xref: /titanic_52/usr/src/uts/common/io/pcic.c (revision 9512fe850e98fdd448c638ca63fdd92a8a510255)
1 /*
2  * CDDL HEADER START
3  *
4  * The contents of this file are subject to the terms of the
5  * Common Development and Distribution License (the "License").
6  * You may not use this file except in compliance with the License.
7  *
8  * You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE
9  * or http://www.opensolaris.org/os/licensing.
10  * See the License for the specific language governing permissions
11  * and limitations under the License.
12  *
13  * When distributing Covered Code, include this CDDL HEADER in each
14  * file and include the License file at usr/src/OPENSOLARIS.LICENSE.
15  * If applicable, add the following below this CDDL HEADER, with the
16  * fields enclosed by brackets "[]" replaced with your own identifying
17  * information: Portions Copyright [yyyy] [name of copyright owner]
18  *
19  * CDDL HEADER END
20  */
21 
22 /*
23  * Copyright 2006 Sun Microsystems, Inc.  All rights reserved.
24  * Use is subject to license terms.
25  */
26 
27 #pragma ident	"%Z%%M%	%I%	%E% SMI"
28 
29 /*
30  * PCIC device/interrupt handler
31  *	The "pcic" driver handles the Intel 82365SL, Cirrus Logic
32  *	and Toshiba (and possibly other clones) PCMCIA adapter chip
33  *	sets.  It implements a subset of Socket Services as defined
34  *	in the Solaris PCMCIA design documents
35  */
36 
37 /*
38  * currently defined "properties"
39  *
40  * clock-frequency		bus clock frequency
41  * smi				system management interrupt override
42  * need-mult-irq		need status IRQ for each pair of sockets
43  * disable-audio		don't route audio signal to speaker
44  */
45 
46 
47 #include <sys/types.h>
48 #include <sys/inttypes.h>
49 #include <sys/param.h>
50 #include <sys/systm.h>
51 #include <sys/user.h>
52 #include <sys/buf.h>
53 #include <sys/file.h>
54 #include <sys/uio.h>
55 #include <sys/conf.h>
56 #include <sys/stat.h>
57 #include <sys/autoconf.h>
58 #include <sys/vtoc.h>
59 #include <sys/dkio.h>
60 #include <sys/ddi.h>
61 #include <sys/sunddi.h>
62 #include <sys/sunndi.h>
63 #include <sys/var.h>
64 #include <sys/callb.h>
65 #include <sys/open.h>
66 #include <sys/ddidmareq.h>
67 #include <sys/dma_engine.h>
68 #include <sys/kstat.h>
69 #include <sys/kmem.h>
70 #include <sys/modctl.h>
71 #include <sys/pci.h>
72 #include <sys/pci_impl.h>
73 
74 #include <sys/pctypes.h>
75 #include <sys/pcmcia.h>
76 #include <sys/sservice.h>
77 
78 #include <sys/note.h>
79 
80 #include <sys/pcic_reg.h>
81 #include <sys/pcic_var.h>
82 
83 #if defined(__sparc)
84 #include <sys/pci/pci_nexus.h>
85 #endif
86 
87 #include <sys/hotplug/hpcsvc.h>
88 #include <sys/syshw.h>
89 #include "cardbus/cardbus.h"
90 
91 #define	SOFTC_SIZE	(sizeof (anp_t))
92 
93 static int pcic_getinfo(dev_info_t *, ddi_info_cmd_t, void *, void **);
94 static int pcic_attach(dev_info_t *, ddi_attach_cmd_t);
95 static int pcic_detach(dev_info_t *, ddi_detach_cmd_t);
96 static uint_t pcic_intr(caddr_t, caddr_t);
97 static int pcic_do_io_intr(pcicdev_t *, uint32_t);
98 static int pcic_probe(dev_info_t *);
99 
100 static int pcic_open(dev_t *, int, int, cred_t *);
101 static int pcic_close(dev_t, int, int, cred_t *);
102 static int pcic_ioctl(dev_t, int, intptr_t, int, cred_t *, int *);
103 
104 typedef struct pcm_regs pcm_regs_t;
105 
106 static void pcic_init_assigned(dev_info_t *);
107 static int pcic_apply_avail_ranges(dev_info_t *, pcm_regs_t *,
108 	pci_regspec_t *, int);
109 int pci_resource_setup_avail(dev_info_t *, pci_regspec_t *, int);
110 
111 /*
112  * On x86 platforms the ddi_iobp_alloc(9F) and ddi_mem_alloc(9F) calls
113  * are xlated into DMA ctlops. To make this nexus work on x86, we
114  * need to have the default ddi_dma_mctl ctlops in the bus_ops
115  * structure, just to pass the request to the parent. The correct
116  * ctlops should be ddi_no_dma_mctl because so far we don't do DMA.
117  */
118 static
119 struct bus_ops pcmciabus_ops = {
120 	BUSO_REV,
121 	pcmcia_bus_map,
122 	NULL,
123 	NULL,
124 	NULL,
125 	i_ddi_map_fault,
126 	ddi_no_dma_map,
127 	ddi_no_dma_allochdl,
128 	ddi_no_dma_freehdl,
129 	ddi_no_dma_bindhdl,
130 	ddi_no_dma_unbindhdl,
131 	ddi_no_dma_flush,
132 	ddi_no_dma_win,
133 	ddi_dma_mctl,
134 	pcmcia_ctlops,
135 	pcmcia_prop_op,
136 	NULL,				/* (*bus_get_eventcookie)();	*/
137 	NULL,				/* (*bus_add_eventcall)();	*/
138 	NULL,				/* (*bus_remove_eventcall)();	*/
139 	NULL,				/* (*bus_post_event)();		*/
140 	NULL,				/* (*bus_intr_ctl)();		*/
141 	NULL,				/* (*bus_config)(); 		*/
142 	NULL,				/* (*bus_unconfig)(); 		*/
143 	NULL,				/* (*bus_fm_init)(); 		*/
144 	NULL,				/* (*bus_fm_fini)(); 		*/
145 	NULL,				/* (*bus_enter)()		*/
146 	NULL,				/* (*bus_exit)()		*/
147 	NULL,				/* (*bus_power)()		*/
148 	pcmcia_intr_ops			/* (*bus_intr_op)(); 		*/
149 };
150 
151 static struct cb_ops pcic_cbops = {
152 	pcic_open,
153 	pcic_close,
154 	nodev,
155 	nodev,
156 	nodev,
157 	nodev,
158 	nodev,
159 	pcic_ioctl,
160 	nodev,
161 	nodev,
162 	nodev,
163 	nochpoll,
164 	ddi_prop_op,
165 	NULL,
166 #ifdef CARDBUS
167 	D_NEW | D_MP | D_HOTPLUG
168 #else
169 	D_NEW | D_MP
170 #endif
171 };
172 
173 static struct dev_ops pcic_devops = {
174 	DEVO_REV,
175 	0,
176 	pcic_getinfo,
177 	nulldev,
178 	pcic_probe,
179 	pcic_attach,
180 	pcic_detach,
181 	nulldev,
182 	&pcic_cbops,
183 	&pcmciabus_ops,
184 	NULL
185 };
186 
187 void *pcic_soft_state_p = NULL;
188 static int pcic_maxinst = -1;
189 static timeout_id_t pcic_delayed_resume_toid;
190 
191 int pcic_do_insertion = 1;
192 int pcic_do_removal = 1;
193 
194 struct irqmap {
195 	int irq;
196 	int count;
197 } pcic_irq_map[16];
198 
199 
200 int pcic_debug = 0x0;
201 static  void    pcic_err(dev_info_t *dip, int level, const char *fmt, ...);
202 extern void cardbus_dump_pci_config(dev_info_t *dip);
203 extern void cardbus_dump_socket(dev_info_t *dip);
204 extern int cardbus_validate_iline(dev_info_t *dip, ddi_acc_handle_t handle);
205 static void pcic_dump_debqueue(char *msg);
206 
207 #if defined(PCIC_DEBUG)
208 static void xxdmp_all_regs(pcicdev_t *, int, uint32_t);
209 
210 #define	pcic_mutex_enter(a)	\
211 	{ \
212 		pcic_err(NULL, 10, "Set lock at %d\n", __LINE__); \
213 		mutex_enter(a); \
214 	};
215 
216 #define	pcic_mutex_exit(a)	\
217 	{ \
218 		pcic_err(NULL, 10, "Clear lock at %d\n", __LINE__); \
219 		mutex_exit(a); \
220 	};
221 
222 #else
223 #define	pcic_mutex_enter(a)	mutex_enter(a)
224 #define	pcic_mutex_exit(a)	mutex_exit(a)
225 #endif
226 
227 #define	PCIC_VCC_3VLEVEL	1
228 #define	PCIC_VCC_5VLEVEL	2
229 #define	PCIC_VCC_12LEVEL	3
230 
231 /* bit patterns to select voltage levels */
232 int pcic_vpp_levels[13] = {
233 	0, 0, 0,
234 	1,	/* 3.3V */
235 	0,
236 	1,	/* 5V */
237 	0, 0, 0, 0, 0, 0,
238 	2	/* 12V */
239 };
240 
241 uint8_t pcic_cbv_levels[13] = {
242 	0, 0, 0,
243 	3,			/* 3.3V */
244 	0,
245 	2,			/* 5V */
246 	0, 0, 0, 0, 0, 0,
247 	1			/* 12V */
248 };
249 
250 struct power_entry pcic_power[4] = {
251 	{
252 		0, VCC|VPP1|VPP2
253 	},
254 	{
255 		33,		/* 3.3Volt */
256 		VCC|VPP1|VPP2
257 	},
258 	{
259 		5*10,		/* 5Volt */
260 		VCC|VPP1|VPP2	/* currently only know about this */
261 	},
262 	{
263 		12*10,		/* 12Volt */
264 		VPP1|VPP2
265 	}
266 };
267 
268 /*
269  * Base used to allocate ranges of PCI memory on x86 systems
270  * Each instance gets a chunk above the base that is used to map
271  * in the memory and I/O windows for that device.
272  * Pages below the base are also allocated for the EXCA registers,
273  * one per instance.
274  */
275 #define	PCIC_PCI_MEMCHUNK	0x1000000
276 
277 static int pcic_wait_insert_time = 5000000;	/* In micro-seconds */
278 static int pcic_debounce_time = 200000; /* In micro-seconds */
279 
280 struct debounce {
281 	pcic_socket_t *pcs;
282 	clock_t expire;
283 	struct debounce *next;
284 };
285 
286 static syshw_t pcic_syshw = {
287 	0, "PC Card Socket 0", SH_CONNECTION,
288 	SYSHW_CAN_SIGNAL_CHANGE|SYSHW_STATE_VALID|SYSHW_VAL0_VALID,
289 	B_FALSE, {2, 0, 0, 0}
290 };
291 
292 static struct debounce *pcic_deb_queue = NULL;
293 static kmutex_t pcic_deb_mtx;
294 static kcondvar_t pcic_deb_cv;
295 static kthread_t *pcic_deb_threadid;
296 
297 static inthandler_t *pcic_handlers;
298 
299 static void pcic_setup_adapter(pcicdev_t *);
300 static int pcic_change(pcicdev_t *, int);
301 static int pcic_ll_reset(pcicdev_t *, int);
302 static void pcic_mswait(pcicdev_t *, int, int);
303 static boolean_t pcic_check_ready(pcicdev_t *, int);
304 static void pcic_set_cdtimers(pcicdev_t *, int, uint32_t, int);
305 static void pcic_ready_wait(pcicdev_t *, int);
306 extern int pcmcia_get_intr(dev_info_t *, int);
307 extern int pcmcia_return_intr(dev_info_t *, int);
308 
309 static int pcic_callback(dev_info_t *, int (*)(), int);
310 static int pcic_inquire_adapter(dev_info_t *, inquire_adapter_t *);
311 static int pcic_get_adapter(dev_info_t *, get_adapter_t *);
312 static int pcic_get_page(dev_info_t *, get_page_t *);
313 static int pcic_get_socket(dev_info_t *, get_socket_t *);
314 static int pcic_get_status(dev_info_t *, get_ss_status_t *);
315 static int pcic_get_window(dev_info_t *, get_window_t *);
316 static int pcic_inquire_socket(dev_info_t *, inquire_socket_t *);
317 static int pcic_inquire_window(dev_info_t *, inquire_window_t *);
318 static int pcic_reset_socket(dev_info_t *, int, int);
319 static int pcic_set_page(dev_info_t *, set_page_t *);
320 static int pcic_set_window(dev_info_t *, set_window_t *);
321 static int pcic_set_socket(dev_info_t *, set_socket_t *);
322 static int pcic_set_interrupt(dev_info_t *, set_irq_handler_t *);
323 static int pcic_clear_interrupt(dev_info_t *, clear_irq_handler_t *);
324 static void pcic_pm_detection(void *);
325 static void pcic_iomem_pci_ctl(ddi_acc_handle_t, uchar_t *, unsigned);
326 static int clext_reg_read(pcicdev_t *, int, uchar_t);
327 static void clext_reg_write(pcicdev_t *, int, uchar_t, uchar_t);
328 static int pcic_calc_speed(pcicdev_t *, uint32_t);
329 static int pcic_card_state(pcicdev_t *, pcic_socket_t *);
330 static int pcic_find_pci_type(pcicdev_t *);
331 static void pcic_82092_smiirq_ctl(pcicdev_t *, int, int, int);
332 static void pcic_handle_cd_change(pcicdev_t *, pcic_socket_t *, uint8_t);
333 static uint_t pcic_cd_softint(caddr_t, caddr_t);
334 static uint8_t pcic_getb(pcicdev_t *, int, int);
335 static void pcic_putb(pcicdev_t *, int, int, int8_t);
336 static int pcic_set_vcc_level(pcicdev_t *, set_socket_t *);
337 static uint_t pcic_softintr(caddr_t, caddr_t);
338 
339 static void pcic_debounce(pcic_socket_t *);
340 static void pcic_delayed_resume(void *);
341 static void *pcic_add_debqueue(pcic_socket_t *, int);
342 static void pcic_rm_debqueue(void *);
343 static void pcic_deb_thread();
344 
345 static boolean_t pcic_load_cardbus(pcicdev_t *pcic, const pcic_socket_t *sockp);
346 static void pcic_unload_cardbus(pcicdev_t *pcic, const pcic_socket_t *sockp);
347 static uint32_t pcic_getcb(pcicdev_t *pcic, int reg);
348 static void pcic_putcb(pcicdev_t *pcic, int reg, uint32_t value);
349 static void pcic_cb_enable_intr(dev_info_t *);
350 static void pcic_cb_disable_intr(dev_info_t *);
351 static void pcic_enable_io_intr(pcicdev_t *pcic, int socket, int irq);
352 static void pcic_disable_io_intr(pcicdev_t *pcic, int socket);
353 
354 static cb_nexus_cb_t pcic_cbnexus_ops = {
355 	pcic_cb_enable_intr,
356 	pcic_cb_disable_intr
357 };
358 
359 static int pcic_exca_powerctl(pcicdev_t *pcic, int socket, int powerlevel);
360 static int pcic_cbus_powerctl(pcicdev_t *pcic, int socket);
361 
362 static void pcic_syshw_cardstate(syshw_t *, void *);
363 
364 #if defined(__sparc)
365 static int pcic_fault(enum pci_fault_ops op, void *arg);
366 #endif
367 
368 /*
369  * Default to support for Voyager IIi if sparc is defined.
370  * Appart from the PCI base addresses this only effect the TI1250.
371  */
372 #if defined(sparc)
373 #define	VOYAGER
374 #endif
375 
376 
377 /*
378  * pcmcia_attach() uses 0 and 128 upwards for the initpcmcia and devctl
379  * interfaces so we use 254.
380  */
381 #define	SYSHW_MINOR	254
382 
383 /*
384  * Forward declarations for syshw interface (See end of file).
385  */
386 static void syshw_attach(pcicdev_t *);
387 static void syshw_detach(pcicdev_t *);
388 static void syshw_resume(pcicdev_t *);
389 
390 #ifdef VOYAGER
391 static uint_t syshw_intr(caddr_t);
392 static uint_t syshw_intr_hi(pcicdev_t *);
393 #endif
394 
395 static int syshw_open(dev_t *, int, int, cred_t *);
396 static int syshw_close(dev_t, int, int, cred_t *);
397 static int syshw_ioctl(dev_t, int, intptr_t, int, cred_t *, int *);
398 static uint32_t syshw_add2map(syshw_t *, void (*)(syshw_t *, void *), void *);
399 static void syshw_send_signal(int);
400 
401 /*
402  * pcmcia interface operations structure
403  * this is the private interface that is exported to the nexus
404  */
405 pcmcia_if_t pcic_if_ops = {
406 	PCIF_MAGIC,
407 	PCIF_VERSION,
408 	pcic_callback,
409 	pcic_get_adapter,
410 	pcic_get_page,
411 	pcic_get_socket,
412 	pcic_get_status,
413 	pcic_get_window,
414 	pcic_inquire_adapter,
415 	pcic_inquire_socket,
416 	pcic_inquire_window,
417 	pcic_reset_socket,
418 	pcic_set_page,
419 	pcic_set_window,
420 	pcic_set_socket,
421 	pcic_set_interrupt,
422 	pcic_clear_interrupt,
423 	NULL,
424 };
425 
426 /*
427  * chip type identification routines
428  * this list of functions is searched until one of them succeeds
429  * or all fail.  i82365SL is assumed if failed.
430  */
431 static int pcic_ci_cirrus(pcicdev_t *);
432 static int pcic_ci_vadem(pcicdev_t *);
433 static int pcic_ci_ricoh(pcicdev_t *);
434 
435 int (*pcic_ci_funcs[])(pcicdev_t *) = {
436 	pcic_ci_cirrus,
437 	pcic_ci_vadem,
438 	pcic_ci_ricoh,
439 	NULL
440 };
441 
442 static struct modldrv modldrv = {
443 	&mod_driverops,		/* Type of module. This one is a driver */
444 	"PCIC PCMCIA adapter driver %I%",	/* Name of the module. */
445 	&pcic_devops,		/* driver ops */
446 };
447 
448 static struct modlinkage modlinkage = {
449 	MODREV_1, (void *)&modldrv, NULL
450 };
451 
452 int
453 _init()
454 {
455 	int stat;
456 
457 	/* Allocate soft state */
458 	if ((stat = ddi_soft_state_init(&pcic_soft_state_p,
459 	    SOFTC_SIZE, 2)) != DDI_SUCCESS)
460 		return (stat);
461 
462 	if ((stat = mod_install(&modlinkage)) != 0)
463 		ddi_soft_state_fini(&pcic_soft_state_p);
464 
465 	return (stat);
466 }
467 
468 int
469 _fini()
470 {
471 	int stat = 0;
472 
473 	if ((stat = mod_remove(&modlinkage)) != 0)
474 		return (stat);
475 
476 	if (pcic_deb_threadid) {
477 		mutex_enter(&pcic_deb_mtx);
478 		pcic_deb_threadid = 0;
479 		while (!pcic_deb_threadid)
480 			cv_wait(&pcic_deb_cv, &pcic_deb_mtx);
481 		pcic_deb_threadid = 0;
482 		mutex_exit(&pcic_deb_mtx);
483 
484 		mutex_destroy(&pcic_deb_mtx);
485 		cv_destroy(&pcic_deb_cv);
486 	}
487 
488 	ddi_soft_state_fini(&pcic_soft_state_p);
489 
490 	return (stat);
491 }
492 
493 int
494 _info(struct modinfo *modinfop)
495 {
496 	return (mod_info(&modlinkage, modinfop));
497 }
498 
499 /*
500  * pcic_getinfo()
501  *	provide instance/device information about driver
502  */
503 /*ARGSUSED*/
504 static int
505 pcic_getinfo(dev_info_t *dip, ddi_info_cmd_t cmd, void *arg, void **result)
506 {
507 	anp_t *anp;
508 	int error = DDI_SUCCESS;
509 	minor_t minor;
510 
511 	switch (cmd) {
512 	    case DDI_INFO_DEVT2DEVINFO:
513 		minor = getminor((dev_t)arg);
514 		if (minor == SYSHW_MINOR)
515 			minor = 0;
516 		else
517 			minor &= 0x7f;
518 		if (!(anp = ddi_get_soft_state(pcic_soft_state_p, minor)))
519 			*result = NULL;
520 		else
521 			*result = anp->an_dip;
522 		break;
523 	    case DDI_INFO_DEVT2INSTANCE:
524 		minor = getminor((dev_t)arg);
525 		if (minor == SYSHW_MINOR)
526 			minor = 0;
527 		else
528 			minor &= 0x7f;
529 		*result = (void *)((long)minor);
530 		break;
531 	    default:
532 		error = DDI_FAILURE;
533 		break;
534 	}
535 	return (error);
536 }
537 
538 static int
539 pcic_probe(dev_info_t *dip)
540 {
541 	int value;
542 	ddi_device_acc_attr_t attr;
543 	ddi_acc_handle_t handle;
544 	uchar_t *index, *data;
545 
546 	if (ddi_dev_is_sid(dip) == DDI_SUCCESS)
547 	    return (DDI_PROBE_DONTCARE);
548 
549 	/*
550 	 * find a PCIC device (any vendor)
551 	 * while there can be up to 4 such devices in
552 	 * a system, we currently only look for 1
553 	 * per probe.  There will be up to 2 chips per
554 	 * instance since they share I/O space
555 	 */
556 	attr.devacc_attr_version = DDI_DEVICE_ATTR_V0;
557 	attr.devacc_attr_endian_flags = DDI_NEVERSWAP_ACC;
558 	attr.devacc_attr_dataorder = DDI_STRICTORDER_ACC;
559 
560 	if (ddi_regs_map_setup(dip, PCIC_ISA_CONTROL_REG_NUM,
561 				(caddr_t *)&index,
562 				PCIC_ISA_CONTROL_REG_OFFSET,
563 				PCIC_ISA_CONTROL_REG_LENGTH,
564 				&attr, &handle) != DDI_SUCCESS)
565 	    return (DDI_PROBE_FAILURE);
566 
567 	data = index + 1;
568 
569 #if defined(PCIC_DEBUG)
570 	if (pcic_debug)
571 		cmn_err(CE_CONT, "pcic_probe: entered\n");
572 	if (pcic_debug)
573 		cmn_err(CE_CONT, "\tindex=%p\n", (void *)index);
574 #endif
575 	ddi_put8(handle, index, PCIC_CHIP_REVISION);
576 	ddi_put8(handle, data, 0);
577 	value = ddi_get8(handle, data);
578 #if defined(PCIC_DEBUG)
579 	if (pcic_debug)
580 		cmn_err(CE_CONT, "\tchip revision register = %x\n", value);
581 #endif
582 	if ((value & PCIC_REV_MASK) >= PCIC_REV_LEVEL_LOW &&
583 	    (value & 0x30) == 0) {
584 		/*
585 		 * we probably have a PCIC chip in the system
586 		 * do a little more checking.  If we find one,
587 		 * reset everything in case of softboot
588 		 */
589 		ddi_put8(handle, index, PCIC_MAPPING_ENABLE);
590 		ddi_put8(handle, data, 0);
591 		value = ddi_get8(handle, data);
592 #if defined(PCIC_DEBUG)
593 		if (pcic_debug)
594 			cmn_err(CE_CONT, "\tzero test = %x\n", value);
595 #endif
596 		/* should read back as zero */
597 		if (value == 0) {
598 			/*
599 			 * we do have one and it is off the bus
600 			 */
601 #if defined(PCIC_DEBUG)
602 			if (pcic_debug)
603 				cmn_err(CE_CONT, "pcic_probe: success\n");
604 #endif
605 			ddi_regs_map_free(&handle);
606 			return (DDI_PROBE_SUCCESS);
607 		}
608 	}
609 #if defined(PCIC_DEBUG)
610 	if (pcic_debug)
611 		cmn_err(CE_CONT, "pcic_probe: failed\n");
612 #endif
613 	ddi_regs_map_free(&handle);
614 	return (DDI_PROBE_FAILURE);
615 }
616 
617 /*
618  * These are just defaults they can also be changed via a property in the
619  * conf file.
620  */
621 static int pci_config_reg_num = PCIC_PCI_CONFIG_REG_NUM;
622 static int pci_control_reg_num = PCIC_PCI_CONTROL_REG_NUM;
623 static int pcic_do_pcmcia_sr = 0;
624 static int pcic_use_cbpwrctl = PCF_CBPWRCTL;
625 
626 /*
627  * enable insertion/removal interrupt for 32bit cards
628  */
629 static int
630 cardbus_enable_cd_intr(dev_info_t *dip)
631 {
632 	ddi_acc_handle_t	iohandle;
633 	caddr_t	ioaddr;
634 	ddi_device_acc_attr_t attr;
635 	attr.devacc_attr_version = DDI_DEVICE_ATTR_V0;
636 	attr.devacc_attr_endian_flags = DDI_STRUCTURE_LE_ACC;
637 	attr.devacc_attr_dataorder = DDI_STRICTORDER_ACC;
638 	(void) ddi_regs_map_setup(dip, 1,
639 				(caddr_t *)&ioaddr,
640 				0,
641 				4096,
642 				&attr, &iohandle);
643 
644 	/* CSC Interrupt: Card detect interrupt on */
645 	ddi_put32(iohandle, (uint32_t *)(ioaddr+CB_STATUS_MASK),
646 		ddi_get32(iohandle,
647 		(uint32_t *)(ioaddr+CB_STATUS_MASK)) | CB_SE_CCDMASK);
648 
649 	ddi_put32(iohandle, (uint32_t *)(ioaddr+CB_STATUS_EVENT),
650 		ddi_get32(iohandle, (uint32_t *)(ioaddr+CB_STATUS_EVENT)));
651 
652 	ddi_regs_map_free(&iohandle);
653 	return (1);
654 }
655 
656 /*
657  * pcic_attach()
658  *	attach the PCIC (Intel 82365SL/CirrusLogic/Toshiba) driver
659  *	to the system.  This is a child of "sysbus" since that is where
660  *	the hardware lives, but it provides services to the "pcmcia"
661  *	nexus driver.  It gives a pointer back via its private data
662  *	structure which contains both the dip and socket services entry
663  *	points
664  */
665 static int
666 pcic_attach(dev_info_t *dip, ddi_attach_cmd_t cmd)
667 {
668 	anp_t *pcic_nexus;
669 	pcicdev_t *pcic;
670 	int irqlevel, value;
671 	int pci_cfrn, pci_ctrn;
672 	int i, j, smi, actual;
673 	char *typename;
674 	char bus_type[16] = "(unknown)";
675 	int len = sizeof (bus_type);
676 	ddi_device_acc_attr_t attr;
677 	anp_t *anp = ddi_get_driver_private(dip);
678 	uint_t	pri;
679 	syshw_t *shwp;
680 
681 #if defined(PCIC_DEBUG)
682 	if (pcic_debug) {
683 		cmn_err(CE_CONT, "pcic_attach: entered\n");
684 	}
685 #endif
686 	switch (cmd) {
687 	case DDI_ATTACH:
688 		break;
689 	case DDI_RESUME:
690 		pcic = anp->an_private;
691 		/*
692 		 * for now, this is a simulated resume.
693 		 * a real one may need different things.
694 		 */
695 		if (pcic != NULL && pcic->pc_flags & PCF_SUSPENDED) {
696 			mutex_enter(&pcic->pc_lock);
697 			/* should probe for new sockets showing up */
698 			pcic_setup_adapter(pcic);
699 			syshw_resume(pcic);
700 			pcic->pc_flags &= ~PCF_SUSPENDED;
701 			mutex_exit(&pcic->pc_lock);
702 			(void) pcmcia_begin_resume(dip);
703 			/*
704 			 * this will do the CARD_INSERTION
705 			 * due to needing time for threads to
706 			 * run, it must be delayed for a short amount
707 			 * of time.  pcmcia_wait_insert checks for all
708 			 * children to be removed and then triggers insert.
709 			 */
710 			/*
711 			 * The reason for having a single timeout here
712 			 * rather than seperate timeout()s for each instance
713 			 * is due to the limited number (2) of callout threads
714 			 * available in Solaris 2.6. A single 1250A ends up
715 			 * as two instances of the interface with one slot each.
716 			 * The pcic_delayed_resume() function ends by calling
717 			 * pcmcia_wait_insert() which at one point does a
718 			 * delay(). delay() is implemented with a timeout()
719 			 * call so you end up with both the callout()
720 			 * threads waiting to be woken up by another callout().
721 			 * This situation locks up the machine hence the
722 			 * convolution here to only use one timeout.
723 			 */
724 			if (!pcic_delayed_resume_toid)
725 				pcic_delayed_resume_toid =
726 				    timeout(pcic_delayed_resume, (caddr_t)0,
727 				    drv_usectohz(pcic_wait_insert_time));
728 
729 			/*
730 			 * for complete implementation need END_RESUME (later)
731 			 */
732 			return (DDI_SUCCESS);
733 
734 		}
735 		return (DDI_SUCCESS);
736 	default:
737 		return (DDI_FAILURE);
738 	}
739 
740 	/*
741 	 * Allocate soft state associated with this instance.
742 	 */
743 	if (ddi_soft_state_zalloc(pcic_soft_state_p,
744 				ddi_get_instance(dip)) != DDI_SUCCESS) {
745 		cmn_err(CE_CONT, "pcic%d: Unable to alloc state\n",
746 			ddi_get_instance(dip));
747 		return (DDI_FAILURE);
748 	}
749 
750 	pcic_nexus = ddi_get_soft_state(pcic_soft_state_p,
751 	    ddi_get_instance(dip));
752 
753 	pcic = kmem_zalloc(sizeof (pcicdev_t), KM_SLEEP);
754 
755 	pcic->dip = dip;
756 	pcic_nexus->an_dip = dip;
757 	pcic_nexus->an_if = &pcic_if_ops;
758 	pcic_nexus->an_private = pcic;
759 	pcic->pc_numpower = sizeof (pcic_power)/sizeof (pcic_power[0]);
760 	pcic->pc_power = pcic_power;
761 
762 	pci_ctrn = ddi_getprop(DDI_DEV_T_ANY, dip, DDI_PROP_CANSLEEP,
763 	    "pci-control-reg-number", pci_control_reg_num);
764 	pci_cfrn = ddi_getprop(DDI_DEV_T_ANY, dip, DDI_PROP_CANSLEEP,
765 	    "pci-config-reg-number", pci_config_reg_num);
766 
767 	ddi_set_driver_private(dip, pcic_nexus);
768 
769 	/*
770 	 * pcic->pc_irq is really the IPL level we want to run at
771 	 * set the default values here and override from intr spec
772 	 */
773 	pcic->pc_irq = ddi_getprop(DDI_DEV_T_ANY, dip, DDI_PROP_CANSLEEP,
774 					"interrupt-priorities", -1);
775 
776 	if (pcic->pc_irq == -1) {
777 		int			actual;
778 		uint_t			pri;
779 		ddi_intr_handle_t	hdl;
780 
781 		/* see if intrspec tells us different */
782 		if (ddi_intr_alloc(dip, &hdl, DDI_INTR_TYPE_FIXED,
783 		    0, 1, &actual, DDI_INTR_ALLOC_NORMAL) == DDI_SUCCESS) {
784 			if (ddi_intr_get_pri(hdl, &pri) == DDI_SUCCESS)
785 				pcic->pc_irq = pri;
786 			else
787 				pcic->pc_irq = LOCK_LEVEL + 1;
788 			(void) ddi_intr_free(hdl);
789 		}
790 	}
791 	pcic_nexus->an_ipl = pcic->pc_irq;
792 
793 	/*
794 	 * Check our parent bus type. We do different things based on which
795 	 * bus we're on.
796 	 */
797 	if (ddi_prop_op(DDI_DEV_T_ANY, ddi_get_parent(dip),
798 				PROP_LEN_AND_VAL_BUF, DDI_PROP_CANSLEEP,
799 				"device_type", (caddr_t)&bus_type[0], &len) !=
800 							DDI_PROP_SUCCESS) {
801 		if (ddi_prop_op(DDI_DEV_T_ANY, ddi_get_parent(dip),
802 				PROP_LEN_AND_VAL_BUF, DDI_PROP_CANSLEEP,
803 				"bus-type", (caddr_t)&bus_type[0], &len) !=
804 							DDI_PROP_SUCCESS) {
805 
806 			cmn_err(CE_CONT,
807 				"pcic%d: can't find parent bus type\n",
808 				ddi_get_instance(dip));
809 
810 			kmem_free(pcic, sizeof (pcicdev_t));
811 			return (DDI_FAILURE);
812 		}
813 	} /* ddi_prop_op("device_type") */
814 
815 	if (strcmp(bus_type, DEVI_PCI_NEXNAME) == 0) {
816 		pcic->pc_flags = PCF_PCIBUS;
817 	} else {
818 #if defined(__sparc)
819 		cmn_err(CE_CONT, "pcic%d: unsupported parent bus type: [%s]\n",
820 			ddi_get_instance(dip), bus_type);
821 
822 		kmem_free(pcic, sizeof (pcicdev_t));
823 		return (DDI_FAILURE);
824 #else
825 		pcic->pc_flags = 0;
826 #endif
827 	}
828 
829 	if ((pcic->bus_speed = ddi_getprop(DDI_DEV_T_ANY, ddi_get_parent(dip),
830 						DDI_PROP_CANSLEEP,
831 						"clock-frequency", 0)) == 0) {
832 		if (pcic->pc_flags & PCF_PCIBUS)
833 			pcic->bus_speed = PCIC_PCI_DEF_SYSCLK;
834 		else
835 			pcic->bus_speed = PCIC_ISA_DEF_SYSCLK;
836 	} else {
837 		/*
838 		 * OBP can declare the speed in Hz...
