1 /* 2 * CDDL HEADER START 3 * 4 * The contents of this file are subject to the terms of the 5 * Common Development and Distribution License (the "License"). 6 * You may not use this file except in compliance with the License. 7 * 8 * You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE 9 * or http://www.opensolaris.org/os/licensing. 10 * See the License for the specific language governing permissions 11 * and limitations under the License. 12 * 13 * When distributing Covered Code, include this CDDL HEADER in each 14 * file and include the License file at usr/src/OPENSOLARIS.LICENSE. 15 * If applicable, add the following below this CDDL HEADER, with the 16 * fields enclosed by brackets "[]" replaced with your own identifying 17 * information: Portions Copyright [yyyy] [name of copyright owner] 18 * 19 * CDDL HEADER END 20 */ 21 /* 22 * Copyright 2007 Sun Microsystems, Inc. All rights reserved. 23 * Use is subject to license terms. 24 */ 25 26 #ifndef _SYS_ERI_MAC_H 27 #define _SYS_ERI_MAC_H 28 29 #pragma ident "%Z%%M% %I% %E% SMI" 30 31 #ifdef __cplusplus 32 extern "C" { 33 #endif 34 35 /* 36 * HOST MEMORY DATA STRUCTURES 37 * Transmit and Receive Descriptor Rings 38 */ 39 40 /* The Descriptor Ring base Addresses must be 2K-byte aligned */ 41 42 #define ERI_GMDALIGN (2048) 43 44 /* 45 * The transmit and receiver Descriptor Rings are organized as "wrap-around 46 * descriptors and are of programmable size. 47 * Each descriptor consists of two double-word entries: a control/status entry 48 * and a pointer to a data buffer. 49 * The no. of entries is programmable in binary increments, from 32 to 8192. 50 * TBD: Even though the Receive Desriptor ring size is 8k, provide for a user 51 * configurable variable to specify the max.no. of Rx buffers posted. 52 */ 53 54 #define ERI_TMDMAX (4096) /* Transmit descriptor ring size */ 55 #define ERI_RMDMAX (4096) /* Receive descriptor ring size */ 56 57 /* 58 * ----------------------------- 59 * Transmit descriptor structure 60 * ----------------------------- 61 */ 62 63 struct eri_tmd { 64 uint64_t tmd_flags; /* INTME, SOP, EOP, cksum, bufsize */ 65 uint64_t tmd_addr; /* buffer address */ 66 }; 67 68 /* fields in the tmd_flags */ 69 70 #define ERI_TMD_BUFSIZE (0x7fff << 0) /* 0-14 : Tx Data buffer size */ 71 /* valid values in range 0 - 17k */ 72 #define ERI_TMD_CSSTART (0x3f << 15) /* 15-20 : Checksum start offset */ 73 /* value must be even */ 74 #define ERI_TMD_CSSTUFF (0xff << 21) /* 21-28 : Checksum stuff offset */ 75 /* value must be even */ 76 #define ERI_TMD_CSENABL (1 << 29) /* 29 : Enable checksum computation */ 77 #define ERI_TMD_EOP (1 << 30) /* 30 : End Of Packet flag */ 78 #define ERI_TMD_SOP ((uint64_t)1 << 31) /* 31 : Packet Start flag */ 79 #define ERI_TMD_INTME ((uint64_t)1 << 32) /* 32 : Interrupt me now */ 80 #define ERI_TMD_NOCRC ((uint64_t)1 << 33) /* 33 : Do not insert CRC */ 81 82 #define ERI_TMD_CSSTART_SHIFT 15 /* checksum start bit position */ 83 #define ERI_TMD_CSSTUFF_SHIFT 21 /* checksum stuff bit position */ 84 85 /* 86 * TCP Header offset within Ethernet Packet: 87 * 14 Bytes Ethernet Header + 20 IP Header. 88 */ 89 90 #define ERI_TCPHDR_OFFSET 34 91 #define ERI_IPHDR_OFFSET 20 92 93 /* 94 * TCP Checksum stuff offset within Ethernet packet: 95 * 34 Bytes up to TCP Header + 16 Bytes within TCP header 96 */ 97 98 #define ERI_TCPCSUM_OFFSET 50 99 #define ERI_TMDCSUM_CTL (ERI_TMD_CSENABL | \ 100 (ERI_TCPHDR_OFFSET << ERI_TMD_CSSTART_SHIFT) | \ 101 (ERI_TCPCSUM_OFFSET << ERI_TMD_CSSTUFF_SHIFT)) 102 /* 103 * Programming Notes: 104 * 105 * 1. TX Kick Register is used to hand over TX descriptors to the hardware. 106 * TX Completion Register is used by hardware to handover TX descriptors 107 * back to the software. 108 * 109 * 2. ERI never writes back TX descriptors. 110 * 111 * 2. If a packet resides in more than one buffer, the Checksum_Enable, 112 * Checksum_Stuff_Offset, Checksum_Start_Offset and Int_me fields need to 113 * be set only in the first descriptor for the packet. 114 * 115 * 3. The hardware implementation relies on the fact that if a buffer 116 * starts at an "odd" boundary, the DMA state machine can "rewind" 117 * to the nearest burst boundary and execute a full DVMA burst Read. 118 * 119 * There is no other alignment restriction for the transmit data buffer. 120 */ 121 122 /* 123 * ----------------------------- 124 * Receive Descriptor structure 125 * ---------------------------- 126 */ 127 128 struct rmd { 129 uint64_t rmd_flags; 130 /* hash_val, hash_pass, bad, OWN, buf/data size, cksum */ 131 uint64_t rmd_addr; /* 8-byte aligned buffer address */ 132 }; 133 134 /* 135 * fields in the rmd_flags 136 */ 137 #define ERI_RMD_CKSUM (0xffff << 0) /* 0-15 : checksum computed */ 138 #define ERI_RMD_BUFSIZE (0x7fff << 16) /* 16-30 : buffer/frame size */ 139 #define ERI_RMD_OWN ((uint64_t)1 << 31) /* 31 : Ownership flag */ 140 /* 0 - owned by software */ 141 /* 1 - owned by hardware */ 142 #define ERI_RMD_RESERVED1 ((uint64_t)0xfff << 32) /* 32-43 : Reserved */ 143 #define ERI_RMD_HASHVAL ((uint64_t)0xffff << 44) /* 44-59 : hash value */ 144 #define ERI_RMD_HASHPASS ((uint64_t)1 << 60) /* 60 : pass hash filter */ 145 #define ERI_RMD_ALTERNATE ((uint64_t)1 << 61) 146 /* 61 : matched alternate MAC adrs */ 147 #define ERI_RMD_BAD ((uint64_t)1 << 62) /* 62 : bad CRC frame */ 148 #define ERI_RMD_RESERVED2 ((uint64_t)1 << 63) /* 63 : Reserved */ 149 150 #define ERI_RMD_BUFSIZE_SHIFT 16 /* buffer/data size bit position */ 151 152 #define ERI__RMD_BUFALIGN 8 153 154 /* 155 * ERI REGISTER SPACE 156 * The comments are in the following format: 157 * Addres_Offset R/W Default Actual_size(bits) Description 158 */ 159 160 /* 161 * Global Register Space : Paritally Modified for ERI 162 */ 163 struct global { 164 uint32_t seb_state; /* 0x0000 RO 0x00000000 03 SEB State Register */ 165 uint32_t config; /* 0x0004 RW 0x00000000 17 Configuration Register */ 166 uint32_t reserved2; /* 0x0008 */ 167 uint32_t status; /* 0x000C R-AC 0x00000000 25 Int. Status Register */ 168 uint32_t intmask; /* 0x0010 RW 0xFFFFFFFF 12 Interrupt Mask Reg */ 169 uint32_t intack; /* 0x0014 WO 0x00000000 06 Interrupt Ack Register */ 170 uint32_t reserved3; /* 0x0018 */ 171 uint32_t status_alias; /* 0x001C RO 0x00000000 25 Int. Stat Reg Alias */ 172 uint32_t reserved4[1016]; /* To skip to 0x1000 */ 173 uint32_t err_status; /* 0x1000 R-AC 0x00000000 03 PCI Error Status Reg. */ 174 uint32_t reset; /* 0x1010 RW-AC 0x00 3 Software Reset Reg */ 175 }; 176 177 /* 178 * 179 * SBus IO configuration (RW) 180 * To configure parameters that define the DMA burst and internal arbitration. 