Merge tag 'mfd-next-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd

Pull mfd updates from Lee Jones:

- Fix race in device_node_get_regmap() using more extensive locking

- Remove u

Merge tag 'mfd-next-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd

Pull mfd updates from Lee Jones:

- Fix race in device_node_get_regmap() using more extensive locking

- Remove unused platform driver support for syscon

- Allow syscon nodes to be registered without a "syscon" compatible
string

- Make `platform_data` pointer const in struct mfd_cell

- Revert support for multiple AXP PMICs to avoid regressions

- Increase SoundWire attach timeout and use gpiod_set_raw() for GPIO
operation

- Store the result from fault_log() for use by other sub-components

- Fix an invalid regmap-config max_register value

- Add another Gemini Lake ISA bridge PCI device ID

- Use devm_register_power_off_handler() to simplify code

- Add support for QNAP microcontroller units, including LEDs, input,
and hwmon

- Use MFD_CELL macros and remove unused code

- Add support for AAEON UP board FPGA

- Remove unused includes

- Fix various typos and compatibility issues in multiple bindings

- Add new bindings for rk3562 QoS, LED1202, and qcom,tcsr-ipq5424

- Convert several bindings to YAML schema

- Update sprd,sc2731 bindings to reference sprd,sc2731-efuse bindings
directly

- Fix rohm,bd71815 bindings by correcting resistor values and typos

- Documentation improvements:
- Add documentation for LED1202 and qnap-mcu-hwmon
- Adjust the file entry for the qnap-mcu header in MAINTAINERS

* tag 'mfd-next-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (35 commits)
MAINTAINERS: Adjust the file entry for the qnap-mcu header
dt-bindings: mfd: syscon: Fix ti,j784s4-acspcie-proxy-ctrl compatible
dt-bindings: mfd: syscon: Fix al,alpine-sysfabric-service compatible
Revert "mfd: axp20x: Allow multiple regulators"
dt-bindings: mfd: syscon: Add rk3562 QoS register compatible
mfd: syscon: Allow syscon nodes without a "syscon" compatible
mfd: syscon: Remove the platform driver support
mfd: syscon: Fix race in device_node_get_regmap()
dt-bindings: mfd: atmel: Convert to YAML schema
dt-bindings: mfd: atmel,at91sam9260: Convert to YAML schema
dt-bindings: mfd: sprd,sc2731: Reference sprd,sc2731-efuse bindings
mfd: tps65219: Remove unused macros & add regmap.h
mfd: tps65219: Use MFD_CELL macros
leds: Add LED1202 I2C driver
dt-bindings: leds: Add LED1202 LED Controller
Documentation:leds: Add leds-st1202.rst
mfd: Add support for AAEON UP board FPGA
mfd: da9052: Store result from fault_log
mfd: intel_soc_pmic_chtdc_ti: Fix invalid regmap-config max_register value
mfd: cs42l43: Use devres for remove as well
...

show more ...

dt-bindings: leds: Add LED1202 LED Controller

The LED1202 is a 12-channel low quiescent current LED driver with:
* Supply range from 2.6 V to 5 V
* 20 mA current capability per channel
* 1.8 V

dt-bindings: leds: Add LED1202 LED Controller

The LED1202 is a 12-channel low quiescent current LED driver with:
* Supply range from 2.6 V to 5 V
* 20 mA current capability per channel
* 1.8 V compatible I2C control interface
* 8-bit analog dimming individual control
* 12-bit local PWM resolution
* 8 programmable patterns

If the led node is present in the controller then the channel is
set to active.

Signed-off-by: Vicentiu Galanopulo <vicentiu.galanopulo@remote-tech.co.uk>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20241218183401.41687-3-vicentiu.galanopulo@remote-tech.co.uk
Signed-off-by: Lee Jones <lee@kernel.org>

show more ...

dt-bindings: leds: Add LED1202 LED Controller

The LED1202 is a 12-channel low quiescent current LED driver with:
* Supply range from 2.6 V to 5 V
* 20 mA current capability per channel
* 1.8 V

dt-bindings: leds: Add LED1202 LED Controller

The LED1202 is a 12-channel low quiescent current LED driver with:
* Supply range from 2.6 V to 5 V
* 20 mA current capability per channel
* 1.8 V compatible I2C control interface
* 8-bit analog dimming individual control
* 12-bit local PWM resolution
* 8 programmable patterns

If the led node is present in the controller then the channel is
set to active.

Signed-off-by: Vicentiu Galanopulo <vicentiu.galanopulo@remote-tech.co.uk>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20241218182001.41476-3-vicentiu.galanopulo@remote-tech.co.uk
Signed-off-by: Lee Jones <lee@kernel.org>

show more ...