Merge branch 'for-5.11/elecom' into for-linus

- support for EX-G M-XGL20DLBK device, from YOSHIOKA Takuma

Merge branch 'next' into for-linus

Prepare input updates for 5.11 merge window.

Merge remote-tracking branch 'spi/for-5.10' into spi-linus

Merge remote-tracking branch 'asoc/for-5.10' into asoc-linus

mtd: rawnand: rockchip: NFC driver for RK3308, RK2928 and others

This driver supports Rockchip NFC (NAND Flash Controller) found on RK3308,
RK2928, RKPX30, RV1108 and other SOCs. The driver has been

mtd: rawnand: rockchip: NFC driver for RK3308, RK2928 and others

This driver supports Rockchip NFC (NAND Flash Controller) found on RK3308,
RK2928, RKPX30, RV1108 and other SOCs. The driver has been tested using
8-bit NAND interface on the ARM based RK3308 platform.

Support Rockchip SoCs and NFC versions:
- PX30 and RK3326(NFCv900).
ECC: 16/40/60/70 bits/1KB.
CLOCK: ahb and nfc.
- RK3308 and RV1108(NFCv800).
ECC: 16 bits/1KB.
CLOCK: ahb and nfc.
- RK3036 and RK3128(NFCv622).
ECC: 16/24/40/60 bits/1KB.
CLOCK: ahb and nfc.
- RK3066, RK3188 and RK2928(NFCv600).
ECC: 16/24/40/60 bits/1KB.
CLOCK: ahb.

Supported features:
- Read full page data by DMA.
- Support HW ECC(one step is 1KB).
- Support 2 - 32K page size.
- Support 8 CS(depend on SoCs)

Limitations:
- No support for the ecc step size is 512.
- Untested on some SoCs.
- No support for subpages.
- No support for the builtin randomizer.
- The original bad block mask is not supported. It is recommended to use
the BBT(bad block table).

Suggested-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201210002134.5686-3-yifeng.zhao@rock-chips.com

show more ...

mtd: rawnand: Add NAND controller support on Intel LGM SoC

This patch adds the new IP of Nand Flash Controller(NFC) support
on Intel's Lightning Mountain(LGM) SoC.

DMA is used for burst data transf

mtd: rawnand: Add NAND controller support on Intel LGM SoC

This patch adds the new IP of Nand Flash Controller(NFC) support
on Intel's Lightning Mountain(LGM) SoC.

DMA is used for burst data transfer operation, also DMA HW supports
aligned 32bit memory address and aligned data access by default.
DMA burst of 8 supported. Data register used to support the read/write
operation from/to device.

Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201110012333.18647-3-vadivel.muruganx.ramuthevar@linux.intel.com

show more ...

mtd: rawnand: mxc: Remove platform data support

i.MX is a devicetree-only platform now and the existing platform data
support in this driver was only useful for old non-devicetree platforms.

Get ri

mtd: rawnand: mxc: Remove platform data support

i.MX is a devicetree-only platform now and the existing platform data
support in this driver was only useful for old non-devicetree platforms.

Get rid of the platform data support since it is no longer used.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201110121908.19400-1-festevam@gmail.com

show more ...

mtd: nand: ecc-hamming: Let the software Hamming ECC engine be unselected

There is no reason to always embed the software Hamming ECC engine
implementation. By default it is (with raw NAND), but we

mtd: nand: ecc-hamming: Let the software Hamming ECC engine be unselected

There is no reason to always embed the software Hamming ECC engine
implementation. By default it is (with raw NAND), but we can let the
user decide.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-19-miquel.raynal@bootlin.com

show more ...

mtd: nand: ecc-hamming: Move Hamming code to the generic NAND layer

Hamming ECC code might be later re-used by the SPI NAND layer.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: htt

mtd: nand: ecc-hamming: Move Hamming code to the generic NAND layer

Hamming ECC code might be later re-used by the SPI NAND layer.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-12-miquel.raynal@bootlin.com

show more ...

