Remove residual blank line at start of Makefile

This is a residual of the $FreeBSD$ removal.

MFC After: 3 days (though I'll just run the command on the branches)
Sponsored by: Netflix

sys: Remove $FreeBSD$: one-line sh pattern

Remove /^\s*#[#!]?\s*\$FreeBSD\$.*$\n/

sys/modules: normalize .CURDIR-relative paths to SRCTOP

This simplifies make output/logic

Tested with: `cd sys/modules; make ALL_MODULES=` on amd64
MFC after: 1 month
Sponsored by: Dell EMC Isilon

IFC @ r254014

IFC @253398

Merge fresh head.

sync from head

- With the demise of !ATA_CAM, ATA_STATIC_ID is the only ata(4) related
option left but actually consumed by ada(4), so move it to opt_ada.h
and get rid of opt_ata.h.
- Fix stand-alone build of a

- With the demise of !ATA_CAM, ATA_STATIC_ID is the only ata(4) related
option left but actually consumed by ada(4), so move it to opt_ada.h
and get rid of opt_ata.h.
- Fix stand-alone build of atacore(4) by adding opt_cam.h.
- Use __FBSDID.
- Use DEVMETHOD_END.
- Use NULL instead of 0 for pointers.

show more ...

This is the roumored ATA modulerisation works, and it needs a little explanation.

If you just config KERNEL as usual there should be no apparent changes, you'll get all chipset support code compiled

This is the roumored ATA modulerisation works, and it needs a little explanation.

If you just config KERNEL as usual there should be no apparent changes, you'll get all chipset support code compiled in.

However there is now a way to only compile in code for chipsets needed on a pr vendor basis. ATA now has the following "device" entries:

atacore: ATA core functionality, always needed for any ATA setup

atacard: CARDBUS support
atacbus: PC98 cbus support
ataisa: ISA bus support
atapci: PCI bus support only generic chipset support.

ataahci: AHCI support, also pulled in by some vendor modules.

ataacard, ataacerlabs, ataadaptec, ataamd, ataati, atacenatek, atacypress, atacyrix, atahighpoint, ataintel, ataite, atajmicron, atamarvell, atamicron, atanational, atanetcell, atanvidia, atapromise, ataserverworks, atasiliconimage, atasis, atavia; Vendor support, ie atavia for VIA chipsets

atadisk: ATA disk driver
ataraid: ATA softraid driver

atapicd: ATAPI cd/dvd driver
atapifd: ATAPI floppy/flashdisk driver
atapist: ATAPI tape driver

atausb: ATA<>USB bridge
atapicam: ATA<>CAM bridge

This makes it possible to config a kernel with just VIA chipset support by having the following ATA lines in the kernel config file:

device atacore
device atapci
device atavia

And then you need the atadisk, atapicd etc lines in there just as usual.

If you use ATA as modules loaded at boot there is few changes except the rename of the "ata" module to "atacore", things looks just as usual.
However under atapci you now have a whole bunch of vendor specific drivers, that you can kldload individually depending on you needs. Drivers have the same names as used in the kernel config explained above.

show more ...

This is the roumored ATA modulerisation works, and it needs a little explanation.

If you just config KERNEL as usual there should be no apparent changes, you'll get all chipset support code compiled

This is the roumored ATA modulerisation works, and it needs a little explanation.

If you just config KERNEL as usual there should be no apparent changes, you'll get all chipset support code compiled in.

However there is now a way to only compile in code for chipsets needed on a pr vendor basis. ATA now has the following "device" entries:

atacore: ATA core functionality, always needed for any ATA setup

atacard: CARDBUS support
atacbus: PC98 cbus support
ataisa: ISA bus support
atapci: PCI bus support only generic chipset support.

ataahci: AHCI support, also pulled in by some vendor modules.

ataacard, ataacerlabs, ataadaptec, ataamd, ataati, atacenatek, atacypress, atacyrix, atahighpoint, ataintel, ataite, atajmicron, atamarvell, atamicron, atanational, atanetcell, atanvidia, atapromise, ataserverworks, atasiliconimage, atasis, atavia; Vendor support, ie atavia for VIA chipsets

atadisk: ATA disk driver
ataraid: ATA softraid driver

atapicd: ATAPI cd/dvd driver
atapifd: ATAPI floppy/flashdisk driver
atapist: ATAPI tape driver

atausb: ATA<>USB bridge
atapicam: ATA<>CAM bridge

This makes it possible to config a kernel with just VIA chipset support by having the following ATA lines in the kernel config file:

device atacore
device atapci
device atavia

And then you need the atadisk, atapicd etc lines in there just as usual.

If you use ATA as modules loaded at boot there is few changes except the rename of the "ata" module to "atacore", things looks just as usual.
However under atapci you now have a whole bunch of vendor specific drivers, that you can kldload individually depending on you needs. Drivers have the same names as used in the kernel config explained above.

show more ...