839 		 */
840 		if (pcic->bus_speed > 1000000)
841 			pcic->bus_speed /= 1000000;
842 	} /* ddi_prop_op("clock-frequency") */
843 
844 	pcic->pc_io_type = PCIC_IO_TYPE_82365SL; /* default mode */
845 
846 #ifdef	PCIC_DEBUG
847 	if (pcic_debug) {
848 		cmn_err(CE_CONT,
849 			"pcic%d: parent bus type = [%s], speed = %d MHz\n",
850 			ddi_get_instance(dip),
851 			bus_type, pcic->bus_speed);
852 	}
853 #endif
854 
855 	/*
856 	 * The reg properties on a PCI node are different than those
857 	 *	on a non-PCI node. Handle that difference here.
858 	 *	If it turns out to be a CardBus chip, we have even more
859 	 *	differences.
860 	 */
861 	if (pcic->pc_flags & PCF_PCIBUS) {
862 		int class_code;
863 #if defined(__i386) || defined(__amd64)
864 		pcic->pc_base = 0x1000000;
865 		pcic->pc_bound = (uint32_t)~0;
866 		pcic->pc_iobase = 0x1000;
867 		pcic->pc_iobound = 0xefff;
868 #elif defined(__sparc)
869 		pcic->pc_base = 0x0;
870 		pcic->pc_bound = (uint32_t)~0;
871 		pcic->pc_iobase = 0x00000;
872 		pcic->pc_iobound = 0xffff;
873 #endif
874 
875 		/* usually need to get at config space so map first */
876 		attr.devacc_attr_version = DDI_DEVICE_ATTR_V0;
877 		attr.devacc_attr_endian_flags = DDI_STRUCTURE_LE_ACC;
878 		attr.devacc_attr_dataorder = DDI_STRICTORDER_ACC;
879 
880 		if (ddi_regs_map_setup(dip, pci_cfrn,
881 					(caddr_t *)&pcic->cfgaddr,
882 					PCIC_PCI_CONFIG_REG_OFFSET,
883 					PCIC_PCI_CONFIG_REG_LENGTH,
884 					&attr,
885 					&pcic->cfg_handle) !=
886 		    DDI_SUCCESS) {
887 			cmn_err(CE_CONT,
888 				"pcic%d: unable to map config space"
889 				"regs\n",
890 				ddi_get_instance(dip));
891 
892 			kmem_free(pcic, sizeof (pcicdev_t));
893 			return (DDI_FAILURE);
894 		} /* ddi_regs_map_setup */
895 
896 		class_code = ddi_getprop(DDI_DEV_T_ANY, dip,
897 					DDI_PROP_CANSLEEP|DDI_PROP_DONTPASS,
898 					"class-code", -1);
899 #ifdef  PCIC_DEBUG
900 		if (pcic_debug) {
901 			cmn_err(CE_CONT, "pcic_attach class_code=%x\n",
902 			    class_code);
903 		}
904 #endif
905 
906 		switch (class_code) {
907 		case PCIC_PCI_CARDBUS:
908 			pcic->pc_flags |= PCF_CARDBUS;
909 			pcic->pc_io_type = PCIC_IO_TYPE_YENTA;
910 			/*
911 			 * Get access to the adapter registers on the
912 			 * PCI bus.  A 4K memory page
913 			 */
914 #if defined(PCIC_DEBUG)
915 			pcic_err(dip, 8, "Is Cardbus device\n");
916 			if (pcic_debug) {
917 				int nr;
918 				long rs;
919 				(void) ddi_dev_nregs(dip, &nr);
920 				pcic_err(dip, 9, "\tdev, cfgaddr 0x%p,"
921 				    "cfghndl 0x%p nregs %d",
922 				    (void *)pcic->cfgaddr,
923 				    (void *)pcic->cfg_handle, nr);
924 
925 				(void) ddi_dev_regsize(dip,
926 				    PCIC_PCI_CONTROL_REG_NUM, &rs);
927 
928 				pcic_err(dip, 9, "\tsize of reg %d is 0x%x\n",
929 				    PCIC_PCI_CONTROL_REG_NUM, (int)rs);
930 			}
931 #endif
932 			attr.devacc_attr_version = DDI_DEVICE_ATTR_V0;
933 			attr.devacc_attr_endian_flags = DDI_STRUCTURE_LE_ACC;
934 			attr.devacc_attr_dataorder = DDI_STRICTORDER_ACC;
935 
936 			if (ddi_regs_map_setup(dip, pci_ctrn,
937 						(caddr_t *)&pcic->ioaddr,
938 						PCIC_PCI_CONTROL_REG_OFFSET,
939 						PCIC_CB_CONTROL_REG_LENGTH,
940 						&attr, &pcic->handle) !=
941 			    DDI_SUCCESS) {
942 				cmn_err(CE_CONT,
943 					"pcic%d: unable to map PCI regs\n",
944 					ddi_get_instance(dip));
945 				ddi_regs_map_free(&pcic->cfg_handle);
946 				kmem_free(pcic, sizeof (pcicdev_t));
947 				return (DDI_FAILURE);
948 			} /* ddi_regs_map_setup */
949 
950 			/*
951 			 * Find out the chip type - If we're on a PCI bus,
952 			 *	the adapter has that information in the PCI
953 			 *	config space.
954 			 * Note that we call pcic_find_pci_type here since
955 			 *	it needs a valid mapped pcic->handle to
956 			 *	access some of the adapter registers in
957 			 *	some cases.
958 			 */
959 			if (pcic_find_pci_type(pcic) != DDI_SUCCESS) {
960 				ddi_regs_map_free(&pcic->handle);
961 				ddi_regs_map_free(&pcic->cfg_handle);
962 				kmem_free(pcic, sizeof (pcicdev_t));
963 				cmn_err(CE_WARN, "pcic: %s: unsupported "
964 								"bridge\n",
965 							ddi_get_name_addr(dip));
966 				return (DDI_FAILURE);
967 			}
968 			break;
969 
970 		default:
971 		case PCIC_PCI_PCMCIA:
972 			/*
973 			 * Get access to the adapter IO registers on the
974 			 * PCI bus config space.
975 			 */
976 			attr.devacc_attr_version = DDI_DEVICE_ATTR_V0;
977 			attr.devacc_attr_endian_flags = DDI_STRUCTURE_LE_ACC;
978 			attr.devacc_attr_dataorder = DDI_STRICTORDER_ACC;
979 
980 			/*
981 			 * We need a default mapping to the adapter's IO
982 			 *	control register space. For most adapters
983 			 *	that are of class PCIC_PCI_PCMCIA (or of
984 			 *	a default class) the control registers
985 			 *	will be using the 82365-type control/data
986 			 *	format.
987 			 */
988 			if (ddi_regs_map_setup(dip, pci_ctrn,
989 						(caddr_t *)&pcic->ioaddr,
990 						PCIC_PCI_CONTROL_REG_OFFSET,
991 						PCIC_PCI_CONTROL_REG_LENGTH,
992 						&attr,
993 						&pcic->handle) != DDI_SUCCESS) {
994 				cmn_err(CE_CONT,
995 					"pcic%d: unable to map PCI regs\n",
996 					ddi_get_instance(dip));
997 				ddi_regs_map_free(&pcic->cfg_handle);
998 				kmem_free(pcic, sizeof (pcicdev_t));
999 				return (DDI_FAILURE);
1000 			} /* ddi_regs_map_setup */
1001 
1002 			/*
1003 			 * Find out the chip type - If we're on a PCI bus,
1004 			 *	the adapter has that information in the PCI
1005 			 *	config space.
1006 			 * Note that we call pcic_find_pci_type here since
1007 			 *	it needs a valid mapped pcic->handle to
1008 			 *	access some of the adapter registers in
1009 			 *	some cases.
1010 			 */
1011 			if (pcic_find_pci_type(pcic) != DDI_SUCCESS) {
1012 				ddi_regs_map_free(&pcic->handle);
1013 				ddi_regs_map_free(&pcic->cfg_handle);
1014 				kmem_free(pcic, sizeof (pcicdev_t));
1015 				cmn_err(CE_WARN, "pcic: %s: unsupported "
1016 								"bridge\n",
1017 							ddi_get_name_addr(dip));
1018 				return (DDI_FAILURE);
1019 			}
1020 
1021 			/*
1022 			 * Some PCI-PCMCIA(R2) adapters are Yenta-compliant
1023 			 *	for extended registers even though they are
1024 			 *	not CardBus adapters. For those adapters,
1025 			 *	re-map pcic->handle to be large enough to
1026 			 *	encompass the Yenta registers.
1027 			 */
1028 			switch (pcic->pc_type) {
1029 			    case PCIC_TI_PCI1031:
1030 				ddi_regs_map_free(&pcic->handle);
1031 
1032 				if (ddi_regs_map_setup(dip,
1033 						PCIC_PCI_CONTROL_REG_NUM,
1034 						(caddr_t *)&pcic->ioaddr,
1035 						PCIC_PCI_CONTROL_REG_OFFSET,
1036 						PCIC_CB_CONTROL_REG_LENGTH,
1037 						&attr,
1038 						&pcic->handle) != DDI_SUCCESS) {
1039 					cmn_err(CE_CONT,
1040 						"pcic%d: unable to map "
1041 								"PCI regs\n",
1042 						ddi_get_instance(dip));
1043 					ddi_regs_map_free(&pcic->cfg_handle);
1044 					kmem_free(pcic, sizeof (pcicdev_t));
1045 					return (DDI_FAILURE);
1046 				} /* ddi_regs_map_setup */
1047 				break;
1048 			    default:
1049 				break;
1050 			} /* switch (pcic->pc_type) */
1051 			break;
1052 		} /* switch (class_code) */
1053 	} else {
1054 		/*
1055 		 * We're not on a PCI bus, so assume an ISA bus type
1056 		 * register property. Get access to the adapter IO
1057 		 * registers on a non-PCI bus.
1058 		 */
1059 		attr.devacc_attr_version = DDI_DEVICE_ATTR_V0;
1060 		attr.devacc_attr_endian_flags = DDI_NEVERSWAP_ACC;
1061 		attr.devacc_attr_dataorder = DDI_STRICTORDER_ACC;
1062 		pcic->mem_reg_num = PCIC_ISA_MEM_REG_NUM;
1063 		pcic->io_reg_num = PCIC_ISA_IO_REG_NUM;
1064 
1065 		if (ddi_regs_map_setup(dip, PCIC_ISA_CONTROL_REG_NUM,
1066 					(caddr_t *)&pcic->ioaddr,
1067 					PCIC_ISA_CONTROL_REG_OFFSET,
1068 					PCIC_ISA_CONTROL_REG_LENGTH,
1069 					&attr,
1070 					&pcic->handle) != DDI_SUCCESS) {
1071 			cmn_err(CE_CONT,
1072 				"pcic%d: unable to map ISA registers\n",
1073 				ddi_get_instance(dip));
1074 
1075 			kmem_free(pcic, sizeof (pcicdev_t));
1076 			return (DDI_FAILURE);
1077 		} /* ddi_regs_map_setup */
1078 
1079 		/* ISA bus is limited to 24-bits, but not first 640K */
1080 		pcic->pc_base = 0xd0000;
1081 		pcic->pc_bound = (uint32_t)~0;
1082 		pcic->pc_iobase = 0x1000;
1083 		pcic->pc_iobound = 0xefff;
1084 	} /* !PCF_PCIBUS */
1085 
1086 #ifdef  PCIC_DEBUG
1087 	if (pcic_debug) {
1088 		cmn_err(CE_CONT, "pcic_attach pc_flags=%x pc_type=%x\n",
1089 		    pcic->pc_flags, pcic->pc_type);
1090 	}
1091 #endif
1092 
1093 	/*
1094 	 * Setup various adapter registers for the PCI case. For the
1095 	 * non-PCI case, find out the chip type.
1096 	 */
1097 	if (pcic->pc_flags & PCF_PCIBUS) {
1098 		int iline;
1099 #if defined(__sparc)
1100 		iline = 0;
1101 #else
1102 		iline = cardbus_validate_iline(dip, pcic->cfg_handle);
1103 #endif
1104 
1105 		/* set flags and socket counts based on chip type */
1106 		switch (pcic->pc_type) {
1107 			uint32_t cfg;
1108 		case PCIC_INTEL_i82092:
1109 			cfg = ddi_get8(pcic->cfg_handle,
1110 					pcic->cfgaddr + PCIC_82092_PCICON);
1111 			/* we can only support 4 Socket version */
1112 			if (cfg & PCIC_82092_4_SOCKETS) {
1113 			    pcic->pc_numsockets = 4;
1114 			    pcic->pc_type = PCIC_INTEL_i82092;
1115 			    if (iline != 0xFF)
1116 				    pcic->pc_intr_mode = PCIC_INTR_MODE_PCI_1;
1117 			    else
1118 				    pcic->pc_intr_mode = PCIC_INTR_MODE_ISA;
1119 			} else {
1120 			    cmn_err(CE_CONT,
1121 				    "pcic%d: Intel 82092 adapter "
1122 				    "in unsupported configuration: 0x%x",
1123 				    ddi_get_instance(pcic->dip), cfg);
1124 			    pcic->pc_numsockets = 0;
1125 			} /* PCIC_82092_4_SOCKETS */
1126 			break;
1127 		case PCIC_CL_PD6730:
1128 		case PCIC_CL_PD6729:
1129 			pcic->pc_intr_mode = PCIC_INTR_MODE_PCI_1;
1130 			cfg = ddi_getprop(DDI_DEV_T_ANY, dip,
1131 						DDI_PROP_CANSLEEP,
1132 						"interrupts", 0);
1133 			/* if not interrupt pin then must use ISA style IRQs */
1134 			if (cfg == 0 || iline == 0xFF)
1135 				pcic->pc_intr_mode = PCIC_INTR_MODE_ISA;
1136 			else {
1137 				/*
1138 				 * we have the option to use PCI interrupts.
1139 				 * this might not be optimal but in some cases
1140 				 * is the only thing possible (sparc case).
1141 				 * we now deterine what is possible.
1142 				 */
1143 				pcic->pc_intr_mode = PCIC_INTR_MODE_PCI_1;
1144 			}
1145 			pcic->pc_numsockets = 2;
1146 			pcic->pc_flags |= PCF_IO_REMAP;
1147 			break;
1148 		case PCIC_TI_PCI1031:
1149 			/* this chip doesn't do CardBus but looks like one */
1150 			pcic->pc_flags &= ~PCF_CARDBUS;
1151 			/* FALLTHROUGH */
1152 		default:
1153 			pcic->pc_flags |= PCF_IO_REMAP;
1154 			/* FALLTHROUGH */
1155 			/* indicate feature even if not supported */
1156 			pcic->pc_flags |= PCF_DMA | PCF_ZV;
1157 			/* Not sure if these apply to all these chips */
1158 			pcic->pc_flags |= (PCF_VPPX|PCF_33VCAP);
1159 			pcic->pc_flags |= pcic_use_cbpwrctl;
1160 
1161 			pcic->pc_numsockets = 1; /* one per function */
1162 			if (iline != 0xFF) {
1163 				uint8_t cfg;
1164 				pcic->pc_intr_mode = PCIC_INTR_MODE_PCI_1;
1165 
1166 				cfg = ddi_get8(pcic->cfg_handle,
1167 					(pcic->cfgaddr + PCIC_BRIDGE_CTL_REG));
1168 				cfg &= (~PCIC_FUN_INT_MOD_ISA);
1169 				ddi_put8(pcic->cfg_handle, (pcic->cfgaddr +
1170 					PCIC_BRIDGE_CTL_REG), cfg);
1171 			}
1172 			else
1173 				pcic->pc_intr_mode = PCIC_INTR_MODE_ISA;
1174 			pcic->pc_io_type = PCIC_IOTYPE_YENTA;
1175 			break;
1176 		}
1177 	} else {
1178 		/*
1179 		 * We're not on a PCI bus so do some more
1180 		 *	checking for adapter type here.
1181 		 * For the non-PCI bus case:
1182 		 * It could be any one of a number of different chips
1183 		 * If we can't determine anything else, it is assumed
1184 		 * to be an Intel 82365SL.  The Cirrus Logic PD6710
1185 		 * has an extension register that provides unique
1186 		 * identification. Toshiba chip isn't detailed as yet.
1187 		 */
1188 
1189 		/* Init the CL id mode */
1190 		pcic_putb(pcic, 0, PCIC_CHIP_INFO, 0);
1191 		value = pcic_getb(pcic, 0, PCIC_CHIP_INFO);
1192 
1193 		/* default to Intel i82365SL and then refine */
1194 		pcic->pc_type = PCIC_I82365SL;
1195 		pcic->pc_chipname = PCIC_TYPE_I82365SL;
1196 		for (value = 0; pcic_ci_funcs[value] != NULL; value++) {
1197 			/* go until one succeeds or none left */
1198 			if (pcic_ci_funcs[value](pcic))
1199 				break;
1200 		}
1201 
1202 		/* any chip specific flags get set here */
1203 		switch (pcic->pc_type) {
1204 		case PCIC_CL_PD6722:
1205 			pcic->pc_flags |= PCF_DMA;
1206 		}
1207 
1208 		for (i = 0; i < PCIC_MAX_SOCKETS; i++) {
1209 			/*
1210 			 * look for total number of sockets.
1211 			 * basically check each possible socket for
1212 			 * presence like in probe
1213 			 */
1214 
1215 			/* turn all windows off */
1216 			pcic_putb(pcic, i, PCIC_MAPPING_ENABLE, 0);
1217 			value = pcic_getb(pcic, i, PCIC_MAPPING_ENABLE);
1218 
1219 			/*
1220 			 * if a zero is read back, then this socket
1221 			 * might be present. It would be except for
1222 			 * some systems that map the secondary PCIC
1223 			 * chip space back to the first.
1224 			 */
1225 			if (value != 0) {
1226 				/* definitely not so skip */
1227 				/* note: this is for Compaq support */
1228 				continue;
1229 			}
1230 
1231 			/* further tests */
1232 			value = pcic_getb(pcic, i, PCIC_CHIP_REVISION) &
1233 				PCIC_REV_MASK;
1234 			if (!(value >= PCIC_REV_LEVEL_LOW &&
1235 				value <= PCIC_REV_LEVEL_HI))
1236 				break;
1237 
1238 			pcic_putb(pcic, i, PCIC_SYSMEM_0_STARTLOW, 0xaa);
1239 			pcic_putb(pcic, i, PCIC_SYSMEM_1_STARTLOW, 0x55);
1240 			value = pcic_getb(pcic, i, PCIC_SYSMEM_0_STARTLOW);
1241 
1242 			j = pcic_getb(pcic, i, PCIC_SYSMEM_1_STARTLOW);
1243 			if (value != 0xaa || j != 0x55)
1244 				break;
1245 
1246 			/*
1247 			 * at this point we know if we have hardware
1248 			 * of some type and not just the bus holding
1249 			 * a pattern for us. We still have to determine
1250 			 * the case where more than 2 sockets are
1251 			 * really the same due to peculiar mappings of
1252 			 * hardware.
1253 			 */
1254 			j = pcic->pc_numsockets++;
1255 			pcic->pc_sockets[j].pcs_flags = 0;
1256 			pcic->pc_sockets[j].pcs_io = pcic->ioaddr;
1257 			pcic->pc_sockets[j].pcs_socket = i;
1258 
1259 			/* put PC Card into RESET, just in case */
1260 			value = pcic_getb(pcic, i, PCIC_INTERRUPT);
1261 			pcic_putb(pcic, i, PCIC_INTERRUPT,
1262 					value & ~PCIC_RESET);
1263 		}
1264 
1265 #if defined(PCIC_DEBUG)
1266 		if (pcic_debug)
1267 			cmn_err(CE_CONT, "num sockets = %d\n",
1268 				pcic->pc_numsockets);
1269 #endif
1270 		if (pcic->pc_numsockets == 0) {
1271 			ddi_regs_map_free(&pcic->handle);
1272 			kmem_free(pcic, sizeof (pcicdev_t));
1273 			return (DDI_FAILURE);
1274 		}
1275 
1276 		/*
1277 		 * need to think this through again in light of
1278 		 * Compaq not following the model that all the
1279 		 * chip vendors recommend.  IBM 755 seems to be
1280 		 * afflicted as well.  Basically, if the vendor
1281 		 * wired things wrong, socket 0 responds for socket 2
1282 		 * accesses, etc.
1283 		 */
1284 		if (pcic->pc_numsockets > 2) {
1285 			int count = pcic->pc_numsockets / 4;
1286 			for (i = 0; i < count; i++) {
1287 				/* put pattern into socket 0 */
1288 				pcic_putb(pcic, i,
1289 						PCIC_SYSMEM_0_STARTLOW, 0x11);
1290 
1291 				/* put pattern into socket 2 */
1292 				pcic_putb(pcic, i + 2,
1293 						PCIC_SYSMEM_0_STARTLOW, 0x33);
1294 
1295 				/* read back socket 0 */
1296 				value = pcic_getb(pcic, i,
1297 						    PCIC_SYSMEM_0_STARTLOW);
1298 
1299 				/* read back chip 1 socket 0 */
1300 				j = pcic_getb(pcic, i + 2,
1301 						PCIC_SYSMEM_0_STARTLOW);
1302 				if (j == value) {
1303 					pcic->pc_numsockets -= 2;
1304 				}
1305 			}
1306 		}
1307 
1308 		smi = 0xff;	/* no more override */
1309 
1310 		if (ddi_getprop(DDI_DEV_T_NONE, dip,
1311 				DDI_PROP_DONTPASS, "need-mult-irq",
1312 				0xffff) != 0xffff)
1313 			pcic->pc_flags |= PCF_MULT_IRQ;
1314 
1315 	} /* !PCF_PCIBUS */
1316 
1317 	/*
1318 	 * some platforms/busses need to have resources setup
1319 	 * this is temporary until a real resource allocator is
1320 	 * implemented.
1321 	 */
1322 
1323 	pcic_init_assigned(dip);
1324 
1325 	typename = pcic->pc_chipname;
1326 
1327 #ifdef	PCIC_DEBUG
1328 	if (pcic_debug) {
1329 		int nregs, nintrs;
1330 
1331 		if (ddi_dev_nregs(dip, &nregs) != DDI_SUCCESS)
1332 			nregs = 0;
1333 
1334 		if (ddi_dev_nintrs(dip, &nintrs) != DDI_SUCCESS)
1335 			nintrs = 0;
1336 
1337 		cmn_err(CE_CONT,
1338 			"pcic%d: %d register sets, %d interrupts\n",
1339 			ddi_get_instance(dip), nregs, nintrs);
1340 
1341 		nintrs = 0;
1342 		while (nregs--) {
1343 			off_t size;
1344 
1345 			if (ddi_dev_regsize(dip, nintrs, &size) ==
1346 			    DDI_SUCCESS) {
1347 				cmn_err(CE_CONT,
1348 					"\tregnum %d size %ld (0x%lx)"
1349 					"bytes",
1350 					nintrs, size, size);
1351 				if (nintrs ==
1352 				    (pcic->pc_io_type == PCIC_IO_TYPE_82365SL ?
1353 				    PCIC_ISA_CONTROL_REG_NUM :
1354 				    PCIC_PCI_CONTROL_REG_NUM))
1355 					cmn_err(CE_CONT,
1356 						" mapped at: 0x%p\n",
1357 						(void *)pcic->ioaddr);
1358 				else
1359 					cmn_err(CE_CONT, "\n");
1360 			} else {
1361 				cmn_err(CE_CONT,
1362 					"\tddi_dev_regsize(rnumber"
1363 					"= %d) returns DDI_FAILURE\n",
1364 					nintrs);
1365 			}
1366 			nintrs++;
1367 		} /* while */
1368 	} /* if (pcic_debug) */
1369 #endif
1370 
1371 	cv_init(&pcic->pm_cv, NULL, CV_DRIVER, NULL);
1372 
1373 	if (!ddi_getprop(DDI_DEV_T_NONE, dip, DDI_PROP_DONTPASS,
1374 						"disable-audio", 0))
1375 		pcic->pc_flags |= PCF_AUDIO;
1376 
1377 	if (ddi_getprop(DDI_DEV_T_ANY, dip, DDI_PROP_CANSLEEP,
1378 	    "disable-cardbus", 0))
1379 		pcic->pc_flags &= ~PCF_CARDBUS;
1380 
1381 	(void) ddi_prop_update_string(DDI_DEV_T_NONE, dip, PCICPROP_CTL,
1382 	    typename);
1383 
1384 	/*
1385 	 * Init all socket SMI levels to 0 (no SMI)
1386 	 */
1387 	for (i = 0; i < PCIC_MAX_SOCKETS; i++) {
1388 	    pcic->pc_sockets[i].pcs_smi = 0;
1389 	    pcic->pc_sockets[i].pcs_debounce_id = 0;
1390 	    pcic->pc_sockets[i].pcs_pcic = pcic;
1391 	}
1392 	pcic->pc_lastreg = -1; /* just to make sure we are in sync */
1393 
1394 	/*
1395 	 * Setup the IRQ handler(s)
1396 	 */
1397 	switch (pcic->pc_intr_mode) {
1398 		int xx;
1399 	case PCIC_INTR_MODE_ISA:
1400 	/*
1401 	 * On a non-PCI bus, we just use whatever SMI IRQ level was
1402 	 *	specified above, and the IO IRQ levels are allocated
1403 	 *	dynamically.
1404 	 */
1405 		for (xx = 15, smi = 0; xx >= 0; xx--) {
1406 			if (PCIC_IRQ(xx) &
1407 			    PCIC_AVAIL_IRQS) {
1408 				smi = pcmcia_get_intr(dip, xx);
1409 				if (smi >= 0)
1410 					break;
1411 			}
1412 		}
1413 #if defined(PCIC_DEBUG)
1414 		if (pcic_debug)
1415 			cmn_err(CE_NOTE, "\tselected IRQ %d as SMI\n", smi);
1416 #endif
1417 		/* init to same so share is easy */
1418 		for (i = 0; i < pcic->pc_numsockets; i++)
1419 			pcic->pc_sockets[i].pcs_smi = smi;
1420 		/* any special handling of IRQ levels */
1421 		if (pcic->pc_flags & PCF_MULT_IRQ) {
1422 			for (i = 2; i < pcic->pc_numsockets; i++) {
1423 				if ((i & 1) == 0) {
1424 					int xx;
1425 					for (xx = 15, smi = 0; xx >= 0; xx--) {
1426 						if (PCIC_IRQ(xx) &
1427 						    PCIC_AVAIL_IRQS) {
1428 							smi =
1429 							    pcmcia_get_intr(dip,
1430 									    xx);
1431 							if (smi >= 0)
1432 								break;
1433 						}
1434 					}
1435 				}
1436 				if (smi >= 0)
1437 					pcic->pc_sockets[i].pcs_smi = smi;
1438 			}
1439 		}
1440 		pcic->pc_intr_htblp = kmem_alloc(pcic->pc_numsockets *
1441 		    sizeof (ddi_intr_handle_t), KM_SLEEP);
1442 		for (i = 0, irqlevel = -1; i < pcic->pc_numsockets; i++) {
1443 			struct intrspec *ispecp;
1444 			struct ddi_parent_private_data *pdp;
1445 
1446 			if (irqlevel == pcic->pc_sockets[i].pcs_smi)
1447 				continue;
1448 			else {
1449 				irqlevel = pcic->pc_sockets[i].pcs_smi;
1450 			}
1451 			/*
1452 			 * now convert the allocated IRQ into an intrspec
1453 			 * and ask our parent to add it.  Don't use
1454 			 * the ddi_add_intr since we don't have a
1455 			 * default intrspec in all cases.
1456 			 *
1457 			 * note: this sort of violates DDI but we don't
1458 			 *	 get hardware intrspecs for many of the devices.
1459 			 *	 at the same time, we know how to allocate them
1460 			 *	 so we do the right thing.
1461 			 */
1462 			if (ddi_intr_alloc(dip, &pcic->pc_intr_htblp[i],
1463 			    DDI_INTR_TYPE_FIXED, 0, 1, &actual,
1464 			    DDI_INTR_ALLOC_NORMAL) != DDI_SUCCESS) {
1465 				cmn_err(CE_WARN, "%s: ddi_intr_alloc failed",
1466 				    ddi_get_name(dip));
1467 				goto isa_exit1;
1468 			}
1469 
1470 			/*
1471 			 * See earlier note:
1472 			 * Since some devices don't have 'intrspec'
1473 			 * we make one up in rootnex.
1474 			 *
1475 			 * However, it is not properly initialized as
1476 			 * the data it needs is present in this driver
1477 			 * and there is no interface to pass that up.
1478 			 * Specially 'irqlevel' is very important and
1479 			 * it is part of pcic struct.
1480 			 *
1481 			 * Set 'intrspec' up here; otherwise adding the
1482 			 * interrupt will fail.
1483 			 */
1484 			pdp = ddi_get_parent_data(dip);
1485 			ispecp = (struct intrspec *)&pdp->par_intr[0];
1486 			ispecp->intrspec_vec = irqlevel;
1487 			ispecp->intrspec_pri = pcic->pc_irq;
1488 
1489 			/* Stay compatible w/ PCMCIA */
1490 			pcic->pc_pri = (ddi_iblock_cookie_t)
1491 			    (uintptr_t)pcic->pc_irq;
1492 			pcic->pc_dcookie.idev_priority =
1493 			    (uintptr_t)pcic->pc_pri;
1494 			pcic->pc_dcookie.idev_vector = (ushort_t)irqlevel;
1495 
1496 			(void) ddi_intr_set_pri(pcic->pc_intr_htblp[i],
1497 			    pcic->pc_irq);
1498 
1499 			if (i == 0) {
1500 				mutex_init(&pcic->intr_lock, NULL, MUTEX_DRIVER,
1501 				    DDI_INTR_PRI(pcic->pc_irq));
1502 				mutex_init(&pcic->pc_lock, NULL, MUTEX_DRIVER,
1503 				    NULL);
1504 			}
1505 
1506 			if (ddi_intr_add_handler(pcic->pc_intr_htblp[i],
1507 			    pcic_intr, (caddr_t)pcic, NULL)) {
1508 				cmn_err(CE_WARN,
1509 				    "%s: ddi_intr_add_handler failed",
1510 				    ddi_get_name(dip));
1511 				goto isa_exit2;
1512 			}
1513 
1514 			if (ddi_intr_enable(pcic->pc_intr_htblp[i])) {
1515 				cmn_err(CE_WARN, "%s: ddi_intr_enable failed",
1516 				    ddi_get_name(dip));
1517 				for (j = i; j < 0; j--)
1518 					(void) ddi_intr_remove_handler(
1519 					    pcic->pc_intr_htblp[j]);
1520 				goto isa_exit2;
1521 			}
1522 		}
1523 		break;
1524 	case PCIC_INTR_MODE_PCI_1:
1525 	case PCIC_INTR_MODE_PCI:
1526 		/*
1527 		 * If we're on a PCI bus, we route all interrupts, both SMI
1528 		 * and IO interrupts, through a single interrupt line.
1529 		 * Assign the SMI IRQ level to the IO IRQ level here.
1530 		 */
1531 		pcic->pc_pci_intr_hdlp = kmem_alloc(sizeof (ddi_intr_handle_t),
1532 		    KM_SLEEP);
1533 		if (ddi_intr_alloc(dip, pcic->pc_pci_intr_hdlp,
1534 		    DDI_INTR_TYPE_FIXED, 0, 1, &actual,
1535 		    DDI_INTR_ALLOC_NORMAL) != DDI_SUCCESS)
1536 			goto pci_exit1;
1537 
1538 		if (ddi_intr_get_pri(pcic->pc_pci_intr_hdlp[0],
1539 		    &pri) != DDI_SUCCESS) {
1540 			(void) ddi_intr_free(pcic->pc_pci_intr_hdlp[0]);
1541 			goto pci_exit1;
1542 		}
1543 
1544 		pcic->pc_pri = (void *)(uintptr_t)pri;
1545 		mutex_init(&pcic->intr_lock, NULL, MUTEX_DRIVER, pcic->pc_pri);
1546 		mutex_init(&pcic->pc_lock, NULL, MUTEX_DRIVER, NULL);
1547 
1548 		if (ddi_intr_add_handler(pcic->pc_pci_intr_hdlp[0],
1549 		    pcic_intr, (caddr_t)pcic, NULL))
1550 			goto pci_exit2;
1551 
1552 		if (ddi_intr_enable(pcic->pc_pci_intr_hdlp[0])) {
1553 			(void) ddi_intr_remove_handler(
1554 			    pcic->pc_pci_intr_hdlp[0]);
1555 			goto pci_exit2;
1556 		}
1557 
1558 		/* Stay compatible w/ PCMCIA */
1559 		pcic->pc_dcookie.idev_priority = (ushort_t)pri;
1560 
1561 		/* init to same (PCI) so share is easy */
1562 		for (i = 0; i < pcic->pc_numsockets; i++)
1563 			pcic->pc_sockets[i].pcs_smi = 0xF; /* any valid */
1564 		break;
1565 	}
1566 
1567 	/*
1568 	 * Setup the adapter hardware to some reasonable defaults.
1569 	 */
1570 	mutex_enter(&pcic->pc_lock);
1571 	/* mark the driver state as attached */
1572 	pcic->pc_flags |= PCF_ATTACHED;
1573 	pcic_setup_adapter(pcic);
1574 
1575 	for (j = 0; j < pcic->pc_numsockets; j++)
1576 		if (ddi_intr_add_softint(dip,
1577 		    &pcic->pc_sockets[j].pcs_cd_softint_hdl,
1578 		    PCIC_SOFTINT_PRI_VAL, pcic_cd_softint,
1579 		    (caddr_t)&pcic->pc_sockets[j]) != DDI_SUCCESS)
1580 			goto pci_exit2;
1581 
1582 #if defined(PCIC_DEBUG)
1583 	if (pcic_debug)
1584 		cmn_err(CE_CONT, "type = %s sockets = %d\n", typename,
1585 						pcic->pc_numsockets);
1586 #endif
1587 
1588 	pcic_nexus->an_iblock = &pcic->pc_pri;
1589 	pcic_nexus->an_idev = &pcic->pc_dcookie;
1590 
1591 	mutex_exit(&pcic->pc_lock);
1592 
1593 #ifdef CARDBUS
1594 	(void) cardbus_enable_cd_intr(dip);
1595 	if (pcic_debug) {
1596 
1597 		cardbus_dump_pci_config(dip);
1598 		cardbus_dump_socket(dip);
1599 	}
1600 
1601 	/*
1602 	 * Give the Cardbus misc module a chance to do it's per-adapter
1603 	 * instance setup. Note that there is no corresponding detach()
1604 	 * call.