181 */ 182 #define ERI_SIOCFG_BSIZE32 (0x1 << 0) /* 32 byte burst sizeb state */ 183 #define ERI_SIOCFG_BSIZE64 (0x1 << 1) /* 64 byte burst sizeb state */ 184 #define ERI_SIOCFG_BSIZE128 (0x1 << 2) /* 128 byte burst sizeb state */ 185 #define ERI_SIOCFG_BMODE64 (0x1 << 3) /* Sbus 64 bit mode */ 186 #define ERI_SIOCFG_PARITY (0x1 << 9) /* Sbus Parity enabled. */ 187 188 /* 189 * SEB State Register (RO) 190 * Reflects the internal state of the arbitration between TX and RX 191 * DMA Channels. Used for diagnostics only 192 */ 193 #define ERI_SEB_ARBSTS (0x2 << 0) /* Arbiter state */ 194 #define ERI_SEB_RXWON (1 << 2) /* RX won the arbitration */ 195 196 /* 197 * Global Configuration Register (RW) 198 * To configure parameters that define the DMA burst and internal arbitration. 199 * TX/RX_DMA_LIMIT: No. of data transfers in 64-byte multiples 200 * 0 - peririty changes at packet boundaries 201 * default: 0x042 202 */ 203 #define ERI_G_CONFIG_BURST_SIZE (0x1 << 0) /* 0:infinite/64-byte burst */ 204 #define ERI_G_CONFIG_TX_DMA_LIM (0x1f << 1) /* 5-1: TX_DMA_Limit */ 205 #define ERI_G_CONFIG_RX_DMA_LIM (0x1f << 6) /* 10-6: RX_DMA_Limit */ 206 207 #define ERI_G_CONFIG_BURST_64 0x0 /* max burst size 64 */ 208 #define ERI_G_CONFIG_BURST_INF 0x1 /* infinite burst for whole pkt len */ 209 210 #define ERI_G_CONFIG_TX_DMA_LIM_SHIFT 1 211 #define ERI_G_CONFIG_RX_DMA_LIM_SHIFT 6 212 213 /* 214 * Global Interrupt Status Register (R-AC) 215 * size: 32 bits: 0-31 216 * default: 0x00000000 217 * This is the top level register used to communicate to the software events 218 * that were detected by the hardware. 219 * Top level bits 0-6 are automatically cleared to 0 when the Status Register 220 * is read. 221 * Second level interrupts reported by bits 13-18 are cleared at the source. 222 * The value of the TX Completion Register is replicated in bits 19-31. 223 */ 224 #define ERI_G_STATUS_TX_INT_ME (1 << 0) 225 /* 0 - set when a frame with INT_ME bit set is transferred to FIFO */ 226 #define ERI_G_STATUS_TX_ALL (1 << 1) /* 1 - TX desc. ring empty */ 227 #define ERI_G_STATUS_TX_DONE (1 << 2) /* 2 - from host to TX FIFO */ 228 #define ERI_G_STATUS_RES1 (1 << 3) /* 3 - reserved */ 229 #define ERI_G_STATUS_RX_DONE (1 << 4) /* 4 - from RXFIFO to host */ 230 #define ERI_G_STATUS_RX_NO_BUF (1 << 5) /* 5 - no RX buff available */ 231 #define ERI_G_STATUS_RX_TAG_ERR (1 << 6) /* 6 - RX tag error */ 232 #define ERI_G_STATUS_PERR_INT (1 << 7) /* 7 - Parity Err sts reg */ 233 #define ERI_G_STATUS_RES2 (0x3f << 7) /* 7-12 : reserved */ 234 #define ERI_G_STATUS_PCS_INT (1 << 13) /* 13 - PCS Interrupt */ 235 #define ERI_G_STATUS_TX_MAC_INT (1 << 14) /* 14 - TX MAC stat reg set */ 236 #define ERI_G_STATUS_RX_MAC_INT (1 << 15) /* 15 - RX MAC stat reg set */ 237 #define ERI_G_STATUS_MAC_CTRL_INT (1 << 16) /* 16 - MAC control reg */ 238 #define ERI_G_STATUS_MIF_INT (1 << 17) /* 17 - MIF status reg set */ 239 #define ERI_G_STATUS_BUS_ERR_INT (1 << 18) /* 18 - BUS Err sts reg */ 240 #define ERI_G_STATUS_TX_COMPL (0xfff80000) /* 19-31: TX Completion reg */ 241 242 #define ERI_G_STATUS_INTR (0xffffffff & ~(ERI_G_STATUS_TX_DONE |\ 243 ERI_G_STATUS_TX_ALL |\ 244 ERI_G_STATUS_MAC_CTRL_INT | ERI_G_STATUS_TX_COMPL)) 245 246 #define ERI_G_STATUS_TX_INT (ERI_G_STATUS_TX_DONE | ERI_G_STATUS_TX_ALL) 247 #define ERI_G_STATUS_RX_INT (~ERI_G_STATUS_TX_COMPL & ~ERI_G_STATUS_TX_INT) 248 249 #define ERI_G_STATUS_FATAL_ERR (ERI_G_STATUS_RX_TAG_ERR | \ 250 ERI_G_STATUS_PERR_INT | \ 251 ERI_G_STATUS_BUS_ERR_INT) 252 253 #define ERI_G_STATUS_NONFATAL_ERR (ERI_G_STATUS_TX_MAC_INT | \ 254 ERI_G_STATUS_RX_MAC_INT | \ 255 ERI_G_STATUS_MAC_CTRL_INT) 256 257 #define ERI_G_STATUS_TX_COMPL_SHIFT 19 258 #define ERI_G_STATUS_TX_COMPL_MASK 0x1fff 259 260 /* 261 * Global Interrupt Mask register (RW) 262 * size: 32 bits 263 * default: 0xFFFFFFFF 264 * There is one-to-one correspondence between the bits in this register and 265 * the Global Status register. 266 * If a mask bit is 0, the corresponding event causes an interrupt. 267 */ 268 269 270 #define ERI_G_MASK_TX_INT_ME (1 << 0) 271 /* 0 - set when a frame with INT_ME bit set is transferred to FIFO */ 272 #define ERI_G_MASK_TX_ALL (1 << 1) /* 1 - TX desc. ring empty */ 273 #define ERI_G_MASK_TX_DONE (1 << 2) /* 2 - from host to TX FIFO */ 274 #define ERI_G_MASK_RES1 (1 << 3) /* 3 - reserved */ 275 #define ERI_G_MASK_RX_DONE (1 << 4) /* 4 - from RXFIFO to host */ 276 #define ERI_G_MASK_RX_NO_BUF (1 << 5) /* 5 - no RX bufer available */ 277 #define ERI_G_MASK_RX_TAG_ERR (1 << 6) /* 6 - RX tag error */ 278 #define ERI_G_MASK_RES2 (0x3f << 7) /* 7-13 : reserved */ 279 #define ERI_G_MASK_PCS_INT (1 << 13) /* 13 - PCS Interrupt */ 280 #define ERI_G_MASK_TX_MAC_INT (1 << 14) /* 14 - TX MAC status reg set */ 281 #define ERI_G_MASK_RX_MAC_INT (1 << 15) /* 15 - RX MAC status reg set */ 282 #define ERI_G_MASK_MAC_CTRL_INT (1 << 16) /* 16 - MAC control reg set */ 283 #define ERI_G_MASK_MIF_INT (1 << 17) /* 17 - MIF status reg set */ 284 #define ERI_G_MASK_BUS_ERR_INT (1 << 18) /* 18 - BUS Error sts reg set */ 285 286 #define ERI_G_MASK_INTR (~ERI_G_STATUS_INTR | ERI_G_MASK_PCS_INT) 287 #define ERI_G_MASK_ALL (0xffffffffu) 288 289 290 /* 291 * Interrupt Ack Register (WO) 292 * Its layout corresponds to the layout of the top level bits of the Interrupt 293 * Status register. 294 * Bit positions written high will be cleared, while bit positions written low 295 * have no effect on the Interrupt Status Register. 296 */ 297 298 /* 299 * Status Register Alias (RO) 300 * This location presents the same view as the Interrupt Status Register, except 301 * that reading from this location does not automatically clear any of the 302 * register bits. 303 */ 304 305 /* 306 * PCI Error Status Register (R-AC) 307 * Other PCI bus errors : The specific error may be read from 308 * the PCI Status Register in PCI Configuration space 309 */ 310 #define ERI_G_STS_BADACK (1 << 0) /* no ACK64# during ABS64 */ 311 #define ERI_G_STS_DTRTO (1 << 1) /* Delayed trans timeout */ 312 #define ERI_G_STS_OTHERS (1 << 2) 313 314 /* 315 * PCI Error Mask Register (RW) 316 * size: 32 bits 317 * default: 0xffffffff 318 * Same layout as the PCI Error Status Register 319 */ 320 #define ERI_G_PCI_ERROR_MASK 0x00 321 322 /* 323 * BIF Configuration Register 324 * default: 0x0 325 * Used to configure specific system information for the BIF block to optimize. 326 * Default values indicate no special knowledge is assumed by BIF. 327 * M66EN is RO bit. 328 * 66 MHz operation (RO) May be used by the driver to sense 329 * whether ERI is operating in a 66MHz or 33 MHz PCI segment 330 */ 331 #define ERI_G_BIFCFG_SLOWCLK (1 << 0) /* for parity error timing */ 332 #define ERI_G_BIFCFG_HOST_64 (1 << 1) /* 64-bit host */ 333 #define ERI_G_BIFCFG_B64D_DIS (1 << 2) /* no 64-bit wide data */ 334 #define ERI_G_BIFCFG_M66EN (1 << 3) 335 336 /* 337 * BIF Diagnostic register (RW) 338 * TBD 339 */ 340 341 /* 342 * Global Software Reset Register - RW-AC 343 * The lower 2bits are used to perform an individual Software Reset to the 344 * TX or RX functions (when the corresponding bit is set), or 345 * a Global Software Reset to the ERI (when both bits are set). 