net: dsa: add GRO support via gro_cells

gro_cells lib is used by different encapsulating netdevices, such as
geneve, macsec, vxlan etc. to speed up decapsulated traffic processing.
CPU tag is a sort

net: dsa: add GRO support via gro_cells

gro_cells lib is used by different encapsulating netdevices, such as
geneve, macsec, vxlan etc. to speed up decapsulated traffic processing.
CPU tag is a sort of "encapsulation", and we can use the same mechs to
greatly improve overall DSA performance.
skbs are passed to the GRO layer after removing CPU tags, so we don't
need any new packet offload types as it was firstly proposed by me in
the first GRO-over-DSA variant [1].

The size of struct gro_cells is sizeof(void *), so hot struct
dsa_slave_priv becomes only 4/8 bytes bigger, and all critical fields
remain in one 32-byte cacheline.
The other positive side effect is that drivers for network devices
that can be shipped as CPU ports of DSA-driven switches can now use
napi_gro_frags() to pass skbs to kernel. Packets built that way are
completely non-linear and are likely being dropped without GRO.

This was tested on to-be-mainlined-soon Ethernet driver that uses
napi_gro_frags(), and the overall performance was on par with the
variant from [1], sometimes even better due to minimal overhead.
net.core.gro_normal_batch tuning may help to push it to the limit
on particular setups and platforms.

iperf3 IPoE VLAN NAT TCP forwarding (port1.218 -> port0) setup
on 1.2 GHz MIPS board:

5.7-rc2 baseline:

[ID] Interval Transfer Bitrate Retr
[ 5] 0.00-120.01 sec 9.00 GBytes 644 Mbits/sec 413 sender
[ 5] 0.00-120.00 sec 8.99 GBytes 644 Mbits/sec receiver

Iface RX packets TX packets
eth0 7097731 7097702
port0 426050 6671829
port1 6671681 425862
port1.218 6671677 425851

With this patch:

[ID] Interval Transfer Bitrate Retr
[ 5] 0.00-120.01 sec 12.2 GBytes 870 Mbits/sec 122 sender
[ 5] 0.00-120.00 sec 12.2 GBytes 870 Mbits/sec receiver

Iface RX packets TX packets
eth0 9474792 9474777
port0 455200 353288
port1 9019592 455035
port1.218 353144 455024

v2:
- Add some performance examples in the commit message;
- No functional changes.

[1] https://lore.kernel.org/netdev/20191230143028.27313-1-alobakin@dlink.ru/

Signed-off-by: Alexander Lobakin <bloodyreaper@yandex.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

Merge branch 'for-5.7/appleir' into for-linus

- small code cleanups in hid-appleir from Lucas Tanure

Merge branch 'x86/kdump' into locking/kcsan, to resolve conflicts

Conflicts:
arch/x86/purgatory/Makefile

Signed-off-by: Ingo Molnar <mingo@kernel.org>

Merge drm/drm-next into drm-intel-next-queued

Some DSI and VBT pending patches from Hans will apply
cleanly and with less ugly conflicts if they are rebuilt
on top of other patches that recently lan

Merge drm/drm-next into drm-intel-next-queued

Some DSI and VBT pending patches from Hans will apply
cleanly and with less ugly conflicts if they are rebuilt
on top of other patches that recently landed on drm-next.

Reference: https://patchwork.freedesktop.org/series/70952/
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com

show more ...

Merge tag 'v5.6-rc3' into sched/core, to pick up fixes and dependent patches

Signed-off-by: Ingo Molnar <mingo@kernel.org>

Merge drm-intel-next-queued into gvt-next

Backmerge to pull in
https://patchwork.freedesktop.org/patch/353621/?series=73544&rev=1

Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

Merge v5.6-rc2 into drm-misc-next

Lyude needs some patches in 5.6-rc2 and we didn't bring drm-misc-next
forward yet, so it looks like a good occasion.

Signed-off-by: Maxime Ripard <maxime@cerno.tec

Merge v5.6-rc2 into drm-misc-next

Lyude needs some patches in 5.6-rc2 and we didn't bring drm-misc-next
forward yet, so it looks like a good occasion.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>

show more ...