1605 	 */
1606 	if (pcic->pc_flags & PCF_CARDBUS)
1607 		if (cardbus_attach(dip, &pcic_cbnexus_ops) != DDI_SUCCESS) {
1608 			cmn_err(CE_CONT,
1609 			    "pcic_attach: cardbus_attach failed\n");
1610 			goto pci_exit2;
1611 		}
1612 #endif
1613 
1614 	/*
1615 	 * Give the PCMCIA misc module a chance to do it's per-adapter
1616 	 *	instance setup.
1617 	 */
1618 	if ((i = pcmcia_attach(dip, pcic_nexus)) != DDI_SUCCESS)
1619 		goto pci_exit2;
1620 
1621 	syshw_attach(pcic);
1622 	if (pcic_maxinst == -1) {
1623 		/* This assumes that all instances run at the same IPL. */
1624 		mutex_init(&pcic_deb_mtx, NULL, MUTEX_DRIVER, NULL);
1625 		cv_init(&pcic_deb_cv, NULL, CV_DRIVER, NULL);
1626 		pcic_deb_threadid = thread_create((caddr_t)NULL, 0,
1627 		    pcic_deb_thread, (caddr_t)NULL, 0, &p0, TS_RUN,
1628 		    v.v_maxsyspri - 2);
1629 	}
1630 	pcic_maxinst = max(pcic_maxinst, ddi_get_instance(dip));
1631 	/*
1632 	 * Setup a debounce timeout to do an initial card detect
1633 	 * and enable interrupts.
1634 	 */
1635 	for (j = 0; j < pcic->pc_numsockets; j++) {
1636 		shwp = kmem_alloc(sizeof (syshw_t), KM_SLEEP);
1637 		if (shwp) {
1638 			bcopy(&pcic_syshw, shwp, sizeof (pcic_syshw));
1639 			pcic_syshw.id_string[15]++;
1640 			pcic->pc_sockets[j].pcs_syshwsig =
1641 			    syshw_add2map(shwp, pcic_syshw_cardstate,
1642 				&pcic->pc_sockets[j]);
1643 		}
1644 		pcic->pc_sockets[j].pcs_debounce_id =
1645 		    pcic_add_debqueue(&pcic->pc_sockets[j],
1646 			drv_usectohz(pcic_debounce_time));
1647 	}
1648 
1649 	return (i);
1650 
1651 isa_exit2:
1652 	mutex_destroy(&pcic->intr_lock);
1653 	mutex_destroy(&pcic->pc_lock);
1654 	for (j = i; j < 0; j--)
1655 		(void) ddi_intr_free(pcic->pc_intr_htblp[j]);
1656 isa_exit1:
1657 	(void) pcmcia_return_intr(dip, pcic->pc_sockets[i].pcs_smi);
1658 	ddi_regs_map_free(&pcic->handle);
1659 	if (pcic->pc_flags & PCF_PCIBUS)
1660 		ddi_regs_map_free(&pcic->cfg_handle);
1661 	kmem_free(pcic->pc_intr_htblp, pcic->pc_numsockets *
1662 	    sizeof (ddi_intr_handle_t));
1663 	kmem_free(pcic, sizeof (pcicdev_t));
1664 		return (DDI_FAILURE);
1665 
1666 pci_exit2:
1667 	mutex_destroy(&pcic->intr_lock);
1668 	mutex_destroy(&pcic->pc_lock);
1669 	(void) ddi_intr_free(pcic->pc_pci_intr_hdlp[0]);
1670 pci_exit1:
1671 	ddi_regs_map_free(&pcic->handle);
1672 	if (pcic->pc_flags & PCF_PCIBUS)
1673 		ddi_regs_map_free(&pcic->cfg_handle);
1674 	kmem_free(pcic->pc_pci_intr_hdlp, sizeof (ddi_intr_handle_t));
1675 	kmem_free(pcic, sizeof (pcicdev_t));
1676 	return (DDI_FAILURE);
1677 }
1678 
1679 /*
1680  * pcic_detach()
1681  *	request to detach from the system
1682  */
1683 static int
1684 pcic_detach(dev_info_t *dip, ddi_detach_cmd_t cmd)
1685 {
1686 	anp_t *anp = ddi_get_driver_private(dip);
1687 	pcicdev_t *pcic = anp->an_private;
1688 	int i;
1689 
1690 	switch (cmd) {
1691 	case DDI_DETACH:
1692 		/* don't detach if the nexus still talks to us */
1693 		if (pcic->pc_callback != NULL)
1694 			return (DDI_FAILURE);
1695 		syshw_detach(pcic);
1696 
1697 		/* kill off the pm simulation */
1698 		if (pcic->pc_pmtimer)
1699 			(void) untimeout(pcic->pc_pmtimer);
1700 
1701 		/* turn everything off for all sockets and chips */
1702 		for (i = 0; i < pcic->pc_numsockets; i++) {
1703 			if (pcic->pc_sockets[i].pcs_debounce_id)
1704 				pcic_rm_debqueue(
1705 				    pcic->pc_sockets[i].pcs_debounce_id);
1706 			pcic->pc_sockets[i].pcs_debounce_id = 0;
1707 
1708 			pcic_putb(pcic, i, PCIC_MANAGEMENT_INT, 0);
1709 			pcic_putb(pcic, i, PCIC_CARD_DETECT, 0);
1710 			pcic_putb(pcic, i, PCIC_MAPPING_ENABLE, 0);
1711 			/* disable interrupts and put card into RESET */
1712 			pcic_putb(pcic, i, PCIC_INTERRUPT, 0);
1713 		}
1714 		(void) ddi_intr_disable(pcic->pc_pci_intr_hdlp[0]);
1715 		(void) ddi_intr_remove_handler(pcic->pc_pci_intr_hdlp[0]);
1716 		(void) ddi_intr_free(pcic->pc_pci_intr_hdlp[0]);
1717 		kmem_free(pcic->pc_pci_intr_hdlp, sizeof (ddi_intr_handle_t));
1718 		pcic->pc_flags = 0;
1719 		mutex_destroy(&pcic->pc_lock);
1720 		mutex_destroy(&pcic->intr_lock);
1721 		cv_destroy(&pcic->pm_cv);
1722 		if (pcic->pc_flags & PCF_PCIBUS)
1723 		    ddi_regs_map_free(&pcic->cfg_handle);
1724 		if (pcic->handle)
1725 		    ddi_regs_map_free(&pcic->handle);
1726 		kmem_free(pcic, sizeof (pcicdev_t));
1727 		ddi_soft_state_free(pcic_soft_state_p, ddi_get_instance(dip));
1728 		return (DDI_SUCCESS);
1729 
1730 	case DDI_SUSPEND:
1731 	case DDI_PM_SUSPEND:
1732 		/*
1733 		 * we got a suspend event (either real or imagined)
1734 		 * so notify the nexus proper that all existing cards
1735 		 * should go away.
1736 		 */
1737 		mutex_enter(&pcic->pc_lock);
1738 #ifdef CARDBUS
1739 		if (pcic->pc_flags & PCF_CARDBUS)
1740 			for (i = 0; i < pcic->pc_numsockets; i++)
1741 				if ((pcic->pc_sockets[i].pcs_flags &
1742 				    (PCS_CARD_PRESENT|PCS_CARD_ISCARDBUS)) ==
1743 				    (PCS_CARD_PRESENT|PCS_CARD_ISCARDBUS))
1744 					if (!cardbus_can_suspend(dip)) {
1745 						mutex_exit(&pcic->pc_lock);
1746 						cmn_err(CE_WARN,
1747 						    "Please unconfigure all "
1748 						    "CardBus devices before "
1749 						    "attempting to suspend\n");
1750 						return (DDI_FAILURE);
1751 					}
1752 #endif
1753 		/* turn everything off for all sockets and chips */
1754 		for (i = 0; i < pcic->pc_numsockets; i++) {
1755 			if (pcic->pc_sockets[i].pcs_debounce_id)
1756 				pcic_rm_debqueue(
1757 				    pcic->pc_sockets[i].pcs_debounce_id);
1758 			pcic->pc_sockets[i].pcs_debounce_id = 0;
1759 
1760 			pcic_putb(pcic, i, PCIC_MANAGEMENT_INT, 0);
1761 			pcic_putb(pcic, i, PCIC_CARD_DETECT, 0);
1762 			pcic_putb(pcic, i, PCIC_MAPPING_ENABLE, 0);
1763 			/* disable interrupts and put card into RESET */
1764 			pcic_putb(pcic, i, PCIC_INTERRUPT, 0);
1765 			pcic_putb(pcic, i, PCIC_POWER_CONTROL, 0);
1766 			if (pcic->pc_flags & PCF_CBPWRCTL)
1767 				pcic_putcb(pcic, CB_CONTROL, 0);
1768 
1769 			if (pcic->pc_sockets[i].pcs_flags & PCS_CARD_PRESENT) {
1770 				pcic->pc_sockets[i].pcs_flags = PCS_STARTING;
1771 				/*
1772 				 * Because we are half way through a save
1773 				 * all this does is schedule a removal event
1774 				 * to cs for when the system comes back.
1775 				 * This doesn't actually matter.
1776 				 */
1777 				if (!pcic_do_pcmcia_sr && pcic_do_removal &&
1778 				    pcic->pc_callback) {
1779 					PC_CALLBACK(pcic->dip, pcic->pc_cb_arg,
1780 					    PCE_CARD_REMOVAL,
1781 					    pcic->pc_sockets[i].pcs_socket);
1782 				}
1783 			}
1784 		}
1785 
1786 		pcic->pc_flags |= PCF_SUSPENDED;
1787 		mutex_exit(&pcic->pc_lock);
1788 		pcic_delayed_resume_toid = 0;
1789 
1790 		/*
1791 		 * when true power management exists, save the adapter
1792 		 * state here to enable a recovery.  For the emulation
1793 		 * condition, the state is gone
1794 		 */
1795 		return (DDI_SUCCESS);
1796 
1797 	default:
1798 		return (EINVAL);
1799 	}
1800 }
1801 
1802 static uint32_t pcic_tisysctl_onbits = ((1<<27) | (1<<15) | (1<<14));
1803 static uint32_t pcic_tisysctl_offbits = 0;
1804 static uint32_t pcic_default_latency = 0x40;
1805 
1806 static void
1807 pcic_setup_adapter(pcicdev_t *pcic)
1808 {
1809 	int i;
1810 	int value, flags;
1811 
1812 	if (pcic->pc_flags & PCF_PCIBUS) {
1813 		/*
1814 		 * all PCI-to-PCMCIA bus bridges need memory and I/O enabled
1815 		 */
1816 		flags = (PCIC_ENABLE_IO | PCIC_ENABLE_MEM);
1817 		pcic_iomem_pci_ctl(pcic->cfg_handle, pcic->cfgaddr, flags);
1818 	}
1819 	/* enable each socket */
1820 	for (i = 0; i < pcic->pc_numsockets; i++) {
1821 		pcic->pc_sockets[i].pcs_flags = 0;
1822 		/* find out the socket capabilities (I/O vs memory) */
1823 		value = pcic_getb(pcic, i,
1824 					PCIC_CHIP_REVISION) & PCIC_REV_ID_MASK;
1825 		if (value == PCIC_REV_ID_IO || value == PCIC_REV_ID_BOTH)
1826 			pcic->pc_sockets[i].pcs_flags |= PCS_SOCKET_IO;
1827 
1828 		/* disable all windows just in case */
1829 		pcic_putb(pcic, i, PCIC_MAPPING_ENABLE, 0);
1830 
1831 		switch (pcic->pc_type) {
1832 			uint32_t cfg32;
1833 			uint16_t cfg16;
1834 			uint8_t cfg;
1835 
1836 		    /* enable extended registers for Vadem */
1837 		    case PCIC_VADEM_VG469:
1838 		    case PCIC_VADEM:
1839 
1840 			/* enable card status change interrupt for socket */
1841 			break;
1842 
1843 		    case PCIC_I82365SL:
1844 			break;
1845 
1846 		    case PCIC_CL_PD6710:
1847 			pcic_putb(pcic, 0, PCIC_MISC_CTL_2, PCIC_LED_ENABLE);
1848 			break;
1849 
1850 			/*
1851 			 * On the CL_6730, we need to set up the interrupt
1852 			 * signalling mode (PCI mode) and set the SMI and
1853 			 * IRQ interrupt lines to PCI/level-mode.
1854 			 */
1855 		    case PCIC_CL_PD6730:
1856 			switch (pcic->pc_intr_mode) {
1857 			case PCIC_INTR_MODE_PCI_1:
1858 				clext_reg_write(pcic, i, PCIC_CLEXT_MISC_CTL_3,
1859 						((clext_reg_read(pcic, i,
1860 						PCIC_CLEXT_MISC_CTL_3) &
1861 						~PCIC_CLEXT_INT_PCI) |
1862 						PCIC_CLEXT_INT_PCI));
1863 				clext_reg_write(pcic, i, PCIC_CLEXT_EXT_CTL_1,
1864 						(PCIC_CLEXT_IRQ_LVL_MODE |
1865 						PCIC_CLEXT_SMI_LVL_MODE));
1866 				cfg = PCIC_CL_LP_DYN_MODE;
1867 				pcic_putb(pcic, i, PCIC_MISC_CTL_2, cfg);
1868 				break;
1869 			case PCIC_INTR_MODE_ISA:
1870 				break;
1871 			}
1872 			break;
1873 			/*
1874 			 * On the CL_6729, we set the SMI and IRQ interrupt
1875 			 *	lines to PCI/level-mode. as well as program the
1876 			 *	correct clock speed divider bit.
1877 			 */
1878 		    case PCIC_CL_PD6729:
1879 			switch (pcic->pc_intr_mode) {
1880 			case PCIC_INTR_MODE_PCI_1:
1881 				clext_reg_write(pcic, i, PCIC_CLEXT_EXT_CTL_1,
1882 						(PCIC_CLEXT_IRQ_LVL_MODE |
1883 						PCIC_CLEXT_SMI_LVL_MODE));
1884 
1885 				break;
1886 			case PCIC_INTR_MODE_ISA:
1887 				break;
1888 			}
1889 			if (pcic->bus_speed > PCIC_PCI_25MHZ && i == 0) {
1890 				cfg = 0;
1891 				cfg |= PCIC_CL_TIMER_CLK_DIV;
1892 				pcic_putb(pcic, i, PCIC_MISC_CTL_2, cfg);
1893 			}
1894 			break;
1895 		    case PCIC_INTEL_i82092:
1896 			cfg = PCIC_82092_EN_TIMING;
1897 			if (pcic->bus_speed < PCIC_SYSCLK_33MHZ)
1898 			    cfg |= PCIC_82092_PCICLK_25MHZ;
1899 			ddi_put8(pcic->cfg_handle, pcic->cfgaddr +
1900 						PCIC_82092_PCICON, cfg);
1901 			break;
1902 		    case PCIC_TI_PCI1130:
1903 		    case PCIC_TI_PCI1131:
1904 		    case PCIC_TI_PCI1250:
1905 		    case PCIC_TI_PCI1031:
1906 			cfg = ddi_get8(pcic->cfg_handle,
1907 					pcic->cfgaddr + PCIC_DEVCTL_REG);
1908 			cfg &= ~PCIC_DEVCTL_INTR_MASK;
1909 			switch (pcic->pc_intr_mode) {
1910 			case PCIC_INTR_MODE_ISA:
1911 				cfg |= PCIC_DEVCTL_INTR_ISA;
1912 				break;
1913 			}
1914 #ifdef PCIC_DEBUG
1915 			if (pcic_debug) {
1916 				cmn_err(CE_CONT, "pcic_setup_adapter: "
1917 				    "write reg 0x%x=%x \n",
1918 				    PCIC_DEVCTL_REG, cfg);
1919 			}
1920 #endif
1921 			ddi_put8(pcic->cfg_handle,
1922 					pcic->cfgaddr + PCIC_DEVCTL_REG,
1923 					cfg);
1924 
1925 			cfg = ddi_get8(pcic->cfg_handle,
1926 					pcic->cfgaddr + PCIC_CRDCTL_REG);
1927 			cfg &= ~(PCIC_CRDCTL_PCIINTR|PCIC_CRDCTL_PCICSC|
1928 					PCIC_CRDCTL_PCIFUNC);
1929 			switch (pcic->pc_intr_mode) {
1930 			case PCIC_INTR_MODE_PCI_1:
1931 				cfg |= PCIC_CRDCTL_PCIINTR |
1932 					PCIC_CRDCTL_PCICSC |
1933 					PCIC_CRDCTL_PCIFUNC;
1934 				pcic->pc_flags |= PCF_USE_SMI;
1935 				break;
1936 			}
1937 #ifdef PCIC_DEBUG
1938 			if (pcic_debug) {
1939 				cmn_err(CE_CONT, "pcic_setup_adapter: "
1940 				    " write reg 0x%x=%x \n",
1941 				    PCIC_CRDCTL_REG, cfg);
1942 			}
1943 #endif
1944 			ddi_put8(pcic->cfg_handle,
1945 					pcic->cfgaddr + PCIC_CRDCTL_REG,
1946 					cfg);
1947 			break;
1948 		    case PCIC_TI_PCI1221:
1949 		    case PCIC_TI_PCI1225:
1950 			cfg = ddi_get8(pcic->cfg_handle,
1951 			    pcic->cfgaddr + PCIC_DEVCTL_REG);
1952 			cfg |= (PCIC_DEVCTL_INTR_DFLT | PCIC_DEVCTL_3VCAPABLE);
1953 #ifdef PCIC_DEBUG
1954 			if (pcic_debug) {
1955 				cmn_err(CE_CONT, "pcic_setup_adapter: "
1956 				    " write reg 0x%x=%x \n",
1957 				    PCIC_DEVCTL_REG, cfg);
1958 			}
1959 #endif
1960 			ddi_put8(pcic->cfg_handle,
1961 			    pcic->cfgaddr + PCIC_DEVCTL_REG, cfg);
1962 
1963 			cfg = ddi_get8(pcic->cfg_handle,
1964 			    pcic->cfgaddr + PCIC_DIAG_REG);
1965 			if (pcic->pc_type == PCIC_TI_PCI1225) {
1966 				cfg |= (PCIC_DIAG_CSC | PCIC_DIAG_ASYNC);
1967 			} else {
1968 				cfg |= PCIC_DIAG_ASYNC;
1969 			}
1970 			pcic->pc_flags |= PCF_USE_SMI;
1971 #ifdef PCIC_DEBUG
1972 			if (pcic_debug) {
1973 				cmn_err(CE_CONT, "pcic_setup_adapter: "
1974 				    " write reg 0x%x=%x \n",
1975 				    PCIC_DIAG_REG, cfg);
1976 			}
1977 #endif
1978 			ddi_put8(pcic->cfg_handle,
1979 			    pcic->cfgaddr + PCIC_DIAG_REG, cfg);
1980 			break;
1981 		    case PCIC_TI_PCI1520:
1982 		    case PCIC_TI_PCI1510:
1983 		    case PCIC_TI_VENDOR:
1984 			if (pcic->pc_intr_mode == PCIC_INTR_MODE_ISA) {
1985 				cfg = ddi_get8(pcic->cfg_handle,
1986 					pcic->cfgaddr + PCIC_BRIDGE_CTL_REG);
1987 				cfg |= PCIC_FUN_INT_MOD_ISA;
1988 				ddi_put8(pcic->cfg_handle,
1989 					pcic->cfgaddr + PCIC_BRIDGE_CTL_REG,
1990 					cfg);
1991 			}
1992 			cfg = ddi_get8(pcic->cfg_handle,
1993 					pcic->cfgaddr + PCIC_DEVCTL_REG);
1994 			cfg &= ~PCIC_DEVCTL_INTR_MASK;
1995 			if (pcic->pc_intr_mode == PCIC_INTR_MODE_ISA)
1996 				cfg |= PCIC_DEVCTL_INTR_ISA;
1997 			ddi_put8(pcic->cfg_handle,
1998 					pcic->cfgaddr + PCIC_DEVCTL_REG,
1999 					cfg);
2000 
2001 			/* tie INTA and INTB together */
2002 			cfg = ddi_get8(pcic->cfg_handle,
2003 				(pcic->cfgaddr + PCIC_SYSCTL_REG + 3));
2004 			cfg |= PCIC_SYSCTL_INTRTIE;
2005 			ddi_put8(pcic->cfg_handle, (pcic->cfgaddr +
2006 				PCIC_SYSCTL_REG + 3), cfg);
2007 			cfg = ddi_get8(pcic->cfg_handle,
2008 			    pcic->cfgaddr + PCIC_DIAG_REG);
2009 			cfg |= (PCIC_DIAG_CSC | PCIC_DIAG_ASYNC);
2010 			ddi_put8(pcic->cfg_handle,
2011 			    pcic->cfgaddr + PCIC_DIAG_REG, cfg);
2012 			break;
2013 		    case PCIC_TI_PCI1410:
2014 			cfg = ddi_get8(pcic->cfg_handle,
2015 			    pcic->cfgaddr + PCIC_DIAG_REG);
2016 			cfg |= (PCIC_DIAG_CSC | PCIC_DIAG_ASYNC);
2017 			ddi_put8(pcic->cfg_handle,
2018 			    pcic->cfgaddr + PCIC_DIAG_REG, cfg);
2019 			break;
2020 		    case PCIC_TOSHIBA_TOPIC100:
2021 		    case PCIC_TOSHIBA_TOPIC95:
2022 		    case PCIC_TOSHIBA_VENDOR:
2023 			cfg = ddi_get8(pcic->cfg_handle, pcic->cfgaddr +
2024 				PCIC_TOSHIBA_SLOT_CTL_REG);
2025 			cfg |= (PCIC_TOSHIBA_SCR_SLOTON |
2026 				PCIC_TOSHIBA_SCR_SLOTEN);
2027 			cfg &= (~PCIC_TOSHIBA_SCR_PRT_MASK);
2028 			cfg |= PCIC_TOSHIBA_SCR_PRT_3E2;
2029 			ddi_put8(pcic->cfg_handle, pcic->cfgaddr +
2030 				PCIC_TOSHIBA_SLOT_CTL_REG, cfg);
2031 			cfg = ddi_get8(pcic->cfg_handle, pcic->cfgaddr +
2032 				PCIC_TOSHIBA_INTR_CTL_REG);
2033 			switch (pcic->pc_intr_mode) {
2034 			case PCIC_INTR_MODE_ISA:
2035 				cfg &= ~PCIC_TOSHIBA_ICR_SRC;
2036 				ddi_put8(pcic->cfg_handle,
2037 					pcic->cfgaddr +
2038 					PCIC_TOSHIBA_INTR_CTL_REG, cfg);
2039 
2040 				cfg = ddi_get8(pcic->cfg_handle,
2041 					pcic->cfgaddr + PCIC_BRIDGE_CTL_REG);
2042 				cfg |= PCIC_FUN_INT_MOD_ISA;
2043 				ddi_put8(pcic->cfg_handle,
2044 					pcic->cfgaddr + PCIC_BRIDGE_CTL_REG,
2045 					cfg);
2046 				break;
2047 			case PCIC_INTR_MODE_PCI_1:
2048 				cfg |= PCIC_TOSHIBA_ICR_SRC;
2049 				cfg &= (~PCIC_TOSHIBA_ICR_PIN_MASK);
2050 				cfg |= PCIC_TOSHIBA_ICR_PIN_INTA;
2051 				ddi_put8(pcic->cfg_handle,
2052 					pcic->cfgaddr +
2053 					PCIC_TOSHIBA_INTR_CTL_REG, cfg);
2054 				break;
2055 			}
2056 			break;
2057 		    case PCIC_O2MICRO_VENDOR:
2058 			cfg32 = ddi_get32(pcic->cfg_handle,
2059 				(uint32_t *)(pcic->cfgaddr +
2060 				PCIC_O2MICRO_MISC_CTL));
2061 			switch (pcic->pc_intr_mode) {
2062 			case PCIC_INTR_MODE_ISA:
2063 				cfg32 |= (PCIC_O2MICRO_ISA_LEGACY |
2064 					PCIC_O2MICRO_INT_MOD_PCI);
2065 				ddi_put32(pcic->cfg_handle,
2066 					(uint32_t *)(pcic->cfgaddr +
2067 					PCIC_O2MICRO_MISC_CTL),
2068 					cfg32);
2069 				cfg = ddi_get8(pcic->cfg_handle,
2070 					pcic->cfgaddr + PCIC_BRIDGE_CTL_REG);
2071 				cfg |= PCIC_FUN_INT_MOD_ISA;
2072 				ddi_put8(pcic->cfg_handle,
2073 					pcic->cfgaddr + PCIC_BRIDGE_CTL_REG,
2074 					cfg);
2075 				break;
2076 			case PCIC_INTR_MODE_PCI_1:
2077 				cfg32 &= ~PCIC_O2MICRO_ISA_LEGACY;
2078 				cfg32 |= PCIC_O2MICRO_INT_MOD_PCI;
2079 				ddi_put32(pcic->cfg_handle,
2080 					(uint32_t *)(pcic->cfgaddr +
2081 					PCIC_O2MICRO_MISC_CTL),
2082 					cfg32);
2083 				break;
2084 			}
2085 			break;
2086 		    case PCIC_RICOH_VENDOR:
2087 			if (pcic->pc_intr_mode == PCIC_INTR_MODE_ISA) {
2088 				cfg16 = ddi_get16(pcic->cfg_handle,
2089 					(uint16_t *)(pcic->cfgaddr +
2090 					PCIC_RICOH_MISC_CTL_2));
2091 				cfg16 |= (PCIC_RICOH_CSC_INT_MOD |
2092 					PCIC_RICOH_FUN_INT_MOD);
2093 				ddi_put16(pcic->cfg_handle,
2094 					(uint16_t *)(pcic->cfgaddr +
2095 					PCIC_RICOH_MISC_CTL_2),
2096 					cfg16);
2097 
2098 				cfg16 = ddi_get16(pcic->cfg_handle,
2099 					(uint16_t *)(pcic->cfgaddr +
2100 					PCIC_RICOH_MISC_CTL));
2101 				cfg16 |= PCIC_RICOH_SIRQ_EN;
2102 				ddi_put16(pcic->cfg_handle,
2103 					(uint16_t *)(pcic->cfgaddr +
2104 					PCIC_RICOH_MISC_CTL),
2105 					cfg16);
2106 
2107 				cfg = ddi_get8(pcic->cfg_handle,
2108 					pcic->cfgaddr + PCIC_BRIDGE_CTL_REG);
2109 				cfg |= PCIC_FUN_INT_MOD_ISA;
2110 				ddi_put8(pcic->cfg_handle,
2111 					pcic->cfgaddr + PCIC_BRIDGE_CTL_REG,
2112 					cfg);
2113 			}
2114 			break;
2115 		    default:
2116 			break;
2117 		} /* switch */
2118 
2119 		/* setup general card status change interrupt */
2120 		switch (pcic->pc_type) {
2121 			case PCIC_TI_PCI1225:
2122 			case PCIC_TI_PCI1221:
2123 			case PCIC_TI_PCI1031:
2124 			case PCIC_TI_PCI1520:
2125 			case PCIC_TI_PCI1410:
2126 				pcic_putb(pcic, i, PCIC_MANAGEMENT_INT,
2127 				    PCIC_CHANGE_DEFAULT);
2128 				break;
2129 			default:
2130 				if (pcic->pc_intr_mode ==
2131 					PCIC_INTR_MODE_PCI_1) {
2132 					pcic_putb(pcic, i, PCIC_MANAGEMENT_INT,
2133 						PCIC_CHANGE_DEFAULT);
2134 					break;
2135 				} else {
2136 					pcic_putb(pcic, i, PCIC_MANAGEMENT_INT,
2137 						PCIC_CHANGE_DEFAULT |
2138 					(pcic->pc_sockets[i].pcs_smi << 4));
2139 					break;
2140 				}
2141 		}
2142 
2143 		pcic->pc_flags |= PCF_INTRENAB;
2144 
2145 		/* take card out of RESET */
2146 		pcic_putb(pcic, i, PCIC_INTERRUPT, PCIC_RESET);
2147 		/* turn power off and let CS do this */
2148 		pcic_putb(pcic, i, PCIC_POWER_CONTROL, 0);
2149 
2150 		/* final chip specific initialization */
2151 		switch (pcic->pc_type) {
2152 		    case PCIC_VADEM:
2153 			pcic_putb(pcic, i, PCIC_VG_CONTROL,
2154 					PCIC_VC_DELAYENABLE);
2155 			pcic->pc_flags |= PCF_DEBOUNCE;
2156 			/* FALLTHROUGH */
2157 		    case PCIC_I82365SL:
2158 			pcic_putb(pcic, i, PCIC_GLOBAL_CONTROL,
2159 					PCIC_GC_CSC_WRITE);
2160 			/* clear any pending interrupts */
2161 			value = pcic_getb(pcic, i, PCIC_CARD_STATUS_CHANGE);
2162 			pcic_putb(pcic, i, PCIC_CARD_STATUS_CHANGE, value);
2163 			break;
2164 		    /* The 82092 uses PCI config space to enable interrupts */
2165 		    case PCIC_INTEL_i82092:
2166 			pcic_82092_smiirq_ctl(pcic, i, PCIC_82092_CTL_SMI,
2167 							PCIC_82092_INT_ENABLE);
2168 			break;
2169 		    case PCIC_CL_PD6729:
2170 			if (pcic->bus_speed >= PCIC_PCI_DEF_SYSCLK && i == 0) {
2171 				value = pcic_getb(pcic, i, PCIC_MISC_CTL_2);
2172 				pcic_putb(pcic, i, PCIC_MISC_CTL_2,
2173 						value | PCIC_CL_TIMER_CLK_DIV);
2174 			}
2175 			break;
2176 		} /* switch */
2177 
2178 #if defined(PCIC_DEBUG)
2179 		if (pcic_debug)
2180 			cmn_err(CE_CONT,
2181 				"socket %d value=%x, flags = %x (%s)\n",
2182 				i, value, pcic->pc_sockets[i].pcs_flags,
2183 				(pcic->pc_sockets[i].pcs_flags &
2184 					PCS_CARD_PRESENT) ?
2185 						"card present" : "no card");
2186 #endif
2187 	}
2188 }
2189 
2190 /*
2191  * pcic_intr(caddr_t, caddr_t)
2192  *	interrupt handler for the PCIC style adapter
2193  *	handles all basic interrupts and also checks
2194  *	for status changes and notifies the nexus if
2195  *	necessary
2196  *
2197  *	On PCI bus adapters, also handles all card
2198  *	IO interrupts.
2199  */
2200 /*ARGSUSED*/
2201 uint32_t
2202 pcic_intr(caddr_t arg1, caddr_t arg2)
2203 {
2204 	pcicdev_t *pcic = (pcicdev_t *)arg1;
2205 	int value = 0, i, ret = DDI_INTR_UNCLAIMED;
2206 	uint8_t status;
2207 	uint_t io_ints;
2208 
2209 #if defined(PCIC_DEBUG)
2210 	pcic_err(pcic->dip, 0xf,
2211 		"pcic_intr: enter pc_flags=0x%x PCF_ATTACHED=0x%x"
2212 		" pc_numsockets=%d \n",
2213 		pcic->pc_flags, PCF_ATTACHED, pcic->pc_numsockets);
2214 #endif
2215 
2216 	if (!(pcic->pc_flags & PCF_ATTACHED))
2217 	    return (DDI_INTR_UNCLAIMED);
2218 
2219 	mutex_enter(&pcic->intr_lock);
2220 
2221 	if (pcic->pc_flags & PCF_SUSPENDED) {
2222 		mutex_exit(&pcic->intr_lock);
2223 		return (ret);
2224 	}
2225 
2226 	/*
2227 	 * need to change to only ACK and touch the slot that
2228 	 * actually caused the interrupt.  Currently everything
2229 	 * is acked
2230 	 *
2231 	 * we need to look at all known sockets to determine
2232 	 * what might have happened, so step through the list
2233 	 * of them
2234 	 */
2235 #ifdef VOYAGER
2236 	ret = syshw_intr_hi(pcic);
2237 #endif
2238 
2239 	/*
2240 	 * Set the bitmask for IO interrupts to initially include all sockets
2241 	 */
2242 	io_ints = (1 << pcic->pc_numsockets) - 1;
2243 
2244 	for (i = 0; i < pcic->pc_numsockets; i++) {
2245 		int card_type;
2246 		pcic_socket_t *sockp;
2247 		int value_cb = 0;
2248 
2249 		sockp = &pcic->pc_sockets[i];
2250 		/* get the socket's I/O addresses */
2251 
2252 		if (sockp->pcs_flags & PCS_WAITING) {
2253 			io_ints &= ~(1 << i);
2254 			continue;
2255 		}
2256 
2257 		if (sockp->pcs_flags & PCS_CARD_IO)
2258 			card_type = IF_IO;
2259 		else
2260 			card_type = IF_MEMORY;
2261 
2262 		if (pcic->pc_io_type == PCIC_IO_TYPE_YENTA)
2263 			value_cb = pcic_getcb(pcic, CB_STATUS_EVENT);
2264 
2265 		value = pcic_change(pcic, i);
2266 
2267 		if ((value != 0) || (value_cb != 0)) {
2268 			int x = pcic->pc_cb_arg;
2269 
2270 			ret = DDI_INTR_CLAIMED;
2271 
2272 #if defined(PCIC_DEBUG)
2273 			pcic_err(pcic->dip, 0x9,
2274 			    "card_type = %d, value_cb = 0x%x\n",
2275 			    card_type,
2276 			    value_cb ? value_cb :
2277 				pcic_getcb(pcic, CB_STATUS_EVENT));
2278 			if (pcic_debug)
2279 				cmn_err(CE_CONT,
2280 					"\tchange on socket %d (%x)\n", i,
2281 					value);
2282 #endif
2283 			/* find out what happened */
2284 			status = pcic_getb(pcic, i, PCIC_INTERFACE_STATUS);
2285 
2286 			/* acknowledge the interrupt */
2287 			if (value_cb)
2288 				pcic_putcb(pcic, CB_STATUS_EVENT, value_cb);
2289 
2290 			if (value)
2291 				pcic_putb(pcic, i, PCIC_CARD_STATUS_CHANGE,
2292 				    value);
2293 
2294 			if (pcic->pc_callback == NULL) {
2295 				/* if not callback handler, nothing to do */
2296 				continue;
2297 			}
2298 
2299 			/* Card Detect */
2300 			if (value & PCIC_CD_DETECT ||
2301 			    value_cb & CB_PS_CCDMASK) {
2302 				uint8_t irq;
2303 #if defined(PCIC_DEBUG)
2304 				if (pcic_debug)
2305 					cmn_err(CE_CONT,
2306 						"\tcd_detect: status=%x,"
2307 						" flags=%x\n",
2308 						status, sockp->pcs_flags);
2309 #else
2310 #ifdef lint
2311 				if (status == 0)
2312 				    status++;
2313 #endif
2314 #endif
2315 				/*
2316 				 * Turn off all interrupts for this socket here.
