sys: Remove $FreeBSD$: two-line .h pattern

Remove /^\s*\*\n \*\s+\$FreeBSD\$$\n/

Mechanically convert dc(4) to IfAPI

Sponsored by: Juniper Networks, Inc.
Differential Revision: https://reviews.freebsd.org/D37852

Merge ^/head r325842 through r325998.

spdx: initial adoption of licensing ID tags.

The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensou

spdx: initial adoption of licensing ID tags.

The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.

Special thanks to Wind River for providing access to "The Duke of
Highlander" tool: an older (2014) run over FreeBSD tree was useful as a
starting point.

Initially, only tag files that use BSD 4-Clause "Original" license.

RelNotes: yes
Differential Revision: https://reviews.freebsd.org/D13133

show more ...

IFC @230489 (pending review).

IFC @ r227804

Pull in the virtio drivers from head.

Partially revert r218788. r218788 removed calling dc_setcfg() for
!DC_IS_ADMTEK in dc_miibus_statchg(). This change broke link
establishment of Intel 21143 with dcphy(4) where it stuck in
"ability de

Partially revert r218788. r218788 removed calling dc_setcfg() for
!DC_IS_ADMTEK in dc_miibus_statchg(). This change broke link
establishment of Intel 21143 with dcphy(4) where it stuck in
"ability detect" state without completing auto-negotiation.
Also nuke dc_if_media as it's not actually used.

Submitted by: marius

show more ...

- Import the common MII bitbang'ing code from NetBSD and convert drivers to
take advantage of it instead of duplicating it. This reduces the size of
the i386 GENERIC kernel by about 4k. The only

- Import the common MII bitbang'ing code from NetBSD and convert drivers to
take advantage of it instead of duplicating it. This reduces the size of
the i386 GENERIC kernel by about 4k. The only potential in-tree user left
unconverted is xe(4), which generally should be changed to use miibus(4)
instead of implementing PHY handling on its own, as otherwise it makes not
much sense to add a dependency on miibus(4)/mii_bitbang(4) to xe(4) just
for the MII bitbang'ing code. The common MII bitbang'ing code also is
useful in the embedded space for using GPIO pins to implement MII access.
- Based on lessons learnt with dc(4) (see r185750), add bus barriers to the
MII bitbang read and write functions of the other drivers converted in
order to ensure the intended ordering. Given that register access via an
index register as well as register bank/window switching is subject to the
same problem, also add bus barriers to the respective functions of smc(4),
tl(4) and xl(4).
- Sprinkle some const.

Thanks to the following testers:
Andrew Bliznak (nge(4)), nwhitehorn@ (bm(4)), yongari@ (sis(4) and ste(4))
Thanks to Hans-Joerg Sirtl for supplying hardware to test stge(4).

Reviewed by: yongari (subset of drivers)
Obtained from: NetBSD (partially)

show more ...

IFC @ r226824

Add support for ALi/ULi, now NVIDIA, M5261/M5263 PCI FastEthernet
controller which is found on ULi M1563 South Bridge & M1689 Bridge.
These controllers look like a tulip clone.
M5263 controller does

Add support for ALi/ULi, now NVIDIA, M5261/M5263 PCI FastEthernet
controller which is found on ULi M1563 South Bridge & M1689 Bridge.
These controllers look like a tulip clone.
M5263 controller does not support MII bitbang so use DC_ROM
register to access MII registers. Like other tulip variants, ULi
controller uses a setup frame to configure RX filter and uses new
setup frame format. It's not clear to me whether the controller
supports a hash based multicast filtering so this patch uses 14
perfect multicast filter to filter multicast frames. If number of
multicast addresses is greater than 14, controller is put into a
mode that receives all multicast frames.
Due to lack of access to M5261, this change was not tested with
M5261 but it probably works. Many thanks to Marco who provided
remote access to M5263.

Tested by: Marco Steinbach <coco <> executive-computing dot de>,
Martin MATO <martin.mato <> orange dot fr>

show more ...

Merge svn+ssh://svn.freebsd.org/base/head@218875

s/u_intXX_t/uintXX_t/g

Consistently use a tab character instead of space after #define.
No functional changes.