Merge branches 'for-next/kvm-build-fix', 'for-next/va-refactor', 'for-next/lto', 'for-next/mem-hotplug', 'for-next/cppc-ffh', 'for-next/pad-image-header', 'for-next/zone-dma-default-32-bit', 'for-nex

Merge branches 'for-next/kvm-build-fix', 'for-next/va-refactor', 'for-next/lto', 'for-next/mem-hotplug', 'for-next/cppc-ffh', 'for-next/pad-image-header', 'for-next/zone-dma-default-32-bit', 'for-next/signal-tag-bits' and 'for-next/cmdline-extended' into for-next/core

* for-next/kvm-build-fix:
: Fix KVM build issues with 64K pages
KVM: arm64: Fix build error in user_mem_abort()

* for-next/va-refactor:
: VA layout changes
arm64: mm: don't assume struct page is always 64 bytes
Documentation/arm64: fix RST layout of memory.rst
arm64: mm: tidy up top of kernel VA space
arm64: mm: make vmemmap region a projection of the linear region
arm64: mm: extend linear region for 52-bit VA configurations

* for-next/lto:
: Upgrade READ_ONCE() to RCpc acquire on arm64 with LTO
arm64: lto: Strengthen READ_ONCE() to acquire when CONFIG_LTO=y
arm64: alternatives: Remove READ_ONCE() usage during patch operation
arm64: cpufeatures: Add capability for LDAPR instruction
arm64: alternatives: Split up alternative.h
arm64: uaccess: move uao_* alternatives to asm-uaccess.h

* for-next/mem-hotplug:
: Memory hotplug improvements
arm64/mm/hotplug: Ensure early memory sections are all online
arm64/mm/hotplug: Enable MEM_OFFLINE event handling
arm64/mm/hotplug: Register boot memory hot remove notifier earlier
arm64: mm: account for hotplug memory when randomizing the linear region

* for-next/cppc-ffh:
: Add CPPC FFH support using arm64 AMU counters
arm64: abort counter_read_on_cpu() when irqs_disabled()
arm64: implement CPPC FFH support using AMUs
arm64: split counter validation function
arm64: wrap and generalise counter read functions

* for-next/pad-image-header:
: Pad Image header to 64KB and unmap it
arm64: head: tidy up the Image header definition
arm64/head: avoid symbol names pointing into first 64 KB of kernel image
arm64: omit [_text, _stext) from permanent kernel mapping

* for-next/zone-dma-default-32-bit:
: Default to 32-bit wide ZONE_DMA (previously reduced to 1GB for RPi4)
of: unittest: Fix build on architectures without CONFIG_OF_ADDRESS
mm: Remove examples from enum zone_type comment
arm64: mm: Set ZONE_DMA size based on early IORT scan
arm64: mm: Set ZONE_DMA size based on devicetree's dma-ranges
of: unittest: Add test for of_dma_get_max_cpu_address()
of/address: Introduce of_dma_get_max_cpu_address()
arm64: mm: Move zone_dma_bits initialization into zone_sizes_init()
arm64: mm: Move reserve_crashkernel() into mem_init()
arm64: Force NO_BLOCK_MAPPINGS if crashkernel reservation is required
arm64: Ignore any DMA offsets in the max_zone_phys() calculation

* for-next/signal-tag-bits:
: Expose the FAR_EL1 tag bits in siginfo
arm64: expose FAR_EL1 tag bits in siginfo
signal: define the SA_EXPOSE_TAGBITS bit in sa_flags
signal: define the SA_UNSUPPORTED bit in sa_flags
arch: provide better documentation for the arch-specific SA_* flags
signal: clear non-uapi flag bits when passing/returning sa_flags
arch: move SA_* definitions to generic headers
parisc: start using signal-defs.h
parisc: Drop parisc special case for __sighandler_t

* for-next/cmdline-extended:
: Add support for CONFIG_CMDLINE_EXTENDED
arm64: Extend the kernel command line from the bootloader
arm64: kaslr: Refactor early init command line parsing

show more ...

mtd: nand: ecc-bch: Move BCH code to the generic NAND layer

BCH ECC code might be later re-used by the SPI NAND layer.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.ke

mtd: nand: ecc-bch: Move BCH code to the generic NAND layer

BCH ECC code might be later re-used by the SPI NAND layer.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-3-miquel.raynal@bootlin.com

show more ...

Merge remote-tracking branch 'origin/master' into perf/core

Further perf/core patches will depend on:

d3f7b1bb2040 ("mm/gup: fix gup_fast with dynamic page table folding")

which is already in Li

Merge remote-tracking branch 'origin/master' into perf/core

Further perf/core patches will depend on:

d3f7b1bb2040 ("mm/gup: fix gup_fast with dynamic page table folding")

which is already in Linus' tree.

show more ...