2317 				 */
2318 				irq = pcic_getb(pcic, sockp->pcs_socket,
2319 				    PCIC_MANAGEMENT_INT);
2320 				irq &= ~PCIC_CHANGE_MASK;
2321 				pcic_putb(pcic, sockp->pcs_socket,
2322 				    PCIC_MANAGEMENT_INT, irq);
2323 
2324 				pcic_putcb(pcic, CB_STATUS_MASK, 0x0);
2325 
2326 				/*
2327 				 * Put the socket in debouncing state so that
2328 				 * the leaf driver won't receive interrupts.
2329 				 * Crucial for handling surprise-removal.
2330 				 */
2331 				sockp->pcs_flags |= PCS_DEBOUNCING;
2332 
2333 				if (!sockp->pcs_cd_softint_flg) {
2334 					sockp->pcs_cd_softint_flg = 1;
2335 					(void) ddi_intr_trigger_softint(
2336 					    sockp->pcs_cd_softint_hdl, NULL);
2337 				}
2338 
2339 				io_ints &= ~(1 << i);
2340 			} /* PCIC_CD_DETECT */
2341 
2342 			/* Ready/Change Detect */
2343 			sockp->pcs_state ^= SBM_RDYBSY;
2344 			if (card_type == IF_MEMORY && value & PCIC_RD_DETECT) {
2345 				sockp->pcs_flags |= PCS_READY;
2346 				PC_CALLBACK(pcic->dip, x, PCE_CARD_READY, i);
2347 			}
2348 
2349 			/* Battery Warn Detect */
2350 			if (card_type == IF_MEMORY &&
2351 			    value & PCIC_BW_DETECT &&
2352 			    !(sockp->pcs_state & SBM_BVD2)) {
2353 				sockp->pcs_state |= SBM_BVD2;
2354 				PC_CALLBACK(pcic->dip, x,
2355 						PCE_CARD_BATTERY_WARN, i);
2356 			}
2357 
2358 			/* Battery Dead Detect */
2359 			if (value & PCIC_BD_DETECT) {
2360 				/*
2361 				 * need to work out event if RI not enabled
2362 				 * and card_type == IF_IO
2363 				 */
2364 				if (card_type == IF_MEMORY &&
2365 					!(sockp->pcs_state & SBM_BVD1)) {
2366 					sockp->pcs_state |= SBM_BVD1;
2367 					PC_CALLBACK(pcic->dip, x,
2368 							PCE_CARD_BATTERY_DEAD,
2369 							i);
2370 				} else {
2371 					/*
2372 					 * information in pin replacement
2373 					 * register if one is available
2374 					 */
2375 					PC_CALLBACK(pcic->dip, x,
2376 							PCE_CARD_STATUS_CHANGE,
2377 							i);
2378 				} /* IF_MEMORY */
2379 			} /* PCIC_BD_DETECT */
2380 		} /* if pcic_change */
2381 		/*
2382 		 * for any controllers that we can detect whether a socket
2383 		 * had an interrupt for the PC Card, we should sort that out
2384 		 * here.
2385 		 */
2386 	} /* for pc_numsockets */
2387 
2388 	/*
2389 	 * If we're on a PCI bus, we may need to cycle through each IO
2390 	 *	interrupt handler that is registered since they all
2391 	 *	share the same interrupt line.
2392 	 */
2393 
2394 
2395 #if defined(PCIC_DEBUG)
2396 	pcic_err(pcic->dip, 0xf,
2397 	    "pcic_intr: pc_intr_mode=%d pc_type=%x io_ints=0x%x\n",
2398 	    pcic->pc_intr_mode, pcic->pc_type, io_ints);
2399 #endif
2400 
2401 	if (io_ints) {
2402 		if (pcic_do_io_intr(pcic, io_ints) == DDI_INTR_CLAIMED)
2403 			ret = DDI_INTR_CLAIMED;
2404 	}
2405 
2406 	mutex_exit(&pcic->intr_lock);
2407 
2408 #if defined(PCIC_DEBUG)
2409 	pcic_err(pcic->dip, 0xf,
2410 	    "pcic_intr: ret=%d value=%d DDI_INTR_CLAIMED=%d\n",
2411 	    ret, value, DDI_INTR_CLAIMED);
2412 #endif
2413 
2414 	return (ret);
2415 }
2416 
2417 /*
2418  * pcic_change()
2419  *	check to see if this socket had a change in state
2420  *	by checking the status change register
2421  */
2422 static int
2423 pcic_change(pcicdev_t *pcic, int socket)
2424 {
2425 	return (pcic_getb(pcic, socket, PCIC_CARD_STATUS_CHANGE));
2426 }
2427 
2428 /*
2429  * pcic_do_io_intr - calls client interrupt handlers
2430  */
2431 static int
2432 pcic_do_io_intr(pcicdev_t *pcic, uint32_t sockets)
2433 {
2434 	inthandler_t *tmp;
2435 	int ret = DDI_INTR_UNCLAIMED;
2436 
2437 #if defined(PCIC_DEBUG)
2438 	pcic_err(pcic->dip, 0xf,
2439 		"pcic_do_io_intr: pcic=%p sockets=%d irq_top=%p\n",
2440 		(void *)pcic, (int)sockets, (void *)pcic->irq_top);
2441 #endif
2442 
2443 	if (pcic->irq_top != NULL) {
2444 	    tmp = pcic->irq_current;
2445 
2446 	    do {
2447 		int cur = pcic->irq_current->socket;
2448 		pcic_socket_t *sockp =
2449 				&pcic->pc_sockets[cur];
2450 
2451 #if defined(PCIC_DEBUG)
2452 		pcic_err(pcic->dip, 0xf,
2453 		    "\t pcs_flags=0x%x PCS_CARD_PRESENT=0x%x\n",
2454 		    sockp->pcs_flags, PCS_CARD_PRESENT);
2455 		pcic_err(pcic->dip, 0xf,
2456 		    "\t sockets=%d cur=%d intr=%p arg1=%p "
2457 		    "arg2=%p\n",
2458 		    sockets, cur, (void *)pcic->irq_current->intr,
2459 		    pcic->irq_current->arg1,
2460 		    pcic->irq_current->arg2);
2461 #endif
2462 		if ((sockp->pcs_flags & PCS_CARD_PRESENT) &&
2463 		    !(sockp->pcs_flags & PCS_DEBOUNCING) &&
2464 		    (sockets & (1 << cur))) {
2465 
2466 			if ((*pcic->irq_current->intr)(pcic->irq_current->arg1,
2467 			    pcic->irq_current->arg2) == DDI_INTR_CLAIMED)
2468 				ret = DDI_INTR_CLAIMED;
2469 
2470 #if defined(PCIC_DEBUG)
2471 			pcic_err(pcic->dip, 0xf,
2472 			    "\t ret=%d DDI_INTR_CLAIMED=%d\n",
2473 			    ret, DDI_INTR_CLAIMED);
2474 #endif
2475 		}
2476 
2477 
2478 		if ((pcic->irq_current = pcic->irq_current->next) == NULL)
2479 					pcic->irq_current = pcic->irq_top;
2480 
2481 	    } while (pcic->irq_current != tmp);
2482 
2483 	    if ((pcic->irq_current = pcic->irq_current->next) == NULL)
2484 					pcic->irq_current = pcic->irq_top;
2485 
2486 	} else {
2487 		ret = DDI_INTR_UNCLAIMED;
2488 	}
2489 
2490 #if defined(PCIC_DEBUG)
2491 	pcic_err(pcic->dip, 0xf,
2492 		"pcic_do_io_intr: exit ret=%d DDI_INTR_CLAIMED=%d\n",
2493 		ret, DDI_INTR_CLAIMED);
2494 #endif
2495 
2496 	return (ret);
2497 
2498 }
2499 
2500 /*
2501  * pcic_inquire_adapter()
2502  *	SocketServices InquireAdapter function
2503  *	get characteristics of the physical adapter
2504  */
2505 /*ARGSUSED*/
2506 static int
2507 pcic_inquire_adapter(dev_info_t *dip, inquire_adapter_t *config)
2508 {
2509 	anp_t *anp = ddi_get_driver_private(dip);
2510 	pcicdev_t *pcic = anp->an_private;
2511 
2512 	config->NumSockets = pcic->pc_numsockets;
2513 	config->NumWindows = pcic->pc_numsockets * PCIC_NUMWINSOCK;
2514 	config->NumEDCs = 0;
2515 	config->AdpCaps = 0;
2516 	config->ActiveHigh = 0;
2517 	config->ActiveLow = PCIC_AVAIL_IRQS;
2518 	config->NumPower = pcic->pc_numpower;
2519 	config->power_entry = pcic->pc_power; /* until we resolve this */
2520 #if defined(PCIC_DEBUG)
2521 	if (pcic_debug) {
2522 		cmn_err(CE_CONT, "pcic_inquire_adapter:\n");
2523 		cmn_err(CE_CONT, "\tNumSockets=%d\n", config->NumSockets);
2524 		cmn_err(CE_CONT, "\tNumWindows=%d\n", config->NumWindows);
2525 	}
2526 #endif
2527 	config->ResourceFlags = 0;
2528 	switch (pcic->pc_intr_mode) {
2529 	case PCIC_INTR_MODE_PCI_1:
2530 		config->ResourceFlags |= RES_OWN_IRQ | RES_IRQ_NEXUS |
2531 			RES_IRQ_SHAREABLE;
2532 		break;
2533 	}
2534 	return (SUCCESS);
2535 }
2536 
2537 /*
2538  * pcic_callback()
2539  *	The PCMCIA nexus calls us via this function
2540  *	in order to set the callback function we are
2541  *	to call the nexus with
2542  */
2543 /*ARGSUSED*/
2544 static int
2545 pcic_callback(dev_info_t *dip, int (*handler)(), int arg)
2546 {
2547 	anp_t *anp = ddi_get_driver_private(dip);
2548 	pcicdev_t *pcic = anp->an_private;
2549 
2550 	if (handler != NULL) {
2551 		pcic->pc_callback = handler;
2552 		pcic->pc_cb_arg  = arg;
2553 		pcic->pc_flags |= PCF_CALLBACK;
2554 	} else {
2555 		pcic->pc_callback = NULL;
2556 		pcic->pc_cb_arg = 0;
2557 		pcic->pc_flags &= ~PCF_CALLBACK;
2558 	}
2559 	/*
2560 	 * we're now registered with the nexus
2561 	 * it is acceptable to do callbacks at this point.
2562 	 * don't call back from here though since it could block
2563 	 */
2564 	return (PC_SUCCESS);
2565 }
2566 
2567 /*
2568  * pcic_calc_speed (pcicdev_t *pcic, uint32_t speed)
2569  *	calculate the speed bits from the specified memory speed
2570  *	there may be more to do here
2571  */
2572 
2573 static int
2574 pcic_calc_speed(pcicdev_t *pcic, uint32_t speed)
2575 {
2576 	uint32_t wspeed = 1;	/* assume 1 wait state when unknown */
2577 	uint32_t bspeed = PCIC_ISA_DEF_SYSCLK;
2578 
2579 	switch (pcic->pc_type) {
2580 	    case PCIC_I82365SL:
2581 	    case PCIC_VADEM:
2582 	    case PCIC_VADEM_VG469:
2583 	    default:
2584 		/* Intel chip wants it in waitstates */
2585 		wspeed = mhztons(PCIC_ISA_DEF_SYSCLK) * 3;
2586 		if (speed <= wspeed)
2587 			wspeed = 0;
2588 		else if (speed <= (wspeed += mhztons(bspeed)))
2589 			wspeed = 1;
2590 		else if (speed <= (wspeed += mhztons(bspeed)))
2591 			wspeed = 2;
2592 		else
2593 			wspeed = 3;
2594 		wspeed <<= 6; /* put in right bit positions */
2595 		break;
2596 
2597 	    case PCIC_INTEL_i82092:
2598 		wspeed = SYSMEM_82092_80NS;
2599 		if (speed > 80)
2600 		    wspeed = SYSMEM_82092_100NS;
2601 		if (speed > 100)
2602 		    wspeed = SYSMEM_82092_150NS;
2603 		if (speed > 150)
2604 		    wspeed = SYSMEM_82092_200NS;
2605 		if (speed > 200)
2606 		    wspeed = SYSMEM_82092_250NS;
2607 		if (speed > 250)
2608 		    wspeed = SYSMEM_82092_600NS;
2609 		wspeed <<= 5;	/* put in right bit positions */
2610 		break;
2611 
2612 	} /* switch */
2613 
2614 	return (wspeed);
2615 }
2616 
2617 /*
2618  * These values are taken from the PC Card Standard Electrical Specification.
2619  * Generally the larger value is taken if 2 are possible.
2620  */
2621 static struct pcic_card_times {
2622 	uint16_t cycle;	/* Speed as found in the atribute space of he card. */
2623 	uint16_t setup;	/* Corresponding address setup time. */
2624 	uint16_t width;	/* Corresponding width, OE or WE. */
2625 	uint16_t hold;	/* Corresponding data or address hold time. */
2626 } pcic_card_times[] = {
2627 
2628 /*
2629  * Note: The rounded up times for 250, 200 & 150 have been increased
2630  * due to problems with the 3-Com ethernet cards (pcelx) on UBIIi.
2631  * See BugID 00663.
2632  */
2633 
2634 /*
2635  * Rounded up times           Original times from
2636  * that add up to the         the PCMCIA Spec.
2637  * cycle time.
2638  */
2639 	{600, 180, 370, 140},	/* 100, 300,  70 */
2640 	{400, 120, 300, 90},	/* Made this one up */
2641 	{250, 100, 190, 70},	/*  30, 150,  30 */
2642 	{200, 80, 170, 70},	/*  20, 120,  30 */
2643 	{150, 50, 110, 40},	/*  20,  80,  20 */
2644 	{100, 40, 80, 40},	/*  10,  60,  15 */
2645 	{0, 10, 60, 15}		/*  10,  60,  15 */
2646 };
2647 
2648 /*
2649  * pcic_set_cdtimers
2650  *	This is specific to several Cirrus Logic chips
2651  */
2652 static void
2653 pcic_set_cdtimers(pcicdev_t *pcic, int socket, uint32_t speed, int tset)
2654 {
2655 	int cmd, set, rec, offset, clk_pulse;
2656 	struct pcic_card_times *ctp;
2657 
2658 	if ((tset == IOMEM_CLTIMER_SET_1) || (tset == SYSMEM_CLTIMER_SET_1))
2659 		offset = 3;
2660 	else
2661 		offset = 0;
2662 
2663 	clk_pulse = mhztons(pcic->bus_speed);
2664 	for (ctp = pcic_card_times; speed < ctp->cycle; ctp++);
2665 
2666 	/*
2667 	 * Add (clk_pulse/2) and an extra 1 to account for rounding errors.
2668 	 */
2669 	set = ((ctp->setup + 10 + 1 + (clk_pulse/2))/clk_pulse) - 1;
2670 	if (set < 0)
2671 		set = 0;
2672 
2673 	cmd = ((ctp->width + 10 + 1 + (clk_pulse/2))/clk_pulse) - 1;
2674 	if (cmd < 0)
2675 		cmd = 0;
2676 
2677 	rec = ((ctp->hold + 10 + 1 + (clk_pulse/2))/clk_pulse) - 2;
2678 	if (rec < 0)
2679 		rec = 0;
2680 
2681 #if defined(PCIC_DEBUG)
2682 	pcic_err(pcic->dip, 8, "pcic_set_cdtimers(%d, Timer Set %d)\n"
2683 	    "ct=%d, cp=%d, cmd=0x%x, setup=0x%x, rec=0x%x\n",
2684 	    (unsigned)speed, offset == 3 ? 1 : 0,
2685 	    ctp->cycle, clk_pulse, cmd, set, rec);
2686 #endif
2687 
2688 	pcic_putb(pcic, socket, PCIC_TIME_COMMAND_0 + offset, cmd);
2689 	pcic_putb(pcic, socket, PCIC_TIME_SETUP_0 + offset, set);
2690 	pcic_putb(pcic, socket, PCIC_TIME_RECOVER_0 + offset, rec);
2691 }
2692 
2693 /*
2694  * pcic_set_window
2695  *	essentially the same as the Socket Services specification
2696  *	We use socket and not adapter since they are identifiable
2697  *	but the rest is the same
2698  *
2699  *	dip	pcic driver's device information
2700  *	window	parameters for the request
2701  */
2702 static int
2703 pcic_set_window(dev_info_t *dip, set_window_t *window)
2704 {
2705 	anp_t *anp = ddi_get_driver_private(dip);
2706 	pcicdev_t *pcic = anp->an_private;
2707 	int select;
2708 	int socket, pages, which, ret;
2709 	pcic_socket_t *sockp = &pcic->pc_sockets[window->socket];
2710 	ra_return_t res;
2711 	ndi_ra_request_t req;
2712 	uint32_t base = window->base;
2713 
2714 #if defined(PCIC_DEBUG)
2715 	if (pcic_debug) {
2716 		cmn_err(CE_CONT, "pcic_set_window: entered\n");
2717 		cmn_err(CE_CONT,
2718 			"\twindow=%d, socket=%d, WindowSize=%d, speed=%d\n",
2719 			window->window, window->socket, window->WindowSize,
2720 			window->speed);
2721 		cmn_err(CE_CONT,
2722 			"\tbase=%x, state=%x\n", (unsigned)window->base,
2723 			(unsigned)window->state);
2724 	}
2725 #endif
2726 
2727 	/*
2728 	 * do some basic sanity checking on what we support
2729 	 * we don't do paged mode
2730 	 */
2731 	if (window->state & WS_PAGED) {
2732 		cmn_err(CE_WARN, "pcic_set_window: BAD_ATTRIBUTE\n");
2733 		return (BAD_ATTRIBUTE);
2734 	}
2735 
2736 	/*
2737 	 * we don't care about previous mappings.
2738 	 * Card Services will deal with that so don't
2739 	 * even check
2740 	 */
2741 
2742 	socket = window->socket;
2743 
2744 	if (!(window->state & WS_IO)) {
2745 		int win, tmp;
2746 		pcs_memwin_t *memp;
2747 #if defined(PCIC_DEBUG)
2748 		if (pcic_debug)
2749 			cmn_err(CE_CONT, "\twindow type is memory\n");
2750 #endif
2751 		/* this is memory window mapping */
2752 		win = window->window % PCIC_NUMWINSOCK;
2753 		tmp = window->window / PCIC_NUMWINSOCK;
2754 
2755 		/* only windows 2-6 can do memory mapping */
2756 		if (tmp != window->socket || win < PCIC_IOWINDOWS) {
2757 			cmn_err(CE_CONT,
2758 				"\tattempt to map to non-mem window\n");
2759 			return (BAD_WINDOW);
2760 		}
2761 
2762 		if (window->WindowSize == 0)
2763 			window->WindowSize = MEM_MIN;
2764 		else if ((window->WindowSize & (PCIC_PAGE-1)) != 0) {
2765 			cmn_err(CE_WARN, "pcic_set_window: BAD_SIZE\n");
2766 			return (BAD_SIZE);
2767 		}
2768 
2769 		mutex_enter(&pcic->pc_lock); /* protect the registers */
2770 
2771 		memp = &sockp->pcs_windows[win].mem;
2772 		memp->pcw_speed = window->speed;
2773 
2774 		win -= PCIC_IOWINDOWS; /* put in right range */
2775 
2776 		if (window->WindowSize != memp->pcw_len)
2777 			which = memp->pcw_len;
2778 		else
2779 			which = 0;
2780 
2781 		if (window->state & WS_ENABLED) {
2782 			uint32_t wspeed;
2783 #if defined(PCIC_DEBUG)
2784 			if (pcic_debug) {
2785 				cmn_err(CE_CONT,
2786 					"\tbase=%x, win=%d\n", (unsigned)base,
2787 					win);
2788 				if (which)
2789 					cmn_err(CE_CONT,
2790 						"\tneed to remap window\n");
2791 			}
2792 #endif
2793 
2794 			if (which && (memp->pcw_status & PCW_MAPPED)) {
2795 				ddi_regs_map_free(&memp->pcw_handle);
2796 				res.ra_addr_lo = memp->pcw_base;
2797 				res.ra_len = memp->pcw_len;
2798 				(void) pcmcia_free_mem(dip, &res);
2799 				memp->pcw_status &= ~(PCW_MAPPED|PCW_ENABLED);
2800 				memp->pcw_hostmem = NULL;
2801 				memp->pcw_base = NULL;
2802 				memp->pcw_len = 0;
2803 			}
2804 
2805 			which = window->WindowSize >> PAGE_SHIFT;
2806 
2807 			if (!(memp->pcw_status & PCW_MAPPED)) {
2808 				ret = 0;
2809 
2810 				memp->pcw_base = base;
2811 				bzero(&req, sizeof (req));
2812 				req.ra_len = which << PAGE_SHIFT;
2813 				req.ra_addr = (uint64_t)memp->pcw_base;
2814 				req.ra_boundbase = pcic->pc_base;
2815 				req.ra_boundlen  = pcic->pc_bound;
2816 				req.ra_flags = (memp->pcw_base ?
2817 					NDI_RA_ALLOC_SPECIFIED : 0) |
2818 					NDI_RA_ALLOC_BOUNDED;
2819 				req.ra_align_mask =
2820 					(PAGESIZE - 1) | (PCIC_PAGE - 1);
2821 #if defined(PCIC_DEBUG)
2822 				    pcic_err(dip, 8,
2823 					    "\tlen 0x%"PRIx64
2824 					    "addr 0x%"PRIx64"bbase 0x%"PRIx64
2825 					    " blen 0x%"PRIx64" flags 0x%x"
2826 					    " algn 0x%"PRIx64"\n",
2827 					    req.ra_len, req.ra_addr,
2828 					    req.ra_boundbase,
2829 					    req.ra_boundlen, req.ra_flags,
2830 					    req.ra_align_mask);
2831 #endif
2832 
2833 				ret = pcmcia_alloc_mem(dip, &req, &res);
2834 				if (ret == DDI_FAILURE) {
2835 					mutex_exit(&pcic->pc_lock);
2836 					cmn_err(CE_WARN,
2837 					"\tpcmcia_alloc_mem() failed\n");
2838 					return (BAD_SIZE);
2839 				}
2840 				memp->pcw_base = res.ra_addr_lo;
2841 				base = memp->pcw_base;
2842 
2843 #if defined(PCIC_DEBUG)
2844 				if (pcic_debug)
2845 					cmn_err(CE_CONT,
2846 						"\tsetwindow: new base=%x\n",
2847 						(unsigned)memp->pcw_base);
2848 #endif
2849 				memp->pcw_len = window->WindowSize;
2850 
2851 				which = pcmcia_map_reg(pcic->dip,
2852 						window->child,
2853 						&res,
2854 						(uint32_t)(window->state &
2855 						    0xffff) |
2856 						    (window->socket << 16),
2857 						(caddr_t *)&memp->pcw_hostmem,
2858 						&memp->pcw_handle,
2859 						&window->attr, NULL);
2860 
2861 				if (which != DDI_SUCCESS) {
2862 
2863 					cmn_err(CE_WARN, "\tpcmcia_map_reg() "
2864 						"failed\n");
2865 
2866 				    res.ra_addr_lo = memp->pcw_base;
2867 				    res.ra_len = memp->pcw_len;
2868 				    (void) pcmcia_free_mem(pcic->dip, &res);
2869 
2870 				    mutex_exit(&pcic->pc_lock);
2871 
2872 				    return (BAD_WINDOW);
2873 				}
2874 				memp->pcw_status |= PCW_MAPPED;
2875 #if defined(PCIC_DEBUG)
2876 				if (pcic_debug)
2877 					cmn_err(CE_CONT,
2878 						"\tmap=%x, hostmem=%p\n",
2879 						which,
2880 						(void *)memp->pcw_hostmem);
2881 #endif
2882 			} else {
2883 				base = memp->pcw_base;
2884 			}
2885 
2886 			/* report the handle back to caller */
2887 			window->handle = memp->pcw_handle;
2888 
2889 #if defined(PCIC_DEBUG)
2890 			if (pcic_debug) {
2891 				cmn_err(CE_CONT,
2892 					"\twindow mapped to %x@%x len=%d\n",
2893 					(unsigned)window->base,
2894 					(unsigned)memp->pcw_base,
2895 					memp->pcw_len);
2896 			}
2897 #endif
2898 
2899 			/* find the register set offset */
2900 			select = win * PCIC_MEM_1_OFFSET;
2901 #if defined(PCIC_DEBUG)
2902 			if (pcic_debug)
2903 				cmn_err(CE_CONT, "\tselect=%x\n", select);
2904 #endif
2905 
2906 			/*
2907 			 * at this point, the register window indicator has
2908 			 * been converted to be an offset from the first
2909 			 * set of registers that are used for programming
2910 			 * the window mapping and the offset used to select
2911 			 * the correct set of registers to access the
2912 			 * specified socket.  This allows basing everything
2913 			 * off the _0 window
2914 			 */
2915 
2916 			/* map the physical page base address */
2917 			which = (window->state & WS_16BIT) ? SYSMEM_DATA_16 : 0;
2918 			which |= (window->speed <= MEM_SPEED_MIN) ?
2919 				SYSMEM_ZERO_WAIT : 0;
2920 
2921 			/* need to select register set */
2922 			select = PCIC_MEM_1_OFFSET * win;
2923 
2924 			pcic_putb(pcic, socket,
2925 					PCIC_SYSMEM_0_STARTLOW + select,
2926 					SYSMEM_LOW(base));
2927 			pcic_putb(pcic, socket,
2928 					PCIC_SYSMEM_0_STARTHI + select,
2929 					SYSMEM_HIGH(base) | which);
2930 
2931 			/*
2932 			 * Some adapters can decode window addresses greater
2933 			 * than 16-bits worth, so handle them here.
2934 			 */
2935 			switch (pcic->pc_type) {
2936 			case PCIC_INTEL_i82092:
2937 				pcic_putb(pcic, socket,
2938 						PCIC_82092_CPAGE,
2939 						SYSMEM_EXT(base));
2940 				break;
2941 			case PCIC_CL_PD6729:
2942 			case PCIC_CL_PD6730:
2943 				clext_reg_write(pcic, socket,
2944 						PCIC_CLEXT_MMAP0_UA + win,
2945 						SYSMEM_EXT(base));
2946 				break;
2947 			case PCIC_TI_PCI1130:
2948 				/*
2949 				 * Note that the TI chip has one upper byte
2950 				 * per socket so all windows get bound to a
2951 				 * 16MB segment.  This must be detected and
2952 				 * handled appropriately.  We can detect that
2953 				 * it is done by seeing if the pc_base has
2954 				 * changed and changing when the register
2955 				 * is first set.  This will force the bounds
2956 				 * to be correct.
2957 				 */
2958 				if (pcic->pc_bound == 0xffffffff) {
2959 					pcic_putb(pcic, socket,
2960 						    PCIC_TI_WINDOW_PAGE_PCI,
2961 						    SYSMEM_EXT(base));
2962 					pcic->pc_base = SYSMEM_EXT(base) << 24;
2963 					pcic->pc_bound = 0x1000000;
2964 				}
2965 				break;
2966 			case PCIC_TI_PCI1031:
2967 			case PCIC_TI_PCI1131:
2968 			case PCIC_TI_PCI1250:
2969 			case PCIC_TI_PCI1225:
2970 			case PCIC_TI_PCI1221:
2971 			case PCIC_SMC_34C90:
2972 			case PCIC_CL_PD6832:
2973 			case PCIC_RICOH_RL5C466:
2974 			case PCIC_TI_PCI1410:
2975 			case PCIC_ENE_1410:
2976 			case PCIC_TI_PCI1510:
2977 			case PCIC_TI_PCI1520:
2978 			case PCIC_O2_OZ6912:
2979 			case PCIC_TI_PCI1420:
2980 			case PCIC_ENE_1420:
2981 			case PCIC_TI_VENDOR:
2982 			case PCIC_TOSHIBA_TOPIC100:
2983 			case PCIC_TOSHIBA_TOPIC95:
2984 			case PCIC_TOSHIBA_VENDOR:
2985 			case PCIC_RICOH_VENDOR:
2986 			case PCIC_O2MICRO_VENDOR:
2987 				pcic_putb(pcic, socket,
2988 						PCIC_YENTA_MEM_PAGE + win,
2989 						SYSMEM_EXT(base));
2990 				break;
2991 			default:
2992 				cmn_err(CE_NOTE, "pcic_set_window: unknown "
2993 						"cardbus vendor:0x%X\n",
2994 						pcic->pc_type);
2995 				pcic_putb(pcic, socket,
2996 						PCIC_YENTA_MEM_PAGE + win,
2997 						SYSMEM_EXT(base));
2998 
2999 				break;
3000 			} /* switch */
3001 
3002 			/*
3003 			 * specify the length of the mapped range
3004 			 * we convert to pages (rounding up) so that
3005 			 * the hardware gets the right thing
3006 			 */
3007 			pages = (window->WindowSize+PCIC_PAGE-1)/PCIC_PAGE;
3008 
3009 			/*
3010 			 * Setup this window's timing.
3011 			 */
3012 			switch (pcic->pc_type) {
3013 			case PCIC_CL_PD6729:
3014 			case PCIC_CL_PD6730:
3015 			case PCIC_CL_PD6710:
3016 			case PCIC_CL_PD6722:
3017 				wspeed = SYSMEM_CLTIMER_SET_0;
3018 				pcic_set_cdtimers(pcic, socket,
3019 							window->speed,
3020 							wspeed);
3021 				break;
3022 
3023 			case PCIC_INTEL_i82092:
3024 			default:
3025 				wspeed = pcic_calc_speed(pcic, window->speed);
3026 				break;
3027 			} /* switch */
3028 
3029 #if defined(PCIC_DEBUG)
3030 			if (pcic_debug)
3031 				cmn_err(CE_CONT,
3032 					"\twindow %d speed bits = %x for "
3033 					"%dns\n",
3034 					win, (unsigned)wspeed, window->speed);
3035 #endif
3036 
3037 			pcic_putb(pcic, socket, PCIC_SYSMEM_0_STOPLOW + select,
3038 					SYSMEM_LOW(base +
3039 						    (pages * PCIC_PAGE)-1));
3040 
3041 			wspeed |= SYSMEM_HIGH(base + (pages * PCIC_PAGE)-1);
3042 			pcic_putb(pcic, socket, PCIC_SYSMEM_0_STOPHI + select,
3043 					wspeed);
3044 
3045 			/*
3046 			 * now map the card's memory pages - we start with page
3047 			 * 0
3048 			 * we also default to AM -- set page might change it
3049 			 */
3050 			base = memp->pcw_base;
3051 			pcic_putb(pcic, socket,
3052 					PCIC_CARDMEM_0_LOW + select,
3053 					CARDMEM_LOW(0 - (uint32_t)base));
3054 
3055 			pcic_putb(pcic, socket,
3056 					PCIC_CARDMEM_0_HI + select,
3057 					CARDMEM_HIGH(0 - (uint32_t)base) |
3058 					CARDMEM_REG_ACTIVE);
3059 
3060 			/*
3061 			 * enable the window even though redundant
3062 			 * and SetPage may do it again.
3063 			 */
3064 			select = pcic_getb(pcic, socket,
3065 					PCIC_MAPPING_ENABLE);
3066 			select |= SYSMEM_WINDOW(win);
3067 			pcic_putb(pcic, socket, PCIC_MAPPING_ENABLE, select);
3068 			memp->pcw_offset = 0;
3069 			memp->pcw_status |= PCW_ENABLED;
3070 		} else {
3071 			/*
3072 			 * not only do we unmap the memory, the
3073 			 * window has been turned off.
