Remove residual blank line at start of Makefile

This is a residual of the $FreeBSD$ removal.

MFC After: 3 days (though I'll just run the command on the branches)
Sponsored by: Netflix

sys: Remove $FreeBSD$: one-line sh pattern

Remove /^\s*#[#!]?\s*\$FreeBSD\$.*$\n/

Move most of the contents of opt_compat.h to opt_global.h.

opt_compat.h is mentioned in nearly 180 files. In-progress network
driver compabibility improvements may add over 100 more so this is
close

Move most of the contents of opt_compat.h to opt_global.h.

opt_compat.h is mentioned in nearly 180 files. In-progress network
driver compabibility improvements may add over 100 more so this is
closer to "just about everywhere" than "only some files" per the
guidance in sys/conf/options.

Keep COMPAT_LINUX32 in opt_compat.h as it is confined to a subset of
sys/compat/linux/*.c. A fake _COMPAT_LINUX option ensure opt_compat.h
is created on all architectures.

Move COMPAT_LINUXKPI to opt_dontuse.h as it is only used to control the
set of compiled files.

Reviewed by: kib, cem, jhb, jtl
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D14941

show more ...

sys/modules: normalize .CURDIR-relative paths to SRCTOP

This simplifies make output/logic

Tested with: `cd sys/modules; make ALL_MODULES=` on amd64
MFC after: 1 month
Sponsored by: Dell EMC Isilon

Merge sync of head

MFhead @ r277403

Reintegrate head: r274132-r277384

Sponsored by: The FreeBSD Foundation

Reintegrate head revisions r273096-r277147

Sponsored by: The FreeBSD Foundation

Re-support CWARNFLAGS, lost when bsd.sys.mk was removed. Also, support
CWARNFALGS.$file centrally so we don't have to have it in all the
places. Remove a few warning flags that are no longer needed.

Re-support CWARNFLAGS, lost when bsd.sys.mk was removed. Also, support
CWARNFALGS.$file centrally so we don't have to have it in all the
places. Remove a few warning flags that are no longer needed.
Also, always use -Wno-unknown-pragma to (hopefully temporarily) work
around #pragma ident in debug.h in the opensolaris code. Remove some
stale warning suppression that's no longer necessary.

show more ...

MFC @ r266724

An SVM update will follow this.

IFC @266473

Merge from head

Bring in the mpr(4) driver for LSI's MPT3 12Gb SAS controllers.

This is derived from the mps(4) driver, but it supports only the 12Gb
IT and IR hardware including the SAS 3004, SAS 3008 and SAS 3108

Bring in the mpr(4) driver for LSI's MPT3 12Gb SAS controllers.

This is derived from the mps(4) driver, but it supports only the 12Gb
IT and IR hardware including the SAS 3004, SAS 3008 and SAS 3108.

Some notes about this driver:
o The 12Gb hardware can do "FastPath" I/O, and that capability is included in
this driver.

o WarpDrive functionality has been removed, since it isn't supported in
the 12Gb driver interface.

o The Scatter/Gather list handling code is significantly different between
the 6Gb and 12Gb hardware. The 12Gb boards support IEEE Scatter/Gather
lists.

Thanks to LSI for developing and testing this driver for FreeBSD.

share/man/man4/mpr.4:
mpr(4) man page.

sys/dev/mpr/*:
mpr(4) driver files.

sys/modules/Makefile,
sys/modules/mpr/Makefile:
Add a module Makefile for the mpr(4) driver.

sys/conf/files:
Add the mpr(4) driver.

sys/amd64/conf/GENERIC,
sys/i386/conf/GENERIC,
sys/mips/conf/OCTEON1,
sys/sparc64/conf/GENERIC:
Add the mpr(4) driver to all config files that currently
have the mps(4) driver.

sys/ia64/conf/GENERIC:
Add the mps(4) and mpr(4) drivers to the ia64 GENERIC
config file.

sys/i386/conf/XEN:
Exclude the mpr module from building here.

Submitted by: Steve McConnell <Stephen.McConnell@lsi.com>
MFC after: 3 days
Tested by: Chris Reeves <chrisr@spectralogic.com>
Sponsored by: LSI, Spectra Logic
Relnotes: LSI 12Gb SAS driver mpr(4) added

show more ...