346 * These bits become "self cleared" after the corresponding reset command 347 * has been executed. After a reset, the software must poll this register 348 * till both the bits are read as 0's. 349 * The third bit (RSTOUT) is not self clearing and is used to activate 350 * the RSTOUT# pin, when set. When clear, RSTOUT# follows the level of the 351 * PCI reset input pin. 352 */ 353 #define ERI_G_RESET_ETX (1 << 0) /* Reset ETX */ 354 #define ERI_G_RESET_ERX (1 << 1) /* Reset ERX */ 355 #define ERI_G_RESET_RSTOUT (1 << 2) /* force the RSTOUT# pin active */ 356 #define ERI_G_CACHE_BIT 16 357 #define ERI_G_CACHE_LINE_SIZE_16 16 /* cache line size of 64 bytes */ 358 #define ERI_G_CACHE_LINE_SIZE_32 32 /* cache line size of 128 bytes */ 359 #define ERI_G_CACHE_16 (ERI_G_CACHE_LINE_SIZE_16 << ERI_G_CACHE_BIT) 360 #define ERI_G_CACHE_32 (ERI_G_CACHE_LINE_SIZE_32 << ERI_G_CACHE_BIT) 361 362 #define ERI_G_RESET_GLOBAL (ERI_G_RESET_ETX | ERI_G_RESET_ERX) 363 364 /* 365 * Transmit DMA Register set 366 * tx_kick and tx_completion registers are set to 0 when ETX is reset. 367 */ 368 369 struct etx { 370 uint32_t tx_kick; /* 0x2000 RW Transmit Kick Register */ 371 uint32_t config; /* 0x2004 RW ETX Configuration Register */ 372 uint32_t txring_lo; /* 0x2008 RW Transmit Descriptor Base Low */ 373 uint32_t txring_hi; /* 0x200C RW Transmit Descriptor Base Low */ 374 uint32_t reserved1; /* 0x2010 */ 375 uint32_t txfifo_wr_ptr; /* 0x2014 RW TxFIFO Write Pointer */ 376 uint32_t txfifo_sdwr_ptr; /* 0x2018 RW TxFIFO Shadow Write Pointer */ 377 uint32_t txfifo_rd_ptr; /* 0x201C RW TxFIFO Read Pointer */ 378 uint32_t txfifo_sdrd_ptr; /* 0x2020 RW TxFIFO Shadow Read Pointer */ 379 uint32_t txfifo_pkt_cnt; /* 0x2024 RO TxFIFO Packet Counter */ 380 uint32_t state_mach; /* 0x2028 RO ETX State Machine Reg */ 381 uint32_t reserved2; /* 0x202C */ 382 uint32_t txdata_ptr_lo; /* 0x2030 RO ETX State Machine Register */ 383 uint32_t txdata_ptr_hi; /* 0x2034 RO ETX State Machine Register */ 384 uint32_t reserved3[50]; /* 0x2038 - 0x20FC */ 385 386 uint32_t tx_completion; /* 0x2100 RO ETX Completion Register */ 387 uint32_t txfifo_adrs; /* 0x2104 RW ETX FIFO address */ 388 uint32_t txfifo_tag; /* 0x2108 RO ETX FIFO tag */ 389 uint32_t txfifo_data_lo; /* 0x210C RW ETX FIFO data low */ 390 uint32_t txfifo_data_hi_T1; /* 0x2110 RW ETX FIFO data high T1 */ 391 uint32_t txfifo_data_hi_T0; /* 0x2114 RW ETX FIFO data high T0 */ 392 uint32_t txfifo_size; /* 0x2118 RO ETX FIFO size */ 393 394 uint32_t reserved4[964]; /* 0x211C - 0x3024 */ 395 396 uint32_t txdebug; /* 0x3028 RW ETX Debug Register */ 397 }; 398 399 400 /* 401 * TX Kick Register (RW) 402 * size: 13-bits 403 * default: 0x0 404 * Written by the host CPU with the descriptor value that follows the last 405 * valid Transmit descriptor. 406 */ 407 408 /* 409 * TX Completion Register 410 * size: 13-bits 411 * default: 0x0 412 * This register stores the descriptor value that follows the last descriptor 413 * already processed by ERI. 414 * 415 */ 416 #define ETX_COMPLETION_MASK 0x1fff 417 418 /* 419 * ETX Configuration Register 420 * default: 0x118010 421 * This register stores parameters that control the operation of the transmit 422 * DMA channel. 423 * If the desire is to buffer an entire standard Ethernet frame before its 424 * transmission is enabled, the Tx-FIFO-Threshold field has to be programmed 425 * to a value = > 0xC8. (CHECK). Default value is 0x460. 426 * Matewos: Changed the above to 0x400. Getting FIFO Underflow in the 427 * case if Giga bit speed. 428 * Bit 21 is used to modify the functionality of the Tx_All interrupt. 429 * If it is 0, Tx_All interrupt is generated after processing the last 430 * transmit descriptor. 431 * If it is 1, Tx_All interrupt is generated only after the entire 432 * Transmit FIFO has been drained. 433 */ 434 435 #define GET_CONFIG_TXDMA_EN (1 << 0) /* 0 - Enable Tx DMA */ 436 #define GET_CONFIG_TXRING_SZ (0xf << 1) /* 1-4:Tx desc ring size */ 437 #define GET_CONFIG_RESERVED (0x1f << 5) /* 5-9: Reserved */ 438 #define GET_CONFIG_TXFIFOTH (0x7ff << 10) /* 10-20 :TX FIFO Threshold */ 439 /* 440 * RIO specific value: TXFIFO threshold needs to be set to 1518/8. 441 * It was set to (0x4FF << 10) for GEM. 442 * set it back to 0x4ff. 443 * set it to 190 receive TXMAC underrun and hang 444 * try 0x100 445 * try 0x4ff 446 * try 0x100 447 */ 448 #define ETX_ERI_THRESHOLD 0x100 449 #define ETX_CONFIG_THRESHOLD (ETX_ERI_THRESHOLD << 10) 450 451 #define GET_CONFIG_PACED_MODE (1 << 21) /* 21 - TX_all_int mod */ 452 453 #define GET_CONFIG_THRESHOLD (0x400 << 10) /* For Ethernet Packets */ 454 #define GET_CONFIG_RINGSZ (ERI_TMDMAX << 1) /* for 2048 descriptors */ 455 /* 456 * ETX TX ring size 457 * This is a 4-bit value to determine the no. of descriptor entries in the 458 * TX-ring. The number of entries can vary from 32 through 8192 in multiples 459 * of 2. 460 */ 461 #define ERI_TX_RINGSZ_SHIFT 1 462 463 #define ETX_RINGSZ_32 0 464 #define ETX_RINGSZ_64 1 465 #define ETX_RINGSZ_128 2 466 #define ETX_RINGSZ_256 3 467 #define ETX_RINGSZ_512 4 468 #define ETX_RINGSZ_1024 5 469 #define ETX_RINGSZ_2048 6 470 #define ETX_RINGSZ_4096 7 471 #define ETX_RINGSZ_8192 8 472 /* values 9-15 are reserved. */ 473 474 /* 475 * Transmit Descriptor Base Low and High (RW) 476 * The 53 most significant bits are used as the base address for the TX 477 * descriptor ring. The 11 least significant bits are not stored and assumed 478 * to be 0. 479 * This register should be initialized to a 2KByte-aligned value after power-on 480 * or Software Reset. 481 */ 482 483 484 /* 485 * TX FIFO size (RO) 486 * This 11-bit RO register indicates the size, in 64 byte multiples, of the 487 * TX FIFO. 488 * The value of this register is 0x90, indicating a 9Kbyte TX FIFO. 489 */ 490 491 492 /* 493 * ERX Register Set 494 */ 495 496 struct erx { 497 uint32_t config; /* 0x4000 RW ERX Configuration Register */ 498 uint32_t rxring_lo; /* 0x4004 RW Receive Descriptor Base low */ 499 uint32_t rxring_hi; /* 0x4008 RW Receive Descriptor Base high */ 500 uint32_t rxfifo_wr_ptr; /* 0x400C RW RxFIFO Write Pointer */ 501 uint32_t rxfifo_sdwr_ptr; /* 0x4010 RW RxFIFO Shadow Write Pointer */ 502 uint32_t rxfifo_rd_ptr; /* 0x4014 RW RxFIFO Read pointer */ 503 uint32_t rxfifo_pkt_cnt; /* 0x4018 RO RxFIFO Packet Counter */ 504 uint32_t state_mach; /* 0x401C RO ERX State Machine Register */ 505 uint32_t rx_pause_threshold; /* 0x4020 RW ERX Pause thresholds */ 506 uint32_t rxdata_ptr_lo; /* 0x4024 RO ERX Data Pointer low */ 507 uint32_t rxdata_ptr_hi; /* 0x4028 RO ERX Data Pointer high */ 508 uint32_t reserved1[53]; /* 0x402C - 0x40FC */ 509 510 uint32_t rx_kick; /* 0x4100 RW ERX Kick Register */ 511 uint32_t rx_completion; /* 0x4104 RO ERX Completion Register */ 512 uint32_t rx_blanking; /* 0x4108 RO ERX Blanking Register */ 513 uint32_t rxfifo_adrs; /* 0x410C RW ERX FIFO address */ 514 uint32_t rxfifo_tag; /* 0x4110 RO ERX FIFO tag */ 515 uint32_t rxfifo_data_lo; /* 0x4114 RW ERX FIFO data low */ 516 uint32_t rxfifo_data_hi_T0; /* 0x4118 RW ERX FIFO data high T0 */ 517 uint32_t rxfifo_data_hi_T1; /* 0x411C RW ERX FIFO data high T1 */ 518 uint32_t rxfifo_size; /* 0x4120 RW ERX FIFO size */ 519 }; 520 521 /* 522 * ERX Configuration Register - RW 523 * This 27-bit register determines the ERX-specific parameters that control the 524 * operation of the receive DMA channel. 