3074 			 */
3075 			if (which && memp->pcw_status & PCW_MAPPED) {
3076 				ddi_regs_map_free(&memp->pcw_handle);
3077 				res.ra_addr_lo = memp->pcw_base;
3078 				res.ra_len = memp->pcw_len;
3079 				(void) pcmcia_free_mem(pcic->dip, &res);
3080 				memp->pcw_hostmem = NULL;
3081 				memp->pcw_status &= ~PCW_MAPPED;
3082 			}
3083 
3084 			/* disable current mapping */
3085 			select = pcic_getb(pcic, socket, PCIC_MAPPING_ENABLE);
3086 			select &= ~SYSMEM_WINDOW(win);
3087 			pcic_putb(pcic, socket, PCIC_MAPPING_ENABLE, select);
3088 			memp->pcw_status &= ~PCW_ENABLED;
3089 		}
3090 		memp->pcw_len = window->WindowSize;
3091 		window->handle = memp->pcw_handle;
3092 #if defined(PCIC_DEBUG)
3093 		if (pcic_debug)
3094 			xxdmp_all_regs(pcic, window->socket, -1);
3095 #endif
3096 	} else {
3097 		/*
3098 		 * This is a request for an IO window
3099 		 */
3100 		int win, tmp;
3101 		pcs_iowin_t *winp;
3102 				/* I/O windows */
3103 #if defined(PCIC_DEBUG)
3104 		if (pcic_debug)
3105 			cmn_err(CE_CONT, "\twindow type is I/O\n");
3106 #endif
3107 
3108 		/* only windows 0 and 1 can do I/O */
3109 		win = window->window % PCIC_NUMWINSOCK;
3110 		tmp = window->window / PCIC_NUMWINSOCK;
3111 
3112 		if (win >= PCIC_IOWINDOWS || tmp != window->socket) {
3113 			cmn_err(CE_WARN,
3114 				"\twindow is out of range (%d)\n",
3115 				window->window);
3116 			return (BAD_WINDOW);
3117 		}
3118 
3119 		mutex_enter(&pcic->pc_lock); /* protect the registers */
3120 
3121 		winp = &sockp->pcs_windows[win].io;
3122 		winp->pcw_speed = window->speed;
3123 		if (window->WindowSize != 1 && window->WindowSize & 1) {
3124 			/* we don't want an odd-size window */
3125 			window->WindowSize++;
3126 		}
3127 		winp->pcw_len = window->WindowSize;
3128 
3129 		if (window->state & WS_ENABLED) {
3130 			if (winp->pcw_status & PCW_MAPPED) {
3131 				ddi_regs_map_free(&winp->pcw_handle);
3132 				res.ra_addr_lo = winp->pcw_base;
3133 				res.ra_len = winp->pcw_len;
3134 				(void) pcmcia_free_io(pcic->dip, &res);
3135 				winp->pcw_status &= ~(PCW_MAPPED|PCW_ENABLED);
3136 			}
3137 
3138 			/*
3139 			 * if the I/O address wasn't allocated, allocate
3140 			 *	it now. If it was allocated, it better
3141 			 *	be free to use.
3142 			 * The winp->pcw_offset value is set and used
3143 			 *	later on if the particular adapter
3144 			 *	that we're running on has the ability
3145 			 *	to translate IO accesses to the card
3146 			 *	(such as some adapters  in the Cirrus
3147 			 *	Logic family).
3148 			 */
3149 			winp->pcw_offset = 0;
3150 
3151 			/*
3152 			 * Setup the request parameters for the
3153 			 *	requested base and length. If
3154 			 *	we're on an adapter that has
3155 			 *	IO window offset registers, then
3156 			 *	we don't need a specific base
3157 			 *	address, just a length, and then
3158 			 *	we'll cause the correct IO address
3159 			 *	to be generated on the socket by
3160 			 *	setting up the IO window offset
3161 			 *	registers.
3162 			 * For adapters that support this capability, we
3163 			 *	always use the IO window offset registers,
3164 			 *	even if the passed base/length would be in
3165 			 *	range.
3166 			 */
3167 			base = window->base;
3168 			bzero(&req, sizeof (req));
3169 			req.ra_len = window->WindowSize;
3170 
3171 			req.ra_addr = (uint64_t)
3172 				((pcic->pc_flags & PCF_IO_REMAP) ? 0 : base);
3173 			req.ra_flags = (req.ra_addr) ?
3174 						NDI_RA_ALLOC_SPECIFIED : 0;
3175 
3176 			req.ra_flags |= NDI_RA_ALIGN_SIZE;
3177 			/* need to rethink this */
3178 			req.ra_boundbase = pcic->pc_iobase;
3179 			req.ra_boundlen = pcic->pc_iobound;
3180 			req.ra_flags |= NDI_RA_ALLOC_BOUNDED;
3181 
3182 #if defined(PCIC_DEBUG)
3183 			    pcic_err(dip, 8,
3184 					"\tlen 0x%"PRIx64" addr 0x%"PRIx64
3185 					"bbase 0x%"PRIx64
3186 					"blen 0x%"PRIx64" flags 0x%x algn 0x%"
3187 					PRIx64"\n",
3188 					req.ra_len, (uint64_t)req.ra_addr,
3189 					req.ra_boundbase,
3190 					req.ra_boundlen, req.ra_flags,
3191 					req.ra_align_mask);
3192 #endif
3193 
3194 			/*
3195 			 * Try to allocate the space. If we fail this,
3196 			 *	return the appropriate error depending
3197 			 *	on whether the caller specified a
3198 			 *	specific base address or not.
3199 			 */
3200 			if (pcmcia_alloc_io(dip, &req, &res) == DDI_FAILURE) {
3201 				winp->pcw_status &= ~PCW_ENABLED;
3202 				mutex_exit(&pcic->pc_lock);
3203 				cmn_err(CE_WARN, "Failed to alloc I/O:\n"
3204 					"\tlen 0x%" PRIx64 " addr 0x%" PRIx64
3205 					"bbase 0x%" PRIx64
3206 					"blen 0x%" PRIx64 "flags 0x%x"
3207 					"algn 0x%" PRIx64 "\n",
3208 					req.ra_len, req.ra_addr,
3209 					req.ra_boundbase,
3210 					req.ra_boundlen, req.ra_flags,
3211 					req.ra_align_mask);
3212 
3213 				return (base?BAD_BASE:BAD_SIZE);
3214 			} /* pcmcia_alloc_io */
3215 
3216 			/*
3217 			 * Don't change the original base. Either we use
3218 			 * the offset registers below (PCF_IO_REMAP is set)
3219 			 * or it was allocated correctly anyway.
3220 			 */
3221 			winp->pcw_base = res.ra_addr_lo;
3222 
3223 #if defined(PCIC_DEBUG)
3224 			    pcic_err(dip, 8,
3225 				    "\tsetwindow: new base=%x orig base 0x%x\n",
3226 				    (unsigned)winp->pcw_base, base);
3227 #endif
3228 
3229 			if ((which = pcmcia_map_reg(pcic->dip,
3230 						window->child,
3231 						&res,
3232 						(uint32_t)(window->state &
3233 						    0xffff) |
3234 						    (window->socket << 16),
3235 						(caddr_t *)&winp->pcw_hostmem,
3236 						&winp->pcw_handle,
3237 						&window->attr,
3238 						base)) != DDI_SUCCESS) {
3239 
3240 					cmn_err(CE_WARN, "pcmcia_map_reg()"
3241 						"failed\n");
3242 
3243 				    res.ra_addr_lo = winp->pcw_base;
3244 				    res.ra_len = winp->pcw_len;
3245 				    (void) pcmcia_free_io(pcic->dip, &res);
3246 
3247 				    mutex_exit(&pcic->pc_lock);
3248 				    return (BAD_WINDOW);
3249 			}
3250 
3251 			window->handle = winp->pcw_handle;
3252 			winp->pcw_status |= PCW_MAPPED;
3253 
3254 			/* find the register set offset */
3255 			select = win * PCIC_IO_OFFSET;
3256 
3257 #if defined(PCIC_DEBUG)
3258 			if (pcic_debug) {
3259 				cmn_err(CE_CONT,
3260 					"\tenable: window=%d, select=%x, "
3261 					"base=%x, handle=%p\n",
3262 					win, select,
3263 					(unsigned)window->base,
3264 					(void *)window->handle);
3265 			}
3266 #endif
3267 			/*
3268 			 * at this point, the register window indicator has
3269 			 * been converted to be an offset from the first
3270 			 * set of registers that are used for programming
3271 			 * the window mapping and the offset used to select
3272 			 * the correct set of registers to access the
3273 			 * specified socket.  This allows basing everything
3274 			 * off the _0 window
3275 			 */
3276 
3277 			/* map the I/O base in */
3278 			pcic_putb(pcic, socket,
3279 					PCIC_IO_ADDR_0_STARTLOW + select,
3280 					LOW_BYTE((uint32_t)winp->pcw_base));
3281 			pcic_putb(pcic, socket,
3282 					PCIC_IO_ADDR_0_STARTHI + select,
3283 					HIGH_BYTE((uint32_t)winp->pcw_base));
3284 
3285 			pcic_putb(pcic, socket,
3286 					PCIC_IO_ADDR_0_STOPLOW + select,
3287 					LOW_BYTE((uint32_t)winp->pcw_base +
3288 						window->WindowSize - 1));
3289 			pcic_putb(pcic, socket,
3290 					PCIC_IO_ADDR_0_STOPHI + select,
3291 					HIGH_BYTE((uint32_t)winp->pcw_base +
3292 						window->WindowSize - 1));
3293 
3294 			/*
3295 			 * We've got the requested IO space, now see if we
3296 			 *	need to adjust the IO window offset registers
3297 			 *	so that the correct IO address is generated
3298 			 *	at the socket. If this window doesn't have
3299 			 *	this capability, then we're all done setting
3300 			 *	up the IO resources.
3301 			 */
3302 			if (pcic->pc_flags & PCF_IO_REMAP) {
3303 
3304 
3305 				/*
3306 				 * Note that only 16 bits are used to program
3307 				 * the registers but leave 32 bits on pcw_offset
3308 				 * so that we can generate the original base
3309 				 * in get_window()
3310 				 */
3311 				winp->pcw_offset = (base - winp->pcw_base);
3312 
3313 				pcic_putb(pcic, socket,
3314 					PCIC_IO_OFFSET_LOW +
3315 					(win * PCIC_IO_OFFSET_OFFSET),
3316 					winp->pcw_offset & 0x0ff);
3317 				pcic_putb(pcic, socket,
3318 					PCIC_IO_OFFSET_HI +
3319 					(win * PCIC_IO_OFFSET_OFFSET),
3320 					(winp->pcw_offset >> 8) & 0x0ff);
3321 
3322 			} /* PCF_IO_REMAP */
3323 
3324 			/* now get the other details (size, etc) right */
3325 
3326 			/*
3327 			 * Set the data size control bits here. Most of the
3328 			 *	adapters will ignore IOMEM_16BIT when
3329 			 *	IOMEM_IOCS16 is set, except for the Intel
3330 			 *	82092, which only pays attention to the
3331 			 *	IOMEM_16BIT bit. Sigh... Intel can't even
3332 			 *	make a proper clone of their own chip.
3333 			 * The 82092 also apparently can't set the timing
3334 			 *	of I/O windows.
3335 			 */
3336 			which = (window->state & WS_16BIT) ?
3337 					(IOMEM_16BIT | IOMEM_IOCS16) : 0;
3338 
3339 			switch (pcic->pc_type) {
3340 			case PCIC_CL_PD6729:
3341 			case PCIC_CL_PD6730:
3342 			case PCIC_CL_PD6710:
3343 			case PCIC_CL_PD6722:
3344 			case PCIC_CL_PD6832:
3345 				/*
3346 				 * Select Timer Set 1 - this will take
3347 				 *	effect when the PCIC_IO_CONTROL
3348 				 *	register is written to later on;
3349 				 *	the call to pcic_set_cdtimers
3350 				 *	just sets up the timer itself.
3351 				 */
3352 				which |= IOMEM_CLTIMER_SET_1;
3353 				pcic_set_cdtimers(pcic, socket,
3354 							window->speed,
3355 							IOMEM_CLTIMER_SET_1);
3356 				which |= IOMEM_IOCS16;
3357 				break;
3358 			case PCIC_TI_PCI1031:
3359 
3360 				if (window->state & WS_16BIT)
3361 				    which |= IOMEM_WAIT16;
3362 
3363 				break;
3364 			case PCIC_TI_PCI1130:
3365 
3366 				if (window->state & WS_16BIT)
3367 				    which |= IOMEM_WAIT16;
3368 
3369 				break;
3370 			case PCIC_INTEL_i82092:
3371 				break;
3372 			default:
3373 				if (window->speed >
3374 						mhztons(pcic->bus_speed) * 3)
3375 				    which |= IOMEM_WAIT16;
3376 #ifdef notdef
3377 				if (window->speed <
3378 						mhztons(pcic->bus_speed) * 6)
3379 				    which |= IOMEM_ZERO_WAIT;
3380 #endif
3381 				break;
3382 			} /* switch (pc_type) */
3383 
3384 			/*
3385 			 * Setup the data width and timing
3386 			 */
3387 			select = pcic_getb(pcic, socket, PCIC_IO_CONTROL);
3388 			select &= ~(PCIC_IO_WIN_MASK << (win * 4));
3389 			select |= IOMEM_SETWIN(win, which);
3390 			pcic_putb(pcic, socket, PCIC_IO_CONTROL, select);
3391 
3392 			/*
3393 			 * Enable the IO window
3394 			 */
3395 			select = pcic_getb(pcic, socket, PCIC_MAPPING_ENABLE);
3396 			pcic_putb(pcic, socket, PCIC_MAPPING_ENABLE,
3397 						select | IOMEM_WINDOW(win));
3398 
3399 			winp->pcw_status |= PCW_ENABLED;
3400 
3401 #if defined(PCIC_DEBUG)
3402 			if (pcic_debug) {
3403 				cmn_err(CE_CONT,
3404 					"\twhich = %x, select = %x (%x)\n",
3405 					which, select,
3406 					IOMEM_SETWIN(win, which));
3407 				xxdmp_all_regs(pcic, window->socket * 0x40, 24);
3408 			}
3409 #endif
3410 		} else {
3411 			/*
3412 			 * not only do we unmap the IO space, the
3413 			 * window has been turned off.
3414 			 */
3415 			if (winp->pcw_status & PCW_MAPPED) {
3416 				ddi_regs_map_free(&winp->pcw_handle);
3417 				res.ra_addr_lo = winp->pcw_base;
3418 				res.ra_len = winp->pcw_len;
3419 				(void) pcmcia_free_io(pcic->dip, &res);
3420 				winp->pcw_status &= ~PCW_MAPPED;
3421 			}
3422 
3423 			/* disable current mapping */
3424 			select = pcic_getb(pcic, socket,
3425 						PCIC_MAPPING_ENABLE);
3426 			pcic_putb(pcic, socket, PCIC_MAPPING_ENABLE,
3427 					select &= ~IOMEM_WINDOW(win));
3428 			winp->pcw_status &= ~PCW_ENABLED;
3429 
3430 			winp->pcw_base = 0;
3431 			winp->pcw_len = 0;
3432 			winp->pcw_offset = 0;
3433 			window->base = 0;
3434 			/* now make sure we don't accidentally re-enable */
3435 			/* find the register set offset */
3436 			select = win * PCIC_IO_OFFSET;
3437 			pcic_putb(pcic, socket,
3438 					PCIC_IO_ADDR_0_STARTLOW + select, 0);
3439 			pcic_putb(pcic, socket,
3440 					PCIC_IO_ADDR_0_STARTHI + select, 0);
3441 			pcic_putb(pcic, socket,
3442 					PCIC_IO_ADDR_0_STOPLOW + select, 0);
3443 			pcic_putb(pcic, socket,
3444 					PCIC_IO_ADDR_0_STOPHI + select, 0);
3445 		}
3446 	}
3447 	mutex_exit(&pcic->pc_lock);
3448 
3449 	return (SUCCESS);
3450 }
3451 
3452 /*
3453  * pcic_card_state()
3454  *	compute the instantaneous Card State information
3455  */
3456 static int
3457 pcic_card_state(pcicdev_t *pcic, pcic_socket_t *sockp)
3458 {
3459 	int value, result;
3460 #if defined(PCIC_DEBUG)
3461 	int orig_value;
3462 #endif
3463 
3464 	mutex_enter(&pcic->pc_lock); /* protect the registers */
3465 
3466 	value = pcic_getb(pcic, sockp->pcs_socket, PCIC_INTERFACE_STATUS);
3467 
3468 #if defined(PCIC_DEBUG)
3469 	orig_value = value;
3470 	if (pcic_debug >= 8)
3471 		cmn_err(CE_CONT, "pcic_card_state(%p) if status = %b for %d\n",
3472 			(void *)sockp,
3473 			value,
3474 			"\020\1BVD1\2BVD2\3CD1\4CD2\5WP\6RDY\7PWR\10~GPI",
3475 			sockp->pcs_socket);
3476 #endif
3477 	/*
3478 	 * Lie to socket services if we are not ready.
3479 	 * This is when we are starting up or during debounce timeouts
3480 	 * or if the card is a cardbus card.
3481 	 */
3482 	if (!(sockp->pcs_flags & (PCS_STARTING|PCS_CARD_ISCARDBUS)) &&
3483 	    !sockp->pcs_debounce_id &&
3484 	    (value & PCIC_ISTAT_CD_MASK) == PCIC_CD_PRESENT_OK) {
3485 		result = SBM_CD;
3486 
3487 		if (value & PCIC_WRITE_PROTECT || !(value & PCIC_POWER_ON))
3488 			result |= SBM_WP;
3489 		if (value & PCIC_POWER_ON) {
3490 			if (value & PCIC_READY)
3491 				result |= SBM_RDYBSY;
3492 			value = (~value) & (PCIC_BVD1 | PCIC_BVD2);
3493 			if (value & PCIC_BVD1)
3494 				result |= SBM_BVD1;
3495 			if (value & PCIC_BVD2)
3496 				result |= SBM_BVD2;
3497 		}
3498 	} else
3499 		result = 0;
3500 
3501 	mutex_exit(&pcic->pc_lock);
3502 
3503 #if defined(PCIC_DEBUG)
3504 	pcic_err(pcic->dip, 8,
3505 	    "pcic_card_state(%p) if status = %b for %d (rval=0x%x)\n",
3506 	    (void *) sockp, orig_value,
3507 	    "\020\1BVD1\2BVD2\3CD1\4CD2\5WP\6RDY\7PWR\10~GPI",
3508 	    sockp->pcs_socket, result);
3509 #endif
3510 
3511 	return (result);
3512 }
3513 
3514 /*
3515  * pcic_set_page()
3516  *	SocketServices SetPage function
3517  *	set the page of PC Card memory that should be in the mapped
3518  *	window
3519  */
3520 /*ARGSUSED*/
3521 static int
3522 pcic_set_page(dev_info_t *dip, set_page_t *page)
3523 {
3524 	anp_t *anp = ddi_get_driver_private(dip);
3525 	pcicdev_t *pcic = anp->an_private;
3526 	int select;
3527 	int which, socket, window;
3528 	uint32_t base;
3529 	pcs_memwin_t *memp;
3530 
3531 	/* get real socket/window numbers */
3532 	window = page->window % PCIC_NUMWINSOCK;
3533 	socket = page->window / PCIC_NUMWINSOCK;
3534 
3535 #if defined(PCIC_DEBUG)
3536 	if (pcic_debug) {
3537 		cmn_err(CE_CONT,
3538 			"pcic_set_page: window=%d, socket=%d, page=%d\n",
3539 			window, socket, page->page);
3540 	}
3541 #endif
3542 	/* only windows 2-6 work on memory */
3543 	if (window < PCIC_IOWINDOWS)
3544 		return (BAD_WINDOW);
3545 
3546 	/* only one page supported (but any size) */
3547 	if (page->page != 0)
3548 		return (BAD_PAGE);
3549 
3550 	mutex_enter(&pcic->pc_lock); /* protect the registers */
3551 
3552 	memp = &pcic->pc_sockets[socket].pcs_windows[window].mem;
3553 	window -= PCIC_IOWINDOWS;
3554 
3555 #if defined(PCIC_DEBUG)
3556 	if (pcic_debug)
3557 		cmn_err(CE_CONT, "\tpcw_base=%x, pcw_hostmem=%p, pcw_len=%x\n",
3558 			(uint32_t)memp->pcw_base,
3559 			(void *)memp->pcw_hostmem, memp->pcw_len);
3560 #endif
3561 
3562 	/* window must be enabled */
3563 	if (!(memp->pcw_status & PCW_ENABLED))
3564 		return (BAD_ATTRIBUTE);
3565 
3566 	/* find the register set offset */
3567 	select = window * PCIC_MEM_1_OFFSET;
3568 #if defined(PCIC_DEBUG)
3569 	if (pcic_debug)
3570 		cmn_err(CE_CONT, "\tselect=%x\n", select);
3571 #endif
3572 
3573 	/*
3574 	 * now map the card's memory pages - we start with page 0
3575 	 */
3576 
3577 	which = 0;		/* assume simple case */
3578 	if (page->state & PS_ATTRIBUTE) {
3579 		which |= CARDMEM_REG_ACTIVE;
3580 		memp->pcw_status |= PCW_ATTRIBUTE;
3581 	} else {
3582 		memp->pcw_status &= ~PCW_ATTRIBUTE;
3583 	}
3584 
3585 	/*
3586 	 * if caller says Write Protect, enforce it.
3587 	 */
3588 	if (page->state & PS_WP) {
3589 		which |= CARDMEM_WRITE_PROTECT;
3590 		memp->pcw_status |= PCW_WP;
3591 	} else {
3592 		memp->pcw_status &= ~PCW_WP;
3593 	}
3594 #if defined(PCIC_DEBUG)
3595 	if (pcic_debug) {
3596 		cmn_err(CE_CONT, "\tmemory type = %s\n",
3597 			(which & CARDMEM_REG_ACTIVE) ? "attribute" : "common");
3598 		if (which & CARDMEM_WRITE_PROTECT)
3599 			cmn_err(CE_CONT, "\twrite protect\n");
3600 		cmn_err(CE_CONT, "\tpage offset=%x pcw_base=%x (%x)\n",
3601 			(unsigned)page->offset,
3602 			(unsigned)memp->pcw_base,
3603 			(int)page->offset - (int)memp->pcw_base & 0xffffff);
3604 	}
3605 #endif
3606 	/* address computation based on 64MB range and not larger */
3607 	base = (uint32_t)memp->pcw_base & 0x3ffffff;
3608 	pcic_putb(pcic, socket, PCIC_CARDMEM_0_LOW + select,
3609 	    CARDMEM_LOW((int)page->offset - (int)base));
3610 	(void) pcic_getb(pcic, socket, PCIC_CARDMEM_0_LOW + select);
3611 	pcic_putb(pcic, socket, PCIC_CARDMEM_0_HI + select,
3612 	    CARDMEM_HIGH((int)page->offset - base) | which);
3613 	(void) pcic_getb(pcic, socket, PCIC_CARDMEM_0_HI + select);
3614 
3615 	/*
3616 	 * while not really necessary, this just makes sure
3617 	 * nothing turned the window off behind our backs
3618 	 */
3619 	which = pcic_getb(pcic, socket, PCIC_MAPPING_ENABLE);
3620 	which |= SYSMEM_WINDOW(window);
3621 	pcic_putb(pcic, socket, PCIC_MAPPING_ENABLE, which);
3622 	(void) pcic_getb(pcic, socket, PCIC_MAPPING_ENABLE);
3623 
3624 	memp->pcw_offset = (off_t)page->offset;
3625 
3626 #if defined(PCIC_DEBUG)
3627 	if (pcic_debug) {
3628 		cmn_err(CE_CONT, "\tbase=%p, *base=%x\n",
3629 			(void *)memp->pcw_hostmem,
3630 			(uint32_t)*memp->pcw_hostmem);
3631 
3632 		xxdmp_all_regs(pcic, socket, -1);
3633 
3634 		cmn_err(CE_CONT, "\tbase=%p, *base=%x\n",
3635 			(void *)memp->pcw_hostmem,
3636 			(uint32_t)*memp->pcw_hostmem);
3637 	}
3638 #endif
3639 
3640 	if (which & PCW_ATTRIBUTE)
3641 		pcic_mswait(pcic, socket, 2);
3642 
3643 	mutex_exit(&pcic->pc_lock);
3644 
3645 	return (SUCCESS);
3646 }
3647 
3648 /*
3649  * pcic_set_vcc_level()
3650  *
3651  *	set voltage based on adapter information
3652  *
3653  *	this routine implements a limited solution for support of 3.3v cards.
3654  *	the general solution, which would fully support the pcmcia spec
3655  *	as far as allowing client drivers to request which voltage levels
3656  *	to be set, requires more framework support and driver changes - ess
3657  */
3658 static int
3659 pcic_set_vcc_level(pcicdev_t *pcic, set_socket_t *socket)
3660 {
3661 	uint32_t socket_present_state;
3662 
3663 #if defined(PCIC_DEBUG)
3664 	if (pcic_debug) {
3665 		cmn_err(CE_CONT,
3666 			"pcic_set_vcc_level(pcic=%p, VccLevel=%d)\n",
3667 			(void *)pcic, socket->VccLevel);
3668 	}
3669 #endif
3670 
3671 	/*
3672 	 * check VccLevel
3673 	 * if this is zero, power is being turned off
3674 	 * if it is non-zero, power is being turned on.
3675 	 */
3676 	if (socket->VccLevel == 0) {
3677 		return (0);
3678 	}
3679 
3680 	/*
3681 	 * range checking for sanity's sake
3682 	 */
3683 	if (socket->VccLevel >= pcic->pc_numpower) {
3684 		return (BAD_VCC);
3685 	}
3686 
3687 	switch (pcic->pc_io_type) {
3688 	/*
3689 	 * Yenta-compliant adapters have vcc info in the extended registers
3690 	 * Other adapters can be added as needed, but the 'default' case
3691 	 * has been left as it was previously so as not to break existing
3692 	 * adapters.
3693 	 */
3694 	case PCIC_IO_TYPE_YENTA:
3695 		/*
3696 		 * Here we ignore the VccLevel passed in and read the
3697 		 * card type from the adapter socket present state register
3698 		 */
3699 		socket_present_state =
3700 			ddi_get32(pcic->handle, (uint32_t *)(pcic->ioaddr +
3701 				PCIC_PRESENT_STATE_REG));
3702 #if defined(PCIC_DEBUG)
3703 		if (pcic_debug) {
3704 			cmn_err(CE_CONT,
3705 				"socket present state = 0x%x\n",
3706 				socket_present_state);
3707 		}
3708 #endif
3709 		switch (socket_present_state & PCIC_VCC_MASK) {
3710 			case PCIC_VCC_3VCARD:
3711 				/* fall through */
3712 			case PCIC_VCC_3VCARD|PCIC_VCC_5VCARD:
3713 				socket->VccLevel = PCIC_VCC_3VLEVEL;
3714 				return
3715 				    (POWER_3VCARD_ENABLE|POWER_OUTPUT_ENABLE);
3716 			case PCIC_VCC_5VCARD:
3717 				socket->VccLevel = PCIC_VCC_5VLEVEL;
3718 				return
3719 				    (POWER_CARD_ENABLE|POWER_OUTPUT_ENABLE);
3720 			default:
3721 				/*
3722 				 * if no card is present, this can be the
3723 				 * case of a client making a SetSocket call
3724 				 * after card removal. In this case we return
3725 				 * the current power level
3726 				 */
3727 				return ((unsigned)ddi_get8(pcic->handle,
3728 				    pcic->ioaddr + CB_R2_OFFSET +
3729 					PCIC_POWER_CONTROL));
3730 		}
3731 
3732 	default:
3733 
3734 		switch (socket->VccLevel) {
3735 		case PCIC_VCC_3VLEVEL:
3736 			return (BAD_VCC);
3737 		case PCIC_VCC_5VLEVEL:
3738 			/* enable Vcc */
3739 			return (POWER_CARD_ENABLE|POWER_OUTPUT_ENABLE);
3740 		default:
3741 			return (BAD_VCC);
3742 		}
3743 	}
3744 }
3745 
3746 
3747 /*
3748  * pcic_set_socket()
3749  *	Socket Services SetSocket call
3750  *	sets basic socket configuration
3751  */
3752 static int
3753 pcic_set_socket(dev_info_t *dip, set_socket_t *socket)
3754 {
3755 	anp_t *anp = ddi_get_driver_private(dip);
3756 	pcicdev_t *pcic = anp->an_private;
3757 	pcic_socket_t *sockp = &pcic->pc_sockets[socket->socket];
3758 	int irq, interrupt, mirq;
3759 	int powerlevel = 0;
3760 	int ind, value, orig_pwrctl;
3761 
3762 #if defined(PCIC_DEBUG)
3763 	if (pcic_debug) {
3764 		cmn_err(CE_CONT,
3765 		    "pcic_set_socket(dip=%p, socket=%d)"
3766 		    " Vcc=%d Vpp1=%d Vpp2=%d\n", (void *)dip,
3767 		    socket->socket, socket->VccLevel, socket->Vpp1Level,
3768 		    socket->Vpp2Level);
3769 	}
3770 #endif
3771 	/*
3772 	 * check VccLevel, etc. before setting mutex
3773 	 * if this is zero, power is being turned off
3774 	 * if it is non-zero, power is being turned on.
3775 	 * the default case is to assume Vcc only.
3776 	 */
3777 
3778 	/* this appears to be very implementation specific */
3779 
3780 	if (socket->Vpp1Level != socket->Vpp2Level)
3781 		return (BAD_VPP);
3782 
3783 	if (socket->VccLevel == 0 || !(sockp->pcs_flags & PCS_CARD_PRESENT)) {
3784 		powerlevel = 0;
3785 		sockp->pcs_vcc = 0;
3786 		sockp->pcs_vpp1 = 0;
3787 		sockp->pcs_vpp2 = 0;
3788 	} else {
3789 #if defined(PCIC_DEBUG)
3790 		pcic_err(dip, 9, "\tVcc=%d Vpp1Level=%d, Vpp2Level=%d\n",
3791 		    socket->VccLevel, socket->Vpp1Level, socket->Vpp2Level);
3792 #endif
3793 		/* valid Vcc power level? */
3794 		if (socket->VccLevel >= pcic->pc_numpower)
3795 			return (BAD_VCC);
3796 
3797 		switch (pcic_power[socket->VccLevel].PowerLevel) {
3798 		case 33:	/* 3.3V */
3799 		case 60:	/* for bad CIS in Option GPRS card */
3800 			if (!(pcic->pc_flags & PCF_33VCAP)) {
3801 				cmn_err(CE_WARN,
3802 				    "%s%d: Bad Request for 3.3V "
3803 				    "(Controller incapable)\n",
3804 				    ddi_get_name(pcic->dip),
3805 				    ddi_get_instance(pcic->dip));
3806 				return (BAD_VCC);
3807 			}
3808 			/* FALLTHROUGH */
3809 		case 50:	/* 5V */
3810 			if ((pcic->pc_io_type == PCIC_IO_TYPE_YENTA) &&
3811 			    pcic_getcb(pcic, CB_PRESENT_STATE) &
3812 			    CB_PS_33VCARD) {
3813 				/*
3814 				 * This is actually a 3.3V card.
3815 				 * Solaris Card Services
3816 				 * doesn't understand 3.3V
3817 				 * so we cheat and change
3818 				 * the setting to the one appropriate to 3.3V.
3819 				 * Note that this is the entry number
3820 				 * in the pcic_power[] array.
3821 				 */
3822 				sockp->pcs_vcc = PCIC_VCC_3VLEVEL;
3823 			} else
3824 				sockp->pcs_vcc = socket->VccLevel;
3825 			break;
3826 		default:
3827 			return (BAD_VCC);
3828 		}
3829 
3830 		/* enable Vcc */
3831 		powerlevel = POWER_CARD_ENABLE;
3832 
3833 #if defined(PCIC_DEBUG)
3834 		if (pcic_debug) {
3835 			cmn_err(CE_CONT, "\tVcc=%d powerlevel=%x\n",
3836 			    socket->VccLevel, powerlevel);
3837 		}
3838 #endif
3839 		ind = 0;		/* default index to 0 power */
3840 		if ((int)socket->Vpp1Level >= 0 &&
3841 		    socket->Vpp1Level < pcic->pc_numpower) {
3842 			if (!(pcic_power[socket->Vpp1Level].ValidSignals
3843 			    & VPP1)) {
3844 				return (BAD_VPP);
3845 			}
3846 			ind = pcic_power[socket->Vpp1Level].PowerLevel/10;
3847 			powerlevel |= pcic_vpp_levels[ind];
3848 			sockp->pcs_vpp1 = socket->Vpp1Level;
3849 		}
3850 		if ((int)socket->Vpp2Level >= 0 &&
3851 		    socket->Vpp2Level < pcic->pc_numpower) {
3852 			if (!(pcic_power[socket->Vpp2Level].ValidSignals
3853 			    & VPP2)) {
3854 				return (BAD_VPP);
3855 			}
3856 			ind = pcic_power[socket->Vpp2Level].PowerLevel/10;
3857 			powerlevel |= (pcic_vpp_levels[ind] << 2);
3858 			sockp->pcs_vpp2 = socket->Vpp2Level;
3859 		}
3860 
3861 		if (pcic->pc_flags & PCF_VPPX) {
3862 			/*
3863 			 * this adapter doesn't allow separate Vpp1/Vpp2
3864 			 * if one is turned on, both are turned on and only
3865 			 * the Vpp1 bits should be set
3866 			 */
3867 			if (sockp->pcs_vpp2 != sockp->pcs_vpp1) {
3868 				/* must be the same if one not zero */
3869 				if (sockp->pcs_vpp1 != 0 &&
3870 				    sockp->pcs_vpp2 != 0) {
3871 					cmn_err(CE_WARN,
3872 					    "%s%d: Bad Power Request "
3873 					    "(Vpp1/2 not the same)\n",
3874 					    ddi_get_name(pcic->dip),
3875 					    ddi_get_instance(pcic->dip));
3876 					return (BAD_VPP);
3877 				}
3878 			}
3879 			powerlevel &= ~(3<<2);
3880 		}
3881 
3882 #if defined(PCIC_DEBUG)
3883 		if (pcic_debug) {
3884 			cmn_err(CE_CONT, "\tpowerlevel=%x, ind=%x\n",
3885 			    powerlevel, ind);
3886 		}
3887 #endif
3888 	}
3889 	mutex_enter(&pcic->pc_lock); /* protect the registers */
3890 
3891 	/* turn socket->IREQRouting off while programming */
3892 	interrupt = pcic_getb(pcic, socket->socket, PCIC_INTERRUPT);
3893 	interrupt &= ~PCIC_INTR_MASK;
3894 	if (pcic->pc_flags & PCF_USE_SMI)
3895 		interrupt |= PCIC_INTR_ENABLE;
3896 	pcic_putb(pcic, socket->socket, PCIC_INTERRUPT, interrupt);
3897 
3898 	switch (pcic->pc_type) {
3899 	    case PCIC_INTEL_i82092:
3900 		pcic_82092_smiirq_ctl(pcic, socket->socket, PCIC_82092_CTL_IRQ,
3901 						PCIC_82092_INT_DISABLE);
3902 		break;
3903 	    default:
3904 		break;
3905 	} /* switch */
3906 
3907 	/* the SCIntMask specifies events to detect */
3908 	mirq = pcic_getb(pcic, socket->socket, PCIC_MANAGEMENT_INT);
3909 
3910 #if defined(PCIC_DEBUG)
3911 	if (pcic_debug)
3912 		cmn_err(CE_CONT,
3913 			"\tSCIntMask=%x, interrupt=%x, mirq=%x\n",
3914 			socket->SCIntMask, interrupt, mirq);
3915 #endif
3916 	mirq &= ~(PCIC_BD_DETECT|PCIC_BW_DETECT|PCIC_RD_DETECT);
3917 	pcic_putb(pcic, socket->socket, PCIC_MANAGEMENT_INT,
3918 	    mirq & ~PCIC_CHANGE_MASK);
3919 
3920 	/* save the mask we want to use */
3921 	sockp->pcs_intmask = socket->SCIntMask;
3922 
3923 	/*
3924 	 * Until there is a card present it's not worth enabling
3925 	 * any interrupts except "Card detect". This is done
3926 	 * elsewhere in the driver so don't change things if
3927 	 * there is no card!
