sys: Remove $FreeBSD$: two-line .h pattern

Remove /^\s*\*\n \*\s+\$FreeBSD\$$\n/

if_cdce: Add support for setting RX filtering

We can now set promisc and allmulti modes.
Filtering of given multicast addresses is not supported.
Changing the mode is done by sending a command descr

if_cdce: Add support for setting RX filtering

We can now set promisc and allmulti modes.
Filtering of given multicast addresses is not supported.
Changing the mode is done by sending a command described in:
"USB CDC Subclass Specification for Ethernet Devices v1.2, section 6.2.4".
This means that at least in theory this feature should work with all
modems that are using this driver.

This fixes Huawei E3372h-320 running new firmware in "HiLink" mode.
Previously it would reset a few seconds after its mode was changed
with "usb_modeswitch".
Setting RX filter to default value at the end of attach function
fixed that.

Sponsored by: Stormshield
Obtained from: Semihalf
Differential revision: https://reviews.freebsd.org/D31766
MFC after: 2 weeks
Reviewed by: hps

show more ...

Add support for link status, media and VLAN MTU (if supported) to if_cdce...

This makes it more usable in that dhclient will autolaunch from devd
now when cdce devices are plugged in.. It also sets

Add support for link status, media and VLAN MTU (if supported) to if_cdce...

This makes it more usable in that dhclient will autolaunch from devd
now when cdce devices are plugged in.. It also sets the baudrate, but
this isn't exported via tools, and CDCE doesn't have a good way to
specify the media type, so there isn't a good way to tell userland
what the speed is currently...

Reviewed by: hps
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D30625

show more ...

Merge ^/head r325842 through r325998.

spdx: initial adoption of licensing ID tags.

The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensou

spdx: initial adoption of licensing ID tags.

The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.

Special thanks to Wind River for providing access to "The Duke of
Highlander" tool: an older (2014) run over FreeBSD tree was useful as a
starting point.

Initially, only tag files that use BSD 4-Clause "Original" license.

RelNotes: yes
Differential Revision: https://reviews.freebsd.org/D13133

show more ...

Merge sync of head

MFhead @ r277403

Reintegrate head: r274132-r277384

Sponsored by: The FreeBSD Foundation

o Notify USB host about connection when operating in device mode.
Required when communicating to Mac OS X USB host stack.
o Also don't set stall bit to TX pipe in device mode as seems Mac OS X
do

o Notify USB host about connection when operating in device mode.
Required when communicating to Mac OS X USB host stack.
o Also don't set stall bit to TX pipe in device mode as seems Mac OS X
don't clears it as it should.

Discussed with: hselasky@

show more ...

The maximum NCM frame size must be so that it
will generate a short terminated USB transfer if
the maximum NCM frame size is greater than what
the driver can handle.

Reported by: Matthias Benesch
MF

The maximum NCM frame size must be so that it
will generate a short terminated USB transfer if
the maximum NCM frame size is greater than what
the driver can handle.

Reported by: Matthias Benesch
MFC after: 7 days
Approved by: thompsa (mentor)

show more ...

Merge svn+ssh://svn.freebsd.org/base/head@214309

USB network (NCM driver):
- correct the ethernet payload remainder which
must be post-offseted by -14 bytes instead of
0 bytes. This is not very clearly defined in the
NCM specification.
- add develo

USB network (NCM driver):
- correct the ethernet payload remainder which
must be post-offseted by -14 bytes instead of
0 bytes. This is not very clearly defined in the
NCM specification.
- add development feature about limiting the
maximum datagram count in each NCM payload.
- zero-pad alignment data
- add TX-interval tuning sysctl

Approved by: thompsa (mentor)

show more ...

IFH@204581

MFC r197563

Add basic support for USB Network Control Model (NCM) v1.0 to if_cdce.c.

- MFC

Add basic support for USB Network Control Model (NCM) v1.0 to if_cdce.c.

http://www.usb.org/developers/devclass_docs/NCM10.zip

Submitted by: Hans Petter Selasky

Merge from head

Merge r188942 (USB stack switch) from head.

- Merge from HEAD

s/usb2_/usb_/ on all C structs for the USB stack.

- Merge from HEAD

MFp4 //depot/projects/usb@159909

- make usb2_power_mask_t 16-bit
- remove "usb2_config_sub" structure from "usb2_config". To compensate for this
"usb2_config" has a new field called "usb_mode" whi

MFp4 //depot/projects/usb@159909

- make usb2_power_mask_t 16-bit
- remove "usb2_config_sub" structure from "usb2_config". To compensate for this
"usb2_config" has a new field called "usb_mode" which select for which mode
the current xfer entry is active. Options are: a) Device mode only b) Host
mode only (default-by-zero) c) Both modes. This change was scripted using
the following sed script: "s/\.mh\././g".
- the standard packet size table in "usb_transfer.c" is now a function, hence
the code for the function uses less memory than the table itself.

Submitted by: Hans Petter Selasky

show more ...

Update the projects tree to a newer FreeBSD current.

Move the new USB stack into its new home.

- MFC