sys: Remove $FreeBSD$: two-line .h pattern

Remove /^\s*\*\n \*\s+\$FreeBSD\$$\n/

[ath_hal] Add get/set NAV functions

The NAV (network allocation vector) register reflects the current MAC
tracking of NAV - when it will stay quiet before transmitting.

Other devices transmit their

[ath_hal] Add get/set NAV functions

The NAV (network allocation vector) register reflects the current MAC
tracking of NAV - when it will stay quiet before transmitting.

Other devices transmit their frame durations in their 802.11 PHY headers
and all devices that hear a frame - even if it's one in an encoding
they don't understand - will understand the low bitrate PHY header that
includes the frame duration. So, they'll set NAV to this value so
they'll stay quiet until the transmit completes.

Anyway, sometimes the PHY NAV header is garbled and sometimes, notably
older broadcom devices, will fake a long NAV so they can get "cleaner" air
for local calibration. When this happens, the hardware will stay quiet
for quite some time and this can lead to missed/stuck beacons, or
(for Very Large Values) a MAC hang.

This code just adds the ability to get/set the NAV; the driver will
need to take care of using it during transmit hangs and beacon misses
to see if it's due to a trash looking NAV.

show more ...

ath: clean up empty lines in .c and .h files

SPDX: license IDs for some ISC-related files.

Merge ^/head r313301 through r313643.

[ath_hal] implement NULL methods for ah_setQuiet for AR5210, AR5211.

Tested:

* "crap, I didn't bring my cardbus collection and T400 with me" compile
tested.

Merge fresh head.

sync from head

IFC @247348.

Begin adding support to explicitly set the current chainmask.

Right now the only way to set the chainmask is to set the hardware
configured chainmask through capabilities. This is fine for forcing

Begin adding support to explicitly set the current chainmask.

Right now the only way to set the chainmask is to set the hardware
configured chainmask through capabilities. This is fine for forcing
the chainmask to be something other than what the hardware is capable
of (eg to reduce TX/RX to one connected antenna) but it does change what
the HAL hardware chainmask configuration is.

For operational mode changes, it (may?) make sense to separately control
the TX/RX chainmask.

Right now it's done as part of ar5416_reset.c - ar5416UpdateChainMasks()
calculates which TX/RX chainmasks to enable based on the operating mode.
(1 for legacy and whatever is supported for 11n operation.) But doing
this in the HAL is suboptimal - the driver needs to know the currently
configured chainmask in order to correctly enable things for each
TX descriptor. This is currently done by overriding the chainmask
config in the ar5416 TX routines but this has to disappear - the AR9300
HAL support requires the driver to dynamically set the TX chainmask based
on the TX power and TX rate in order to meet mini-PCIe slot power
requirements.

So:

* Introduce a new HAL method to set the operational chainmask variables;
* Introduce null methods for the previous generation chipsets;
* Add new driver state to record the current chainmask separate from
the hardware configured chainmask.

Part #2 of this will involve disabling ar5416UpdateChainMasks() and moving
it into the driver; as well as properly programming the TX chainmask
based on the currently configured HAL chainmask.

Tested:

* AR5416, STA mode - both legacy (11a/11bg) and 11n rates - verified
that AR_SELFGEN_MASK (the chainmask used for self-generated frames like
ACKs and RTSes) is correct, as well as the TX descriptor contents is
correct.

show more ...

IFC @ r238370

Merge head r233826 through r236168.

MFC

Add some empty DFS methods for AR5210/AR5211 for now, if DFS is enabled
but these don't exist, the code panics.

I should really just add or use a DFS HAL capability before doing this,
so the methods

Add some empty DFS methods for AR5210/AR5211 for now, if DFS is enabled
but these don't exist, the code panics.

I should really just add or use a DFS HAL capability before doing this,
so the methods wouldn't be needed..

show more ...

Change the MIB cycle count API to return HAL_BOOL, rather than uint32_t,
to return whether it was successful.

Add placeholder (blank) methods for previous chips, for both it and
the 11n extension ch

Change the MIB cycle count API to return HAL_BOOL, rather than uint32_t,
to return whether it was successful.

Add placeholder (blank) methods for previous chips, for both it and
the 11n extension channel busy call.

show more ...

Merge svn+ssh://svn.freebsd.org/base/head@218816

ANI changes #1 - split out the ANI polling from the RxMonitor hook.

The rxmonitor hook is called on each received packet. This can get very,
very busy as the tx/rx/chanbusy registers are thus read e

ANI changes #1 - split out the ANI polling from the RxMonitor hook.

The rxmonitor hook is called on each received packet. This can get very,
very busy as the tx/rx/chanbusy registers are thus read each time a packet
is received.