3928 	 */
3929 	if (sockp->pcs_flags & PCS_CARD_PRESENT) {
3930 
3931 		/* now update the hardware to reflect events desired */
3932 		if (sockp->pcs_intmask & SBM_BVD1 || socket->IFType == IF_IO)
3933 			mirq |= PCIC_BD_DETECT;
3934 
3935 		if (sockp->pcs_intmask & SBM_BVD2)
3936 			mirq |= PCIC_BW_DETECT;
3937 
3938 		if (sockp->pcs_intmask & SBM_RDYBSY)
3939 			mirq |= PCIC_RD_DETECT;
3940 
3941 		if (sockp->pcs_intmask & SBM_CD)
3942 			mirq |= PCIC_CD_DETECT;
3943 	}
3944 
3945 	if (sockp->pcs_flags & PCS_READY) {
3946 		/*
3947 		 * card just came ready.
3948 		 * make sure enough time elapses
3949 		 * before touching it.
3950 		 */
3951 		sockp->pcs_flags &= ~PCS_READY;
3952 		pcic_mswait(pcic, socket->socket, 10);
3953 	}
3954 
3955 #if defined(PCIC_DEBUG)
3956 	if (pcic_debug) {
3957 		cmn_err(CE_CONT, "\tstatus change set to %x\n", mirq);
3958 	}
3959 #endif
3960 
3961 	switch (pcic->pc_type) {
3962 	    case PCIC_I82365SL:
3963 	    case PCIC_VADEM:
3964 	    case PCIC_VADEM_VG469:
3965 		/*
3966 		 * The Intel version has different options. This is a
3967 		 * special case of GPI which might be used for eject
3968 		 */
3969 
3970 		irq = pcic_getb(pcic, socket->socket, PCIC_CARD_DETECT);
3971 		if (sockp->pcs_intmask & (SBM_EJECT|SBM_INSERT) &&
3972 		    pcic->pc_flags & PCF_GPI_EJECT) {
3973 			irq |= PCIC_GPI_ENABLE;
3974 		} else {
3975 			irq &= ~PCIC_GPI_ENABLE;
3976 		}
3977 		pcic_putb(pcic, socket->socket, PCIC_CARD_DETECT, irq);
3978 		break;
3979 	    case PCIC_CL_PD6710:
3980 	    case PCIC_CL_PD6722:
3981 		if (socket->IFType == IF_IO) {
3982 			pcic_putb(pcic, socket->socket, PCIC_MISC_CTL_2, 0x0);
3983 			value = pcic_getb(pcic, socket->socket,
3984 						PCIC_MISC_CTL_1);
3985 			if (pcic->pc_flags & PCF_AUDIO)
3986 				value |= PCIC_MC_SPEAKER_ENB;
3987 			pcic_putb(pcic, socket->socket, PCIC_MISC_CTL_1,
3988 					value);
3989 		} else {
3990 			value = pcic_getb(pcic, socket->socket,
3991 						PCIC_MISC_CTL_1);
3992 			value &= ~PCIC_MC_SPEAKER_ENB;
3993 			pcic_putb(pcic, socket->socket, PCIC_MISC_CTL_1,
3994 					value);
3995 		}
3996 		break;
3997 	    case PCIC_CL_PD6729:
3998 	    case PCIC_CL_PD6730:
3999 	    case PCIC_CL_PD6832:
4000 		value = pcic_getb(pcic, socket->socket, PCIC_MISC_CTL_1);
4001 		if ((socket->IFType == IF_IO) && (pcic->pc_flags & PCF_AUDIO)) {
4002 		    value |= PCIC_MC_SPEAKER_ENB;
4003 		} else {
4004 		    value &= ~PCIC_MC_SPEAKER_ENB;
4005 		}
4006 
4007 		if (pcic_power[sockp->pcs_vcc].PowerLevel == 33)
4008 			value |= PCIC_MC_3VCC;
4009 		else
4010 			value &= ~PCIC_MC_3VCC;
4011 
4012 		pcic_putb(pcic, socket->socket, PCIC_MISC_CTL_1, value);
4013 		break;
4014 
4015 	    case PCIC_O2_OZ6912:
4016 		value = pcic_getcb(pcic, CB_MISCCTRL);
4017 		if ((socket->IFType == IF_IO) && (pcic->pc_flags & PCF_AUDIO))
4018 			value |= (1<<25);
4019 		else
4020 			value &= ~(1<<25);
4021 		pcic_putcb(pcic, CB_MISCCTRL, value);
4022 		if (pcic_power[sockp->pcs_vcc].PowerLevel == 33)
4023 			powerlevel |= 0x08;
4024 		break;
4025 
4026 	    case PCIC_TI_PCI1250:
4027 	    case PCIC_TI_PCI1221:
4028 	    case PCIC_TI_PCI1225:
4029 	    case PCIC_TI_PCI1410:
4030 	    case PCIC_ENE_1410:
4031 	    case PCIC_TI_PCI1510:
4032 	    case PCIC_TI_PCI1520:
4033 	    case PCIC_TI_PCI1420:
4034 	    case PCIC_ENE_1420:
4035 		value = ddi_get8(pcic->cfg_handle,
4036 		    pcic->cfgaddr + PCIC_CRDCTL_REG);
4037 		if ((socket->IFType == IF_IO) && (pcic->pc_flags & PCF_AUDIO)) {
4038 			value |= PCIC_CRDCTL_SPKR_ENBL;
4039 		} else {
4040 			value &= ~PCIC_CRDCTL_SPKR_ENBL;
4041 		}
4042 		ddi_put8(pcic->cfg_handle,
4043 		    pcic->cfgaddr + PCIC_CRDCTL_REG, value);
4044 		if (pcic_power[sockp->pcs_vcc].PowerLevel == 33)
4045 			powerlevel |= 0x08;
4046 		break;
4047 	}
4048 
4049 	/*
4050 	 * ctlind processing -- we can ignore this
4051 	 * there aren't any outputs on the chip for this and
4052 	 * the GUI will display what it thinks is correct
4053 	 */
4054 
4055 	/*
4056 	 * If outputs are enabled and the power is going off
4057 	 * turn off outputs first.
4058 	 */
4059 
4060 	/* power setup -- if necessary */
4061 	orig_pwrctl = pcic_getb(pcic, socket->socket, PCIC_POWER_CONTROL);
4062 	if ((orig_pwrctl & POWER_OUTPUT_ENABLE) && sockp->pcs_vcc == 0) {
4063 		orig_pwrctl &= ~POWER_OUTPUT_ENABLE;
4064 		pcic_putb(pcic, socket->socket,
4065 		    PCIC_POWER_CONTROL, orig_pwrctl);
4066 		(void) pcic_getb(pcic, socket->socket, PCIC_POWER_CONTROL);
4067 	}
4068 
4069 	if (pcic->pc_flags & PCF_CBPWRCTL) {
4070 		value = pcic_cbus_powerctl(pcic, socket->socket);
4071 		powerlevel = 0;
4072 	} else
4073 		value = pcic_exca_powerctl(pcic, socket->socket, powerlevel);
4074 
4075 	if (value != SUCCESS) {
4076 		mutex_exit(&pcic->pc_lock);
4077 		return (value);
4078 	}
4079 
4080 	/*
4081 	 * If outputs were disabled and the power is going on
4082 	 * turn on outputs afterwards.
4083 	 */
4084 	if (!(orig_pwrctl & POWER_OUTPUT_ENABLE) && sockp->pcs_vcc != 0) {
4085 		orig_pwrctl = pcic_getb(pcic, socket->socket,
4086 		    PCIC_POWER_CONTROL);
4087 		orig_pwrctl |= POWER_OUTPUT_ENABLE;
4088 		pcic_putb(pcic, socket->socket,
4089 		    PCIC_POWER_CONTROL, orig_pwrctl);
4090 		(void) pcic_getb(pcic, socket->socket, PCIC_POWER_CONTROL);
4091 	}
4092 
4093 	/*
4094 	 * Once we have done the power stuff can re-enable management
4095 	 * interrupts.
4096 	 */
4097 	pcic_putb(pcic, socket->socket, PCIC_MANAGEMENT_INT, mirq);
4098 
4099 #if defined(PCIC_DEBUG)
4100 	pcic_err(dip, 8, "\tmanagement int set to %x pwrctl to 0x%x "
4101 	    "cbctl 0x%x\n",
4102 	    mirq, pcic_getb(pcic, socket->socket, PCIC_POWER_CONTROL),
4103 	    pcic_getcb(pcic, CB_CONTROL));
4104 #endif
4105 
4106 	/* irq processing */
4107 	if (socket->IFType == IF_IO) {
4108 		/* IRQ only for I/O */
4109 		irq = socket->IREQRouting & PCIC_INTR_MASK;
4110 		value = pcic_getb(pcic, socket->socket, PCIC_INTERRUPT);
4111 		value &= ~PCIC_INTR_MASK;
4112 
4113 		/* to enable I/O operation */
4114 		value |= PCIC_IO_CARD | PCIC_RESET;
4115 		sockp->pcs_flags |= PCS_CARD_IO;
4116 		if (irq != sockp->pcs_irq) {
4117 			if (sockp->pcs_irq != 0)
4118 				cmn_err(CE_CONT,
4119 					"SetSocket: IRQ mismatch %x != %x!\n",
4120 					irq, sockp->pcs_irq);
4121 			else
4122 				sockp->pcs_irq = irq;
4123 		}
4124 		irq = sockp->pcs_irq;
4125 
4126 		pcic_putb(pcic, socket->socket, PCIC_INTERRUPT, value);
4127 		if (socket->IREQRouting & IRQ_ENABLE) {
4128 			pcic_enable_io_intr(pcic, socket->socket, irq);
4129 			sockp->pcs_flags |= PCS_IRQ_ENABLED;
4130 		} else {
4131 			pcic_disable_io_intr(pcic, socket->socket);
4132 			sockp->pcs_flags &= ~PCS_IRQ_ENABLED;
4133 		}
4134 #if defined(PCIC_DEBUG)
4135 		if (pcic_debug) {
4136 			cmn_err(CE_CONT,
4137 				"\tsocket type is I/O and irq %x is %s\n", irq,
4138 				(socket->IREQRouting & IRQ_ENABLE) ?
4139 				"enabled" : "not enabled");
4140 			xxdmp_all_regs(pcic, socket->socket, 20);
4141 		}
4142 #endif
4143 	} else {
4144 		/* make sure I/O mode is off */
4145 
4146 		sockp->pcs_irq = 0;
4147 
4148 		value = pcic_getb(pcic, socket->socket, PCIC_INTERRUPT);
4149 		value &= ~PCIC_IO_CARD;
4150 		pcic_putb(pcic, socket->socket, PCIC_INTERRUPT, value);
4151 		pcic_disable_io_intr(pcic, socket->socket);
4152 		sockp->pcs_flags &= ~(PCS_CARD_IO|PCS_IRQ_ENABLED);
4153 	}
4154 
4155 	sockp->pcs_state &= ~socket->State;
4156 
4157 	mutex_exit(&pcic->pc_lock);
4158 	return (SUCCESS);
4159 }
4160 
4161 /*
4162  * pcic_inquire_socket()
4163  *	SocketServices InquireSocket function
4164  *	returns basic characteristics of the socket
4165  */
4166 /*ARGSUSED*/
4167 static int
4168 pcic_inquire_socket(dev_info_t *dip, inquire_socket_t *socket)
4169 {
4170 	anp_t *anp = ddi_get_driver_private(dip);
4171 	pcicdev_t *pcic = anp->an_private;
4172 	int value;
4173 
4174 	socket->SCIntCaps = PCIC_DEFAULT_INT_CAPS;
4175 	socket->SCRptCaps = PCIC_DEFAULT_RPT_CAPS;
4176 	socket->CtlIndCaps = PCIC_DEFAULT_CTL_CAPS;
4177 	value = pcic->pc_sockets[socket->socket].pcs_flags;
4178 	socket->SocketCaps = (value & PCS_SOCKET_IO) ? IF_IO : IF_MEMORY;
4179 	socket->ActiveHigh = 0;
4180 	/* these are the usable IRQs */
4181 	socket->ActiveLow = 0xfff0;
4182 	return (SUCCESS);
4183 }
4184 
4185 /*
4186  * pcic_inquire_window()
4187  *	SocketServices InquireWindow function
4188  *	returns detailed characteristics of the window
4189  *	this is where windows get tied to sockets
4190  */
4191 /*ARGSUSED*/
4192 static int
4193 pcic_inquire_window(dev_info_t *dip, inquire_window_t *window)
4194 {
4195 	int type, socket;
4196 
4197 	type = window->window % PCIC_NUMWINSOCK;
4198 	socket = window->window / PCIC_NUMWINSOCK;
4199 
4200 #if defined(PCIC_DEBUG)
4201 	if (pcic_debug >= 8)
4202 		cmn_err(CE_CONT,
4203 			"pcic_inquire_window: window = %d/%d socket=%d\n",
4204 			window->window, type, socket);
4205 #endif
4206 	if (type < PCIC_IOWINDOWS) {
4207 		window->WndCaps = WC_IO|WC_WAIT;
4208 		type = IF_IO;
4209 	} else {
4210 		window->WndCaps = WC_COMMON|WC_ATTRIBUTE|WC_WAIT;
4211 		type = IF_MEMORY;
4212 	}
4213 
4214 	/* initialize the socket map - one socket per window */
4215 	PR_ZERO(window->Sockets);
4216 	PR_SET(window->Sockets, socket);
4217 
4218 	if (type == IF_IO) {
4219 		iowin_char_t *io;
4220 		io = &window->iowin_char;
4221 		io->IOWndCaps = WC_BASE|WC_SIZE|WC_WENABLE|WC_8BIT|
4222 			WC_16BIT;
4223 		io->FirstByte = (baseaddr_t)IOMEM_FIRST;
4224 		io->LastByte = (baseaddr_t)IOMEM_LAST;
4225 		io->MinSize = IOMEM_MIN;
4226 		io->MaxSize = IOMEM_MAX;
4227 		io->ReqGran = IOMEM_GRAN;
4228 		io->AddrLines = IOMEM_DECODE;
4229 		io->EISASlot = 0;
4230 	} else {
4231 		mem_win_char_t *mem;
4232 		mem = &window->mem_win_char;
4233 		mem->MemWndCaps = WC_BASE|WC_SIZE|WC_WENABLE|WC_8BIT|
4234 			WC_16BIT|WC_WP;
4235 
4236 		mem->FirstByte = (baseaddr_t)MEM_FIRST;
4237 		mem->LastByte = (baseaddr_t)MEM_LAST;
4238 
4239 		mem->MinSize = MEM_MIN;
4240 		mem->MaxSize = MEM_MAX;
4241 		mem->ReqGran = PCIC_PAGE;
4242 		mem->ReqBase = 0;
4243 		mem->ReqOffset = PCIC_PAGE;
4244 		mem->Slowest = MEM_SPEED_MAX;
4245 		mem->Fastest = MEM_SPEED_MIN;
4246 	}
4247 	return (SUCCESS);
4248 }
4249 
4250 /*
4251  * pcic_get_adapter()
4252  *	SocketServices GetAdapter function
4253  *	this is nearly a no-op.
4254  */
4255 /*ARGSUSED*/
4256 static int
4257 pcic_get_adapter(dev_info_t *dip, get_adapter_t *adapt)
4258 {
4259 	anp_t *anp = ddi_get_driver_private(dip);
4260 	pcicdev_t *pcic = anp->an_private;
4261 
4262 	if (pcic->pc_flags & PCF_INTRENAB)
4263 		adapt->SCRouting = IRQ_ENABLE;
4264 	adapt->state = 0;
4265 	return (SUCCESS);
4266 }
4267 
4268 /*
4269  * pcic_get_page()
4270  *	SocketServices GetPage function
4271  *	returns info about the window
4272  */
4273 /*ARGSUSED*/
4274 static int
4275 pcic_get_page(dev_info_t *dip, get_page_t *page)
4276 {
4277 	anp_t *anp = ddi_get_driver_private(dip);
4278 	pcicdev_t *pcic = anp->an_private;
4279 	int socket, window;
4280 	pcs_memwin_t *winp;
4281 
4282 	socket = page->window / PCIC_NUMWINSOCK;
4283 	window = page->window % PCIC_NUMWINSOCK;
4284 
4285 	/* I/O windows are the first two */
4286 	if (window < PCIC_IOWINDOWS || socket >= pcic->pc_numsockets) {
4287 		return (BAD_WINDOW);
4288 	}
4289 
4290 	winp = &pcic->pc_sockets[socket].pcs_windows[window].mem;
4291 
4292 	if (page->page != 0)
4293 		return (BAD_PAGE);
4294 
4295 	page->state = 0;
4296 	if (winp->pcw_status & PCW_ENABLED)
4297 		page->state |= PS_ENABLED;
4298 	if (winp->pcw_status & PCW_ATTRIBUTE)
4299 		page->state |= PS_ATTRIBUTE;
4300 	if (winp->pcw_status & PCW_WP)
4301 		page->state |= PS_WP;
4302 
4303 	page->offset = (off_t)winp->pcw_offset;
4304 
4305 	return (SUCCESS);
4306 }
4307 
4308 /*
4309  * pcic_get_socket()
4310  *	SocketServices GetSocket
4311  *	returns information about the current socket setting
4312  */
4313 /*ARGSUSED*/
4314 static int
4315 pcic_get_socket(dev_info_t *dip, get_socket_t *socket)
4316 {
4317 	anp_t *anp = ddi_get_driver_private(dip);
4318 	pcicdev_t *pcic = anp->an_private;
4319 	int socknum, irq_enabled;
4320 	pcic_socket_t *sockp;
4321 
4322 	socknum = socket->socket;
4323 	sockp = &pcic->pc_sockets[socknum];
4324 
4325 	socket->SCIntMask = sockp->pcs_intmask;
4326 	sockp->pcs_state = pcic_card_state(pcic, sockp);
4327 
4328 	socket->state = sockp->pcs_state;
4329 	if (socket->state & SBM_CD) {
4330 		socket->VccLevel = sockp->pcs_vcc;
4331 		socket->Vpp1Level = sockp->pcs_vpp1;
4332 		socket->Vpp2Level = sockp->pcs_vpp2;
4333 		irq_enabled = (sockp->pcs_flags & PCS_IRQ_ENABLED) ?
4334 		    IRQ_ENABLE : 0;
4335 		socket->IRQRouting = sockp->pcs_irq | irq_enabled;
4336 		socket->IFType = (sockp->pcs_flags & PCS_CARD_IO) ?
4337 		    IF_IO : IF_MEMORY;
4338 	} else {
4339 		socket->VccLevel = 0;
4340 		socket->Vpp1Level = 0;
4341 		socket->Vpp2Level = 0;
4342 		socket->IRQRouting = 0;
4343 		socket->IFType = IF_MEMORY;
4344 	}
4345 	socket->CtlInd = 0;	/* no indicators */
4346 
4347 	return (SUCCESS);
4348 }
4349 
4350 /*
4351  * pcic_get_status()
4352  *	SocketServices GetStatus
4353  *	returns status information about the PC Card in
4354  *	the selected socket
4355  */
4356 /*ARGSUSED*/
4357 static int
4358 pcic_get_status(dev_info_t *dip, get_ss_status_t *status)
4359 {
4360 	anp_t *anp = ddi_get_driver_private(dip);
4361 	pcicdev_t *pcic = anp->an_private;
4362 	int socknum, irq_enabled;
4363 	pcic_socket_t *sockp;
4364 
4365 	socknum = status->socket;
4366 	sockp = &pcic->pc_sockets[socknum];
4367 
4368 	status->CardState = pcic_card_state(pcic, sockp);
4369 	status->SocketState = sockp->pcs_state;
4370 	status->CtlInd = 0;	/* no indicators */
4371 
4372 	if (sockp->pcs_flags & PCS_CARD_PRESENT)
4373 		status->SocketState |= SBM_CD;
4374 	if (status->CardState & SBM_CD) {
4375 		irq_enabled = (sockp->pcs_flags & PCS_CARD_ENABLED) ?
4376 		    IRQ_ENABLE : 0;
4377 		status->IRQRouting = sockp->pcs_irq | irq_enabled;
4378 		status->IFType = (sockp->pcs_flags & PCS_CARD_IO) ?
4379 		    IF_IO : IF_MEMORY;
4380 	} else {
4381 		status->IRQRouting = 0;
4382 		status->IFType = IF_MEMORY;
4383 	}
4384 
4385 #if defined(PCIC_DEBUG)
4386 	if (pcic_debug >= 8)
4387 		cmn_err(CE_CONT, "pcic_get_status: socket=%d, CardState=%x,"
4388 			"SocketState=%x\n",
4389 			socknum, status->CardState, status->SocketState);
4390 #endif
4391 	switch (pcic->pc_type) {
4392 	uint32_t present_state;
4393 	case PCIC_TI_PCI1410:
4394 	case PCIC_TI_PCI1520:
4395 	case PCIC_TI_PCI1420:
4396 	case PCIC_ENE_1420:
4397 	case PCIC_TOSHIBA_TOPIC100:
4398 	case PCIC_TOSHIBA_TOPIC95:
4399 	case PCIC_TOSHIBA_VENDOR:
4400 	case PCIC_O2MICRO_VENDOR:
4401 	case PCIC_TI_VENDOR:
4402 	case PCIC_RICOH_VENDOR:
4403 		present_state = pcic_getcb(pcic, CB_PRESENT_STATE);
4404 		if (present_state & PCIC_CB_CARD)
4405 			status->IFType = IF_CARDBUS;
4406 #if defined(PCIC_DEBUG)
4407 		if (pcic_debug >= 8)
4408 		    cmn_err(CE_CONT, "pcic_get_status: present_state=0x%x\n",
4409 			present_state);
4410 #endif
4411 		break;
4412 	default:
4413 		break;
4414 	}
4415 
4416 	return (SUCCESS);
4417 }
4418 
4419 /*
4420  * pcic_get_window()
4421  *	SocketServices GetWindow function
4422  *	returns state information about the specified window
4423  */
4424 /*ARGSUSED*/
4425 static int
4426 pcic_get_window(dev_info_t *dip, get_window_t *window)
4427 {
4428 	anp_t *anp = ddi_get_driver_private(dip);
4429 	pcicdev_t *pcic = anp->an_private;
4430 	int socket, win;
4431 	pcic_socket_t *sockp;
4432 	pcs_memwin_t *winp;
4433 
4434 	socket = window->window / PCIC_NUMWINSOCK;
4435 	win = window->window % PCIC_NUMWINSOCK;
4436 #if defined(PCIC_DEBUG)
4437 	if (pcic_debug) {
4438 		cmn_err(CE_CONT, "pcic_get_window(socket=%d, window=%d)\n",
4439 			socket, win);
4440 	}
4441 #endif
4442 
4443 	if (socket > pcic->pc_numsockets)
4444 		return (BAD_WINDOW);
4445 
4446 	sockp = &pcic->pc_sockets[socket];
4447 	winp = &sockp->pcs_windows[win].mem;
4448 
4449 	window->socket = socket;
4450 	window->size = winp->pcw_len;
4451 	window->speed = winp->pcw_speed;
4452 	window->handle = (ddi_acc_handle_t)winp->pcw_handle;
4453 	window->base = (uint32_t)winp->pcw_base + winp->pcw_offset;
4454 
4455 	if (win >= PCIC_IOWINDOWS) {
4456 		window->state = 0;
4457 	} else {
4458 		window->state = WS_IO;
4459 	}
4460 	if (winp->pcw_status & PCW_ENABLED)
4461 		window->state |= WS_ENABLED;
4462 
4463 	if (winp->pcw_status & PCS_CARD_16BIT)
4464 		window->state |= WS_16BIT;
4465 #if defined(PCIC_DEBUG)
4466 	if (pcic_debug)
4467 		cmn_err(CE_CONT, "\tsize=%d, speed=%d, base=%p, state=%x\n",
4468 			window->size, (unsigned)window->speed,
4469 			(void *)window->handle, window->state);
4470 #endif
4471 
4472 	return (SUCCESS);
4473 }
4474 
4475 /*
4476  * pcic_ll_reset
4477  *	low level reset
4478  *	separated out so it can be called when already locked
4479  *
4480  *	There are two variables that control the RESET timing:
4481  *		pcic_prereset_time - time in mS before asserting RESET
4482  *		pcic_reset_time - time in mS to assert RESET
4483  *
4484  */
4485 int pcic_prereset_time = 1;
4486 int pcic_reset_time = 10;
4487 int pcic_postreset_time = 20;
4488 int pcic_vpp_is_vcc_during_reset = 0;
4489 
4490 static int
4491 pcic_ll_reset(pcicdev_t *pcic, int socket)
4492 {
4493 	int windowbits, iobits;
4494 	uint32_t pwr;
4495 
4496 	/* save windows that were on */
4497 	windowbits = pcic_getb(pcic, socket, PCIC_MAPPING_ENABLE);
4498 	if (pcic_reset_time == 0)
4499 	    return (windowbits);
4500 	/* turn all windows off */
4501 	pcic_putb(pcic, socket, PCIC_MAPPING_ENABLE, 0);
4502 
4503 #if defined(PCIC_DEBUG)
4504 	pcic_err(pcic->dip, 6,
4505 		"pcic_ll_reset(socket %d) powerlevel=%x cbctl 0x%x cbps 0x%x\n",
4506 		socket, pcic_getb(pcic, socket, PCIC_POWER_CONTROL),
4507 		pcic_getcb(pcic, CB_CONTROL),
4508 		pcic_getcb(pcic, CB_PRESENT_STATE));
4509 #endif
4510 
4511 	if (pcic_vpp_is_vcc_during_reset) {
4512 
4513 	/*
4514 	 * Set VPP to VCC for the duration of the reset - for aironet
4515 	 * card.
4516 	 */
4517 	    if (pcic->pc_flags & PCF_CBPWRCTL) {
4518 		pwr = pcic_getcb(pcic, CB_CONTROL);
4519 		pcic_putcb(pcic, CB_CONTROL, (pwr&~CB_C_VPPMASK)|CB_C_VPPVCC);
4520 		(void) pcic_getcb(pcic, CB_CONTROL);
4521 	    } else {
4522 		pwr = pcic_getb(pcic, socket, PCIC_POWER_CONTROL);
4523 		pcic_putb(pcic, socket, PCIC_POWER_CONTROL,
4524 		    pwr | 1);
4525 		(void) pcic_getb(pcic, socket, PCIC_POWER_CONTROL);
4526 	    }
4527 	}
4528 
4529 	if (pcic_prereset_time > 0) {
4530 		pcic_err(pcic->dip, 8, "pcic_ll_reset pre_wait %d mS\n",
4531 		    pcic_prereset_time);
4532 		pcic_mswait(pcic, socket, pcic_prereset_time);
4533 	}
4534 
4535 	/* turn interrupts off and start a reset */
4536 	pcic_err(pcic->dip, 8,
4537 		"pcic_ll_reset turn interrupts off and start a reset\n");
4538 	iobits = pcic_getb(pcic, socket, PCIC_INTERRUPT);
4539 	iobits &= ~(PCIC_INTR_MASK | PCIC_RESET);
4540 	pcic_putb(pcic, socket, PCIC_INTERRUPT, iobits);
4541 	(void) pcic_getb(pcic, socket, PCIC_INTERRUPT);
4542 
4543 	switch (pcic->pc_type) {
4544 	    case PCIC_INTEL_i82092:
4545 		pcic_82092_smiirq_ctl(pcic, socket, PCIC_82092_CTL_IRQ,
4546 						PCIC_82092_INT_DISABLE);
4547 		break;
4548 	    default:
4549 		break;
4550 	} /* switch */
4551 
4552 	pcic->pc_sockets[socket].pcs_state = 0;
4553 
4554 	if (pcic_reset_time > 0) {
4555 		pcic_err(pcic->dip, 8, "pcic_ll_reset reset_wait %d mS\n",
4556 		    pcic_reset_time);
4557 		pcic_mswait(pcic, socket, pcic_reset_time);
4558 	}
4559 
4560 	pcic_err(pcic->dip, 8, "pcic_ll_reset take it out of reset now\n");
4561 
4562 	/* take it out of RESET now */
4563 	pcic_putb(pcic, socket, PCIC_INTERRUPT, PCIC_RESET | iobits);
4564 	(void) pcic_getb(pcic, socket, PCIC_INTERRUPT);
4565 
4566 	/*
4567 	 * can't access the card for 20ms, but we really don't
4568 	 * want to sit around that long. The pcic is still usable.
4569 	 * memory accesses must wait for RDY to come up.
4570 	 */
4571 	if (pcic_postreset_time > 0) {
4572 		pcic_err(pcic->dip, 8, "pcic_ll_reset post_wait %d mS\n",
4573 		    pcic_postreset_time);
4574 		pcic_mswait(pcic, socket, pcic_postreset_time);
4575 	}
4576 
4577 	if (pcic_vpp_is_vcc_during_reset > 1) {
4578 
4579 	/*
4580 	 * Return VPP power to whatever it was before.
4581 	 */
4582 	    if (pcic->pc_flags & PCF_CBPWRCTL) {
4583 		pcic_putcb(pcic, CB_CONTROL, pwr);
4584 		(void) pcic_getcb(pcic, CB_CONTROL);
4585 	    } else {
4586 		pcic_putb(pcic, socket, PCIC_POWER_CONTROL, pwr);
4587 		(void) pcic_getb(pcic, socket, PCIC_POWER_CONTROL);
4588 	    }
4589 	}
4590 
4591 	pcic_err(pcic->dip, 7, "pcic_ll_reset returning 0x%x\n", windowbits);
4592 
4593 	return (windowbits);
4594 }
4595 
4596 /*
4597  * pcic_reset_socket()
4598  *	SocketServices ResetSocket function
4599  *	puts the PC Card in the socket into the RESET state
4600  *	and then takes it out after the the cycle time
4601  *	The socket is back to initial state when done
4602  */
4603 static int
4604 pcic_reset_socket(dev_info_t *dip, int socket, int mode)
4605 {
4606 	anp_t *anp = ddi_get_driver_private(dip);
4607 	pcicdev_t *pcic = anp->an_private;
4608 	int value;
4609 	int i, mint;
4610 	pcic_socket_t *sockp;
4611 
4612 #if defined(PCIC_DEBUG)
4613 	if (pcic_debug >= 8)
4614 		cmn_err(CE_CONT, "pcic_reset_socket(%p, %d, %d/%s)\n",
4615 		    (void *)dip, socket, mode,
4616 			mode == RESET_MODE_FULL ? "full" : "partial");
4617 #endif
4618 
4619 	mutex_enter(&pcic->pc_lock); /* protect the registers */
4620 
4621 	/* Turn off management interupts. */
4622 	mint = pcic_getb(pcic, socket, PCIC_MANAGEMENT_INT);
4623 	pcic_putb(pcic, socket, PCIC_MANAGEMENT_INT, mint & ~PCIC_CHANGE_MASK);
4624 
4625 	sockp = &pcic->pc_sockets[socket];
4626 
4627 	value = pcic_ll_reset(pcic, socket);
4628 	if (mode == RESET_MODE_FULL) {
4629 		/* disable and unmap all mapped windows */
4630 		for (i = 0; i < PCIC_NUMWINSOCK; i++) {
4631 			if (i < PCIC_IOWINDOWS) {
4632 				if (sockp->pcs_windows[i].io.pcw_status &
4633 				    PCW_MAPPED) {
4634 					pcs_iowin_t *io;
4635 					io = &sockp->pcs_windows[i].io;
4636 					io->pcw_status &= ~PCW_ENABLED;
4637 				}
4638 			} else {
4639 				if (sockp->pcs_windows[i].mem.pcw_status &
4640 				    PCW_MAPPED) {
4641 					pcs_memwin_t *mem;
4642 					mem = &sockp->pcs_windows[i].mem;
4643 					mem->pcw_status &= ~PCW_ENABLED;
4644 				}
4645 			}
4646 		}
4647 	} else {
4648 				/* turn windows back on */
4649 		pcic_putb(pcic, socket, PCIC_MAPPING_ENABLE, value);
4650 		/* wait the rest of the time here */
4651 		pcic_mswait(pcic, socket, 10);
4652 	}
4653 	pcic_putb(pcic, socket, PCIC_MANAGEMENT_INT, mint);
4654 	mutex_exit(&pcic->pc_lock);
4655 	return (SUCCESS);
4656 }
4657 
4658 /*
4659  * pcic_set_interrupt()
4660  *	SocketServices SetInterrupt function
4661  */
4662 static int
4663 pcic_set_interrupt(dev_info_t *dip, set_irq_handler_t *handler)
4664 {
4665 	anp_t *anp = ddi_get_driver_private(dip);
4666 	pcicdev_t *pcic = anp->an_private;
4667 	int value = DDI_SUCCESS;
4668 	inthandler_t *intr;
4669 
4670 #if defined(PCIC_DEBUG)
4671 	if (pcic_debug) {
4672 		cmn_err(CE_CONT,
4673 			"pcic_set_interrupt: entered pc_intr_mode=0x%x\n",
4674 			pcic->pc_intr_mode);
4675 		cmn_err(CE_CONT,
4676 			"\t irq_top=%p handler=%p handler_id=%x\n",
4677 			(void *)pcic->irq_top, (void *)handler->handler,
4678 			handler->handler_id);
4679 	}
4680 #endif
4681 
4682 	/*
4683 	 * If we're on a PCI bus, we route all IO IRQs through a single
4684 	 *	PCI interrupt (typically INT A#) so we don't have to do
4685 	 *	much other than add the caller to general interrupt handler
4686 	 *	and set some state.
