e1000e: correct maximum frequency adjustment values

The e1000e driver supports hardware with a variety of different clock
speeds, and thus a variety of different increment values used for
programmin

e1000e: correct maximum frequency adjustment values

The e1000e driver supports hardware with a variety of different clock
speeds, and thus a variety of different increment values used for
programming its PTP hardware clock.

The values currently programmed in e1000e_ptp_init are incorrect. In
particular, only two maximum adjustments are used: 24000000 - 1, and
600000000 - 1. These were originally intended to be used with the 96 MHz
clock and the 25 MHz clock.

Both of these values are actually slightly too high. For the 96 MHz clock,
the actual maximum value that can safely be programmed is 23,999,938. For
the 25 MHz clock, the maximum value is 599,999,904.

Worse, several devices use a 24 MHz clock or a 38.4 MHz clock. These parts
are incorrectly assigned one of either the 24million or 600million values.
For the 24 MHz clock, this is not a significant issue: its current
increment value can support an adjustment up to 7billion in the positive
direction. However, the 38.4 KHz clock uses an increment value which can
only support up to 230,769,157 before it starts overflowing.

To understand where these values come from, consider that frequency
adjustments have the form of:

new_incval = base_incval + (base_incval * adjustment) / (unit of adjustment)

The maximum adjustment is reported in terms of parts per billion:
new_incval = base_incval + (base_incval * adjustment) / 1 billion

The largest possible adjustment is thus given by the following:
max_incval = base_incval + (base_incval * max_adj) / 1 billion

Re-arranging to solve for max_adj:
max_adj = (max_incval - base_incval) * 1 billion / base_incval

We also need to ensure that negative adjustments cannot underflow. This can
be achieved simply by ensuring max_adj is always less than 1 billion.

Introduce new macros in e1000.h codifying the maximum adjustment in PPB for
each frequency given its associated increment values. Also clarify where
these values come from by commenting about the above equations.

Replace the switch statement in e1000e_ptp_init with one which mirrors the
increment value switch statement from e1000e_get_base_timinica. For each
device, assign the appropriate maximum adjustment based on its frequency.
Some parts can have one of two frequency modes as determined by
E1000_TSYNCRXCTL_SYSCFI.

Since the new flow directly matches the assignments in
e1000e_get_base_timinca, and uses well defined macro names, it is much
easier to verify that the resulting maximum adjustments are correct. It
also avoids difficult to parse construction such as the "hw->mac.type <
e1000_phc_lpt", and the use of fallthrough which was especially confusing
when combined with a conditional block.

Note that I believe the current increment value configuration used for
24MHz clocks is sub-par, as it leaves at least 3 extra bits available in
the INCVALUE register. However, fixing that requires more careful review of
the clock rate and associated values.

Reported-by: Trey Harrison <harrisondigitalmedia@gmail.com>
Fixes: 68fe1d5da548 ("e1000e: Add Support for 38.4MHZ frequency")
Fixes: d89777bf0e42 ("e1000e: add support for IEEE-1588 PTP")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

show more ...

Merge branch 'next' into for-linus

Prepare input updates for 6.3 merge window.

Merge drm/drm-next into drm-misc-next

Backmerging into drm-misc-next to get DRM accelerator infrastructure,
which is required by ipuv driver.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>

Merge tag 'v6.2-rc3' into next

Merge with mainline to bring in timer_shutdown_sync() API.

Merge drm/drm-next into drm-intel-next

Sync up with v6.2-rc1.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>

Merge drm/drm-next into drm-intel-gt-next

Sync after v6.2-rc1 landed in drm-next.

We need to get some dependencies in place before we can merge
the fixes series from Gwan-gyeong and Chris.

Referen

Merge drm/drm-next into drm-intel-gt-next

Sync after v6.2-rc1 landed in drm-next.

We need to get some dependencies in place before we can merge
the fixes series from Gwan-gyeong and Chris.

References: https://lore.kernel.org/all/Y6x5JCDnh2rvh4lA@intel.com/
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

show more ...

