sys: Remove $FreeBSD$: one-line .c pattern

Remove /^[\s*]*__FBSDID\("\$FreeBSD\$"\);?\s*\n/

spdx: The BSD-2-Clause-FreeBSD identifier is obsolete, drop -FreeBSD

The SPDX folks have obsoleted the BSD-2-Clause-FreeBSD identifier. Catch
up to that fact and revert to their recommended match of

spdx: The BSD-2-Clause-FreeBSD identifier is obsolete, drop -FreeBSD

The SPDX folks have obsoleted the BSD-2-Clause-FreeBSD identifier. Catch
up to that fact and revert to their recommended match of BSD-2-Clause.

Discussed with: pfg
MFC After: 3 days
Sponsored by: Netflix

show more ...

mps/mpr: Add missing newlines in error messages.

MFC after: 1 week

mps: clean up empty lines in .c and .h files

sys/dev: further adoption of SPDX licensing ID tags.

Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error

sys/dev: further adoption of SPDX licensing ID tags.

Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.

The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.

show more ...

MFhead@r322451

Merge ^/head r321383 through r322397.

Changes to make mps(4) and mpr(4) handle reinit with reallocation.

When the mps(4) and mpr(4) drivers need to reinitialize the
firmware, they sometimes need to reallocate all of the memory
allocated

Changes to make mps(4) and mpr(4) handle reinit with reallocation.

When the mps(4) and mpr(4) drivers need to reinitialize the
firmware, they sometimes need to reallocate all of the memory
allocated by the driver. The reallocation happens whenever the IOC
Facts change. That should only happen after a firmware upgrade.

If the reinitialization happens as a result of a timed out command
sent to the card, the command that timed out and triggered the
reinit may have been freed if iocfacts_allocate() reallocated all
memory. If the caller attempts to access the command after that,
the kernel will panic because the caller will be dereferencing
freed memory.

The solution is to set a flag in the softc when we reallocate,
and avoid dereferencing the command strucure if we've reallocated.

The changes are largely the same in both drivers, since mpr(4) is a
derivative of mps(4).

o In iocfacts_allocate(), if the IOC Facts have changed and we
need to reallocate, set the REALLOCATED flag in the softc.

o Change wait_command() to take a struct mps_command ** instead of
a struct mps_command *. This allows us to NULL out the caller's
command pointer if we have to reinit the controller and the data
structures get reallocated. (The REALLOCATED flag will be set
in the softc if that has happened.)

o In every place that calls wait_command(), make sure we handle
the case where the command is NULL after the call.

o The mpr(4) driver has mpr_request_polled() which can also
reinitialize the card. Also check for reallocation there.

Reviewed by: scottl, slm
MFC after: 1 week
Sponsored by: Spectra Logic

show more ...

- No log bit in IOCStatus and endian-safe changes.

Use MPI2_IOCSTATUS_MASK when checking IOCStatus to mask off the log bit, and
make a few more things endian-safe.

- Fix possible use of invalid poi

- No log bit in IOCStatus and endian-safe changes.

Use MPI2_IOCSTATUS_MASK when checking IOCStatus to mask off the log bit, and
make a few more things endian-safe.

- Fix possible use of invalid pointer.

It was possible to use an invalid pointer to get the target ID value. To fix
this, initialize a local Target ID variable to an invalid value and change that
variable to a valid value only if the pointer to the Target ID is not NULL.

- No need to set the MPSSAS_SHUTDOWN flag because it's never used.

- done_ccb pointer can be used if it is NULL.

To prevent this, move check for done_ccb == NULL to before done_ccb is used in
mpssas_stop_unit_done().

- Disks can go missing until a reboot is done in some cases.

This is due to the DevHandle not being released, which causes the Firmware to
not allow that disk to be re-added.

Reviewed by: ken
Approved by: re (gjb), ken, scottl, ambrisko (mentors)
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D6872

show more ...

sys/dev: minor spelling fixes.

Most affect comments, very few have user-visible effects.

Merge from head

Sponsored by: Gandi.net

Finish merging from head, messed up in previous attempt

Merge from HEAD

Catch up with head, primarily for the 1.14.4.0 firmware.

Merge ^/head r286422 through r286684.

Remove mps_request_polled(), it's redundant to mps_wait_command()

Obtained from: Netflix, Inc.

Merge sync of head

MFH: r278968-r280640

Sponsored by: The FreeBSD Foundation

Merge from head

Merge r278538 through r279514.

Merge ^/head r279163 through r279308.

- Updated all files with 2015 Avago copyright, and updated LSI's copyright
dates.

- Changed all of the PCI device strings from LSI to Avago Technologies (LSI).

- Added a sysctl variable to contro

- Updated all files with 2015 Avago copyright, and updated LSI's copyright
dates.

- Changed all of the PCI device strings from LSI to Avago Technologies (LSI).

- Added a sysctl variable to control how StartStopUnit behavior works. User can
select to spin down disks based on if disk is SSD or HDD.

- Inquiry data is required to tell if a disk will support SSU at shutdown or
not. Due to the addition of mpssas_async, which gets Advanced Info but not
Inquiry data, the setting of supports_SSU was moved to the
mpssas_scsiio_complete function, which snoops for any Inquiry commands. And,
since disks are shutdown as a target and not a LUN, this process was
simplified by basing it on targets and not LUNs.

- Added a sysctl variable that sets the amount of time to retry after sending a
failed SATA ID command. This helps with some bad disks and large disks that
require a lot of time to spin up. Part of this change was to add a callout to
handle timeouts with the SATA ID command. The callout function is called
mpssas_ata_id_timeout(). (Fixes PR 191348)

- Changed the way resets work by allowing I/O to continue to devices that are
not currently under a reset condition. This uses devq's instead of simq's and
makes use of the MPSSAS_TARGET_INRESET flag. This change also adds a function
called mpssas_prepare_tm().

- Some changes were made to reduce code duplication when getting a SAS address
for a SATA disk.

- Fixed some formatting and whitespace.

- Bump version of mps driver to 20.00.00.00-fbsd

PR: 191348
Reviewed by: ken, scottl
Approved by: ken, scottl
MFC after: 2 weeks

show more ...

Merge head r233826 through r256722.

IFC @256277

Approved by: ken (mentor)

Merge from head