4687 	 */
4688 
4689 	intr = kmem_zalloc(sizeof (inthandler_t), KM_NOSLEEP);
4690 	if (intr == NULL)
4691 		return (NO_RESOURCE);
4692 
4693 	switch (pcic->pc_intr_mode) {
4694 	case PCIC_INTR_MODE_PCI_1:
4695 		/*
4696 		 * We only allow above-lock-level IO IRQ handlers
4697 		 *	in the PCI bus case.
4698 		 */
4699 
4700 		mutex_enter(&pcic->intr_lock);
4701 
4702 		if (pcic->irq_top == NULL) {
4703 		    pcic->irq_top = intr;
4704 		    pcic->irq_current = pcic->irq_top;
4705 		} else {
4706 		    while (pcic->irq_current->next != NULL)
4707 			pcic->irq_current = pcic->irq_current->next;
4708 		    pcic->irq_current->next = intr;
4709 		    pcic->irq_current = pcic->irq_current->next;
4710 		}
4711 
4712 		pcic->irq_current->intr =
4713 		    (ddi_intr_handler_t *)handler->handler;
4714 		pcic->irq_current->handler_id = handler->handler_id;
4715 		pcic->irq_current->arg1 = handler->arg1;
4716 		pcic->irq_current->arg2 = handler->arg2;
4717 		pcic->irq_current->socket = handler->socket;
4718 
4719 		mutex_exit(&pcic->intr_lock);
4720 
4721 		handler->iblk_cookie = &pcic->pc_pri;
4722 		handler->idev_cookie = &pcic->pc_dcookie;
4723 		break;
4724 
4725 	default:
4726 		intr->intr = (ddi_intr_handler_t *)handler->handler;
4727 		intr->handler_id = handler->handler_id;
4728 		intr->arg1 = handler->arg1;
4729 		intr->arg2 = handler->arg2;
4730 		intr->socket = handler->socket;
4731 		intr->irq = handler->irq;
4732 
4733 		/*
4734 		 * need to revisit this to see if interrupts can be
4735 		 * shared someday. Note that IRQ is set in the common
4736 		 * code.
4737 		 */
4738 		mutex_enter(&pcic->pc_lock);
4739 		if (pcic->pc_handlers == NULL) {
4740 			pcic->pc_handlers = intr;
4741 			intr->next = intr->prev = intr;
4742 		} else {
4743 			insque(intr, pcic->pc_handlers);
4744 		}
4745 		mutex_exit(&pcic->pc_lock);
4746 
4747 		break;
4748 	}
4749 
4750 	/*
4751 	 * need to fill in cookies in event of multiple high priority
4752 	 * interrupt handlers on same IRQ
4753 	 */
4754 
4755 #if defined(PCIC_DEBUG)
4756 	if (pcic_debug) {
4757 		cmn_err(CE_CONT,
4758 			"pcic_set_interrupt: exit irq_top=%p value=%d\n",
4759 			(void *)pcic->irq_top, value);
4760 	}
4761 #endif
4762 
4763 	if (value == DDI_SUCCESS) {
4764 		return (SUCCESS);
4765 	} else {
4766 		return (BAD_IRQ);
4767 	}
4768 }
4769 
4770 /*
4771  * pcic_clear_interrupt()
4772  *	SocketServices ClearInterrupt function
4773  *
4774  *	Interrupts for PCIC are complicated by the fact that we must
4775  *	follow several different models for interrupts.
4776  *	ISA: there is an interrupt per adapter and per socket and
4777  *		they can't be shared.
4778  *	PCI: some adapters have one PCI interrupt available while others
4779  *		have up to 4.  Solaris may or may not allow us to use more
4780  *		than 1 so we essentially share them all at this point.
4781  *	Hybrid: PCI bridge but interrupts wired to host interrupt controller.
4782  *		This is like ISA but we have to fudge and create an intrspec
4783  *		that PCI's parent understands and bypass the PCI nexus.
4784  *	multifunction: this requires sharing the interrupts on a per-socket
4785  *		basis.
4786  */
4787 static int
4788 pcic_clear_interrupt(dev_info_t *dip, clear_irq_handler_t *handler)
4789 {
4790 	anp_t *anp = ddi_get_driver_private(dip);
4791 	pcicdev_t *pcic = anp->an_private;
4792 	inthandler_t *intr, *prev, *current;
4793 	int i;
4794 
4795 	/*
4796 	 * If we're on a PCI bus, we route all IO IRQs through a single
4797 	 *	PCI interrupt (typically INT A#) so we don't have to do
4798 	 *	much other than remove the caller from the general
4799 	 *	interrupt handler callout list.
4800 	 */
4801 
4802 #if defined(PCIC_DEBUG)
4803 	if (pcic_debug) {
4804 		cmn_err(CE_CONT,
4805 			"pcic_clear_interrupt: entered pc_intr_mode=0x%x\n",
4806 			pcic->pc_intr_mode);
4807 		cmn_err(CE_CONT,
4808 			"\t irq_top=%p handler=%p handler_id=%x\n",
4809 			(void *)pcic->irq_top, (void *)handler->handler,
4810 			handler->handler_id);
4811 	}
4812 #endif
4813 
4814 	switch (pcic->pc_intr_mode) {
4815 	case PCIC_INTR_MODE_PCI_1:
4816 
4817 		mutex_enter(&pcic->intr_lock);
4818 		if (pcic->irq_top == NULL) {
4819 			mutex_exit(&pcic->intr_lock);
4820 			return (BAD_IRQ);
4821 		}
4822 
4823 		intr = NULL;
4824 		pcic->irq_current = pcic->irq_top;
4825 
4826 		while ((pcic->irq_current != NULL) &&
4827 				(pcic->irq_current->handler_id !=
4828 						handler->handler_id)) {
4829 			intr = pcic->irq_current;
4830 			pcic->irq_current = pcic->irq_current->next;
4831 		}
4832 
4833 		if (pcic->irq_current == NULL) {
4834 			mutex_exit(&pcic->intr_lock);
4835 			return (BAD_IRQ);
4836 		}
4837 
4838 		if (intr != NULL) {
4839 			intr->next = pcic->irq_current->next;
4840 		} else {
4841 			pcic->irq_top = pcic->irq_current->next;
4842 		}
4843 
4844 		current = pcic->irq_current;
4845 		pcic->irq_current = pcic->irq_top;
4846 		mutex_exit(&pcic->intr_lock);
4847 		kmem_free(current, sizeof (inthandler_t));
4848 
4849 		break;
4850 
4851 	default:
4852 
4853 		mutex_enter(&pcic->pc_lock);
4854 		intr = pcic_handlers;
4855 		prev = (inthandler_t *)&pcic_handlers;
4856 
4857 		while (intr != NULL) {
4858 		    if (intr->handler_id == handler->handler_id) {
4859 			i = intr->irq & PCIC_INTR_MASK;
4860 			if (--pcic_irq_map[i].count == 0) {
4861 				/* multi-handler form */
4862 				(void) ddi_intr_disable(pcic->pc_intr_htblp[i]);
4863 				(void) ddi_intr_remove_handler(
4864 				    pcic->pc_intr_htblp[i]);
4865 				(void) ddi_intr_free(pcic->pc_intr_htblp[i]);
4866 				(void) pcmcia_return_intr(pcic->dip, i);
4867 #if defined(PCIC_DEBUG)
4868 				if (pcic_debug) {
4869 					cmn_err(CE_CONT,
4870 						"removing interrupt %d at %s "
4871 						"priority\n", i, "high");
4872 					cmn_err(CE_CONT,
4873 						"ddi_remove_intr(%p, %x, %p)\n",
4874 						(void *)dip,
4875 						0,
4876 						(void *)intr->iblk_cookie);
4877 				}
4878 #endif
4879 			}
4880 			prev->next = intr->next;
4881 			kmem_free(intr, sizeof (inthandler_t));
4882 			intr = prev->next;
4883 		    } else {
4884 			prev = intr;
4885 			intr = intr->next;
4886 		    } /* if (handler_id) */
4887 		} /* while */
4888 
4889 		mutex_exit(&pcic->pc_lock);
4890 	}
4891 
4892 #if defined(PCIC_DEBUG)
4893 	if (pcic_debug) {
4894 		cmn_err(CE_CONT,
4895 		"pcic_clear_interrupt: exit irq_top=%p\n",
4896 		(void *)pcic->irq_top);
4897 	}
4898 #endif
4899 
4900 
4901 	return (SUCCESS);
4902 }
4903 
4904 struct intel_regs {
4905 	char *name;
4906 	int   off;
4907 	char *fmt;
4908 } iregs[] = {
4909 	{"ident     ", 0},
4910 	{"if-status ", 1, "\020\1BVD1\2BVD2\3CD1\4CD2\5WP\6RDY\7PWR\10~GPI"},
4911 	{"power     ", 2, "\020\1Vpp1c0\2Vpp1c1\3Vpp2c0\4Vpp2c1\5PE\6AUTO"
4912 		"\7DRD\10OE"},
4913 	{"cardstatus", 4, "\020\1BD\2BW\3RC\4CD\5GPI\6R1\7R2\010R3"},
4914 	{"enable    ", 6, "\020\1MW0\2MW1\3MW2\4MW3\5MW4\6MEM16\7IO0\10IO1"},
4915 	{"cd-gcr    ", 0x16, "\020\1MDI16\2CRE\3GPIE\4GPIT\5CDR\6S/W"},
4916 	{"GCR       ", 0x1e, "\020\1PD\2LEVEL\3WCSC\4PLS14"},
4917 	{"int-gcr   ", 3, "\020\5INTR\6IO\7~RST\10RI"},
4918 	{"management", 5, "\020\1BDE\2BWE\3RE\4CDE"},
4919 	{"volt-sense", 0x1f, "\020\1A_VS1\2A_VS2\3B_VS1\4B_VS2"},
4920 	{"volt-sel  ", 0x2f, "\020\5EXTCONF\6BUSSELECT\7MIXEDV\10ISAV"},
4921 	{"VG ext A  ", 0x3c, "\20\3IVS\4CABLE\5CSTEP\6TEST\7RIO"},
4922 	{"io-ctrl   ", 7, "\020\1DS0\2IOCS0\3ZWS0\4WS0\5DS1\6IOS1\7ZWS1\10WS1"},
4923 	{"io0-slow  ", 8},
4924 	{"io0-shi   ", 9},
4925 	{"io0-elow  ", 0xa},
4926 	{"io0-ehi   ", 0xb},
4927 	{"io1-slow  ", 0xc},
4928 	{"io1-shi   ", 0xd},
4929 	{"io1-elow  ", 0xe},
4930 	{"io1-ehi   ", 0xf},
4931 	{"mem0-slow ", 0x10},
4932 	{"mem0-shi  ", 0x11, "\020\7ZW\10DS"},
4933 	{"mem0-elow ", 0x12},
4934 	{"mem0-ehi  ", 0x13, "\020\7WS0\10WS1"},
4935 	{"card0-low ", 0x14},
4936 	{"card0-hi  ", 0x15, "\020\7AM\10WP"},
4937 	{"mem1-slow ", 0x18},
4938 	{"mem1-shi  ", 0x19, "\020\7ZW\10DS"},
4939 	{"mem1-elow ", 0x1a},
4940 	{"mem1-ehi  ", 0x1b, "\020\7WS0\10WS1"},
4941 	{"card1-low ", 0x1c},
4942 	{"card1-hi  ", 0x1d, "\020\7AM\10WP"},
4943 	{"mem2-slow ", 0x20},
4944 	{"mem2-shi  ", 0x21, "\020\7ZW\10DS"},
4945 	{"mem2-elow ", 0x22},
4946 	{"mem2-ehi  ", 0x23, "\020\7WS0\10WS1"},
4947 	{"card2-low ", 0x24},
4948 	{"card2-hi  ", 0x25, "\020\7AM\10WP"},
4949 	{"mem3-slow ", 0x28},
4950 	{"mem3-shi  ", 0x29, "\020\7ZW\10DS"},
4951 	{"mem3-elow ", 0x2a},
4952 	{"mem3-ehi  ", 0x2b, "\020\7WS0\10WS1"},
4953 	{"card3-low ", 0x2c},
4954 	{"card3-hi  ", 0x2d, "\020\7AM\10WP"},
4955 
4956 	{"mem4-slow ", 0x30},
4957 	{"mem4-shi  ", 0x31, "\020\7ZW\10DS"},
4958 	{"mem4-elow ", 0x32},
4959 	{"mem4-ehi  ", 0x33, "\020\7WS0\10WS1"},
4960 	{"card4-low ", 0x34},
4961 	{"card4-hi  ", 0x35, "\020\7AM\10WP"},
4962 	{"mpage0    ", 0x40},
4963 	{"mpage1    ", 0x41},
4964 	{"mpage2    ", 0x42},
4965 	{"mpage3    ", 0x43},
4966 	{"mpage4    ", 0x44},
4967 	{NULL},
4968 };
4969 
4970 static struct intel_regs cregs[] = {
4971 	{"misc-ctl1 ", 0x16, "\20\2VCC3\3PMI\4PSI\5SPKR\10INPACK"},
4972 	{"fifo      ", 0x17, "\20\6DIOP\7DMEMP\10EMPTY"},
4973 	{"misc-ctl2 ", 0x1e, "\20\1XCLK\2LOW\3SUSP\4CORE5V\5TCD\10RIOUT"},
4974 	{"chip-info ", 0x1f, "\20\6DUAL"},
4975 	{"IO-offlow0", 0x36},
4976 	{"IO-offhi0 ", 0x37},
4977 	{"IO-offlow1", 0x38},
4978 	{"IO-offhi1 ", 0x39},
4979 	NULL,
4980 };
4981 
4982 static struct intel_regs cxregs[] = {
4983 	{"ext-ctl-1 ", 0x03,
4984 		"\20\1VCCLCK\2AUTOCLR\3LED\4INVIRQC\5INVIRQM\6PUC"},
4985 	{"misc-ctl3 ", 0x25, "\20\5HWSUSP"},
4986 	{"mem0-up   ", 0x05},
4987 	{"mem1-up   ", 0x06},
4988 	{"mem2-up   ", 0x07},
4989 	{"mem3-up   ", 0x08},
4990 	{"mem4-up   ", 0x09},
4991 	{NULL}
4992 };
4993 
4994 void
4995 xxdmp_cl_regs(pcicdev_t *pcic, int socket, uint32_t len)
4996 {
4997 	int i, value, j;
4998 	char buff[256];
4999 	char *fmt;
5000 
5001 	cmn_err(CE_CONT, "--------- Cirrus Logic Registers --------\n");
5002 	for (buff[0] = '\0', i = 0; cregs[i].name != NULL && len-- != 0; i++) {
5003 		int sval;
5004 		if (cregs[i].off == PCIC_MISC_CTL_2)
5005 			sval = 0;
5006 		else
5007 			sval = socket;
5008 		value = pcic_getb(pcic, sval, cregs[i].off);
5009 		if (i & 1) {
5010 			if (cregs[i].fmt)
5011 				fmt = "%s\t%s\t%b\n";
5012 			else
5013 				fmt = "%s\t%s\t%x\n";
5014 			cmn_err(CE_CONT, fmt, buff,
5015 				cregs[i].name, value, cregs[i].fmt);
5016 			buff[0] = '\0';
5017 		} else {
5018 			if (cregs[i].fmt)
5019 				fmt = "\t%s\t%b";
5020 			else
5021 				fmt = "\t%s\t%x";
5022 			(void) sprintf(buff, fmt,
5023 				cregs[i].name, value, cregs[i].fmt);
5024 			for (j = strlen(buff); j < 40; j++)
5025 				buff[j] = ' ';
5026 			buff[40] = '\0';
5027 		}
5028 	}
5029 	cmn_err(CE_CONT, "%s\n", buff);
5030 
5031 	i = pcic_getb(pcic, socket, PCIC_TIME_SETUP_0);
5032 	j = pcic_getb(pcic, socket, PCIC_TIME_SETUP_1);
5033 	cmn_err(CE_CONT, "\tsetup-tim0\t%x\tsetup-tim1\t%x\n", i, j);
5034 
5035 	i = pcic_getb(pcic, socket, PCIC_TIME_COMMAND_0);
5036 	j = pcic_getb(pcic, socket, PCIC_TIME_COMMAND_1);
5037 	cmn_err(CE_CONT, "\tcmd-tim0  \t%x\tcmd-tim1  \t%x\n", i, j);
5038 
5039 	i = pcic_getb(pcic, socket, PCIC_TIME_RECOVER_0);
5040 	j = pcic_getb(pcic, socket, PCIC_TIME_RECOVER_1);
5041 	cmn_err(CE_CONT, "\trcvr-tim0 \t%x\trcvr-tim1 \t%x\n", i, j);
5042 
5043 	cmn_err(CE_CONT, "--------- Extended Registers  --------\n");
5044 
5045 	for (buff[0] = '\0', i = 0; cxregs[i].name != NULL && len-- != 0; i++) {
5046 		value = clext_reg_read(pcic, socket, cxregs[i].off);
5047 		if (i & 1) {
5048 			if (cxregs[i].fmt)
5049 				fmt = "%s\t%s\t%b\n";
5050 			else
5051 				fmt = "%s\t%s\t%x\n";
5052 			cmn_err(CE_CONT, fmt, buff,
5053 				cxregs[i].name, value, cxregs[i].fmt);
5054 			buff[0] = '\0';
5055 		} else {
5056 			if (cxregs[i].fmt)
5057 				fmt = "\t%s\t%b";
5058 			else
5059 				fmt = "\t%s\t%x";
5060 			(void) sprintf(buff, fmt,
5061 				cxregs[i].name, value, cxregs[i].fmt);
5062 			for (j = strlen(buff); j < 40; j++)
5063 				buff[j] = ' ';
5064 			buff[40] = '\0';
5065 		}
5066 	}
5067 }
5068 
5069 #if defined(PCIC_DEBUG)
5070 static void
5071 xxdmp_all_regs(pcicdev_t *pcic, int socket, uint32_t len)
5072 {
5073 	int i, value, j;
5074 	char buff[256];
5075 	char *fmt;
5076 
5077 #if defined(PCIC_DEBUG)
5078 	if (pcic_debug < 2)
5079 		return;
5080 #endif
5081 	cmn_err(CE_CONT,
5082 		"----------- PCIC Registers for socket %d---------\n",
5083 		socket);
5084 	cmn_err(CE_CONT,
5085 		"\tname       value                        name       value\n");
5086 
5087 	for (buff[0] = '\0', i = 0; iregs[i].name != NULL && len-- != 0; i++) {
5088 		value = pcic_getb(pcic, socket, iregs[i].off);
5089 		if (i & 1) {
5090 			if (iregs[i].fmt)
5091 				fmt = "%s\t%s\t%b\n";
5092 			else
5093 				fmt = "%s\t%s\t%x\n";
5094 			cmn_err(CE_CONT, fmt, buff,
5095 				iregs[i].name, value, iregs[i].fmt);
5096 			buff[0] = '\0';
5097 		} else {
5098 			if (iregs[i].fmt)
5099 				fmt = "\t%s\t%b";
5100 			else
5101 				fmt = "\t%s\t%x";
5102 			(void) sprintf(buff, fmt,
5103 				iregs[i].name, value, iregs[i].fmt);
5104 			for (j = strlen(buff); j < 40; j++)
5105 				buff[j] = ' ';
5106 			buff[40] = '\0';
5107 		}
5108 	}
5109 	switch (pcic->pc_type) {
5110 	case PCIC_CL_PD6710:
5111 	case PCIC_CL_PD6722:
5112 	case PCIC_CL_PD6729:
5113 	case PCIC_CL_PD6832:
5114 		(void) xxdmp_cl_regs(pcic, socket, 0xFFFF);
5115 		break;
5116 	}
5117 	cmn_err(CE_CONT, "%s\n", buff);
5118 }
5119 #endif
5120 
5121 /*
5122  * pcic_mswait(ms)
5123  *	sleep ms milliseconds
5124  *	call drv_usecwait once for each ms
5125  */
5126 static void
5127 pcic_mswait(pcicdev_t *pcic, int socket, int ms)
5128 {
5129 	if (ms) {
5130 		pcic->pc_sockets[socket].pcs_flags |= PCS_WAITING;
5131 		pcic_mutex_exit(&pcic->pc_lock);
5132 		delay(drv_usectohz(ms*1000));
5133 		pcic_mutex_enter(&pcic->pc_lock);
5134 		pcic->pc_sockets[socket].pcs_flags &= ~PCS_WAITING;
5135 	}
5136 }
5137 
5138 /*
5139  * pcic_check_ready(pcic, index, off)
5140  *      Wait for card to come ready
5141  *      We only wait if the card is NOT in RESET
5142  *      and power is on.
5143  */
5144 static boolean_t
5145 pcic_check_ready(pcicdev_t *pcic, int socket)
5146 {
5147 	int ifstate, intstate;
5148 
5149 	intstate = pcic_getb(pcic, socket, PCIC_INTERRUPT);
5150 	ifstate = pcic_getb(pcic, socket, PCIC_INTERFACE_STATUS);
5151 
5152 	if ((intstate & PCIC_RESET) &&
5153 	    ((ifstate & (PCIC_READY|PCIC_POWER_ON|PCIC_ISTAT_CD_MASK)) ==
5154 	    (PCIC_READY|PCIC_POWER_ON|PCIC_CD_PRESENT_OK)))
5155 		return (B_TRUE);
5156 
5157 #ifdef  PCIC_DEBUG
5158 	pcic_err(NULL, 5, "pcic_check_read: Card not ready, intstate = 0x%x, "
5159 	    "ifstate = 0x%x\n", intstate, ifstate);
5160 	if (pcic_debug) {
5161 		pcic_debug += 4;
5162 		xxdmp_all_regs(pcic, socket, -1);
5163 		pcic_debug -= 4;
5164 	}
5165 #endif
5166 	return (B_FALSE);
5167 }
5168 
5169 /*
5170  * Cirrus Logic extended register read/write routines
5171  */
5172 static int
5173 clext_reg_read(pcicdev_t *pcic, int sn, uchar_t ext_reg)
5174 {
5175 	int val;
5176 
5177 	switch (pcic->pc_io_type) {
5178 	case PCIC_IO_TYPE_YENTA:
5179 		val = ddi_get8(pcic->handle,
5180 		    pcic->ioaddr + CB_CLEXT_OFFSET + ext_reg);
5181 		break;
5182 	default:
5183 		pcic_putb(pcic, sn, PCIC_CL_EXINDEX, ext_reg);
5184 		val = pcic_getb(pcic, sn, PCIC_CL_EXINDEX + 1);
5185 		break;
5186 	}
5187 
5188 	return (val);
5189 }
5190 
5191 static void
5192 clext_reg_write(pcicdev_t *pcic, int sn, uchar_t ext_reg, uchar_t value)
5193 {
5194 	switch (pcic->pc_io_type) {
5195 	case PCIC_IO_TYPE_YENTA:
5196 		ddi_put8(pcic->handle,
5197 		    pcic->ioaddr + CB_CLEXT_OFFSET + ext_reg, value);
5198 		break;
5199 	default:
5200 		pcic_putb(pcic, sn, PCIC_CL_EXINDEX, ext_reg);
5201 		pcic_putb(pcic, sn, PCIC_CL_EXINDEX + 1, value);
5202 		break;
5203 	}
5204 }
5205 
5206 /*
5207  * Misc PCI functions
5208  */
5209 static void
5210 pcic_iomem_pci_ctl(ddi_acc_handle_t handle, uchar_t *cfgaddr, unsigned flags)
5211 {
5212 	unsigned cmd;
5213 
5214 	if (flags & (PCIC_ENABLE_IO | PCIC_ENABLE_MEM)) {
5215 		cmd = ddi_get16(handle, (ushort_t *)(cfgaddr + 4));
5216 		if ((cmd & (PCI_COMM_IO|PCI_COMM_MAE)) ==
5217 		    (PCI_COMM_IO|PCI_COMM_MAE))
5218 			return;
5219 
5220 		if (flags & PCIC_ENABLE_IO)
5221 		    cmd |= PCI_COMM_IO;
5222 
5223 		if (flags & PCIC_ENABLE_MEM)
5224 		    cmd |= PCI_COMM_MAE;
5225 
5226 		ddi_put16(handle, (ushort_t *)(cfgaddr + 4), cmd);
5227 	} /* if (PCIC_ENABLE_IO | PCIC_ENABLE_MEM) */
5228 }
5229 
5230 /*
5231  * pcic_find_pci_type - Find and return PCI-PCMCIA adapter type
5232  */
5233 static int
5234 pcic_find_pci_type(pcicdev_t *pcic)
5235 {
5236 	uint32_t vend, device;
5237 
5238 	vend = ddi_getprop(DDI_DEV_T_ANY, pcic->dip,
5239 				DDI_PROP_CANSLEEP|DDI_PROP_DONTPASS,
5240 				"vendor-id", -1);
5241 	device = ddi_getprop(DDI_DEV_T_ANY, pcic->dip,
5242 				DDI_PROP_CANSLEEP|DDI_PROP_DONTPASS,
5243 				"device-id", -1);
5244 
5245 	device = PCI_ID(vend, device);
5246 	pcic->pc_type = device;
5247 	pcic->pc_chipname = "PCI:unknown";
5248 
5249 	switch (device) {
5250 	case PCIC_INTEL_i82092:
5251 		pcic->pc_chipname = PCIC_TYPE_i82092;
5252 		break;
5253 	case PCIC_CL_PD6729:
5254 		pcic->pc_chipname = PCIC_TYPE_PD6729;
5255 		/*
5256 		 * Some 6730's incorrectly identify themselves
5257 		 *	as a 6729, so we need to do some more tests
5258 		 *	here to see if the device that's claiming
5259 		 *	to be a 6729 is really a 6730.
5260 		 */
5261 		if ((clext_reg_read(pcic, 0, PCIC_CLEXT_MISC_CTL_3) &
5262 			PCIC_CLEXT_MISC_CTL_3_REV_MASK) ==
5263 				0) {
5264 			pcic->pc_chipname = PCIC_TYPE_PD6730;
5265 			pcic->pc_type = PCIC_CL_PD6730;
5266 		}
5267 		break;
5268 	case PCIC_CL_PD6730:
5269 		pcic->pc_chipname = PCIC_TYPE_PD6730;
5270 		break;
5271 	case PCIC_CL_PD6832:
5272 		pcic->pc_chipname = PCIC_TYPE_PD6832;
5273 		break;
5274 	case PCIC_SMC_34C90:
5275 		pcic->pc_chipname = PCIC_TYPE_34C90;
5276 		break;
5277 	case PCIC_TOSHIBA_TOPIC95:
5278 		pcic->pc_chipname = PCIC_TYPE_TOPIC95;
5279 		break;
5280 	case PCIC_TOSHIBA_TOPIC100:
5281 		pcic->pc_chipname = PCIC_TYPE_TOPIC100;
5282 		break;
5283 	case PCIC_TI_PCI1031:
5284 		pcic->pc_chipname = PCIC_TYPE_PCI1031;
5285 		break;
5286 	case PCIC_TI_PCI1130:
5287 		pcic->pc_chipname = PCIC_TYPE_PCI1130;
5288 		break;
5289 	case PCIC_TI_PCI1131:
5290 		pcic->pc_chipname = PCIC_TYPE_PCI1131;
5291 		break;
5292 	case PCIC_TI_PCI1250:
5293 		pcic->pc_chipname = PCIC_TYPE_PCI1250;
5294 		break;
5295 	case PCIC_TI_PCI1225:
5296 		pcic->pc_chipname = PCIC_TYPE_PCI1225;
5297 		break;
5298 	case PCIC_TI_PCI1410:
5299 		pcic->pc_chipname = PCIC_TYPE_PCI1410;
5300 		break;
5301 	case PCIC_TI_PCI1510:
5302 		pcic->pc_chipname = PCIC_TYPE_PCI1510;
5303 		break;
5304 	case PCIC_TI_PCI1520:
5305 		pcic->pc_chipname = PCIC_TYPE_PCI1520;
5306 		break;
5307 	case PCIC_TI_PCI1221:
5308 		pcic->pc_chipname = PCIC_TYPE_PCI1221;
5309 		break;
5310 	case PCIC_TI_PCI1050:
5311 		pcic->pc_chipname = PCIC_TYPE_PCI1050;
5312 		break;
5313 	case PCIC_ENE_1410:
5314 		pcic->pc_chipname = PCIC_TYPE_1410;
5315 		break;
5316 	case PCIC_O2_OZ6912:
5317 		pcic->pc_chipname = PCIC_TYPE_OZ6912;
5318 		break;
5319 	case PCIC_RICOH_RL5C466:
5320 		pcic->pc_chipname = PCIC_TYPE_RL5C466;
5321 		break;
5322 	case PCIC_TI_PCI1420:
5323 		pcic->pc_chipname = PCIC_TYPE_PCI1420;
5324 		break;
5325 	case PCIC_ENE_1420:
5326 		pcic->pc_chipname = PCIC_TYPE_1420;
5327 		break;
5328 	default:
5329 		switch (PCI_ID(vend, (uint32_t)0)) {
5330 		case PCIC_TOSHIBA_VENDOR:
5331 			pcic->pc_chipname = PCIC_TYPE_TOSHIBA;
5332 			pcic->pc_type = PCIC_TOSHIBA_VENDOR;
5333 			break;
5334 		case PCIC_TI_VENDOR:
5335 			pcic->pc_chipname = PCIC_TYPE_TI;
5336 			pcic->pc_type = PCIC_TI_VENDOR;
5337 			break;
5338 		case PCIC_O2MICRO_VENDOR:
5339 			pcic->pc_chipname = PCIC_TYPE_O2MICRO;
5340 			pcic->pc_type = PCIC_O2MICRO_VENDOR;
5341 			break;
5342 		case PCIC_RICOH_VENDOR:
5343 			pcic->pc_chipname = PCIC_TYPE_RICOH;
5344 			pcic->pc_type = PCIC_RICOH_VENDOR;
5345 			break;
5346 		default:
5347 			if (!(pcic->pc_flags & PCF_CARDBUS))
5348 				return (DDI_FAILURE);
5349 			pcic->pc_chipname = PCIC_TYPE_YENTA;
5350 			break;
5351 		}
5352 	}
5353 	return (DDI_SUCCESS);
5354 }
5355 
5356 static void
5357 pcic_82092_smiirq_ctl(pcicdev_t *pcic, int socket, int intr, int state)
5358 {
5359 	uchar_t ppirr = ddi_get8(pcic->cfg_handle,
5360 					pcic->cfgaddr + PCIC_82092_PPIRR);
5361 	uchar_t val;
5362 
5363 	if (intr == PCIC_82092_CTL_SMI) {
5364 		val = PCIC_82092_SMI_CTL(socket,
5365 						PCIC_82092_INT_DISABLE);
5366 		ppirr &= ~val;
5367 		val = PCIC_82092_SMI_CTL(socket, state);
5368 		ppirr |= val;
5369 	} else {
5370 		val = PCIC_82092_IRQ_CTL(socket,
5371 						PCIC_82092_INT_DISABLE);
5372 		ppirr &= ~val;
5373 		val = PCIC_82092_IRQ_CTL(socket, state);
5374 		ppirr |= val;
5375 	}
5376 	ddi_put8(pcic->cfg_handle, pcic->cfgaddr + PCIC_82092_PPIRR,
5377 			ppirr);
5378 }
5379 
5380 static uint_t
5381 pcic_cd_softint(caddr_t arg1, caddr_t arg2)
5382 {
5383 	pcic_socket_t *sockp = (pcic_socket_t *)arg1;
5384 	uint_t rc = DDI_INTR_UNCLAIMED;
5385 
5386 	_NOTE(ARGUNUSED(arg2))
5387 
5388 	mutex_enter(&sockp->pcs_pcic->pc_lock);
5389 	if (sockp->pcs_cd_softint_flg) {
5390 		uint8_t status;
5391 		sockp->pcs_cd_softint_flg = 0;
5392 		rc = DDI_INTR_CLAIMED;
5393 		status = pcic_getb(sockp->pcs_pcic, sockp->pcs_socket,
5394 			PCIC_INTERFACE_STATUS);
5395 		pcic_handle_cd_change(sockp->pcs_pcic, sockp, status);
5396 	}
5397 	mutex_exit(&sockp->pcs_pcic->pc_lock);
5398 	return (rc);
5399 }
5400 
5401 int pcic_debounce_cnt = PCIC_REM_DEBOUNCE_CNT;
5402 int pcic_debounce_intr_time = PCIC_REM_DEBOUNCE_TIME;
5403 int pcic_debounce_cnt_ok = PCIC_DEBOUNCE_OK_CNT;
5404 
5405 #ifdef CARDBUS
5406 static uint32_t pcic_cbps_on = 0;
5407 static uint32_t pcic_cbps_off = CB_PS_NOTACARD | CB_PS_CCDMASK |
5408 				CB_PS_XVCARD | CB_PS_YVCARD;
5409 #else
5410 static uint32_t pcic_cbps_on = CB_PS_16BITCARD;
5411 static uint32_t pcic_cbps_off = CB_PS_NOTACARD | CB_PS_CCDMASK |
5412 				CB_PS_CBCARD |
5413 				CB_PS_XVCARD | CB_PS_YVCARD;
5414 #endif
5415 static void
5416 pcic_handle_cd_change(pcicdev_t *pcic, pcic_socket_t *sockp, uint8_t status)
5417 {
5418 	boolean_t	do_debounce = B_FALSE;
5419 	int		debounce_time = drv_usectohz(pcic_debounce_time);
5420 	uint8_t		irq;
5421 	timeout_id_t	debounce;
5422 
5423 	/*
5424 	 * Always reset debounce but may need to check original state later.
