cxgbe(4): Remove smt_idx from the L2 table entry structure.

An L2 table entry isn't associated with a particular SMT (Source MAC
Table) entry.

MFC after: 1 week
Sponsored by: Chelsio Communications

cxgbe(4): Stop and restart the L2T allocator with the LLD.

L2T entries are used by both filters and TOE and the L2T is shared
between the base driver (LLD) and the TOM ULD. Add a flag to indicate
t

cxgbe(4): Stop and restart the L2T allocator with the LLD.

L2T entries are used by both filters and TOE and the L2T is shared
between the base driver (LLD) and the TOM ULD. Add a flag to indicate
that the L2T is stopped, which means:
* t4_alloc_l2e and t4_l2t_alloc_switching will not allocate new entries.
* t4_tom will ignore all ARP/NDP updates from the kernel.
* Previously allocated L2T entries can still be freed.

MFC after: 1 month
Sponsored by: Chelsio Communications

show more ...

cxgbe(4): Make no assumptions about the start and size of the L2T table.

Do not assume that the table starts at index 0 and is typically 4K in
size. The only thing the driver needs to verify is tha

cxgbe(4): Make no assumptions about the start and size of the L2T table.

Do not assume that the table starts at index 0 and is typically 4K in
size. The only thing the driver needs to verify is that its use of
F_SYNC_WR doesn't collide with the L2T hwidx range.

Reviewed by: jhb
MFC after: 1 week
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D46028

show more ...

cxgbe(4): Tidy up t4_l2t.h

Align the comment for if_t with the rest and remove the declaration of
t4_l2t_set_switching, which was removed in 061bbaf7e7fe.

No functional change.

MFC after: 3 days
S

cxgbe(4): Tidy up t4_l2t.h

Align the comment for if_t with the rest and remove the declaration of
t4_l2t_set_switching, which was removed in 061bbaf7e7fe.

No functional change.

MFC after: 3 days
Sponsored by: Chelsio Communications

show more ...

sys: Remove $FreeBSD$: two-line .h pattern

Remove /^\s*\*\n \*\s+\$FreeBSD\$$\n/

spdx: The BSD-2-Clause-FreeBSD identifier is obsolete, drop -FreeBSD

The SPDX folks have obsoleted the BSD-2-Clause-FreeBSD identifier. Catch
up to that fact and revert to their recommended match of

spdx: The BSD-2-Clause-FreeBSD identifier is obsolete, drop -FreeBSD

The SPDX folks have obsoleted the BSD-2-Clause-FreeBSD identifier. Catch
up to that fact and revert to their recommended match of BSD-2-Clause.

Discussed with: pfg
MFC After: 3 days
Sponsored by: Netflix

show more ...

Mechanically convert cxgb(4) and cxgbe(4) to IfAPI

Reviewed by: np
Sponsored by: Juniper Networks, Inc.
Differential Revision: https://reviews.freebsd.org/D38597

NIC KTLS for Chelsio T6 adapters.

This adds support for ifnet (NIC) KTLS using Chelsio T6 adapters.
Unlike the TOE-based KTLS in r353328, NIC TLS works with non-TOE
connections.

NIC KTLS on T6 is n

NIC KTLS for Chelsio T6 adapters.

This adds support for ifnet (NIC) KTLS using Chelsio T6 adapters.
Unlike the TOE-based KTLS in r353328, NIC TLS works with non-TOE
connections.

NIC KTLS on T6 is not able to use the normal TSO (LSO) path to segment
the encrypted TLS frames output by the crypto engine. Instead, the
TOE is placed into a special setup to permit "dummy" connections to be
associated with regular sockets using KTLS. This permits using the
TOE to segment the encrypted TLS records. However, this approach does
have some limitations:

1) Regular TOE sockets cannot be used when the TOE is in this special
mode. One can use either TOE and TOE-based KTLS or NIC KTLS, but
not both at the same time.

2) In NIC KTLS mode, the TOE is only able to accept a per-connection
timestamp offset that varies in the upper 4 bits. Put another way,
only connections whose timestamp offset has the 28 lower bits
cleared can use NIC KTLS and generate correct timestamps. The
driver will refuse to enable NIC KTLS on connections with a
timestamp offset with any of the lower 28 bits set. To use NIC
KTLS, users can either disable TCP timestamps by setting the
net.inet.tcp.rfc1323 sysctl to 0, or apply a local patch to the
tcp_new_ts_offset() function to clear the lower 28 bits of the
generated offset.

3) Because the TCP segmentation relies on fields mirrored in a TCB in
the TOE, not all fields in a TCP packet can be sent in the TCP
segments generated from a TLS record. Specifically, for packets
containing TCP options other than timestamps, the driver will
inject an "empty" TCP packet holding the requested options (e.g. a
SACK scoreboard) along with the segments from the TLS record.
These empty TCP packets are counted by the
dev.cc.N.txq.M.kern_tls_options sysctls.

