sys: Automated cleanup of cdefs and other formatting

Apply the following automated changes to try to eliminate
no-longer-needed sys/cdefs.h includes as well as now-empty
blank lines in a row.

Remov

sys: Automated cleanup of cdefs and other formatting

Apply the following automated changes to try to eliminate
no-longer-needed sys/cdefs.h includes as well as now-empty
blank lines in a row.

Remove /^#if.*\n#endif.*\n#include\s+<sys/cdefs.h>.*\n/
Remove /\n+#include\s+<sys/cdefs.h>.*\n+#if.*\n#endif.*\n+/
Remove /\n+#if.*\n#endif.*\n+/
Remove /^#if.*\n#endif.*\n/
Remove /\n+#include\s+<sys/cdefs.h>\n#include\s+<sys/types.h>/
Remove /\n+#include\s+<sys/cdefs.h>\n#include\s+<sys/param.h>/
Remove /\n+#include\s+<sys/cdefs.h>\n#include\s+<sys/capsicum.h>/

Sponsored by: Netflix

show more ...

sys: Remove $FreeBSD$: one-line .c pattern

Remove /^[\s*]*__FBSDID\("\$FreeBSD\$"\);?\s*\n/

spdx: The BSD-2-Clause-FreeBSD identifier is obsolete, drop -FreeBSD

The SPDX folks have obsoleted the BSD-2-Clause-FreeBSD identifier. Catch
up to that fact and revert to their recommended match of

spdx: The BSD-2-Clause-FreeBSD identifier is obsolete, drop -FreeBSD

The SPDX folks have obsoleted the BSD-2-Clause-FreeBSD identifier. Catch
up to that fact and revert to their recommended match of BSD-2-Clause.

Discussed with: pfg
MFC After: 3 days
Sponsored by: Netflix

show more ...

spi flash: Remove unused devclass arguments to DRIVER_MODULE.

Merge ^/head r357408 through r357661.

Ever since the block layer expanded its command syntax beyond just
BIO_READ and BIO_WRITE, we've handled this expanded syntax poorly in
drivers when the driver doesn't support a particular command.

Ever since the block layer expanded its command syntax beyond just
BIO_READ and BIO_WRITE, we've handled this expanded syntax poorly in
drivers when the driver doesn't support a particular command. Do a
sweep and fix that.

Reported by: imp

show more ...

Regularize my copyright notice

o Remove All Rights Reserved from my notices
o imp@FreeBSD.org everywhere
o regularize punctiation, eliminate date ranges
o Make sure that it's clear that I don't clai

Regularize my copyright notice

o Remove All Rights Reserved from my notices
o imp@FreeBSD.org everywhere
o regularize punctiation, eliminate date ranges
o Make sure that it's clear that I don't claim All Rights reserved by listing
All Rights Reserved on same line as other copyright holders (but not
me). Other such holders are also listed last where it's clear.

show more ...

MFHead @348740

Sponsored by: The FreeBSD Foundation

Use the new FDTCOMPAT_PNP_INFO() macro to define SPIBUS_FDT_PNP_INFO().
Also rename SPIBUS_PNP_INFO -> SPIBUS_FDT_PNP_INFO because there could be
other kinds of pnpinfo for other (non-fdt) bus attach

Use the new FDTCOMPAT_PNP_INFO() macro to define SPIBUS_FDT_PNP_INFO().
Also rename SPIBUS_PNP_INFO -> SPIBUS_FDT_PNP_INFO because there could be
other kinds of pnpinfo for other (non-fdt) bus attachments.

show more ...

MFHead@r345275

MFhead@r344996

Give the mx25l device sole ownership of the name /dev/flash/spi* instead of
trying to use disk_add_alias() to make spi* an alias for mx25l*. It turns
out disk_add_alias() works for partitions, but n

Give the mx25l device sole ownership of the name /dev/flash/spi* instead of
trying to use disk_add_alias() to make spi* an alias for mx25l*. It turns
out disk_add_alias() works for partitions, but not slices, and that's hard
to fix.

This change is, in effect, a partial revert of r344526.

The mips world relies on the existence of flashmap names formatted as
/dev/flash/spi0s.name, whereas pretty much nothing relies on at45d devices
using the /dev/spi* names (because until recently the at45d driver didn't
even work reliably). So this change makes mx25l devices the sole owner of
the /dev/flash/spi* namespace, which actually makes some sense because it is
a SpiFlash(tm) device, so flash/spi isn't a horrible name.

Reported by: Mori Hiroki <yamori813@yahoo.co.jp>

show more ...