525 * Default : 0x1000010 526 */ 527 528 #define GET_CONFIG_RXDMA_EN (1 << 0) /* 0 : Enable Rx DMA */ 529 #define ERI_RX_CONFIG_RXRING_SZ (0xf << 1) /* 1-4 : RX ring size */ 530 #define ERI_RX_CONFIG_BATDIS (1 << 5) /* Disable RX desc batching */ 531 #define ERI_RX_CONFIG_RES1 (0xf << 6) /* 6-9 : reserverd */ 532 #define ERI_RX_CONFIG_FBOFFSET (0x7 << 10) /* 10-12 : 1st Byte Offset */ 533 #define ERI_RX_CONFIG_RX_CSSTART (0x7f << 13) /* 13-19:cksum start offset */ 534 #define ERI_RX_CONFIG_RES2 (0xf << 20) /* 20-23 : reserve */ 535 #define ERI_RX_CONFIG_RXFIFOTH (0x7 << 24) /* 24-26:RX DMA threshold */ 536 537 #define ERI_RX_RINGSZ_SHIFT 1 538 #define ERI_RX_CONFIG_FBO_SHIFT 10 539 #define ERI_RX_CONFIG_RX_CSSTART_SHIFT 13 540 #define ERI_RX_CONFIG_RXFIFOTH_SHIFT 24 541 542 #define ERX_RINGSZ_32 0 543 #define ERX_RINGSZ_64 1 544 #define ERX_RINGSZ_128 2 545 #define ERX_RINGSZ_256 3 546 #define ERX_RINGSZ_512 4 547 #define ERX_RINGSZ_1024 5 548 #define ERX_RINGSZ_2048 6 549 #define ERX_RINGSZ_4096 7 550 #define ERX_RINGSZ_8192 8 551 /* values 9-15 are reserved. */ 552 553 554 #define ERI_RX_FIFOTH_64 0 555 #define ERI_RX_FIFOTH_128 1 556 #define ERI_RX_FIFOTH_256 2 557 #define ERI_RX_FIFOTH_512 3 558 #define ERI_RX_FIFOTH_1024 4 559 #define ERI_RX_FIFOTH_2048 5 560 /* 6 & 7 are reserved values */ 561 562 /* 563 * Receive Descriptor Base Low and High (RW) 564 * The 53 most significant bits are used as the base address for the RX 565 * descriptor ring. The 11 least significant bits are not stored and assumed 566 * to be 0. 567 * This register should be initialized to a 2KByte-aligned value after power-on 568 * or Software Reset. 569 */ 570 571 572 /* 573 * Pause Thresholds Register (RW) 574 * default: 0x000f8 575 * Two PAUSE thresholds are used to define when PAUSE flow control frames are 576 * emitted by ERI. The granularity of these thresholds is in 64 byte increments. 577 * XOFF PAUSE frames use the pause_time value pre-programmed in the 578 * Send PAUSE MAC Register. 579 * XON PAUSE frames use a pause_time of 0. 580 */ 581 582 #define ERI_RX_PTH_OFFTH (0x1ff << 0) 583 /* 584 * 0-8: XOFF PAUSE emitted when RX FIFO 585 * occupancy rises above this value (times 64 bytes) 586 */ 587 #define ERI_RX_PTH_RES (0x7 << 9) /* 9-11: reserved */ 588 #define ERI_RX_PTH_ONTH (0x1ff << 12) 589 /* 590 * 12-20: XON PAUSE emitted when RX FIFO 591 * occupancy falls below this value (times 64 bytes) 592 */ 593 594 #define ERI_RX_PTH_ONTH_SHIFT 12 595 596 /* 597 * ------------------------------------------------------------------------ 598 * RX Kick Register (RW) 599 * This is a 13-bit register written by the host CPU. 600 * The last valid RX descriptor is the one right before the value of the 601 * register. 602 * Initially set to 0 on reset. 603 * RX descriptors must be posted in multiples of 4. 604 * The first descriptor should be cache-line aligned for best performance. 605 * ------------------------------------------------------------------------- 606 */ 607 608 /* 609 * RX Completion Register (RO) 610 * This 13-bit register indicates which descriptors are already used by ERI 611 * for receive frames. 612 * All descriptors upto but excluding the register value are ready to be 613 * processed by the host. 614 */ 615 616 /* 617 * RX Blanking Register (RW) 618 * Defines the values used for receive interrupt blanking. 619 * For INTR_TIME field, every count is 2048 PCI clock time. For 66 Mhz, each 620 * count is about 16 us. 621 */ 622 #define ERI_RX_BLNK_INTR_PACKETS (0x1ff << 0) 623 /* 624 * 0-8:no.of pkts to be recvd since the last RX_DONE 625 * interrupt, before a new interrupt 626 */ 627 #define ERI_RX_BLNK_RESERVED (0x7 << 9) /* 9-11 : reserved */ 628 #define ERI_RX_BLNK_INTR_TIME (0xff << 12) 629 /* 630 * 12-19 : no. of clocks to be counted since the last 631 * RX_DONE interrupt, before a new interrupt 632 */ 633 634 #define ERI_RX_BLNK_INTR_TIME_SHIFT 12 635 636 /* 637 * RX FIFO Size (RO) 638 * This 11-bit RO register indicates the size, in 64-bit multiples, of the 639 * RX FIFO. Software should use it to properly configure the PAUSE thresholds. 640 * The value read is 0x140, indicating a 20kbyte RX FIFO. 641 */ 642 643 644 /* 645 * Declarations and definitions specific to the ERI MAC functional block. 646 * 647 * The ERI MAC block will provide the MAC functons for 10 or 100 Mbps or 648 * 1 Gbps CSMA/CD-protocol-based or full-duplex interface. 649 */ 650 651 /* 652 * ERI MAC Register Set. 653 * ERI MAC addresses map on a word boundry. So all registers are 654 * declared for a size of 32 bits. Registers that use fewer than 32 655 * bits will return 0 in the bits not used. 656 * TBD: Define the constant values which should be used for initializing 657 * these registers. 658 */ 659 struct bmac { 660 uint32_t txrst; /* 0x6000 tx software reset (RW) */ 661 uint32_t rxrst; /* 0x6004 rx software reset Reg (RW) */ 662 uint32_t spcmd; /* 0x6008 Send Pause Command Reg (RW) */ 663 uint32_t res1; /* 0x600C reserved */ 664 uint32_t txsts; /* 0x6010 tx MAC status reg (R-AC) */ 665 uint32_t rxsts; /* 0x6014 rx MAC status reg (R-AC) */ 666 uint32_t macctl_sts; /* 0x6018 MAC Control Stat Reg (R-AC) */ 667 uint32_t res2; /* 0x601C reserved */ 668 uint32_t txmask; /* 0x6020 tx MAC Mask Register (RW) */ 669 uint32_t rxmask; /* 0x6024 rx MAC Mask register (RW) */ 670 uint32_t macctl_mask; /* 0x6028 MAC Control Mask Reg (RW) */ 671 uint32_t res3; /* 0x602C reserved */ 672 uint32_t txcfg; /* 0x6030 tx config reg [8-0] (RW) */ 673 uint32_t rxcfg; /* 0x6034 rx config reg [7-0] (RW) */ 674 uint32_t macctl_cfg; /* 0x6038 MAC Control Config Reg (RW) */ 675 uint32_t xifc; /* 0x603C XIF Config. reg [7-0] (RW) */ 676 uint32_t ipg0; /* 0x6040 Inter pkt Gap 0 [7-0] (RW) */ 677 uint32_t ipg1; /* 0x6044 Inter pkt Gap 1 [7-0] (RW) */ 678 uint32_t ipg2; /* 0x6048 Inter pkt Gap 2 [7-0] (RW) */ 679 uint32_t slot; /* 0x604C slot time reg [7-0] (RW) */ 680 uint32_t macmin; /* 0x6050 MAC min frame sze [9-0](RW) */ 681 uint32_t macmax; /* 0x6054 MAC max pkt sze [14-0] (RW) */ 682 uint32_t palen; /* 0x6058 preamble len reg [9-0] (RW) */ 683 uint32_t jam; /* 0x605C jam size reg [3-0] (RW) */ 684 uint32_t alimit; /* 0x6060 attempt limit reg [7-0](RW) */ 685 