Merge tag 'v6.2-rc1' into media_tree

Linux 6.2-rc1

* tag 'v6.2-rc1': (14398 commits)
Linux 6.2-rc1
treewide: Convert del_timer*() to timer_shutdown*()
pstore: Properly assign mem_type propert

Merge tag 'v6.2-rc1' into media_tree

Linux 6.2-rc1

* tag 'v6.2-rc1': (14398 commits)
Linux 6.2-rc1
treewide: Convert del_timer*() to timer_shutdown*()
pstore: Properly assign mem_type property
pstore: Make sure CONFIG_PSTORE_PMSG selects CONFIG_RT_MUTEXES
cfi: Fix CFI failure with KASAN
perf python: Fix splitting CC into compiler and options
afs: Stop implementing ->writepage()
afs: remove afs_cache_netfs and afs_zap_permits() declarations
afs: remove variable nr_servers
afs: Fix lost servers_outstanding count
ALSA: usb-audio: Add new quirk FIXED_RATE for JBL Quantum810 Wireless
ALSA: azt3328: Remove the unused function snd_azf3328_codec_outl()
gcov: add support for checksum field
test_maple_tree: add test for mas_spanning_rebalance() on insufficient data
maple_tree: fix mas_spanning_rebalance() on insufficient data
hugetlb: really allocate vma lock for all sharable vmas
kmsan: export kmsan_handle_urb
kmsan: include linux/vmalloc.h
mm/mempolicy: fix memory leak in set_mempolicy_home_node system call
mm, mremap: fix mremap() expanding vma with addr inside vma
...

show more ...

Merge drm/drm-fixes into drm-misc-fixes

Let's start the fixes cycle.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>

Merge remote-tracking branch 'torvalds/master' into perf/core

To resolve a trivial merge conflict with c302378bc157f6a7 ("libbpf:
Hashmap interface update to allow both long and void* keys/values"),

Merge remote-tracking branch 'torvalds/master' into perf/core

To resolve a trivial merge conflict with c302378bc157f6a7 ("libbpf:
Hashmap interface update to allow both long and void* keys/values"),
where a function present upstream was removed in the perf tools
development tree.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

show more ...

Merge branch 'main' into zstd-linus

Merge tag 'net-next-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next

Pull networking updates from Paolo Abeni:
"Core:

- Allow live renaming when an interface is up

- Ad

Merge tag 'net-next-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next

Pull networking updates from Paolo Abeni:
"Core:

- Allow live renaming when an interface is up

- Add retpoline wrappers for tc, improving considerably the
performances of complex queue discipline configurations

- Add inet drop monitor support

- A few GRO performance improvements

- Add infrastructure for atomic dev stats, addressing long standing
data races

- De-duplicate common code between OVS and conntrack offloading
infrastructure

- A bunch of UBSAN_BOUNDS/FORTIFY_SOURCE improvements

- Netfilter: introduce packet parser for tunneled packets

- Replace IPVS timer-based estimators with kthreads to scale up the
workload with the number of available CPUs

- Add the helper support for connection-tracking OVS offload

BPF:

- Support for user defined BPF objects: the use case is to allocate
own objects, build own object hierarchies and use the building
blocks to build own data structures flexibly, for example, linked
lists in BPF

- Make cgroup local storage available to non-cgroup attached BPF
programs

- Avoid unnecessary deadlock detection and failures wrt BPF task
storage helpers

- A relevant bunch of BPF verifier fixes and improvements

- Veristat tool improvements to support custom filtering, sorting,
and replay of results

- Add LLVM disassembler as default library for dumping JITed code

- Lots of new BPF documentation for various BPF maps

- Add bpf_rcu_read_{,un}lock() support for sleepable programs

- Add RCU grace period chaining to BPF to wait for the completion of
access from both sleepable and non-sleepable BPF programs

- Add support storing struct task_struct objects as kptrs in maps

- Improve helper UAPI by explicitly defining BPF_FUNC_xxx integer
values

- Add libbpf *_opts API-variants for bpf_*_get_fd_by_id() functions

Protocols:

- TCP: implement Protective Load Balancing across switch links

- TCP: allow dynamically disabling TCP-MD5 static key, reverting back
to fast[er]-path

- UDP: Introduce optional per-netns hash lookup table

- IPv6: simplify and cleanup sockets disposal

- Netlink: support different type policies for each generic netlink
operation

- MPTCP: add MSG_FASTOPEN and FastOpen listener side support

- MPTCP: add netlink notification support for listener sockets events

- SCTP: add VRF support, allowing sctp sockets binding to VRF devices

- Add bridging MAC Authentication Bypass (MAB) support

- Extensions for Ethernet VPN bridging implementation to better
support multicast scenarios

- More work for Wi-Fi 7 support, comprising conversion of all the
existing drivers to internal TX queue usage

- IPSec: introduce a new offload type (packet offload) allowing
complete header processing and crypto offloading

- IPSec: extended ack support for more descriptive XFRM error
reporting

- RXRPC: increase SACK table size and move processing into a
per-local endpoint kernel thread, reducing considerably the
required locking

- IEEE 802154: synchronous send frame and extended filtering support,
initial support for scanning available 15.4 networks

- Tun: bump the link speed from 10Mbps to 10Gbps

- Tun/VirtioNet: implement UDP segmentation offload support

Driver API:

- PHY/SFP: improve power level switching between standard level 1 and
the higher power levels

- New API for netdev <-> devlink_port linkage

- PTP: convert existing drivers to new frequency adjustment
implementation

- DSA: add support for rx offloading

- Autoload DSA tagging driver when dynamically changing protocol

- Add new PCP and APPTRUST attributes to Data Center Bridging

- Add configuration support for 800Gbps link speed

- Add devlink port function attribute to enable/disable RoCE and
migratable

- Extend devlink-rate to support strict prioriry and weighted fair
queuing

- Add devlink support to directly reading from region memory

- New device tree helper to fetch MAC address from nvmem

- New big TCP helper to simplify temporary header stripping

New hardware / drivers:

- Ethernet:
- Marvel Octeon CNF95N and CN10KB Ethernet Switches
- Marvel Prestera AC5X Ethernet Switch
- WangXun 10 Gigabit NIC
- Motorcomm yt8521 Gigabit Ethernet
- Microchip ksz9563 Gigabit Ethernet Switch
- Microsoft Azure Network Adapter
- Linux Automation 10Base-T1L adapter

- PHY:
- Aquantia AQR112 and AQR412
- Motorcomm YT8531S

- PTP:
- Orolia ART-CARD

- WiFi:
- MediaTek Wi-Fi 7 (802.11be) devices
- RealTek rtw8821cu, rtw8822bu, rtw8822cu and rtw8723du USB
devices

- Bluetooth:
- Broadcom BCM4377/4378/4387 Bluetooth chipsets
- Realtek RTL8852BE and RTL8723DS
- Cypress.CYW4373A0 WiFi + Bluetooth combo device

Drivers:

- CAN:
- gs_usb: bus error reporting support
- kvaser_usb: listen only and bus error reporting support

- Ethernet NICs:
- Intel (100G):
- extend action skbedit to RX queue mapping
- implement devlink-rate support
- support direct read from memory
- nVidia/Mellanox (mlx5):
- SW steering improvements, increasing rules update rate
- Support for enhanced events compression
- extend H/W offload packet manipulation capabilities
- implement IPSec packet offload mode
- nVidia/Mellanox (mlx4):
- better big TCP support
- Netronome Ethernet NICs (nfp):
- IPsec offload support
- add support for multicast filter
- Broadcom:
- RSS and PTP support improvements
- AMD/SolarFlare:
- netlink extened ack improvements
- add basic flower matches to offload, and related stats
- Virtual NICs:
- ibmvnic: introduce affinity hint support
- small / embedded:
- FreeScale fec: add initial XDP support
- Marvel mv643xx_eth: support MII/GMII/RGMII modes for Kirkwood
- TI am65-cpsw: add suspend/resume support
- Mediatek MT7986: add RX wireless wthernet dispatch support
- Realtek 8169: enable GRO software interrupt coalescing per
default

- Ethernet high-speed switches:
- Microchip (sparx5):
- add support for Sparx5 TC/flower H/W offload via VCAP
- Mellanox mlxsw:
- add 802.1X and MAC Authentication Bypass offload support
- add ip6gre support

- Embedded Ethernet switches:
- Mediatek (mtk_eth_soc):
- improve PCS implementation, add DSA untag support
- enable flow offload support
- Renesas:
- add rswitch R-Car Gen4 gPTP support
- Microchip (lan966x):
- add full XDP support
- add TC H/W offload via VCAP
- enable PTP on bridge interfaces
- Microchip (ksz8):
- add MTU support for KSZ8 series

- Qualcomm 802.11ax WiFi (ath11k):
- support configuring channel dwell time during scan

- MediaTek WiFi (mt76):
- enable Wireless Ethernet Dispatch (WED) offload support
- add ack signal support
- enable coredump support
- remain_on_channel support

- Intel WiFi (iwlwifi):
- enable Wi-Fi 7 Extremely High Throughput (EHT) PHY capabilities
- 320 MHz channels support

- RealTek WiFi (rtw89):
- new dynamic header firmware format support
- wake-over-WLAN support"

* tag 'net-next-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2002 commits)
ipvs: fix type warning in do_div() on 32 bit
net: lan966x: Remove a useless test in lan966x_ptp_add_trap()
net: ipa: add IPA v4.7 support
dt-bindings: net: qcom,ipa: Add SM6350 compatible
bnxt: Use generic HBH removal helper in tx path
IPv6/GRO: generic helper to remove temporary HBH/jumbo header in driver
selftests: forwarding: Add bridge MDB test
selftests: forwarding: Rename bridge_mdb test
bridge: mcast: Support replacement of MDB port group entries
bridge: mcast: Allow user space to specify MDB entry routing protocol
bridge: mcast: Allow user space to add (*, G) with a source list and filter mode
bridge: mcast: Add support for (*, G) with a source list and filter mode
bridge: mcast: Avoid arming group timer when (S, G) corresponds to a source
bridge: mcast: Add a flag for user installed source entries
bridge: mcast: Expose __br_multicast_del_group_src()
bridge: mcast: Expose br_multicast_new_group_src()
bridge: mcast: Add a centralized error path
bridge: mcast: Place netlink policy before validation functions
bridge: mcast: Split (*, G) and (S, G) addition into different functions
bridge: mcast: Do not derive entry type from its filter mode
...

show more ...