Merge remote-tracking branch 'net-next/master' into mac80211-next

Merging to get the mac80211 updates that have since propagated
into net-next.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Merge tag 'v5.5-rc4' into locking/kcsan, to resolve conflicts

Conflicts:
init/main.c
lib/Kconfig.debug

Signed-off-by: Ingo Molnar <mingo@kernel.org>

Merge v5.6-rc1 into drm-misc-fixes

We're based on v5.6, need v5.6-rc1 at least. :)

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

Merge branch 'linus' into perf/urgent, to synchronize with upstream

Signed-off-by: Ingo Molnar <mingo@kernel.org>

Merge branch 'next' into for-linus

Prepare input updates for 5.6 merge window.

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next

Pull networking updates from David Miller:

1) Add WireGuard

2) Add HE and TWT support to ath11k driver, from John Crispin.

3

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next

Pull networking updates from David Miller:

1) Add WireGuard

2) Add HE and TWT support to ath11k driver, from John Crispin.

3) Add ESP in TCP encapsulation support, from Sabrina Dubroca.

4) Add variable window congestion control to TIPC, from Jon Maloy.

5) Add BCM84881 PHY driver, from Russell King.

6) Start adding netlink support for ethtool operations, from Michal
Kubecek.

7) Add XDP drop and TX action support to ena driver, from Sameeh
Jubran.

8) Add new ipv4 route notifications so that mlxsw driver does not have
to handle identical routes itself. From Ido Schimmel.

9) Add BPF dynamic program extensions, from Alexei Starovoitov.

10) Support RX and TX timestamping in igc, from Vinicius Costa Gomes.

11) Add support for macsec HW offloading, from Antoine Tenart.

12) Add initial support for MPTCP protocol, from Christoph Paasch,
Matthieu Baerts, Florian Westphal, Peter Krystad, and many others.

13) Add Octeontx2 PF support, from Sunil Goutham, Geetha sowjanya, Linu
Cherian, and others.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1469 commits)
net: phy: add default ARCH_BCM_IPROC for MDIO_BCM_IPROC
udp: segment looped gso packets correctly
netem: change mailing list
qed: FW 8.42.2.0 debug features
qed: rt init valid initialization changed
qed: Debug feature: ilt and mdump
qed: FW 8.42.2.0 Add fw overlay feature
qed: FW 8.42.2.0 HSI changes
qed: FW 8.42.2.0 iscsi/fcoe changes
qed: Add abstraction for different hsi values per chip
qed: FW 8.42.2.0 Additional ll2 type
qed: Use dmae to write to widebus registers in fw_funcs
qed: FW 8.42.2.0 Parser offsets modified
qed: FW 8.42.2.0 Queue Manager changes
qed: FW 8.42.2.0 Expose new registers and change windows
qed: FW 8.42.2.0 Internal ram offsets modifications
MAINTAINERS: Add entry for Marvell OcteonTX2 Physical Function driver
Documentation: net: octeontx2: Add RVU HW and drivers overview
octeontx2-pf: ethtool RSS config support
octeontx2-pf: Add basic ethtool support
...

show more ...

Merge tag 'v5.5-rc5' into next

Sync up with mainline to get SPI "delay" API changes.

Merge drm/drm-next into drm-misc-next

Requested, and we need v5.5-rc1 backported as our current branch is still based on v5.4.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

Merge branch 'add-dsa-switch-support-for-ar9331'

Oleksij Rempel says:

====================
add dsa switch support for ar9331

changes v6:
- remove ag71xx changes from this patch set. It needs more

Merge branch 'add-dsa-switch-support-for-ar9331'

Oleksij Rempel says:

====================
add dsa switch support for ar9331

changes v6:
- remove ag71xx changes from this patch set. It needs more work.
- ar9331: fix register definition and add ASCII art switch documentation.