uint32_t macctl_type; /* 0x6064 MAC Control Type Reg (RW) */ 686 uint32_t res4[6]; /* reserved 0x6068 - 0x607C */ 687 uint32_t madd0; /* 0x6080 Norm MAC adrs 0 [15-0] (RW) */ 688 uint32_t madd1; /* 0x6084 Norm MAC adrs 1 [31-16](RW) */ 689 uint32_t madd2; /* 0x6088 Norm MAC adrs 2 [47-32](RW) */ 690 uint32_t madd3; /* 0x608C Alt. MAC adrs 0 [15-0](RW) */ 691 uint32_t madd4; /* 0x6090 Alt. MAC adrs 1 [31-16](RW) */ 692 uint32_t madd5; /* 0x6094 Alt. MAC adrs 2 [47-32](RW) */ 693 uint32_t madd6; /* 0x6098 Control MAC adrs 0 [15-0](RW) */ 694 uint32_t madd7; /* 0x609C Control MAC adrs 1 [31-16](RW) */ 695 uint32_t madd8; /* 0x60A0 Control MAC adrs 2 [47-32](RW) */ 696 uint32_t afr0; /* 0x60A4 addr filt reg 0_0 [15-0](RW) */ 697 uint32_t afr1; /* 0x60A8 addr filt reg 0_1 [15-0](RW) */ 698 uint32_t afr2; /* 0x60AC addr filt reg 0_2 [15-0](RW) */ 699 uint32_t afmr1_2; /* 0x60B0 addr filt msk reg 1,2 [8-0](RW) */ 700 uint32_t afmr0; /* 0x60B4 addr filt msk reg 0 [15-0](RW) */ 701 uint32_t res5[2]; /* 0x60B8 - 0x60BC Reserved */ 702 uint32_t hash0; /* 0x60C0 h-table 0 [15-0] (RW) */ 703 uint32_t hash1; /* 0x60C4 h-table 1 [31-16] (RW) */ 704 uint32_t hash2; /* 0x60C8 h-table 2 [47-32] (RW) */ 705 uint32_t hash3; /* 0x60CC h-table 3 [63-48] (RW) */ 706 uint32_t hash4; /* 0x60D0 h-table 4 [79-64] (RW) */ 707 uint32_t hash5; /* 0x60D4 h-table 5 [95-80] (RW) */ 708 uint32_t hash6; /* 0x60D8 h-table 6 [111-96] (RW) */ 709 uint32_t hash7; /* 0x60DC h-table 7 [127-112] (RW) */ 710 uint32_t hash8; /* 0x60E0 h-table 8 [143-128] (RW) */ 711 uint32_t hash9; /* 0x60E4 h-table 9 [159-144] (RW) */ 712 uint32_t hash10; /* 0x60E8 h-table 10 [175-160] (RW) */ 713 uint32_t hash11; /* 0x60EC h-table 11 [191-176] (RW) */ 714 uint32_t hash12; /* 0x60F0 h-table 12 [207-192] (RW) */ 715 uint32_t hash13; /* 0x60F4 h-table 13 [223-208] (RW) */ 716 uint32_t hash14; /* 0x60F8 h-table 14 [239-224] (RW) */ 717 uint32_t hash15; /* 0x60FC h-table 15 [255-240] (RW) */ 718 uint32_t nccnt; /* 0x6100 normal coll cnt [15-0] (RW) */ 719 uint32_t fccnt; /* 0x6104 1st succes coll [15-0] (RW) */ 720 uint32_t excnt; /* 0x6108 excess coll cnt[15-0] (RW) */ 721 uint32_t ltcnt; /* 0x610C late coll cnt [15-0] (RW) */ 722 uint32_t dcnt; /* 0x6110 defer timer cnt [15-0] (RW) */ 723 uint32_t pattempts; /* 0x6114 peak attempt reg [7-0] (RW) */ 724 uint32_t frcnt; /* 0x6118 rcv frame cnt [15-0] (RW) */ 725 uint32_t lecnt; /* 0x611C rx len err cnt [15-0] (RW) */ 726 uint32_t aecnt; /* 0x6120 rx align err cnt[15-0] (RW) */ 727 uint32_t fecnt; /* 0x6124 rcv crc err cnt [15-0] (RW) */ 728 uint32_t rxcv; /* 0x6128 rx code viol reg [15-0](RW) */ 729 uint32_t res6; /* 0x612C Reserved */ 730 uint32_t rseed; /* 0x6130 random num seed [9-0] (RW) */ 731 uint32_t macsm; /* 0x6134 MAC state mach reg [7-0](R) */ 732 }; 733 734 #define BMAC_OVERFLOW_STATE 0x03800000 735 736 /* 737 * Constants used for initializing the MAC registers 738 */ 739 740 #define BMAC_SEND_PAUSE_CMD 0x1BF0 741 #define BMAC_IPG0 0x00 742 #define BMAC_IPG1 0x08 743 #define BMAC_IPG2 0x04 744 #define BMAC_SLOT_TIME 0x40 745 #define BMAC_EXT_SLOT_TIME 0x200 746 #define BMAC_MIN_FRAME_SIZE 0x40 747 #define BMAC_MAX_FRAME_SIZE (ETHERMTU + 18 + 4) /* enet + vlan */ 748 749 /* 750 * Hardware bug: set MAC_FRAME_SIZE to 0x7fff to 751 * get around the problem of tag errors 752 */ 753 #ifdef ERI_RX_TAG_ERROR_WORKAROUND 754 #define BMAC_MAX_FRAME_SIZE_TAG 0x7fff 755 #endif 756 757 #define BMAC_MAX_BURST (0x2000 << 16) 758 #define BMAC_PREAMBLE_SIZE 0x07 759 #define BMAC_JAM_SIZE 0x04 760 #define BMAC_ATTEMPT_LIMIT 0x10 761 #define BMAC_CONTROL_TYPE 0x8808 762 #define BMAC_ADDRESS_3 0x0000 763 #define BMAC_ADDRESS_4 0x0000 764 #define BMAC_ADDRESS_5 0x0000 765 #define BMAC_ADDRESS_6 0x0001 766 #define BMAC_ADDRESS_7 0xC200 767 #define BMAC_ADDRESS_8 0x0180 768 #define BMAC_AF_0 0x0000 769 #define BMAC_AF_1 0x0000 770 #define BMAC_AF_2 0x0000 771 #define BMAC_AF21_MASK 0x00 772 #define BMAC_AF0_MASK 0x0000 773 #define BMAC_COUNTER 0x0000 /* for all MAC Counters */ 774 775 /* 776 * ERI MAC Register Bit Masks. 777 */ 778 779 /* 780 * TX_MAC Software Reset Command Register (RW) 781 * This bit is set to 1 when a PIO write is done. This bit becomes self-cleared. 782 * after the command has been executed. 783 */ 784 785 #define BMAC_TX_RESET (1 << 0) /* TX_MAC Reset Command */ 786 787 788 /* 789 * RX_MAC Software Reset Command Register (RW) 790 * This bit is set to 1 when a PIO write is done. This bit becomes self-cleared. 791 * after the command has been executed. 792 */ 793 794 #define BMAC_RX_RESET (1 << 0) /* RX_MAC Reset Command */ 795 796 /* 797 * Send Pause Command Register (RW) 798 * This command register executes a Pause Flow Control frame transmission. 799 * Pause_Time_Sent field indicates to the MAC the value of the pause_time 800 * operand that should be sent on the network using either the Send_Pause 801 * Command bit or the flow control handshake on the RxDMA < - > MAC interface. 802 * The pause-time is interpreted in terms of Slot times. 803 */ 804 805 /* 806 * 0-15: value of pause_time operand 807 * in terms of slot time 808 */ 809 810 #define ERI_MCTLSP_TIME (0xffff << 0) 811 #define ERI_MCTLSP_SEND (1 << 16) /* send Pause flow control frame */ 812 813 814 /* 815 * TX_MAC Status Register (R-AC) 816 */ 817 818 #define BMAC_TXSTS_XMIT_DONE (1 << 0) /* Frame transmitted */ 819 #define BMAC_TXSTS_TX_URUN (1 << 1) /* TX MAC Underrun */ 820 #define BMAC_TXSTS_MAXPKT_ERR (1 << 2) /* packet len exceeds max len */ 821 #define BMAC_TXSTS_NCC_EXP (1 << 3) /* Normal Collision cnt exp */ 822 #define BMAC_TXSTS_ECC_EXP (1 << 4) /* Excess Collision cnt exp */ 823 #define BMAC_TXSTS_LCC_EXP (1 << 5) /* Late Collision cnt exp */ 824 #define BMAC_TXSTS_FCC_EXP (1 << 6) /* First Collision cnt exp */ 825 #define BMAC_TXSTS_DEFER_EXP (1 << 7) /* Defer Timer exp */ 826 #define BMAC_TXSTS_PEAK_EXP (1 << 8) /* Peak attempts cnt exp */ 827 828 /* 829 * TX_MAC Mask Register (RW) 830 */ 831 832 #define BMAC_TXMASK_XMIT_DONE (1 << 0) /* Frame transmitted */ 833 #define BMAC_TXMASK_TX_URUN (1 << 1) /* TX MAC Underrun */ 834 #define BMAC_TXMASK_MAXPKT_ERR (1 << 2) /* packet len exceeds max len */ 835 #define BMAC_TXMASK_NCC_EXP (1 << 3) /* Normal Collision cnt exp */ 836 #define BMAC_TXMASK_ECC_EXP (1 << 4) /* Excess Collision cnt exp */ 837 #define BMAC_TXMASK_LCC_EXP (1 << 5) /* Late Collision cnt exp */ 838 #define BMAC_TXMASK_FCC_EXP (1 << 6) /* First Collision cnt exp */ 839 #define BMAC_TXMASK_DEFER_EXP (1 << 7) /* Defer Timer exp */ 840 #define BMAC_TXMASK_PEAK_EXP (1 << 8) /* Peak attempts cnt exp */ 841 /* Matewos added defer counter */ 842 #define BMAC_TXINTR_MASK (BMAC_TXMASK_XMIT_DONE | BMAC_TXMASK_DEFER_EXP) 843 844 /* 845 * RX_MAC Status Register (R-AC) 846 */ 847 #define BMAC_RXSTS_RX_DONE (1 << 0) /* Frame Received */ 848 #define BMAC_RXSTS_RX_OVF (1 << 1) /* RX MAC data path overflow */ 849 #define BMAC_RXSTS_FRMCNT_EXP (1 << 2) /* RX Frame counter exp */ 850 #define BMAC_RXSTS_ALE_EXP (1 << 3) /* RX Alignment error cnt exp */ 851 #define BMAC_RXSTS_CRC_EXP (1 << 4) /* RX CRC error cnt exp */ 852 #define BMAC_RXSTS_LEN_EXP (1 << 5) /* RX Length error cnt exp */ 853 #define BMAC_RXSTS_CVI_EXP (1 << 6) /* RX Code violate err cnt exp */ 854 855 /* 856 * RX_MAC Mask Register (R-AC) 857 */ 858 #define BMAC_RXMASK_RX_DONE (1 << 0) /* Frame Received */ 859 #define BMAC_RXMASK_RX_OVF (1 << 1) /* RX MAC data path overflow */ 860 #define BMAC_RXMASK_FRMCNT_EXP (1 << 2) /* RX Frame counter exp */ 861 #define BMAC_RXMASK_ALE_EXP (1 << 3) /* RX Alignment error cnt exp */ 862 #define BMAC_RXMASK_CRC_EXP (1 << 4) /* RX CRC error cnt exp */ 863 #define BMAC_RXMASK_LEN_EXP (1 << 5) /* RX Length error cnt exp */ 864 #define BMAC_RXMASK_CVI_EXP (1 << 6) /* RX Code violate err cnt exp */ 865 866 #define BMAC_RXINTR_MASK (BMAC_RXMASK_RX_DONE | BMAC_RXMASK_FRMCNT_EXP) 867 868 /* 869 * MAC Control Status Register (R-AC) 870 */ 871 #define ERI_MCTLSTS_PAUSE_RCVD (1 << 0) /* PAUSE received */ 872 #define ERI_MCTLSTS_PAUSE_STATE (1 << 1) /* transition to PAUSE state */ 873 #define ERI_MCTLSTS_NONPAUSE (1 << 2) /* change to non-PAUSE state */ 874 #define ERI_MCTLSTS_RESERVED (0x1fff << 3) /* 3-15: reserved */ 875 #define ERI_MCTLSTS_PAUSE_TIME (0xffff0000) /* 16-31: Pause time recvd */ 876 877 #define ERI_MCTLSTS_PAUSE_TIME_SHIFT 16 878 879 /* 880 * MAC Control Mask Register (RW) 881 * pause time is in slot-time units. 882 */ 883 #define ERI_MCTLMASK_PAUSE_RCVD (1 << 0) /* PAUSE received */ 884 #define ERI_MCTLMASK_PAUSE_STATE (1 << 1) /* transition to PAUSE state */ 885 #define ERI_MCTLMASK_NONPAUSE (1 << 2) /* change to non-PAUSE state */ 886 #define ERI_MCTLMASK_RESERVED (0x1fff << 3) /* 3-15: reserved */ 887 #define ERI_MCTLMASK_PAUSE_TIME (0xffff << 16) /* 16-31: Pause time recvd */ 888 889 #define ERI_MACCTL_INTR_MASK 0x00000000 890 891 /* 892 * XIF Configuration Register 893 * This register determines the parameters that control the operation of the 894 * transceiver interface. 895 * The Disable-echo bit should be 0 for full-duplex mode. 896 * Default: 0x00 897 */ 898 899 #define BMAC_XIFC_TX_MII_OE (1 << 0) /* Enable XIF output drivers */ 900 #define BMAC_XIFC_MIILPBK (1 << 1) /* Enable MII Loopback mode */ 901 #define BMAC_XIFC_DIS_ECHO (1 << 2) /* Disable echo */ 902 #define BMAC_XIFC_MII_MODE (1 << 3) /* Selects GMII/MII mode */ 903 #define BMAC_XIFC_MIIBUF_OE (1 << 4) /* Enable MII Recv Buffers */ 904 #define BMAC_XIFC_LINK_LED (1 << 5) /* force LINKLED# active */ 905 #define BMAC_XIFC_FDPLX_LED (1 << 6) /* force FDPLXLED# active */ 906 907 /* 908 * TX_MAC Configuration Register 909 * Ignore_Carrier_Sense should be set to 1 for full-duplex operation and 910 * cleared to 0 for half-duplex operation.. 911 * Ignore_collisions should be set to 1 for full-duplex operation and cleared 912 * to 0 for half-duplex operation.. 913 * To Ensure proper operation of the TX_MAC, the TX_MAC_Enable bit must always 914 * be cleared to 0 and a delay imposed before a PIO write to any of the other 915 * bits in the TX_MAC Configuration register or any of the MAC parameter 916 * registers is done. 917 * The amount of delay required depends on the time required to transmit a max. 918 * size frame. 919 * Default: TBD 920 */ 921 922 #define BMACTXRSTDELAY (125) /* 125 us wait period */ 923 /* CHECK */ 924 925 #define BMAC_TXCFG_ENAB (1 << 0) /* tx enable */ 926 #define BMAC_TXCFG_IGNCS (1 << 1) /* Ignore carrier sense */ 927 #define BMAC_TXCFG_IGCOLL (1 << 2) /* Ignore collisions */ 928 #define BMAC_TXCFG_ENIPG0 (1 << 3) /* Extend Rx-to-Tx IPG */ 929 #define BMAC_TXCFG_NGU (1 << 4) /* Never Give Up */ 930 #define BMAC_TXCFG_NGU_LIMIT (1 << 5) /* Never Give Up limit */ 931 #define BMAC_TXCFG_NBKOFF (1 << 6) /* No Backoff */ 932 #define BMAC_TXCFG_SLOWDOWN (1 << 7) /* Slow down */ 933 #define BMAC_TXCFG_NFCS (1 << 8) /* no FCS will be generated */ 934 #define BMAC_TXCFG_CARR_EXT (1 << 9) 935 /* 936 * Enable TX Carrier Extension Carrier Extension is 937 * required for half-duplex operation at Gbps 938 */ 939 940 #define BMAC_TXCFG_FDX (BMAC_TXCFG_IGNCS | BMAC_TXCFG_IGCOLL) 941 942 /* 943 * RX_MAC Configuration Register 944 * A delay of 3.2 ms should be allowed after clearing Rx_MAC_Enable or 945 * Hash_Filter_enable or Address_Filter_Enable bits. 946 * Default: TBD 947 */ 948 /* CHECK 3ms or us */ 949 /* GEM specification: 3.2msec (3200 usec) */ 950 951 #define BMACRXRSTDELAY (3200) /* 3.2 ms wait period */ 952 953 #define BMAC_RXCFG_ENAB (1 << 0) /* rx enable */ 954 #define BMAC_RXCFG_STRIP_PAD (1 << 1) /* rx strip pad bytes */ 955 #define BMAC_RXCFG_STRIP_CRC (1 << 2) /* rx enable CRC stripping */ 956 #define BMAC_RXCFG_PROMIS (1 << 3) /* rx enable promiscous */ 957 #define BMAC_RXCFG_GRPROM (1 << 4) /* rx promiscuous group mode */ 958 #define BMAC_RXCFG_HASH (1 << 5) /* rx enable hash filter */ 959 #define BMAC_RXCFG_ADDR (1 << 6) /* rx enable address filter */ 960 #define BMAC_RXCFG_ERR (1 << 7) /* rx disable error checking */ 961 #define BMAC_RXCFG_CARR_EXT (1 << 8) 962 /* 963 * Enable RX Carrier Extension. 964 * Enables the reception of packet bursts 965 * generated by Carrier Extension with 966 * packet bursting senders 967 */ 968 969 /* 970 * MAC Control Configuration Register (RW) 971 * Default: 0x00 972 */ 973 974 #define ERI_MCTLCFG_TXPAUSE (1 << 0) /* Send_PAUSE Enable */ 975 #define ERI_MCTLCFG_RXPAUSE (1 << 1) /* Receive_PAUSE Enable */ 976 #define ERI_MCTLCFG_PASSPAUSE (1 << 2) /* Pass PAUSE up */ 977 978 /* 979 * MAC Control Type Register (RW) 980 * This 16-bit register specifies the "type" field for the MAC Control frame. 981 * Default: 0x8808 982 */ 983 984 985 /* 986 * MAC Address Registers 0, 1, 2 987 * Station's Normal peririty MAC address which must be a unicast address. 988 * 0 - [15:0], 1 - [31:16], 2 - [47:32] 989 */ 990 991 /* 992 * MAC Address Registers 3, 4, 5 993 * Station's Alternate MAC address which may be a unicast or multicast address. 994 * 3 - [15:0], 4 - [31:16], 5 - [47:32] 995 */ 996 997 /* 998 * MAC Address Registers 6, 7, 8 999 * Station's Control MAC address which must be the reserved multicast 1000 * address for MAC Control frames. 1001 * 6 - [15:0], 7 - [31:16], 8 - [47:32] 1002 */ 1003 1004 /* 1005 * MII Transceiver Interface 1006 * 1007 * The Management Interface (MIF) allows the host to program and collect status 1008 * from two transceivers connected to the MII. MIF supports three modes of 1009 * operation: 1010 * 1. Bit-Bang Mode 1011 * This mode is imlemented using three 1-bit registers: data, clock, 1012 * and output_enable. 1013 * 1014 * 2. Frame Mode 1015 * This mode is supported using one 32-bit register: Frame register. 