Split common TX/RX descriptor DMA tag to TX and RX DMA tags
respectively and fix all bus_dma(9) issues seen when bounce buffers
are used.
o Setup frame handling had no bus_dmamap_sync(9) which preve

Split common TX/RX descriptor DMA tag to TX and RX DMA tags
respectively and fix all bus_dma(9) issues seen when bounce buffers
are used.
o Setup frame handling had no bus_dmamap_sync(9) which prevented
driver from configuring RX filter. Add missing bus_dmamap_sync(9)
in both dc_setfilt_21143()/dc_setfilt_xircom() and dc_txeof().
o Use bus_addr_t for DMA segment instead of using u_int32_t.
o Introduce dc_dma_alloc()/dc_dma_free() functions to allocate/free
DMA'able memory.
o Create two DMA descriptor list for each TX/RX lists. This change
will minimize the size of bounce buffers that would be used in
each TX/RX path. Previously driver had to copy both TX/RX lists
when bounce buffer is active.
o 21143 data sheet says descriptor list requires 4 bytes alignment.
Remove PAGE_SIZE alignment restriction and use
sizeof(struct dc_dec).
o Setup frame requires 4 bytes alignment. Remove PAGE_SIZE
alignment restriction and use sizeof(struct dc_dec).
o Add missing DMA map unload for both setup frame and TX/RX
descriptor list.
o Overhaul RX handling logic such that make driver always allocate
new RX buffer with dc_newbuf(). Previously driver allowed to
copy received frame with m_devget(9) after passing the
descriptor ownership to controller. This can lead to passing
wrong frame to upper stack.
o Introduce dc_discard_rxbuf() which will discard received frame
and reuse loaded DMA map and RX mbuf.
o Correct several wrong bus_dmamap_sync(9) usage in dc_rxeof and
dc_txeof. The TX/RX descriptor lists are updated by both driver
and HW so READ/WRITE semantics should be used.
o If driver failed to allocate new RX buffer, update if_iqdrops
counter instead of if_ierrors since driver received the frame
without errors.
o Make sure to unload loaded setup frame DMA map in dc_txeof and
clear the mark of setup frame of the TX descriptor in dc_txeof().
o Add check for possible TX descriptor overruns in dc_encap() and
move check for free buffer to caller, dc_start_locked().
o Swap the loaded DMA map and the last DMA map for multi-segmented
frames. Since dc_txeof() assumes the last descriptor of the
frame has the DMA map, driver should swap the first and the last
DMA map in dc_encap(). Previously driver tried to unload
not-yet-loaded DMA map such that the loaded DMA map was not
unloaded at all for multi-segmented frames.
o Rewrite DC_RXDESC/DC_TXDESC macro to simpler one.
o Remove definition of ETHER_ALIGN, it's already defined in
ethernet.h.

With this changes, dc(4) works with bounce buffers and it shall
also fix issues which might have shown in PAE environments.

Tested by: marius

show more ...

Merge svn+ssh://svn.freebsd.org/base/head@218816

For controllers that have TX interrupt moderation capability,
request TX completion interrupt for every 8-th frames. Previously
dc(4) requested TX completion interrupt if number of queued TX
descript

For controllers that have TX interrupt moderation capability,
request TX completion interrupt for every 8-th frames. Previously
dc(4) requested TX completion interrupt if number of queued TX
descriptors is greater than 64. This caused a lot of TX completion
interrupt under high TX load once driver queued more than 64 TX
descriptors. It's quite normal to see more than 64 queued TX
descriptors under high TX load.
This change reduces the number of TX completion interrupts to be
less than 17k under high TX load. Because this change does not
generate TX completion interrupt for each frame, add reclaiming
transmitted buffers in dc_tick not to generate false watchdog
timeouts.
While I'm here add check for queued descriptors in dc_txeof() since
there is no more work to do when there is no pending descriptors.

show more ...

Remove use case of DC_TX_ONE. It was used to limit queue just 1 TX
frame in DM910x controllers. In r67595(more than 10 years ago) it
was replaced to use "Store and Forward" mode and made controller
g

Remove use case of DC_TX_ONE. It was used to limit queue just 1 TX
frame in DM910x controllers. In r67595(more than 10 years ago) it
was replaced to use "Store and Forward" mode and made controller
generate TX completion interrupt for every frame.

show more ...

Always check memory allocation failure. If driver encounter memory
allocation error, do not attach driver.

Reviewed by: marius

Merge svn+ssh://svn.freebsd.org/base/head@214309

It seems some multi-port dc(4) controllers shares SROM of the first
port such that reading station address from second port always
returned 0xFF:0xFF:0xFF:0xFF:0xFF:0xFF Unfortunately it seems there

It seems some multi-port dc(4) controllers shares SROM of the first
port such that reading station address from second port always
returned 0xFF:0xFF:0xFF:0xFF:0xFF:0xFF Unfortunately it seems there
is no easy way to know whether SROM is shared or not. Workaround
the issue by traversing dc(4) device list and see whether we're
using second port and use station address of controller 0 as base
station address of second port.

PR: kern/79262
MFC after: 2 weeks

show more ...

IFH@204581

Merge from head at r201628.

# This hasn't been tested, and there are at least three bad commits
# that need to be backed out before the branch will be stable again.

cardbus -> CardBus

Fix card/device names, no functional change

The ADMtek AN985 is the cardbus variant of ADMtek AN983
The Netgear FA511 is just a relabled ADMtek AN985

PR: kern/50574
MFC after: 1 month

Merge from head up to r188941 (last revision before the USB stack switch)