writing a 0 value to this
1620 application should read the device_lvl_exception_id attribute to
1623 The attribute is read/write.
1634 implementation. Refer to the device manufacturer datasheet for
1638 The attribute is read only.
1666 decrease Recommend to decrease the buffer size
1667 increase Recommend to increase the buffer size
1670 The file is read only.
1687 The file is read only.
1725 The attribute is read only.
1732 The host sets the size to be defragmented by an HID
1735 The attribute is read/write.
1752 The attribute is read only.
1770 The attribute is read only.