sys: Automated cleanup of cdefs and other formatting

Apply the following automated changes to try to eliminate
no-longer-needed sys/cdefs.h includes as well as now-empty
blank lines in a row.

Remov

sys: Automated cleanup of cdefs and other formatting

Apply the following automated changes to try to eliminate
no-longer-needed sys/cdefs.h includes as well as now-empty
blank lines in a row.

Remove /^#if.*\n#endif.*\n#include\s+<sys/cdefs.h>.*\n/
Remove /\n+#include\s+<sys/cdefs.h>.*\n+#if.*\n#endif.*\n+/
Remove /\n+#if.*\n#endif.*\n+/
Remove /^#if.*\n#endif.*\n/
Remove /\n+#include\s+<sys/cdefs.h>\n#include\s+<sys/types.h>/
Remove /\n+#include\s+<sys/cdefs.h>\n#include\s+<sys/param.h>/
Remove /\n+#include\s+<sys/cdefs.h>\n#include\s+<sys/capsicum.h>/

Sponsored by: Netflix

show more ...

sys: Remove $FreeBSD$: one-line .c pattern

Remove /^[\s*]*__FBSDID\("\$FreeBSD\$"\);?\s*\n/

spdx: The BSD-2-Clause-FreeBSD identifier is obsolete, drop -FreeBSD

The SPDX folks have obsoleted the BSD-2-Clause-FreeBSD identifier. Catch
up to that fact and revert to their recommended match of

spdx: The BSD-2-Clause-FreeBSD identifier is obsolete, drop -FreeBSD

The SPDX folks have obsoleted the BSD-2-Clause-FreeBSD identifier. Catch
up to that fact and revert to their recommended match of BSD-2-Clause.

Discussed with: pfg
MFC After: 3 days
Sponsored by: Netflix

show more ...

MFHead @348740

Sponsored by: The FreeBSD Foundation

Extract eventfilter declarations to sys/_eventfilter.h

This allows replacing "sys/eventfilter.h" includes with "sys/_eventfilter.h"
in other header files (e.g., sys/{bus,conf,cpu}.h) and reduces hea

Extract eventfilter declarations to sys/_eventfilter.h

This allows replacing "sys/eventfilter.h" includes with "sys/_eventfilter.h"
in other header files (e.g., sys/{bus,conf,cpu}.h) and reduces header
pollution substantially.

EVENTHANDLER_DECLARE and EVENTHANDLER_LIST_DECLAREs were moved out of .c
files into appropriate headers (e.g., sys/proc.h, powernv/opal.h).

As a side effect of reduced header pollution, many .c files and headers no
longer contain needed definitions. The remainder of the patch addresses
adding appropriate includes to fix those files.

LOCK_DEBUG and LOCK_FILE_LINE_ARG are moved to sys/_lock.h, as required by
sys/mutex.h since r326106 (but silently protected by header pollution prior
to this change).

No functional change (intended). Of course, any out of tree modules that
relied on header pollution for sys/eventhandler.h, sys/lock.h, or
sys/mutex.h inclusion need to be fixed. __FreeBSD_version has been bumped.

show more ...

sys/dev: further adoption of SPDX licensing ID tags.

Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error

sys/dev: further adoption of SPDX licensing ID tags.

Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.

The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.

show more ...

Merge head r233826 through r256722.

IFC @256277

Approved by: ken (mentor)

Merge from head

IFC @ r255209

IFC @ r254014

Make r253899 compile.

- Implement iclear methods for QUICC and SAB 82532. With r253161 in place,
this is is crucial at least for the latter.
What happens is that attaching uart(4) to scc(4) causes the SAB 82532 to
"

- Implement iclear methods for QUICC and SAB 82532. With r253161 in place,
this is is crucial at least for the latter.
What happens is that attaching uart(4) to scc(4) causes the SAB 82532 to
"receive" something and trigger a SER_INT_RXREADY interrupt, given that
at least fast/filter interrupts are already enabled. Prior to r253161,
uart_bus_ihand() was set up at this point and handled that condition,
i. e. read the RX FIFO and issued a Receive Message Complete.
Now, uart_bus_ihand() and uart_intr() are setup after attaching uart(4),
leaving the SER_INT_RXREADY interrupt triggered during the latter to
be handled by the iclear method. However, with that method not implement,
this in turn causes SAB 82532 to not issue any further SER_INT_RXREADY
interrupts until the RX FIFO is full again. Thus, 15 received bytes go
to nowhere, given that "the other half" of the RX FIFO is used for status
information. Hence, implementing sab82532_bfe_iclear() fixes things again.
Potentially, the same problem exists for QUICC.
- Remove unnecessary __RMAN_RESOURCE_VISIBLE.
- Remove a superfluous header.
- Use KOBJMETHOD_END.
- Mark unused arguments as such.
- Remove variables unused after initialization.

Reviewed by: marcel (earlier version)

show more ...

Support for Freescale QUad Integrated Communications Controller.

The QUICC engine is found on various Freescale parts including MPC85xx, and
provides multiple generic time-division serial channel re

Support for Freescale QUad Integrated Communications Controller.

The QUICC engine is found on various Freescale parts including MPC85xx, and
provides multiple generic time-division serial channel resources, which are in
turn muxed/demuxed by the Serial Communications Controller (SCC).

Along with core QUICC/SCC functionality a uart(4)-compliant device driver is
provided which allows for serial ports over QUICC/SCC.

Approved by: cognet (mentor)
Obtained from: Juniper
MFp4: e500

show more ...

Support for Freescale QUad Integrated Communications Controller.

The QUICC engine is found on various Freescale parts including MPC85xx, and
provides multiple generic time-division serial channel re

Support for Freescale QUad Integrated Communications Controller.

The QUICC engine is found on various Freescale parts including MPC85xx, and
provides multiple generic time-division serial channel resources, which are in
turn muxed/demuxed by the Serial Communications Controller (SCC).

Along with core QUICC/SCC functionality a uart(4)-compliant device driver is
provided which allows for serial ports over QUICC/SCC.

Approved by: cognet (mentor)
Obtained from: Juniper
MFp4: e500

show more ...