sys: Remove $FreeBSD$: two-line .h pattern

Remove /^\s*\*\n \*\s+\$FreeBSD\$$\n/

spdx: The BSD-2-Clause-FreeBSD identifier is obsolete, drop -FreeBSD

The SPDX folks have obsoleted the BSD-2-Clause-FreeBSD identifier. Catch
up to that fact and revert to their recommended match of

spdx: The BSD-2-Clause-FreeBSD identifier is obsolete, drop -FreeBSD

The SPDX folks have obsoleted the BSD-2-Clause-FreeBSD identifier. Catch
up to that fact and revert to their recommended match of BSD-2-Clause.

Discussed with: pfg
MFC After: 3 days
Sponsored by: Netflix

show more ...

ath: clean up empty lines in .c and .h files

sys/dev: further adoption of SPDX licensing ID tags.

Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error

sys/dev: further adoption of SPDX licensing ID tags.

Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.

The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.

show more ...

Merge from head

IFC @ r254014

IFC @253398

Merge fresh head.

Migrate the LNA mixing diversity machinery from the AR9285 HAL to the driver.

The AR9485 chip and AR933x SoC both implement LNA diversity.
There are a few extra things that need to happen before thi

Migrate the LNA mixing diversity machinery from the AR9285 HAL to the driver.

The AR9485 chip and AR933x SoC both implement LNA diversity.
There are a few extra things that need to happen before this can be
flipped on for those chips (mostly to do with setting up the different
bias values and LNA1/LNA2 RSSI differences) but the first stage is
putting this code into the driver layer so it can be reused.

This has the added benefit of making it easier to expose configuration
options and diagnostic information via the ioctl API. That's not yet
being done but it sure would be nice to do so.

Tested:

* AR9285, with LNA diversity enabled
* AR9285, with LNA diversity disabled in EEPROM

show more ...

Remove the AR9285 specific structure for LNA diversity and use the HAL.

The AR9300 HAL update included the LNA diversity configuration information
so it can be used in the AR9485 configuration code.

MFC @ r241285

IFC @ r242684

Sync from head

Merge head r233826 through r240095.

Migrate the AR9285 diversity configuration LNA configuration to use
some HAL definitions rather than local definitions.

The original source (ath9k) pulled this stuff from the QCA driver and
removed

Migrate the AR9285 diversity configuration LNA configuration to use
some HAL definitions rather than local definitions.

The original source (ath9k) pulled this stuff from the QCA driver and
removed the HAL_* prefix. I'm just restoring the correct order of things.

Obtained from: Qualcomm Atheros

show more ...

MFC

Some diversity changes relating to AR9285.

* grab the main, alt and selected LNA config
* add some optional / disabled logging code
* add a check to reject packets with an invalid main rssi too,
i

Some diversity changes relating to AR9285.

* grab the main, alt and selected LNA config
* add some optional / disabled logging code
* add a check to reject packets with an invalid main rssi too,
in case the alt is the active receive chain and main is -ve.

Note: The software-controlled combined diversity code is still disabled.

show more ...

MFC

Import some initial Kite fixed diversity code from Atheros.

For now, the diversity settings are controlled by 'txantenna',
-not- rxantenna. This is because the earlier chipsets had
controllable TX d

Import some initial Kite fixed diversity code from Atheros.

For now, the diversity settings are controlled by 'txantenna',
-not- rxantenna. This is because the earlier chipsets had
controllable TX diversity; the RX antenna setting twiddles
the default antenna register. I'll try sort that stuff out at
some point.

Call the antenna switch function from the board setup function
so scans, channel changes, mode changes, etc don't set the
diversity back to a default state too far from what's intended.

Things to todo:

* Squirrel away the last antenna diversity/combining parameters
and restore them during board setup if HAL_ANT_VARIABLE is
defined. That way scans, etc don't reset the diversity settings.

* Add some more public facing statistics, rather than what's
simply logged under HAL_DEBUG_DIVERSITY.

For now, the fixed antenna settings behave better than variable
settings for me. I have some further fiddling to do..

Obtained from: Atheros

show more ...

More kite diversity related changes.

* add a diversity flag to the HAL debugging section
* add a check to make sure the kite diversity code doesn't run
on boards that don't require it, as not all

More kite diversity related changes.

* add a diversity flag to the HAL debugging section
* add a check to make sure the kite diversity code doesn't run
on boards that don't require it, as not all Kite chips will
implement it.
* add some debug statements when the diversity code makes
changes to the antenna diversity/combining setup.

show more ...

Bring over the antenna diversity logic support for Kite.

Again, this is just the code ported from ath9k and included in the build,
it isn't yet enabled.