MFhead@r344786

Merge ^/head r344549 through r344775.

Allow the sector size of the disk device to be configured using hints or
FDT data. The sector size must be a multiple of the device's page size.
If not configured, use the historical default of the

Allow the sector size of the disk device to be configured using hints or
FDT data. The sector size must be a multiple of the device's page size.
If not configured, use the historical default of the device page size.

Setting the disk sector size to 512 or 4096 allows a variety of standard
filesystems to be used on the device. Of course you wouldn't want to be
writing frequently to a SPI flash chip like it was a disk drive, but for
data that gets written once (or rarely) and read often, using a standard
filesystem is a nice convenient thing.

show more ...

Add some comments. Give #define'd names to some scattered numbers. Change
some #define'd names to be more descriptive. When reporting a post-write
compare failure, report the page number, not the

Add some comments. Give #define'd names to some scattered numbers. Change
some #define'd names to be more descriptive. When reporting a post-write
compare failure, report the page number, not the byte address of the page.
The latter is the only functional change, it makes the number match the
words of the error message.

show more ...

Bugfix: use a dummy buffer for the inactive side of a transfer.

This is especially important for writes. SPI is inherently a bidirectional
bus; you receive data (even if it's garbage) while writing

Bugfix: use a dummy buffer for the inactive side of a transfer.

This is especially important for writes. SPI is inherently a bidirectional
bus; you receive data (even if it's garbage) while writing. We should not
receive that data into the same buffer we're writing to the device.

When reading it doesn't matter what we send to the device, but using the
dummy buffer for that as well is pleasingly symmetrical.

show more ...

Add a module dependency on fdt_slicer. Also, move the PNP_INFO to its more
usual location, down near the DRIVER_MODULE() stuff.

Add support for geom_flashmap by providing a getattr() for "SPI:device".

Merge ^/head r344513 through r344548.

Fix a paste-o that broke the build on all arches.

Reported by: many
Pointy hat: ian@

MFhead@r344527

Resolve a name conflict when both SpiFlash and DataFlash devices are present.

Both SpiFlash (mx25l) and DataFlash (at45d) drivers create a disk device
with a name of /dev/flash/spiN where N is the d

Resolve a name conflict when both SpiFlash and DataFlash devices are present.

Both SpiFlash (mx25l) and DataFlash (at45d) drivers create a disk device
with a name of /dev/flash/spiN where N is the driver's unit number. If
both types of devices are present in the same system, this creates a fatal
conflict that prevents attachment of whichever device attaches second
(because mx25l0 and at45d0 both try to create a spi0).

This gives each type of device a unique name (mx25lN or at45dN respectively)
and also adds an alias of spiN for compatibility. When both device types
appear in the same system, only the first to attach gets the spiN alias.
When the second device attaches there is a non-fatal warning that the alias
can't be created, but both devices are still accessible via their primary
names (and there is no need for the spiN name to work for backwards
compatibility on such a system, because it has never been possible to use
the spiN names when both devices exist).

show more ...

Add a metadata entry for the AT45DB641E chip. This chip has the same 3-byte
jedec ID as its older cousin the AT45DB642D, but uses a different page size.
The only way to distinguish between the two c

Add a metadata entry for the AT45DB641E chip. This chip has the same 3-byte
jedec ID as its older cousin the AT45DB642D, but uses a different page size.
The only way to distinguish between the two chips is that the 2D chip has
0 bytes of extended ID info and the new 1E has 1 byte of extended ID. The
actual value of the extended ID byte is all zeroes. In other words, it's
the presence of the extended info that identifies this chip. (Presumably
a future upgrade might define non-zero values for the extended ID byte.)

show more ...

Include the jedec "extended device information string" in the criteria used
to match a chip to our table of metadata describing the chips. At least one
new DataFlash chip has a 3-byte jedec ID identi

Include the jedec "extended device information string" in the criteria used
to match a chip to our table of metadata describing the chips. At least one
new DataFlash chip has a 3-byte jedec ID identical to its predecessors and
differs only in the extended info, and it has different metadata requiring a
unique entry in the table. This paves the way for supporting such chips.

The metadata table now includes two new fields, extmask and extid. The two
bytes of extended info obtained from the chip are ANDed with extmask then
compared to extid, so it's possible to use only a subset of the extended
info in the matching.

We now always read 6 bytes of jedec ID info. Most chips don't return any
extended info, and the values read back for those two bytes may be
indeterminate, but such chips have extmask and extid values of 0x0000 in the
table, so the extid effectively doesn't participate in the matching on those
chips and it doesn't matter what they return in the extended info bytes.

show more ...