changes v6:
- rebase against net-next

changes v5:
- remote support for port5. The effort of using this port is
questionable. Currently, it is better to not use it at all, then
adding buggy support.
- remove port enable call back. There is nothing what we actually need
to enable.
- rebase it against v5.5-rc1

changes v4:
- ag71xx: ag71xx_mac_validate fix always false comparison (&& -> ||)
- tag_ar9331: use skb_pull_rcsum() instead of skb_pull().
- tag_ar9331: drop skb_set_mac_header()

changes v3:
- ag71xx: ag71xx_mac_config: ignore MLO_AN_INBAND mode. It is not
supported by HW and SW.
- ag71xx: ag71xx_mac_validate: return all supported bits on
PHY_INTERFACE_MODE_NA

changes v2:
- move Atheros AR9331 TAG format to separate patch
- use netdev_warn_once in the tag driver to reduce potential message spam
- typo fixes
- reorder tag driver alphabetically
- configure switch to maximal frame size
- use mdiobus_read/write
- fail if mdio sub node is not found
- add comment for post reset state
- remove deprecated comment about device id
- remove phy-handle option for node with fixed-link
- ag71xx: set 1G support only for GMII mode

This patch series provides dsa switch support for Atheros ar9331 WiSoC.
As side effect ag71xx needed to be ported to phylink to make the switch
driver (as well phylink based) work properly.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: dsa: add support for Atheros AR9331 TAG format

Add support for tag format used in Atheros AR9331 built-in switch.

Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lun

net: dsa: add support for Atheros AR9331 TAG format

Add support for tag format used in Atheros AR9331 built-in switch.

Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

Merge drm/drm-next into drm-intel-next-queued

Sync up with v5.5-rc1 to get the updated lock_release() API among other
things. Fix the conflict reported by Stephen Rothwell [1].

[1] http://lore.kern

Merge drm/drm-next into drm-intel-next-queued

Sync up with v5.5-rc1 to get the updated lock_release() API among other
things. Fix the conflict reported by Stephen Rothwell [1].

[1] http://lore.kernel.org/r/20191210093957.5120f717@canb.auug.org.au

Signed-off-by: Jani Nikula <jani.nikula@intel.com>

show more ...

Merge mainline/master into arm/fixes

This brings in the mainline tree right after armsoc contents was merged
this release cycle, so that we can re-run savedefconfig, etc.

Signed-off-by: Olof Johans

Merge mainline/master into arm/fixes

This brings in the mainline tree right after armsoc contents was merged
this release cycle, so that we can re-run savedefconfig, etc.

Signed-off-by: Olof Johansson <olof@lixom.net>

show more ...

Merge remote-tracking branch 'torvalds/master' into perf/core

To pick up BPF changes we'll need.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next

Pull networking updates from David Miller:
"Another merge window, another pull full of stuff:

1) Support alternative names fo

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next

Pull networking updates from David Miller:
"Another merge window, another pull full of stuff:

1) Support alternative names for network devices, from Jiri Pirko.

2) Introduce per-netns netdev notifiers, also from Jiri Pirko.

3) Support MSG_PEEK in vsock/virtio, from Matias Ezequiel Vara
Larsen.

4) Allow compiling out the TLS TOE code, from Jakub Kicinski.

5) Add several new tracepoints to the kTLS code, also from Jakub.

6) Support set channels ethtool callback in ena driver, from Sameeh
Jubran.

7) New SCTP events SCTP_ADDR_ADDED, SCTP_ADDR_REMOVED,
SCTP_ADDR_MADE_PRIM, and SCTP_SEND_FAILED_EVENT. From Xin Long.

8) Add XDP support to mvneta driver, from Lorenzo Bianconi.

9) Lots of netfilter hw offload fixes, cleanups and enhancements,
from Pablo Neira Ayuso.

10) PTP support for aquantia chips, from Egor Pomozov.

11) Add UDP segmentation offload support to igb, ixgbe, and i40e. From
Josh Hunt.

12) Add smart nagle to tipc, from Jon Maloy.

13) Support L2 field rewrite by TC offloads in bnxt_en, from Venkat
Duvvuru.

14) Add a flow mask cache to OVS, from Tonghao Zhang.

15) Add XDP support to ice driver, from Maciej Fijalkowski.

16) Add AF_XDP support to ice driver, from Krzysztof Kazimierczak.

17) Support UDP GSO offload in atlantic driver, from Igor Russkikh.

18) Support it in stmmac driver too, from Jose Abreu.

19) Support TIPC encryption and auth, from Tuong Lien.