Merge tag 'v5.9' into next

Sync up with mainline to bring in the latest DTS files.

Merge branch 'linus' into perf/kprobes

Conflicts:
include/asm-generic/atomic-instrumented.h
kernel/kprobes.c

Use the upstream atomic-instrumented.h checksum, and pick
the kprobes version of kerne

Merge branch 'linus' into perf/kprobes

Conflicts:
include/asm-generic/atomic-instrumented.h
kernel/kprobes.c

Use the upstream atomic-instrumented.h checksum, and pick
the kprobes version of kernel/kprobes.c, which effectively
reverts this upstream workaround:

645f224e7ba2: ("kprobes: Tell lockdep about kprobe nesting")

Since the new code *should* be fine without nesting.

Knock on wood ...

Signed-off-by: Ingo Molnar <mingo@kernel.org>

show more ...

Merge drm/drm-next into drm-intel-next-queued

Catch up with v5.10-rc2 and drm-misc-next.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>

Merge branch 'core/urgent' into core/entry

Pick up the entry fix before further modifications.

Merge drm/drm-next into drm-misc-next

Daniel needs -rc2 in drm-misc-next to merge some patches

Signed-off-by: Maxime Ripard <maxime@cerno.tech>

Merge tag 'v5.10-rc1' into kvmarm-master/next

Linux 5.10-rc1

Signed-off-by: Marc Zyngier <maz@kernel.org>

Merge tag 'drm-intel-fixes-2020-10-29' into gvt-fixes

Backmerge for 5.10-rc1 to apply one extra APL fix.

Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>

Merge tag 'v5.10-rc1' into regulator-5.10

Linux 5.10-rc1

Merge tag 'v5.10-rc1' into spi-5.10

Linux 5.10-rc1

Merge tag 'v5.10-rc1' into asoc-5.10

Linux 5.10-rc1

Merge tag 'mtd/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux

Pull MTD updates from Richard Weinberger:
"NAND core changes:
- Drop useless 'depends on' in Kconfig
- Add

Merge tag 'mtd/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux

Pull MTD updates from Richard Weinberger:
"NAND core changes:
- Drop useless 'depends on' in Kconfig
- Add an extra level in the Kconfig hierarchy
- Trivial spellings
- Dynamic allocation of the interface configurations
- Dropping the default ONFI timing mode
- Various cleanup (types, structures, naming, comments)
- Hide the chip->data_interface indirection
- Add the generic rb-gpios property
- Add the ->choose_interface_config() hook
- Introduce nand_choose_best_sdr_timings()
- Use default values for tPROG_max and tBERS_max
- Avoid redefining tR_max and tCCS_min
- Add a helper to find the closest ONFI mode
- bcm63xx MTD parsers: simplify CFE detection

Raw NAND controller drivers changes:
- fsl-upm: Deprecation of specific DT properties
- fsl_upm: Driver rework and cleanup in favor of ->exec_op()
- Ingenic: Cleanup ARRAY_SIZE() vs sizeof() use
- brcmnand: ECC error handling on EDU transfers
- brcmnand: Don't default to EDU transfers
- qcom: Set BAM mode only if not set already
- qcom: Avoid write to unavailable register
- gpio: Driver rework in favor of ->exec_op()
- tango: ->exec_op() conversion
- mtk: ->exec_op() conversion

Raw NAND chip drivers changes:
- toshiba: Implement ->choose_interface_config() for TH58NVG2S3HBAI4
- toshiba: Implement ->choose_interface_config() for TC58NVG0S3E
- toshiba: Implement ->choose_interface_config() for TC58TEG5DCLTA00
- hynix: Implement ->choose_interface_config() for H27UCG8T2ATR-BC

HyperBus changes:
- DMA support for TI's AM654 HyperBus controller driver.
- HyperBus frontend driver for Renesas RPC-IF driver.