Unlike TOE TLS which is able to buffer encrypted TLS records in
on-card memory to handle retransmits, NIC KTLS must re-encrypt TLS
records for retransmit requests as well as non-retransmit requests
that do not include the start of a TLS record but do include the
trailer. The T6 NIC KTLS code tries to optimize some of the cases for
requests to transmit partial TLS records. In particular it attempts
to minimize sending "waste" bytes that have to be given as input to
the crypto engine but are not needed on the wire to satisfy mbufs sent
from the TCP stack down to the driver.

TCP packets for TLS requests are broken down into the following
classes (with associated counters):

- Mbufs that send an entire TLS record in full do not have any waste
bytes (dev.cc.N.txq.M.kern_tls_full).

- Mbufs that send a short TLS record that ends before the end of the
trailer (dev.cc.N.txq.M.kern_tls_short). For sockets using AES-CBC,
the encryption must always start at the beginning, so if the mbuf
starts at an offset into the TLS record, the offset bytes will be
"waste" bytes. For sockets using AES-GCM, the encryption can start
at the 16 byte block before the starting offset capping the waste at
15 bytes.

- Mbufs that send a partial TLS record that has a non-zero starting
offset but ends at the end of the trailer
(dev.cc.N.txq.M.kern_tls_partial). In order to compute the
authentication hash stored in the trailer, the entire TLS record
must be sent as input to the crypto engine, so the bytes before the
offset are always "waste" bytes.

In addition, other per-txq sysctls are provided:

- dev.cc.N.txq.M.kern_tls_cbc: Count of sockets sent via this txq
using AES-CBC.

- dev.cc.N.txq.M.kern_tls_gcm: Count of sockets sent via this txq
using AES-GCM.

- dev.cc.N.txq.M.kern_tls_fin: Count of empty FIN-only packets sent to
compensate for the TOE engine not being able to set FIN on the last
segment of a TLS record if the TLS record mbuf had FIN set.

- dev.cc.N.txq.M.kern_tls_records: Count of TLS records sent via this
txq including full, short, and partial records.

- dev.cc.N.txq.M.kern_tls_octets: Count of non-waste bytes (TLS header
and payload) sent for TLS record requests.

- dev.cc.N.txq.M.kern_tls_waste: Count of waste bytes sent for TLS
record requests.

To enable NIC KTLS with T6, set the following tunables prior to
loading the cxgbe(4) driver:

hw.cxgbe.config_file=kern_tls
hw.cxgbe.kern_tls=1

Reviewed by: np
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D21962

show more ...

MFH r338661 through r339200.

Sponsored by: The FreeBSD Foundation

Merge ^/head r338731 through r338987.

cxgbe(4): Reuse existing "switching" L2T entries when possible.

Approved by: re@ (rgrimes@)
Sponsored by: Chelsio Communications

cxgbe(4): Retire an old check.

sys/dev: further adoption of SPDX licensing ID tags.

Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error

sys/dev: further adoption of SPDX licensing ID tags.

Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.

The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.

show more ...

cxgbe(4): Changes to the CPL-handler registration mechanism and code
related to "shared" CPLs.

a) Combine t4_set_tcb_field and t4_set_tcb_field_rpl into a single
function. Allow callers to direct t

cxgbe(4): Changes to the CPL-handler registration mechanism and code
related to "shared" CPLs.

a) Combine t4_set_tcb_field and t4_set_tcb_field_rpl into a single
function. Allow callers to direct the response to any iq. Tidy up
set_ulp_mode_iscsi while there to use names from t4_tcb.h instead of
magic constants.

b) Remove all CPL handler tables from struct adapter. This reduces its
size by around 2KB. All handlers are now registered at MOD_LOAD instead
of attach or some kind of initialization/activation. The registration
functions do not need an adapter parameter any more.

c) Add per-iq handlers to deal with CPLs whose destination cannot be
determined solely from the opcode. There are 2 such CPLs in use right
now: SET_TCB_RPL and L2T_WRITE_RPL. The base driver continues to send
filter and L2T_WRITEs over the mgmtq and solicits the reply on fwq.
t4_tom (including the DDP code) now uses the port's ctrlq to send
L2T_WRITEs and SET_TCB_FIELDs and solicits the reply on an ofld_rxq.
fwq and ofld_rxq have different handlers that know what kind of tid to
expect in the reply. Update t4_write_l2e and callers to to support any
wrq/iq combination.

Approved by: re@ (kib@)
Sponsored by: Chelsio Communications

show more ...

Merge fresh head.

IFC @247348.

Sync with HEAD.

IFC @ r245509

cxgbe(4): Updates to the hardware L2 table management code.

- Add full support for IPv6 addresses.

- Read the size of the L2 table during attach. Do not assume that PCIe
physical function 4 of t

cxgbe(4): Updates to the hardware L2 table management code.

- Add full support for IPv6 addresses.

- Read the size of the L2 table during attach. Do not assume that PCIe
physical function 4 of the card has all of the table to itself.

- Use FNV instead of Jenkins to hash L3 addresses and drop the private
copy of jhash.h from the driver.

MFC after: 1 week

show more ...

MFC

MFC @ r241285

IFC @ r242684

Sync from head

Prefer __containerof() over __member2struct().

The former works better with qualifiers, but also properly type checks
the input pointer.

Use native FreeBSD facilities everywhere except the shared code in common/

MFC after: 1 week