Lines Matching +full:level +full:- +full:high
3 Contact: linux-iio@vger.kernel.org
11 Contact: linux-iio@vger.kernel.org
16 MTCLKA-MTCLKB:
20 MTCLKC-MTCLKD:
26 Contact: linux-iio@vger.kernel.org
33 Contact: linux-iio@vger.kernel.org
39 Contact: linux-iio@vger.kernel.org
41 If the counter device supports compare registers -- registers
42 used to compare counter channels against a particular count --
47 Contact: linux-iio@vger.kernel.org
53 Contact: linux-iio@vger.kernel.org
60 Contact: linux-iio@vger.kernel.org
67 Contact: linux-iio@vger.kernel.org
86 non-recycle:
88 underflow takes place. The counter is re-enabled when a
92 modulo-n:
104 goes high and remains high until a new preset value is
107 hardware retriggerable one-shot:
108 The output signal is initially high. The output signal
111 go high and remain high until the next trigger. A
114 the one-shot pulse.
117 The output signal is initially high. When the counter
119 clock pulse. The output signal then goes high again, the
124 The output signal is initially high.
138 the count expires, the output goes high again and the
143 The output signal is initially high. When the count
145 then go high again. The counting sequence is "triggered"
149 The output signal is initially high. Counting is started
152 go high again. A trigger results in loading the counter
161 Contact: linux-iio@vger.kernel.org
169 Contact: linux-iio@vger.kernel.org
171 Read-only attribute that indicates the count direction of Count
182 Contact: linux-iio@vger.kernel.org
196 Contact: linux-iio@vger.kernel.org
198 Read-only attribute that indicates whether excessive noise is
203 Contact: linux-iio@vger.kernel.org
215 pulse-direction:
217 The input level of signal B determines direction.
250 Contact: linux-iio@vger.kernel.org
252 Read-only attribute that indicates the device-specific name of
258 Contact: linux-iio@vger.kernel.org
267 Contact: linux-iio@vger.kernel.org
269 If the counter device supports preset registers -- registers
270 used to load counter channels to a set count upon device-defined
271 preset operation trigger events -- the preset count for channel
276 Contact: linux-iio@vger.kernel.org
283 Contact: linux-iio@vger.kernel.org
292 Pulse-Direction count function mode, this Signal is
296 Low state transitions to high state.
299 High state transitions to low state.
306 Contact: linux-iio@vger.kernel.org
333 Contact: linux-iio@vger.kernel.org
335 Read-only attribute that indicates the component ID of the
340 Contact: linux-iio@vger.kernel.org
349 Contact: linux-iio@vger.kernel.org
353 rounded-up to a power of 2.
357 Contact: linux-iio@vger.kernel.org
359 Read-only attribute that indicates the device-specific name of
365 Contact: linux-iio@vger.kernel.org
367 Read-only attribute that indicates the total number of Counts
372 Contact: linux-iio@vger.kernel.org
374 Read-only attribute that indicates the total number of Signals
379 Contact: linux-iio@vger.kernel.org
381 Read-only attribute that indicates whether a differential
389 Contact: linux-iio@vger.kernel.org
397 Contact: linux-iio@vger.kernel.org
404 Contact: linux-iio@vger.kernel.org
406 Active level of index input Signal Y; irrelevant in
407 non-synchronous load mode.
412 Contact: linux-iio@vger.kernel.org
419 Contact: linux-iio@vger.kernel.org
421 Active level of Signal Y. The following polarity values are
425 Signal high state considered active level (rising edge).
428 Signal low state considered active level (falling edge).
432 Contact: linux-iio@vger.kernel.org
434 Read-only attribute that indicates the device-specific name of
440 Contact: linux-iio@vger.kernel.org
442 Signal level state of Signal Y. The following signal level
446 Low level state.
448 high:
449 High level state.
453 Contact: linux-iio@vger.kernel.org
456 non-synchronous or synchronous load mode. Synchronous load mode
457 cannot be selected in non-quadrature (Pulse-Direction) clock
460 non-synchronous:
461 A logic low level is the active level at this index
463 is performed directly on the active level of the index
468 quadrature clock mode. The active level is configured
471 quadrature clock on the active level of the index input.
475 Contact: linux-iio@vger.kernel.org
477 Read-only attribute that indicates the signal Y frequency, in Hz.