SPI NOR core changes:
- Support for Winbond w25q64jwm flash
- Enable 4K sector support for mx25l12805d

SPI NOR controller drivers changes:
- intel-spi Add Alder Lake-S PCI ID

MTD Core changes:
- mtdoops: Don't run panic write twice
- mtdconcat: Correctly handle panic write
- Use DEFINE_SHOW_ATTRIBUTE"

* tag 'mtd/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (76 commits)
mtd: hyperbus: Fix build failure when only RPCIF_HYPERBUS is enabled
mtd: hyperbus: add Renesas RPC-IF driver
Revert "mtd: spi-nor: Prefer asynchronous probe"
mtd: parsers: bcm63xx: Do not make it modular
mtd: spear_smi: Enable compile testing
mtd: maps: vmu-flash: fix typos for struct memcard
mtd: physmap: Add Baikal-T1 physically mapped ROM support
mtd: maps: vmu-flash: simplify the return expression of probe_maple_vmu
mtd: onenand: simplify the return expression of onenand_transfer_auto_oob
mtd: rawnand: cadence: remove a redundant dev_err call
mtd: rawnand: ams-delta: Fix non-OF build warning
mtd: rawnand: Don't overwrite the error code from nand_set_ecc_soft_ops()
mtd: rawnand: Introduce nand_set_ecc_on_host_ops()
mtd: rawnand: atmel: Check return values for nand_read_data_op
mtd: rawnand: vf610: Remove unused function vf610_nfc_transfer_size()
mtd: rawnand: qcom: Simplify with dev_err_probe()
mtd: rawnand: marvell: Fix and update kerneldoc
mtd: rawnand: marvell: Simplify with dev_err_probe()
mtd: rawnand: gpmi: Simplify with dev_err_probe()
mtd: rawnand: atmel: Simplify with dev_err_probe()
...

show more ...

Merge tag 'nand/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next

NAND core changes:
* Use the new generic ECC object
* Create helpers to set/extract the ECC require

Merge tag 'nand/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next

NAND core changes:
* Use the new generic ECC object
* Create helpers to set/extract the ECC requirements
* Create a helper to extract the ECC configuration
* Add a NAND page I/O request type
* Introduce the ECC engine framework

Raw NAND core changes:
* Don't overwrite the error code from nand_set_ecc_soft_ops()
* Introduce nand_set_ecc_on_host_ops()
* Use the NAND framework user_conf object for ECC flags
* Use the ECC framework user input parsing bits
* Use the ECC framework nand_ecc_is_strong_enough() helper
* Use the ECC framework OOB layouts
* Make use of the ECC framework
* Use nanddev_get/set_ecc_requirements() when relevant
* Use the new ECC engine type enumeration
* Separate the ECC engine type and the ECC byte placement
* Move the nand_ecc_algo enum to the generic NAND layer
* Rename the ECC algorithm enumeration items
* Add a kernel doc to the ECC algorithm enumeration
* DT bindings:
- Document boolean NAND ECC properties
- Document nand-ecc-engine
- Document nand-ecc-placement

Raw NAND drivers changes:
* Ams-Delta: Fix non-OF build warning
* Atmel:
- Check return values for nand_read_data_op
- Simplify with dev_err_probe()
- Get rid of the legacy interface implementation
- Convert the driver to exec_op()
- Use nand_prog_page_end_op()
- Use nand_{write,read}_data_op()
- Drop redundant nand_read_page_op()
- Enable the NFC controller at probe time
- Disable clk on error handling path in probe
* Cadence: remove a redundant dev_err call
* Gpmi:
- Simplify with dev_err_probe()
* Marvell:
- Fix and update kerneldoc
- Simplify with dev_err_probe()
- Fix and update kerneldoc
- Simplify with dev_err_probe()
- Support panic_write for mtdoops
* Onenand:
- Simplify the return expression of onenand_transfer_auto_oob
- Simplify with dev_err_probe()
* Oxnas: cleanup/simplify code
* Pasemi: Make pasemi_device_ready() static
* Qcom: Simplify with dev_err_probe()
* Stm32_fmc2: fix a buffer overflow
* Vf610: Remove unused function vf610_nfc_transfer_size()

SPI-NAND changes:
* Use nanddev_get_ecc_conf() when relevant
* Gigadevice:
- Add support for GD5F4GQ4xC
- Add QE Bit
- Use only one dummy byte in QUADIO
* Macronix:
- Add support for MX31UF1GE4BC
- Add support for MX31LF1GE4BC

show more ...

mtd: rawnand: Make use of the ECC framework

Just enable the ECC framework with raw NAND so that we can drop, one
by one, all the unnecessary/redundant definitions.

Signed-off-by: Miquel Raynal <miq

mtd: rawnand: Make use of the ECC framework

Just enable the ECC framework with raw NAND so that we can drop, one
by one, all the unnecessary/redundant definitions.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200827085208.16276-17-miquel.raynal@bootlin.com

show more ...