Lines Matching +full:external +full:- +full:falling

3 Contact:	linux-iio@vger.kernel.org
11 Contact:	linux-iio@vger.kernel.org
13 		Selects the external clock pin for phase counting mode of
16 		MTCLKA-MTCLKB:
17 			MTCLKA and MTCLKB pins are selected for the external
20 		MTCLKC-MTCLKD:
21 			MTCLKC and MTCLKD pins are selected for the external
26 Contact:	linux-iio@vger.kernel.org
33 Contact:	linux-iio@vger.kernel.org
39 Contact:	linux-iio@vger.kernel.org
45 Contact:	linux-iio@vger.kernel.org
52 Contact:	linux-iio@vger.kernel.org
59 Contact:	linux-iio@vger.kernel.org
78 		non-recycle:
80 			underflow takes place. The counter is re-enabled when a
84 		modulo-n:
99 		hardware retriggerable one-shot:
106 			the one-shot pulse.
153 Contact:	linux-iio@vger.kernel.org
161 Contact:	linux-iio@vger.kernel.org
163 		Read-only attribute that indicates the count direction of Count
174 Contact:	linux-iio@vger.kernel.org
188 Contact:	linux-iio@vger.kernel.org
190 		Read-only attribute that indicates whether excessive noise is
195 Contact:	linux-iio@vger.kernel.org
207 		pulse-direction:
214 			is backward, falling edges on quadrature pair signal A
221 			is backward, falling edges on quadrature pair signal B
242 Contact:	linux-iio@vger.kernel.org
244 		Read-only attribute that indicates the device-specific name of
250 Contact:	linux-iio@vger.kernel.org
259 Contact:	linux-iio@vger.kernel.org
261 		If the counter device supports preset registers -- registers
262 		used to load counter channels to a set count upon device-defined
263 		preset operation trigger events -- the preset count for channel
268 Contact:	linux-iio@vger.kernel.org
275 Contact:	linux-iio@vger.kernel.org
284 			Pulse-Direction count function mode, this Signal is
290 		falling edge:
298 Contact:	linux-iio@vger.kernel.org
324 Contact:	linux-iio@vger.kernel.org
326 		Read-only attribute that indicates the component ID of the
331 Contact:	linux-iio@vger.kernel.org
340 Contact:	linux-iio@vger.kernel.org
344 		rounded-up to a power of 2.
348 Contact:	linux-iio@vger.kernel.org
350 		Read-only attribute that indicates the device-specific name of
356 Contact:	linux-iio@vger.kernel.org
358 		Read-only attribute that indicates the total number of Counts
363 Contact:	linux-iio@vger.kernel.org
365 		Read-only attribute that indicates the total number of Signals
370 Contact:	linux-iio@vger.kernel.org
372 		Read-only attribute that indicates whether a differential
380 Contact:	linux-iio@vger.kernel.org
388 Contact:	linux-iio@vger.kernel.org
395 Contact:	linux-iio@vger.kernel.org
398 		non-synchronous load mode.
403 Contact:	linux-iio@vger.kernel.org
410 Contact:	linux-iio@vger.kernel.org
419 			Signal low state considered active level (falling edge).
423 Contact:	linux-iio@vger.kernel.org
425 		Read-only attribute that indicates the device-specific name of
431 Contact:	linux-iio@vger.kernel.org
444 Contact:	linux-iio@vger.kernel.org
447 		non-synchronous or synchronous load mode. Synchronous load mode
448 		cannot be selected in non-quadrature (Pulse-Direction) clock
451 		non-synchronous:
466 Contact:	linux-iio@vger.kernel.org
468 		Read-only attribute that indicates the signal Y frequency, in Hz.