Merge branch '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2022-11-02 (e1000e, e1000, igc)

This ser

Merge branch '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2022-11-02 (e1000e, e1000, igc)

This series contains updates to e1000e, e1000, and igc drivers.

For e1000e, Sasha adds a new board type to help distinguish platforms and
adds device id support for upcoming platforms. He also adds trace points
for CSME flows to aid in debugging.

Ani removes unnecessary kmap_atomic call for e1000 and e1000e.

Muhammad sets speed based transmit offsets for launchtime functionality to
reduce latency for igc.

* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
igc: Correct the launchtime offset
e1000: Remove unnecessary use of kmap_atomic()
e1000e: Remove unnecessary use of kmap_atomic()
e1000e: Add e1000e trace module
e1000e: Add support for the next LOM generation
e1000e: Separate MTP board type from ADP
====================

Link: https://lore.kernel.org/r/20221102203957.2944396-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

e1000e: Separate MTP board type from ADP

We have the same LAN controller on different PCH's. Separate MTP board
type from an ADP which will allow for specific fixes to be applied for MTP
platforms.

e1000e: Separate MTP board type from ADP

We have the same LAN controller on different PCH's. Separate MTP board
type from an ADP which will allow for specific fixes to be applied for MTP
platforms.

Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

show more ...

Merge branch 'main' into zstd-next

Merge branch 'next' into for-linus

Prepare input updates for 6.1 merge window.

Merge drm/drm-next into drm-intel-gt-next

Daniele needs 84d4333c1e28 ("misc/mei: Add NULL check to component match
callback functions") in order to merge the DG2 HuC patches.

Signed-off-by: Tvrtko

Merge drm/drm-next into drm-intel-gt-next

Daniele needs 84d4333c1e28 ("misc/mei: Add NULL check to component match
callback functions") in order to merge the DG2 HuC patches.

Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

show more ...

Merge branch 'for-6.1/nvdimm' into libnvdimm-for-next

Add v6.1 content on top of some straggling updates that missed v6.0.

Merge branch 'mlx5-vfio' into mlx5-next

Merge net/mlx5 dependencies for device DMA logging.

Signed-off-by: Leon Romanovsky <leonro@nvidia.com>

Merge branch 'for-6.0/dax' into libnvdimm-fixes

Pick up another "Soft Reservation" fix for v6.0-final on top of some
straggling nvdimm fixes that missed v5.19.

Merge tag 'v6.0-rc6' into locking/core, to refresh the branch

Signed-off-by: Ingo Molnar <mingo@kernel.org>

Merge drm/drm-next into drm-misc-next

We need 6.0-rc1 to merge the backlight rework PR.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>

Merge branch 'am5748-fix' into fixes

Merge branch 'linus' into x86/mm, to refresh the branch

This branch is ~14k commits behind upstream, and has an old merge base
from early into the merge window, refresh it to v6.0-rc3+fixes before
q

Merge branch 'linus' into x86/mm, to refresh the branch

This branch is ~14k commits behind upstream, and has an old merge base
from early into the merge window, refresh it to v6.0-rc3+fixes before
queueing up new commits.

Signed-off-by: Ingo Molnar <mingo@kernel.org>

show more ...

Merge branch 'sched/warnings' into sched/core, to pick up WARN_ON_ONCE() conversion commit

Merge in the BUG_ON() => WARN_ON_ONCE() conversion commit.

Signed-off-by: Ingo Molnar <mingo@kernel.org>

Merge drm/drm-next into drm-intel-next

Sync drm-intel-next with v6.0-rc as well as recent drm-intel-gt-next.

Since drm-next does not have commit f0c70d41e4e8 ("drm/i915/guc: remove
runtime info pri

Merge drm/drm-next into drm-intel-next

Sync drm-intel-next with v6.0-rc as well as recent drm-intel-gt-next.

Since drm-next does not have commit f0c70d41e4e8 ("drm/i915/guc: remove
runtime info printing from time stamp logging") yet, only
drm-intel-gt-next, will need to do that as part of the merge here to
build.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>

show more ...