1016 * The software loads the Frame Register with avalid instaruction 1017 * ("frame"), and polls the Valid Bit for completion. 1018 * 1019 * 3. Polling Mode 1020 * The Polling mechanism is used for detecting a status change in the 1021 * transceiver. When this mode is enabled, the MIF will continuously 1022 * poll a specified transceiver register and generate a maskable 1023 * interrupt when a status change is detected. This mode of operation 1024 * can only be used when the MIF is in the "Frame mode". 1025 * 1026 */ 1027 1028 struct mif { 1029 uint32_t mif_bbclk; /* 0x6200 (RW) MIF Bit Bang Clock */ 1030 uint32_t mif_bbdata; /* 0x6204 (RW) MIF Bit Bang Data */ 1031 uint32_t mif_bbopenb; /* 0x6208 (RW) MIF Bit Bang Output Enable */ 1032 uint32_t mif_frame; /* 0x620C (RW) MIF Frame - ctl and data */ 1033 uint32_t mif_cfg; /* 0x6210 (RW) MIF Configuration */ 1034 uint32_t mif_imask; /* 0x6214 (RW) MIF Interrupt mask */ 1035 uint32_t mif_bsts; /* 0x6218 (R-AC) MIF Basic/Status register */ 1036 uint32_t mif_fsm; /* 0x621C (RO) MIF State machine register */ 1037 }; 1038 1039 /* 1040 * mif_bbclk - Bit Bang Clock register 1041 */ 1042 #define ERI_MIF_BBCLK (1 << 0); /* Bit Babg Clock */ 1043 1044 #define ERI_BBCLK_LOW 0 1045 #define ERI_BBCLK_HIGH 1 1046 1047 /* mif_bbdata - bit Bang Data register */ 1048 #define ERI_MIF_BBDATA (1 << 0); /* Bit Bang Data */ 1049 1050 /* mif_bbopenb - Bit Bang oOutput Enable register */ 1051 #define ERI_MIF_BBOPENB (1 << 0); /* Bit Bang output Enable */ 1052 1053 /* 1054 * Management Frame Structure: 1055 * <IDLE> <ST><OP><PHYAD><REGAD><TA> <DATA> <IDLE> 1056 * READ: <01><10><AAAAA><RRRRR><Z0><DDDDDDDDDDDDDDDD> 1057 * WRITE: <01><01><AAAAA><RRRRR><10><DDDDDDDDDDDDDDDD> 1058 */ 1059 1060 /* 1061 * mif_frame - MIF control and data register 1062 */ 1063 #define ERI_MIF_FRDATA (0xffff << 0) /* 0-15 : data bits */ 1064 #define ERI_MIF_FRTA0 (0x1 << 16) /* 16 : TA bit, 1 for completion */ 1065 #define ERI_MIF_FRTA1 (0x1 << 17) /* 16-17 : TA bits */ 1066 #define ERI_MIF_FRREGAD (0x1f << 18) /* 18-22 : register address bits */ 1067 #define ERI_MIF_FRPHYAD (0x1f << 23) /* 23-27 : PHY ad, should be 0 */ 1068 #define ERI_MIF_FROP (0x3 << 28) /* 28-29 : Operation - Write/Read */ 1069 #define ERI_MIF_FRST (0xc0000000) /* 30-31 : START bits */ 1070 1071 #define ERI_MIF_FRREGAD_SHIFT 18 1072 #define ERI_MIF_FRPHYAD_SHIFT 23 1073 #define ERI_MIF_FRREAD 0x60020000 1074 #define ERI_MIF_FRWRITE 0x50020000 1075 1076 /* 1077 * maximum delay for MIF Register Read/Write operation 1078 */ 1079 #define ERI_MAX_MIF_DELAY (100) 1080 1081 /* 1082 * maximum delay for Transceiver Reset 1083 */ 1084 #define ERI_PHYRST_MAXDELAY (500) 1085 #define ERI_PCS_PHYRST_MAXDELAY (500) 1086 1087 /* 1088 * mif_cfg - MIF Configuration Register 1089 */ 1090 #define ERI_MIF_CFGPS (1 << 0) /* PHY Select */ 1091 #define ERI_MIF_CFGPE (1 << 1) /* Poll Enable */ 1092 #define ERI_MIF_CFGBB (1 << 2) /* Bit Bang Enable */ 1093 #define ERI_MIF_CFGPR (0x1f << 3) /* Poll Register address */ 1094 #define ERI_MIF_CFGM0 (1 << 8) /* MDIO_0 Data / MDIO_0 attached */ 1095 #define ERI_MIF_CFGM1 (1 << 9) /* MDIO_1 Data / MDIO_1 attached */ 1096 #define ERI_MIF_CFGPD (0x1f << 10) /* Poll Device PHY address */ 1097 1098 #define ERI_MIF_CFGPR_SHIFT 3 1099 #define ERI_MIF_CFGPD_SHIFT 10 1100 #define ERI_MIF_POLL_DELAY 200 1101 1102 /* 1103 * MDIO_0 corresponds to the On Board Transceiver. 1104 * MDIO_1 corresponds to the External Transceiver. 1105 * The PHYAD for both is 0. 1106 */ 1107 #define ERI_INTERNAL_PHYAD 1 /* PHY address for int. transceiver */ 1108 #define ERI_EXTERNAL_PHYAD 0 /* PHY address for ext. transceiver */ 1109 #define ERI_NOXCVR_PHYAD 99 /* PHY address for no transceiver */ 1110 1111 1112 /* mif_imask - MIF Interrupt Mask Register */ 1113 /* 1114 * This register is bit-to-bit same as Basic/Status Register 1115 */ 1116 #define ERI_MIF_INTMASK (0xffff << 0) /* 0-15 : Interrupt mask */ 1117 1118 /* mif_bassts - MIF Basic - Status register */ 1119 /* 1120 * The Basic portion of this register indicates the last value of the register 1121 * read indicated in the POLL REG field of the Configuration Register. 1122 * The Status portion indicates bit(s) that have changed. 1123 * The MIF Mask register is corresponding to this register in terms of the 1124 * bit(s) that need to be masked for generating interrupt on the MIF Interrupt 1125 * Bit of the Global Status Rgister. 1126 */ 1127 1128 #define ERI_MIF_STATUS (0xffff << 0) /* 0-15 : Status */ 1129 #define ERI_MIF_BASIC (0xffff << 16) /* 16-31 : Basic register */ 1130 1131 /* mif_fsm - MIF State Machine register */ 1132 1133 #define ERI_MIF_FSM (0x3ff << 0) /* 0-9 : MIF state */ 1134 1135 /* 1136 * ERI PCS/Serial-Link 1137 */ 1138 struct pcslink { 1139 uint32_t pcs_ctl; /* 0x9000 (RW) PCS MII Control Reg */ 1140 uint32_t pcs_sts; /* 0x9004 (RO) PCS MII Status Register */ 1141 uint32_t pcs_anar; /* 0x9008 (RW) PCS MII Avertisement Reg */ 1142 uint32_t pcs_anlpar; /* 0x900C (RW) PCS MII LP Ability Reg */ 1143 uint32_t pcs_cfg; /* 0x9010 (RW) PCS Configuration Register */ 1144 uint32_t pcs_smr; /* 0x9014 (RW) PCS State Machine Reg */ 1145 uint32_t pcs_intsts; /* 0x9018 (R-AC) PCS Interrupt Status Reg */ 1146 uint32_t res1[13]; /* 0x901C - 0x904C Reserved */ 1147 uint32_t pcs_dmode; /* 0x9050 (RW) Datapath mode register */ 1148 uint32_t slink_ctl; /* 0x9054 (RW) Serial Link Control register */ 1149 uint32_t pcs_opsel; /* 0x9058 (RW) Shared Output Select register */ 1150 uint32_t slink_sts; /* 0x905C (RO) Serial Link Status register */ 1151 }; 1152 1153 /* 1154 * PCS MII Basic Mode Control Register 1155 * Auto-Negotiation should always be used for 802.3z 8B/10B 1156 * link configuration. May be cleared for diagnostic purposes, or 1157 * as a workaround for possible early product interoperability problems. 1158 */ 1159 1160 #define PCS_BMCR_RESET (1 << 15) /* Resets the PCS when set */ 1161 #define PCS_BMCR_LPBK (1 << 14) /* Loopback of the 10-bit i/f */ 1162 #define PCS_BMCR_1000M (1 << 13) /* Speed selection, always 0 */ 1163 #define PCS_BMCR_ANE (1 << 12) /* Auto Negotiation Enabled when set */ 1164 #define PCS_BMCR_PWRDN (1 << 11) /* Power down, always 0 */ 1165 #define PCS_BMCR_ISOLATE (1 << 10) /* Isolate PHY from MII, always 0 */ 1166 #define PCS_BMCR_RAN (1 << 9) /* Set to Restart Auto Negotiation */ 1167 #define PCS_BMCR_FDX (1 << 8) /* Full Duplex, always 0 */ 1168 #define PCS_BMCR_COLTST (1 << 7) /* Collision Test */ 1169 #define PCS_BMCR_RES1 (0x7f << 0) /* 0-6 Reserved */ 1170 1171 #define PCS_AUTONEG_DISABLE 0 1172 1173 /* 1174 * ------------------------------------------------------------------------ 1175 * PCS MII Basic Mode Status Register 1176 * ------------------------------------------------------------------------- 1177 */ 1178 1179 1180 #define PCS_BMSR_RES2 (0x1f << 11) /* 11-15 reserved, always 0 */ 1181 #define PCS_BMSR_GBFDX (1 << 10) /* PCS able to perform GBit FDX */ 1182 #define PCS_BMSR_GBHDX (1 << 9) /* PCS able to perform Gbit HDX */ 1183 #define PCS_BMSR_RES1 (0x7 << 6) /* 6-8 reserved */ 1184 #define PCS_BMSR_ANC (1 << 5) /* Auto Negotiation Completed */ 1185 #define PCS_BMSR_REMFLT (1 << 4) /* Remote Fault detected */ 1186 #define PCS_BMSR_ACFG (1 << 3) /* Able to do Auto Link Negotiation,1 */ 1187 #define PCS_BMSR_LNKSTS (1 << 2) /* Link Status */ 1188 #define PCS_BMSR_JABDET (1 << 1) /* Jabber Condition Detected, 0 */ 1189 #define PCS_BMSR_EXTCAP (1 << 0) /* Extended Register Capability, 0 */ 1190 1191 #define PCS_CAPABILITY_MASK (PCS_BMSR_GBFDX | PCS_BMSR_GBHDX) 1192 1193 1194 /* 1195 * ------------------------------------------------------------------------ 1196 * PCS MII Auto-Negotiation Advertisement Register (nway1Reg) 1197 * This register will hold the different modes of operation to be advertised to 1198 * the far-end PHY. 1199 * ------------------------------------------------------------------------- 1200 */ 1201 1202 #define PCS_ANAR_NP (1 << 15) /* Next Page bit, RO, always 0 */ 1203 #define PCS_ANAR_ACK (1 << 14) /* Acks reception of Link Partner */ 1204 /* Capability word */ 1205 #define PCS_ANAR_RF (0x2 << 12) /* Advertise Remote Fault det. cap. */ 1206 #define PCS_ANAR_RES1 (0x7 << 9) /* 9-11 reserved */ 1207 #define PCS_ANAR_PTX (1 << 8) /* Pause TX */ 1208 #define PCS_ANAR_PRX (1 << 7) /* Pause RX */ 1209 #define PCS_ANAR_PAUSE (1 << 7) /* Pause */ 1210 #define PCS_ANAR_ASM_DIR (1 << 8) /* Asymetric Direction */ 1211 #define PCS_ANAR_GBFDX (1 << 5) /* Advertise Gbit FDX Capability */ 1212 #define PCS_ANAR_GBHDX (1 << 6) /* Advertise Gbit HDX Capability */ 1213 #define PCS_ANAR_RES (0x1f << 0) /* 0-5 Reserved */ 1214 1215 1216 /* ************************************************************************ */ 1217 /* 1218 * PCS MII Auto-Negotiation Link Partner Ability Reg 1219 * This register contains the Link Partners capabilities after NWay 1220 * Auto-Negotiation is complete. 1221 */ 1222 1223 #define PCS_ANLPAR_NP (1 << 15) /* Next Page bit, RO, always 0 */ 1224 #define PCS_ANLPAR_ACK (1 << 14) /* Acks reception of Link Partner */ 1225 /* Capability word */ 1226 #define PCS_ANLPAR_RF (0x2 << 12) /* Advertise Remote Fault det. cap. */ 1227 #define PCS_ANLPAR_RES1 (0x7 << 9) /* 9-11 reserved */ 1228 #define PCS_ANLPAR_PTX (1 << 8) /* Pause TX */ 1229 #define PCS_ANLPAR_PRX (1 << 7) /* Pause RX */ 1230 #define PCS_ANLPAR_GBFDX (1 << 5) /* Advertise Gbit FDX Capability */ 1231 #define PCS_ANLPAR_GBHDX (1 << 6) /* Advertise Gbit HDX Capability */ 1232 #define PCS_ANLPAR_RES (0x1f << 0) /* 0-5 Reserved */ 1233 1234 1235 /* 1236 * ------------------------------------------------------------------------ 1237 * PCS Configuration Register 1238 * Default = 0x8 1239 * ------------------------------------------------------------------------- 1240 */ 1241 1242 #define PCS_CFG_RES (0xfff << 4) /* 4-15 Reserved */ 1243 #define PCS_CFG_TIMER (0x7 << 1) 1244 /* Timer values used for the 802.3z Clause 36 Link Monitor s/m timers */ 1245 #define PCS_CFG_ENABLE (1 << 0) /* Enable PCS, when set to 1 */ 1246 1247 1248 /* 1249 * ------------------------------------------------------------------------ 1250 * PCS Interrupt State Register 1251 * Presently only one bit is implemented, reflecting transitions on the link 1252 * status. Note that there is no mask register at this level. 1253 * THe PCS_INT bit may be masked at the Interrupt Status Register level. 1254 * ------------------------------------------------------------------------- 1255 */ 1256 1257 #define PCS_STS_LNKSTS 2 /* Link Status Change */ 1258 1259 1260 /* 1261 * ------------------------------------------------------------------------ 1262 * Datapath Mode Register (RW) 1263 * This register controls which network interface is used. 1264 * Only one bit should be set in this register. 1265 * Default: 0x1 1266 * ------------------------------------------------------------------------- 1267 */ 1268 /* 1269 * Select MII/GMII and not PCS. 1270 * Selection between MII and GMII is 1271 * controlled by the XIF register 1272 */ 1273 #define ERI_PCS_MII (1 << 2) 1274 /* 1275 * Applicable only in Serial Mode 1276 * When set, makes the 10-bit Xmit data 1277 * visible at the GMII 1278 */ 1279 #define ERI_PCS_GMIIOUTEN (1 << 3) 1280 1281 1282 /* 1283 * ------------------------------------------------------------------------ 1284 * Serial Link Control register (RW) 1285 * This register controls the Serial link 1286 * Default: 0x000 1287 * ------------------------------------------------------------------------- 1288 */ 1289 #define ERI_SLC_LOOPBACK (1 << 0) /* Enables loopback at the SL o/p */ 1290 #define ERI_SLC_ENSYNCDT (1 << 1) /* Enable Sync char detection */ 1291 #define ERI_SLC_LOCKREF (1 << 2) /* Lock to reference clock */ 1292 #define ERI_SLC_EMP (0x2 << 3) /* Control o/p driver emphasis */ 1293 #define ERI_SLC_RES (1 << 5) /* Reserved */ 1294 #define ERI_SLC_SELFTEST (0x7 << 6) /* To select built-in self tests */ 1295 #define ERI_SLC_SW_PDOWN (1 << 9) /* Power down Serial link block */ 1296 1297 /* 1298 * ------------------------------------------------------------------------ 1299 * Shared Output Select Register (RW) 1300 * Default: 0x00 1301 * ------------------------------------------------------------------------- 1302 */ 1303 1304 /* 1305 * ------------------------------------------------------------------------ 1306 * Serial Link State Register (RO) 1307 * Indicates the progress of the Serial link boot up 1308 * 00 - Undergoing test 1309 * 01 - Waiting 500us while lockrefn is asserted 1310 * 10 - Waiting for comma detect 1311 * 11 - Receive Data is synchronized 1312 * ------------------------------------------------------------------------- 1313 */ 1314 #define ERI_SLS_STATE (0x2 << 0) /* state */ 1315 1316 1317 1318 /* ************************************************************************ */ 1319 /* 1320 * Definition for the time required to wait after a software 1321 * reset has been issued. 1322 */ 1323 #define ERI_MAX_RST_DELAY (200) 1324 #define ERI_PERIOD (20) /* period to wait */ 1325 #define ERI_WAITPERIOD ERI_PERIOD 1326 1327 #define ERI_DELAY(c, n) \ 1328 { \ 1329 register int N = n / ERI_WAITPERIOD; \ 1330 while (--N > 0) { \ 1331 if (c) \ 1332 break; \ 1333 drv_usecwait(ERI_WAITPERIOD); \ 1334 } \ 1335 } 1336 1337 #define MIF_ERIDELAY(n, phyad, regad) \ 1338 { \ 1339 register int N = n / ERI_WAITPERIOD; \ 1340 PUT_MIFREG(mif_frame, \ 1341 (ERI_MIF_FRREAD | (phyad << ERI_MIF_FRPHYAD_SHIFT) | \ 1342 (regad << ERI_MIF_FRREGAD_SHIFT))); \ 1343 while (--N > 0) { \ 1344 if (GET_MIFREG(mif_frame) & ERI_MIF_FRTA0) \ 1345 break; \ 1346 drv_usecwait(ERI_WAITPERIOD); \ 1347 } \ 1348 } 1349 1350 1351 #ifdef __cplusplus 1352 } 1353 #endif 1354 1355 #endif /* _SYS_ERI_MAC_H */ 1356