20) Introduce BPF trampolines, from Alexei Starovoitov.

21) Make page_pool API more numa friendly, from Saeed Mahameed.

22) Introduce route hints to ipv4 and ipv6, from Paolo Abeni.

23) Add UDP segmentation offload to cxgb4, Rahul Lakkireddy"

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1857 commits)
libbpf: Fix usage of u32 in userspace code
mm: Implement no-MMU variant of vmalloc_user_node_flags
slip: Fix use-after-free Read in slip_open
net: dsa: sja1105: fix sja1105_parse_rgmii_delays()
macvlan: schedule bc_work even if error
enetc: add support Credit Based Shaper(CBS) for hardware offload
net: phy: add helpers phy_(un)lock_mdio_bus
mdio_bus: don't use managed reset-controller
ax88179_178a: add ethtool_op_get_ts_info()
mlxsw: spectrum_router: Fix use of uninitialized adjacency index
mlxsw: spectrum_router: After underlay moves, demote conflicting tunnels
bpf: Simplify __bpf_arch_text_poke poke type handling
bpf: Introduce BPF_TRACE_x helper for the tracing tests
bpf: Add bpf_jit_blinding_enabled for !CONFIG_BPF_JIT
bpf, testing: Add various tail call test cases
bpf, x86: Emit patchable direct jump as tail call
bpf: Constant map key tracking for prog array pokes
bpf: Add poke dependency tracking for prog array maps
bpf: Add initial poke descriptor table for jit images
bpf: Move owner type, jited info into array auxiliary data
...

show more ...

Merge branch 'next' into for-linus

Prepare input updates for 5.5 merge window.

Merge tag 'v5.4-rc8' into WIP.x86/mm, to pick up fixes

Signed-off-by: Ingo Molnar <mingo@kernel.org>

Merge branch 'DSA-driver-for-Vitesse-Felix-switch'

Vladimir Oltean says:

====================
DSA driver for Vitesse Felix switch

This series builds upon the previous "Accomodate DSA front-end int

Merge branch 'DSA-driver-for-Vitesse-Felix-switch'

Vladimir Oltean says:

====================
DSA driver for Vitesse Felix switch

This series builds upon the previous "Accomodate DSA front-end into
Ocelot" topic and does the following:

- Reworks the Ocelot (VSC7514) driver to support one more switching core
(VSC9959), used in NPI mode. Some code which was thought to be
SoC-specific (ocelot_board.c) wasn't, and vice versa, so it is being
accordingly moved.
- Exports ocelot driver structures and functions to include/soc/mscc.
- Adds a DSA ocelot front-end for VSC9959, which is a PCI device and
uses the exported ocelot functionality for hardware configuration.
- Adds a tagger driver for the Vitesse injection/extraction DSA headers.
This is known to be compatible with at least Ocelot and Felix.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: dsa: ocelot: add tagger for Ocelot/Felix switches

While it is entirely possible that this tagger format is in fact more
generic than just these 2 switch families, I don't have that knowledge.
T

net: dsa: ocelot: add tagger for Ocelot/Felix switches

While it is entirely possible that this tagger format is in fact more
generic than just these 2 switch families, I don't have that knowledge.
The Seville switch in NXP T1040 has a similar frame format, but there
are enough differences (e.g. DEST field starts at bit 57 instead of 56)
that calling this file tag_vitesse.c is a bit of a stretch at the
moment. The frame format has been listed in a comment so that people who
add support for further Vitesse switches can rework this tagger while
keeping compatibility with Felix.

The "ocelot" name was chosen instead of "felix" because even the Ocelot
switch can act as a DSA device when it is used in NPI mode, and the Felix
tagger format is almost identical. Currently it is only used for the
Felix switch embedded in the NXP LS1028A chip.

The ABI for this tagger should be considered "not stable" at the moment.
The DSA tag is always placed before the Ethernet header and therefore,
we are using the long prefix for RX tags to avoid putting the DSA master
port in promiscuous mode. Once there will be an API in DSA for drivers
to request DSA masters to be in promiscuous mode unconditionally, we
will switch to the "no prefix" extraction frame header, which will save
16 padding bytes for each RX frame.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...