Instead, shuffle out the true per-packet processing which is needed and move
the rest of the ANI processing into a periodic event which runs every 100ms
by default.

show more ...

Merge from head

Merge from head up to r188941 (last revision before the USB stack switch)

Update the projects tree to a newer FreeBSD current.

5416 and later parts mux the gpio outputs; extend the api to include
a signal type that's used to select the appropriate mux

Overhaul regulatory support:
o remove HAL_CHANNEL; convert the hal to use net80211 channels; this
mostly involves mechanical changes to variable names and channel
attribute macros
o gut HAL_CHANN

Overhaul regulatory support:
o remove HAL_CHANNEL; convert the hal to use net80211 channels; this
mostly involves mechanical changes to variable names and channel
attribute macros
o gut HAL_CHANNEL_PRIVATE as most of the contents are now redundant
with the net80211 channel available
o change api for ath_hal_init_channels: no more reglass id's, no more outdoor
indication (was a noop), anM contents
o add ath_hal_getchannels to have the hal construct a channel list without
altering runtime state; this is used to retrieve the calibration list for
the device in ath_getradiocaps
o add ath_hal_set_channels to take a channel list and regulatory data from
above and construct internal state to match (maps frequencies for 900MHz
cards, setup for CTL lookups, etc)
o compact the private channel table: we keep one private channel
per frequency instead of one per HAL_CHANNEL; this gives a big
space savings and potentially improves ani and calibration by
sharing state (to be seen; didn't see anything in testing); a new config
option AH_MAXCHAN controls the table size (default to 96 which
was chosen to be ~3x the largest expected size)
o shrink ani state and change to mirror private channel table (one entry per
frequency indexed by ic_devdata)
o move ani state flags to private channel state
o remove country codes; use net80211 definitions instead
o remove GSM regulatory support; it's no longer needed now that we
pass in channel lists from above
o consolidate ADHOC_NO_11A attribute with DISALLOW_ADHOC_11A
o simplify initial channel list construction based on the EEPROM contents;
we preserve country code support for now but may want to just fallback
to a WWR sku and dispatch the discovered country code up to user space
so the channel list can be constructed using the master regdomain tables
o defer to net80211 for max antenna gain
o eliminate sorting of internal channel table; now that we use ic_devdata
as an index, table lookups are O(1)
o remove internal copy of the country code; the public one is sufficient
o remove AH_SUPPORT_11D conditional compilation; we always support 11d
o remove ath_hal_ispublicsafetysku; not needed any more
o remove ath_hal_isgsmsku; no more GSM stuff
o move Conformance Test Limit (CTL) state from private channel to a lookup
using per-band pointers cached in the private state block
o remove regulatory class id support; was unused and belongs in net80211
o fix channel list construction to set IEEE80211_CHAN_NOADHOC,
IEEE80211_CHAN_NOHOSTAP, and IEEE80211_CHAN_4MSXMIT
o remove private channel flags CHANNEL_DFS and CHANNEL_4MS_LIMIT; these are
now set in the constructed net80211 channel
o store CHANNEL_NFCREQUIRED (Noise Floor Required) channel attribute in one
of the driver-private flag bits of the net80211 channel
o move 900MHz frequency mapping into the hal; the mapped frequency is stored
in the private channel and used throughout the hal (no more mapping in the
driver and/or net80211)
o remove ath_hal_mhz2ieee; it's no longer needed as net80211 does the
calculation and available in the net80211 channel
o change noise floor calibration logic to work with compacted private channel
table setup; this may require revisiting as we no longer can distinguish
channel attributes (e.g. 11b vs 11g vs turbo) but since the data is used
only to calculate status data we can live with it for now
o change ah_getChipPowerLimits internal method to operate on a single channel
instead of all channels in the private channel table
o add ath_hal_gethwchannel to map a net80211 channel to a h/w frequency
(always the same except for 900MHz channels)
o add HAL_EEBADREG and HAL_EEBADCC status codes to better identify regulatory
problems
o remove CTRY_DEBUG and CTRY_DEFAULT enum's; these come from net80211 now
o change ath_hal_getwirelessmodes to really return wireless modes supported
by the hardware (was previously applying regulatory constraints)
o return channel interference status with IEEE80211_CHANSTATE_CWINT (should
change to a callback so hal api's can take const pointers)
o remove some #define's no longer needed with the inclusion of
<net80211/_ieee80211.h>

Sponsored by: Carlson Wireless

show more ...

correct typo that left programmed sifs time in the slot time
(to be applied on subsequent resets)

Submitted by: Jiri Fojtasek <jiri.fojtasek@hlohovec.net>

integrate from head@185615

import ath hal