5425 	 */
5426 	debounce = sockp->pcs_debounce_id;
5427 	sockp->pcs_debounce_id = 0;
5428 
5429 	/*
5430 	 * Check to see whether a card is present or not. There are
5431 	 *	only two states that we are concerned with - the state
5432 	 *	where both CD pins are asserted, which means that the
5433 	 *	card is fully seated, and the state where neither CD
5434 	 *	pin is asserted, which means that the card is not
5435 	 *	present.
5436 	 * The CD signals are generally very noisy and cause a lot of
5437 	 *	contact bounce as the card is being inserted and
5438 	 *	removed, so we need to do some software debouncing.
5439 	 */
5440 
5441 #ifdef PCIC_DEBUG
5442 	    pcic_err(pcic->dip, 6,
5443 		    "pcic%d handle_cd_change: socket %d card status 0x%x"
5444 		    " deb 0x%p\n", ddi_get_instance(pcic->dip),
5445 		    sockp->pcs_socket, status, debounce);
5446 #endif
5447 	switch (status & PCIC_ISTAT_CD_MASK) {
5448 	case PCIC_CD_PRESENT_OK:
5449 	    sockp->pcs_flags &= ~(PCS_CARD_REMOVED|PCS_CARD_CBREM);
5450 	    if (!(sockp->pcs_flags & PCS_CARD_PRESENT)) {
5451 		uint32_t cbps;
5452 #ifdef PCIC_DEBUG
5453 		pcic_err(pcic->dip, 8, "New card (0x%x)\n", sockp->pcs_flags);
5454 #endif
5455 		cbps = pcic_getcb(pcic, CB_PRESENT_STATE);
5456 #ifdef PCIC_DEBUG
5457 		pcic_err(pcic->dip, 8, "CBus PS (0x%x)\n", cbps);
5458 #endif
5459 		/*
5460 		 * Check the CB bits are sane.
5461 		 */
5462 		if ((cbps & pcic_cbps_on) != pcic_cbps_on ||
5463 		    cbps & pcic_cbps_off) {
5464 		    cmn_err(CE_WARN,
5465 			    "%s%d: Odd Cardbus Present State 0x%x\n",
5466 			    ddi_get_name(pcic->dip),
5467 			    ddi_get_instance(pcic->dip),
5468 			    cbps);
5469 		    pcic_putcb(pcic, CB_EVENT_FORCE, CB_EF_CVTEST);
5470 		    debounce = 0;
5471 		    debounce_time = drv_usectohz(1000000);
5472 		}
5473 		if (debounce) {
5474 		    sockp->pcs_flags |= PCS_CARD_PRESENT;
5475 		    if (pcic_do_insertion) {
5476 
5477 			cbps = pcic_getcb(pcic, CB_PRESENT_STATE);
5478 
5479 			if (cbps & CB_PS_16BITCARD) {
5480 			    pcic_err(pcic->dip, 8, "16 bit card inserted\n");
5481 			    sockp->pcs_flags |= PCS_CARD_IS16BIT;
5482 			    /* calls pcm_adapter_callback() */
5483 			    if (pcic->pc_callback) {
5484 
5485 				(void) ddi_prop_update_string(DDI_DEV_T_NONE,
5486 					pcic->dip, PCM_DEVICETYPE,
5487 					"pccard");
5488 				PC_CALLBACK(pcic->dip, pcic->pc_cb_arg,
5489 					    PCE_CARD_INSERT,
5490 					    sockp->pcs_socket);
5491 			    }
5492 			} else if (cbps & CB_PS_CBCARD) {
5493 			    pcic_err(pcic->dip, 8, "32 bit card inserted\n");
5494 
5495 			    if (pcic->pc_flags & PCF_CARDBUS) {
5496 				sockp->pcs_flags |= PCS_CARD_ISCARDBUS;
5497 #ifdef CARDBUS
5498 				if (!pcic_load_cardbus(pcic, sockp)) {
5499 				    pcic_unload_cardbus(pcic, sockp);
5500 				}
5501 
5502 #else
5503 				cmn_err(CE_NOTE,
5504 					"32 bit Cardbus not supported in"
5505 					" this device driver\n");
5506 #endif
5507 			    } else {
5508 				/*
5509 				 * Ignore the card
5510 				 */
5511 				cmn_err(CE_NOTE,
5512 					"32 bit Cardbus not supported on this"
5513 					" device\n");
5514 			    }
5515 			} else {
5516 			    cmn_err(CE_NOTE,
5517 				"Unsupported PCMCIA card inserted\n");
5518 			}
5519 		    }
5520 		    syshw_send_signal(sockp->pcs_syshwsig);
5521 		} else {
5522 		    do_debounce = B_TRUE;
5523 		}
5524 	    } else {
5525 		/*
5526 		 * It is possible to come through here if the system
5527 		 * starts up with cards already inserted. Do nothing
5528 		 * and don't worry about it.
5529 		 */
5530 #ifdef PCIC_DEBUG
5531 		pcic_err(pcic->dip, 5,
5532 			"pcic%d: Odd card insertion indication on socket %d\n",
5533 			ddi_get_instance(pcic->dip),
5534 			sockp->pcs_socket);
5535 #endif
5536 	    }
5537 	    break;
5538 
5539 	default:
5540 	    if (!(sockp->pcs_flags & PCS_CARD_PRESENT)) {
5541 		/*
5542 		 * Someone has started to insert a card so delay a while.
5543 		 */
5544 		do_debounce = B_TRUE;
5545 		break;
5546 	    }
5547 		/*
5548 		 * Otherwise this is basically the same as not present
5549 		 * so fall through.
5550 		 */
5551 
5552 		/* FALLTHRU */
5553 	case 0:
5554 	    if (sockp->pcs_flags & PCS_CARD_PRESENT) {
5555 		if (pcic->pc_flags & PCF_CBPWRCTL) {
5556 		    pcic_putcb(pcic, CB_CONTROL, 0);
5557 		} else {
5558 		    pcic_putb(pcic, sockp->pcs_socket, PCIC_POWER_CONTROL, 0);
5559 		    (void) pcic_getb(pcic, sockp->pcs_socket,
5560 			PCIC_POWER_CONTROL);
5561 		}
5562 #ifdef PCIC_DEBUG
5563 		pcic_err(pcic->dip, 8, "Card removed\n");
5564 #endif
5565 		sockp->pcs_flags &= ~PCS_CARD_PRESENT;
5566 
5567 		if (sockp->pcs_flags & PCS_CARD_IS16BIT) {
5568 		    sockp->pcs_flags &= ~PCS_CARD_IS16BIT;
5569 		    if (pcic_do_removal && pcic->pc_callback) {
5570 			PC_CALLBACK(pcic->dip, pcic->pc_cb_arg,
5571 				    PCE_CARD_REMOVAL, sockp->pcs_socket);
5572 		    }
5573 		}
5574 		if (sockp->pcs_flags & PCS_CARD_ISCARDBUS) {
5575 		    sockp->pcs_flags &= ~PCS_CARD_ISCARDBUS;
5576 		    sockp->pcs_flags |= PCS_CARD_CBREM;
5577 		}
5578 		sockp->pcs_flags |= PCS_CARD_REMOVED;
5579 
5580 		do_debounce = B_TRUE;
5581 	    }
5582 	    if (debounce && (sockp->pcs_flags & PCS_CARD_REMOVED)) {
5583 		if (sockp->pcs_flags & PCS_CARD_CBREM) {
5584 		/*
5585 		 * Ensure that we do the unloading in the
5586 		 * debounce handler, that way we're not doing
5587 		 * nasty things in an interrupt handler. e.g.
5588 		 * a USB device will wait for data which will
5589 		 * obviously never come because we've
5590 		 * unplugged the device, but the wait will
5591 		 * wait forever because no interrupts can
5592 		 * come in...
5593 		 */
5594 #ifdef CARDBUS
5595 		    pcic_unload_cardbus(pcic, sockp);
5596 		    /* pcic_dump_all(pcic); */
5597 #endif
5598 		    sockp->pcs_flags &= ~PCS_CARD_CBREM;
5599 		}
5600 		syshw_send_signal(sockp->pcs_syshwsig);
5601 		sockp->pcs_flags &= ~PCS_CARD_REMOVED;
5602 	    }
5603 	    break;
5604 	} /* switch */
5605 
5606 	if (do_debounce) {
5607 	/*
5608 	 * Delay doing
5609 	 * anything for a while so that things can settle
5610 	 * down a little. Interrupts are already disabled.
5611 	 * Reset the state and we'll reevaluate the
5612 	 * whole kit 'n kaboodle when the timeout fires
5613 	 */
5614 #ifdef PCIC_DEBUG
5615 		pcic_err(pcic->dip, 8, "Queueing up debounce timeout for "
5616 			"socket %d.%d\n",
5617 			ddi_get_instance(pcic->dip),
5618 			sockp->pcs_socket);
5619 #endif
5620 	    sockp->pcs_debounce_id = pcic_add_debqueue(sockp, debounce_time);
5621 
5622 	/*
5623 	 * We bug out here without re-enabling interrupts. They will
5624 	 * be re-enabled when the debounce timeout swings through
5625 	 * here.
5626 	 */
5627 	    return;
5628 	}
5629 
5630 	/*
5631 	 * Turn on Card detect interrupts. Other interrupts will be
5632 	 * enabled during set_socket calls.
5633 	 *
5634 	 * Note that set_socket only changes interrupt settings when there
5635 	 * is a card present.
5636 	 */
5637 	irq = pcic_getb(pcic, sockp->pcs_socket, PCIC_MANAGEMENT_INT);
5638 	irq |= PCIC_CD_DETECT;
5639 	pcic_putb(pcic, sockp->pcs_socket, PCIC_MANAGEMENT_INT, irq);
5640 	pcic_putcb(pcic, CB_STATUS_MASK, CB_SE_CCDMASK);
5641 
5642 	/* Out from debouncing state */
5643 	sockp->pcs_flags &= ~PCS_DEBOUNCING;
5644 
5645 	pcic_err(pcic->dip, 7, "Leaving pcic_handle_cd_change\n");
5646 }
5647 
5648 /*
5649  * pcic_getb()
5650  *	get an I/O byte based on the yardware decode method
5651  */
5652 static uint8_t
5653 pcic_getb(pcicdev_t *pcic, int socket, int reg)
5654 {
5655 	int work;
5656 
5657 #if defined(PCIC_DEBUG)
5658 	if (pcic_debug == 0x7fff) {
5659 		cmn_err(CE_CONT, "pcic_getb0: pcic=%p socket=%d reg=%d\n",
5660 			(void *)pcic, socket, reg);
5661 		cmn_err(CE_CONT, "pcic_getb1: type=%d handle=%p ioaddr=%p \n",
5662 			pcic->pc_io_type, (void *)pcic->handle,
5663 			(void *)pcic->ioaddr);
5664 	}
5665 #endif
5666 
5667 	switch (pcic->pc_io_type) {
5668 	case PCIC_IO_TYPE_YENTA:
5669 		return (ddi_get8(pcic->handle,
5670 		    pcic->ioaddr + CB_R2_OFFSET + reg));
5671 	default:
5672 		work = (socket * PCIC_SOCKET_1) | reg;
5673 		ddi_put8(pcic->handle, pcic->ioaddr, work);
5674 		return (ddi_get8(pcic->handle, pcic->ioaddr + 1));
5675 	}
5676 }
5677 
5678 static void
5679 pcic_putb(pcicdev_t *pcic, int socket, int reg, int8_t value)
5680 {
5681 	int work;
5682 
5683 #if defined(PCIC_DEBUG)
5684 	if (pcic_debug == 0x7fff) {
5685 		cmn_err(CE_CONT,
5686 			"pcic_putb0: pcic=%p socket=%d reg=%d value=%x \n",
5687 			(void *)pcic, socket, reg, value);
5688 		cmn_err(CE_CONT,
5689 			"pcic_putb1: type=%d handle=%p ioaddr=%p \n",
5690 			pcic->pc_io_type, (void *)pcic->handle,
5691 			(void *)pcic->ioaddr);
5692 	}
5693 #endif
5694 
5695 
5696 	switch (pcic->pc_io_type) {
5697 	case PCIC_IO_TYPE_YENTA:
5698 		ddi_put8(pcic->handle, pcic->ioaddr + CB_R2_OFFSET + reg,
5699 				value);
5700 		break;
5701 	default:
5702 		work = (socket * PCIC_SOCKET_1) | reg;
5703 		ddi_put8(pcic->handle, pcic->ioaddr, work);
5704 		ddi_put8(pcic->handle, pcic->ioaddr + 1, value);
5705 		break;
5706 	}
5707 }
5708 
5709 /*
5710  * chip identification functions
5711  */
5712 
5713 /*
5714  * chip identification: Cirrus Logic PD6710/6720/6722
5715  */
5716 static int
5717 pcic_ci_cirrus(pcicdev_t *pcic)
5718 {
5719 	int value1, value2;
5720 
5721 	/* Init the CL id mode */
5722 	value1 = pcic_getb(pcic, 0, PCIC_CHIP_INFO);
5723 	pcic_putb(pcic, 0, PCIC_CHIP_INFO, 0);
5724 	value1 = pcic_getb(pcic, 0, PCIC_CHIP_INFO);
5725 	value2 = pcic_getb(pcic, 0, PCIC_CHIP_INFO);
5726 
5727 	if ((value1 & PCIC_CI_ID) == PCIC_CI_ID &&
5728 	    (value2 & PCIC_CI_ID) == 0) {
5729 		/* chip is a Cirrus Logic and not Intel */
5730 		pcic->pc_type = PCIC_CL_PD6710;
5731 		if (value1 & PCIC_CI_SLOTS)
5732 			pcic->pc_chipname = PCIC_TYPE_PD6720;
5733 		else
5734 			pcic->pc_chipname = PCIC_TYPE_PD6710;
5735 		/* now fine tune things just in case a 6722 */
5736 		value1 = clext_reg_read(pcic, 0, PCIC_CLEXT_DMASK_0);
5737 		if (value1 == 0) {
5738 			clext_reg_write(pcic, 0, PCIC_CLEXT_SCRATCH, 0x55);
5739 			value1 = clext_reg_read(pcic, 0, PCIC_CLEXT_SCRATCH);
5740 			if (value1 == 0x55) {
5741 				pcic->pc_chipname = PCIC_TYPE_PD6722;
5742 				pcic->pc_type = PCIC_CL_PD6722;
5743 				clext_reg_write(pcic, 0, PCIC_CLEXT_SCRATCH, 0);
5744 			}
5745 		}
5746 		return (1);
5747 	}
5748 	return (0);
5749 }
5750 
5751 /*
5752  * chip identification: Vadem (VG365/465/468/469)
5753  */
5754 
5755 static void
5756 pcic_vadem_enable(pcicdev_t *pcic)
5757 {
5758 	ddi_put8(pcic->handle, pcic->ioaddr, PCIC_VADEM_P1);
5759 	ddi_put8(pcic->handle, pcic->ioaddr, PCIC_VADEM_P2);
5760 	ddi_put8(pcic->handle, pcic->ioaddr, pcic->pc_lastreg);
5761 }
5762 
5763 static int
5764 pcic_ci_vadem(pcicdev_t *pcic)
5765 {
5766 	int value;
5767 
5768 	pcic_vadem_enable(pcic);
5769 	value = pcic_getb(pcic, 0, PCIC_CHIP_REVISION);
5770 	pcic_putb(pcic, 0, PCIC_CHIP_REVISION, 0xFF);
5771 	if (pcic_getb(pcic, 0, PCIC_CHIP_REVISION) ==
5772 	    (value | PCIC_VADEM_D3) ||
5773 	    (pcic_getb(pcic, 0, PCIC_CHIP_REVISION) & PCIC_REV_MASK) ==
5774 	    PCIC_VADEM_469) {
5775 		int vadem, new;
5776 		pcic_vadem_enable(pcic);
5777 		vadem = pcic_getb(pcic, 0, PCIC_VG_DMA) &
5778 			~(PCIC_V_UNLOCK | PCIC_V_VADEMREV);
5779 		new = vadem | (PCIC_V_VADEMREV|PCIC_V_UNLOCK);
5780 		pcic_putb(pcic, 0, PCIC_VG_DMA, new);
5781 		value = pcic_getb(pcic, 0, PCIC_CHIP_REVISION);
5782 
5783 		/* want to lock but leave mouse or other on */
5784 		pcic_putb(pcic, 0, PCIC_VG_DMA, vadem);
5785 		switch (value & PCIC_REV_MASK) {
5786 		case PCIC_VADEM_365:
5787 			pcic->pc_chipname = PCIC_VG_365;
5788 			pcic->pc_type = PCIC_VADEM;
5789 			break;
5790 		case PCIC_VADEM_465:
5791 			pcic->pc_chipname = PCIC_VG_465;
5792 			pcic->pc_type = PCIC_VADEM;
5793 			pcic->pc_flags |= PCF_1SOCKET;
5794 			break;
5795 		case PCIC_VADEM_468:
5796 			pcic->pc_chipname = PCIC_VG_468;
5797 			pcic->pc_type = PCIC_VADEM;
5798 			break;
5799 		case PCIC_VADEM_469:
5800 			pcic->pc_chipname = PCIC_VG_469;
5801 			pcic->pc_type = PCIC_VADEM_VG469;
5802 			break;
5803 		}
5804 		return (1);
5805 	}
5806 	return (0);
5807 }
5808 
5809 /*
5810  * chip identification: Ricoh
5811  */
5812 static int
5813 pcic_ci_ricoh(pcicdev_t *pcic)
5814 {
5815 	int value;
5816 
5817 	value = pcic_getb(pcic, 0, PCIC_RF_CHIP_IDENT);
5818 	switch (value) {
5819 	case PCIC_RF_296:
5820 		pcic->pc_type = PCIC_RICOH;
5821 		pcic->pc_chipname = PCIC_TYPE_RF5C296;
5822 		return (1);
5823 	case PCIC_RF_396:
5824 		pcic->pc_type = PCIC_RICOH;
5825 		pcic->pc_chipname = PCIC_TYPE_RF5C396;
5826 		return (1);
5827 	}
5828 	return (0);
5829 }
5830 
5831 
5832 /*
5833  * set up available address spaces in busra
5834  */
5835 static void
5836 pcic_init_assigned(dev_info_t *dip)
5837 {
5838 	pcm_regs_t *pcic_avail_p;
5839 	pci_regspec_t *pci_avail_p, *regs;
5840 	int len, entries, rlen;
5841 	dev_info_t *pdip;
5842 
5843 	if (ddi_getlongprop(DDI_DEV_T_ANY, dip, DDI_PROP_DONTPASS,
5844 	    "available", (caddr_t)&pcic_avail_p, &len) == DDI_PROP_SUCCESS) {
5845 		/*
5846 		 * found "available" property at the cardbus/pcmcia node
5847 		 * need to translate address space entries from pcmcia
5848 		 * format to pci format
5849 		 */
5850 		entries = len / sizeof (pcm_regs_t);
5851 		pci_avail_p = kmem_alloc(sizeof (pci_regspec_t) * entries,
5852 			KM_SLEEP);
5853 		if (pcic_apply_avail_ranges(dip, pcic_avail_p, pci_avail_p,
5854 		    entries) == DDI_SUCCESS)
5855 			(void) pci_resource_setup_avail(dip, pci_avail_p,
5856 				entries);
5857 		kmem_free(pcic_avail_p, len);
5858 		kmem_free(pci_avail_p, entries * sizeof (pci_regspec_t));
5859 		return;
5860 	}
5861 
5862 	/*
5863 	 * "legacy" platforms will have "available" property in pci node
5864 	 */
5865 	for (pdip = ddi_get_parent(dip); pdip; pdip = ddi_get_parent(pdip)) {
5866 		if (ddi_getlongprop(DDI_DEV_T_ANY, pdip, DDI_PROP_DONTPASS,
5867 		    "available", (caddr_t)&pci_avail_p, &len) ==
5868 		    DDI_PROP_SUCCESS) {
5869 			/* (void) pci_resource_setup(pdip); */
5870 			kmem_free(pci_avail_p, len);
5871 			break;
5872 		}
5873 	}
5874 
5875 	if (pdip == NULL) {
5876 		int len;
5877 		char bus_type[16] = "(unknown)";
5878 		dev_info_t *par;
5879 
5880 		cmn_err(CE_CONT,
5881 		    "?pcic_init_assigned: no available property for pcmcia\n");
5882 
5883 		/*
5884 		 * This code is taken from pci_resource_setup() but does
5885 		 * not attempt to use the "available" property to populate
5886 		 * the ndi maps that are created.
5887 		 * The fact that we will actually
5888 		 * free some resource below (that was allocated by OBP)
5889 		 * should be enough to be going on with.
5890 		 */
5891 		for (par = dip; par != NULL; par = ddi_get_parent(par)) {
5892 			len = sizeof (bus_type);
5893 
5894 			if ((ddi_prop_op(DDI_DEV_T_ANY, par,
5895 			    PROP_LEN_AND_VAL_BUF,
5896 			    DDI_PROP_CANSLEEP | DDI_PROP_DONTPASS,
5897 			    "device_type",
5898 			    (caddr_t)&bus_type, &len) == DDI_SUCCESS) &&
5899 			    (strcmp(bus_type, "pci") == 0))
5900 				break;
5901 		}
5902 		if (par != NULL &&
5903 		    (ndi_ra_map_setup(par, NDI_RA_TYPE_MEM) != NDI_SUCCESS ||
5904 		    ndi_ra_map_setup(par, NDI_RA_TYPE_IO) != NDI_SUCCESS))
5905 			par = NULL;
5906 	} else {
5907 #ifdef CARDBUS
5908 		cardbus_bus_range_t *bus_range;
5909 		int k;
5910 
5911 		if (ddi_getlongprop(DDI_DEV_T_ANY, pdip, 0, "bus-range",
5912 		    (caddr_t)&bus_range, &k) == DDI_PROP_SUCCESS) {
5913 			if (bus_range->lo != bus_range->hi)
5914 				pcic_err(pdip, 9, "allowable bus range is "
5915 				    "%u->%u\n", bus_range->lo, bus_range->hi);
5916 			else {
5917 				pcic_err(pdip, 0,
5918 				    "!No spare PCI bus numbers, range is "
5919 				    "%u->%u, cardbus isn't usable\n",
5920 				    bus_range->lo, bus_range->hi);
5921 			}
5922 			kmem_free(bus_range, k);
5923 		} else
5924 			pcic_err(pdip, 0, "!No bus-range property seems to "
5925 			    "have been set up\n");
5926 #endif
5927 		/*
5928 		 * Have a valid parent with the "available" property
5929 		 */
5930 		(void) pci_resource_setup(pdip);
5931 	}
5932 
5933 	if ((strcmp(ddi_get_name(dip), "pcma") == 0) &&
5934 	    ddi_getlongprop(DDI_DEV_T_NONE, dip, DDI_PROP_DONTPASS,
5935 	    "assigned-addresses",
5936 	    (caddr_t)&regs, &rlen) == DDI_SUCCESS) {
5937 		ra_return_t ra;
5938 
5939 		/*
5940 		 * On the UltraBook IIi the ranges are assigned under
5941 		 * openboot. If we don't free them here the first I/O
5942 		 * space that can be used is up above 0x10000 which
5943 		 * doesn't work for this driver due to restrictions
5944 		 * on the PCI I/O addresses the controllers can cope with.
5945 		 * They are never going to be used by anything else
5946 		 * so free them up to the general pool. AG.
5947 		 */
5948 		pcic_err(dip, 1, "Free assigned addresses\n");
5949 
5950 		if ((PCI_REG_ADDR_G(regs[0].pci_phys_hi) ==
5951 		    PCI_REG_ADDR_G(PCI_ADDR_MEM32)) &&
5952 		    regs[0].pci_size_low == 0x1000000) {
5953 			ra.ra_addr_lo = regs[0].pci_phys_low;
5954 			ra.ra_len = regs[0].pci_size_low;
5955 			(void) pcmcia_free_mem(dip, &ra);
5956 		}
5957 		if ((PCI_REG_ADDR_G(regs[1].pci_phys_hi) ==
5958 		    PCI_REG_ADDR_G(PCI_ADDR_IO)) &&
5959 		    (regs[1].pci_size_low == 0x8000 ||
5960 		    regs[1].pci_size_low == 0x4000))   /* UB-IIi || UB-I */
5961 		{
5962 			ra.ra_addr_lo = regs[1].pci_phys_low;
5963 			ra.ra_len = regs[1].pci_size_low;
5964 			(void) pcmcia_free_io(dip, &ra);
5965 		}
5966 		kmem_free((caddr_t)regs, rlen);
5967 	}
5968 }
5969 
5970 /*
5971  * translate "available" from pcmcia format to pci format
5972  */
5973 static int
5974 pcic_apply_avail_ranges(dev_info_t *dip, pcm_regs_t *pcic_p,
5975     pci_regspec_t *pci_p, int entries)
5976 {
5977 	int i, range_len, range_entries;
5978 	pcic_ranges_t *pcic_range_p;
5979 
5980 	if (ddi_getlongprop(DDI_DEV_T_ANY, dip, DDI_PROP_DONTPASS, "ranges",
5981 		    (caddr_t)&pcic_range_p, &range_len) != DDI_PROP_SUCCESS) {
5982 		cmn_err(CE_CONT, "?pcic_apply_avail_ranges: "
5983 			"no ranges property for pcmcia\n");
5984 		return (DDI_FAILURE);
5985 	}
5986 
5987 	range_entries = range_len / sizeof (pcic_ranges_t);
5988 
5989 	/* for each "available" entry to be translated */
5990 	for (i = 0; i < entries; i++, pcic_p++, pci_p++) {
5991 		int j;
5992 		pcic_ranges_t *range_p = pcic_range_p;
5993 		pci_p->pci_phys_hi = -1u; /* default invalid value */
5994 
5995 		/* for each "ranges" entry to be searched */
5996 		for (j = 0; j < range_entries; j++, range_p++) {
5997 			uint64_t range_end = range_p->pcic_range_caddrlo +
5998 				range_p->pcic_range_size;
5999 			uint64_t avail_end = pcic_p->phys_lo + pcic_p->phys_len;
6000 
6001 			if ((range_p->pcic_range_caddrhi != pcic_p->phys_hi) ||
6002 			    (range_p->pcic_range_caddrlo > pcic_p->phys_lo) ||
6003 			    (range_end < avail_end))
6004 				continue;
6005 
6006 			pci_p->pci_phys_hi = range_p->pcic_range_paddrhi;
6007 			pci_p->pci_phys_mid = range_p->pcic_range_paddrmid;
6008 			pci_p->pci_phys_low = range_p->pcic_range_paddrlo
6009 			    + (pcic_p->phys_lo - range_p->pcic_range_caddrlo);
6010 			pci_p->pci_size_hi = 0;
6011 			pci_p->pci_size_low = pcic_p->phys_len;
6012 		}
6013 	}
6014 	kmem_free(pcic_range_p, range_len);
6015 	return (DDI_SUCCESS);
6016 }
6017 
6018 static int
6019 pcic_open(dev_t *dev, int flag, int otyp, cred_t *cred)
6020 {
6021 	if (getminor(*dev) == SYSHW_MINOR)
6022 		return (syshw_open(dev, flag, otyp, cred));
6023 #ifdef CARDBUS
6024 	if (cardbus_is_cb_minor(*dev))
6025 		return (cardbus_open(dev, flag, otyp, cred));
6026 #endif
6027 	return (EINVAL);
6028 }
6029 
6030 static int
6031 pcic_close(dev_t dev, int flag, int otyp, cred_t *cred)
6032 {
6033 	if (getminor(dev) == SYSHW_MINOR)
6034 		return (syshw_close(dev, flag, otyp, cred));
6035 #ifdef CARDBUS
6036 	if (cardbus_is_cb_minor(dev))
6037 		return (cardbus_close(dev, flag, otyp, cred));
6038 #endif
6039 	return (EINVAL);
6040 }
6041 
6042 static int
6043 pcic_ioctl(dev_t dev, int cmd, intptr_t arg, int mode, cred_t *cred,
6044 	int *rval)
6045 {
6046 	if (getminor(dev) == SYSHW_MINOR)
6047 		return (syshw_ioctl(dev, cmd, arg, mode, cred, rval));
6048 #ifdef CARDBUS
6049 	if (cardbus_is_cb_minor(dev))
6050 		return (cardbus_ioctl(dev, cmd, arg, mode, cred, rval));
6051 #endif
6052 	return (EINVAL);
6053 }
6054 
6055 
6056 static boolean_t
6057 pcic_load_cardbus(pcicdev_t *pcic, const pcic_socket_t *sockp)
6058 {
6059 	uint32_t present_state;
6060 	dev_info_t *dip = pcic->dip;
6061 	set_socket_t s;
6062 	get_socket_t g;
6063 	boolean_t retval;
6064 	unsigned vccLevel;
6065 
6066 	pcic_err(dip, 8, "entering pcic_load_cardbus\n");
6067 
6068 	pcic_mutex_exit(&pcic->pc_lock);
6069 
6070 	bzero(&s, sizeof (set_socket_t));
6071 	s.socket = sockp->pcs_socket;
6072 	s.SCIntMask = SBM_CD|SBM_RDYBSY;
6073 	s.IFType = IF_CARDBUS;
6074 	s.State = (unsigned)~0;
6075 
6076 	present_state = pcic_getcb(pcic, CB_PRESENT_STATE);
6077 	if (present_state & PCIC_VCC_3VCARD)
6078 		s.VccLevel = PCIC_VCC_3VLEVEL;
6079 	else if (present_state & PCIC_VCC_5VCARD)
6080 		s.VccLevel = PCIC_VCC_5VLEVEL;
6081 	else {
6082 		cmn_err(CE_CONT,
6083 		    "pcic_load_cardbus: unsupported card voltage\n");
6084 		goto failure;
6085 	}
6086 	vccLevel = s.VccLevel;
6087 	s.Vpp1Level = s.Vpp2Level = 0;
6088 
6089 	if (pcic_set_socket(dip, &s) != SUCCESS)
6090 		goto failure;
6091 
6092 	if (pcic_reset_socket(dip, sockp->pcs_socket,
6093 	    RESET_MODE_CARD_ONLY) != SUCCESS)
6094 		goto failure;
6095 
6096 	bzero(&g, sizeof (get_socket_t));
6097 	g.socket = sockp->pcs_socket;
6098 	if (pcic_get_socket(dip, &g) != SUCCESS)
6099 		goto failure;
6100 
6101 	bzero(&s, sizeof (set_socket_t));
6102 	s.socket = sockp->pcs_socket;
6103 	s.SCIntMask = SBM_CD;
6104 	s.IREQRouting = g.IRQRouting;
6105 	s.IFType = g.IFType;
6106 	s.CtlInd = g.CtlInd;
6107 	s.State = (unsigned)~0;
6108 	s.VccLevel = vccLevel;
6109 	s.Vpp1Level = s.Vpp2Level = 0;
6110 
6111 	if (pcic_set_socket(dip, &s) != SUCCESS)
6112 		goto failure;
6113 
6114 	retval = cardbus_load_cardbus(dip, sockp->pcs_socket, pcic->pc_base);
6115 	goto exit;
6116 
6117 failure:
6118 	retval = B_FALSE;
6119 
6120 exit:
6121 	pcic_mutex_enter(&pcic->pc_lock);
6122 	pcic_err(dip, 8, "exit pcic_load_cardbus (%s)\n",
6123 	    retval ? "success" : "failure");
6124 	return (retval);
6125 }
6126 
6127 static void
6128 pcic_unload_cardbus(pcicdev_t *pcic, const pcic_socket_t *sockp)
6129 {
6130 	dev_info_t *dip = pcic->dip;
6131 	set_socket_t s;
6132 
6133 	pcic_mutex_exit(&pcic->pc_lock);
6134 
6135 	cardbus_unload_cardbus(dip);
6136 
6137 	bzero(&s, sizeof (set_socket_t));
6138 	s.socket = sockp->pcs_socket;
6139 	s.SCIntMask = SBM_CD|SBM_RDYBSY;
6140 	s.IREQRouting = 0;
6141 	s.IFType = IF_MEMORY;
6142 	s.CtlInd = 0;
6143 	s.State = 0;
6144 	s.VccLevel = s.Vpp1Level = s.Vpp2Level = 0;
6145 
6146 	(void) pcic_set_socket(dip, &s);
6147 
6148 	pcic_mutex_enter(&pcic->pc_lock);
6149 }
6150 
6151 static uint32_t
6152 pcic_getcb(pcicdev_t *pcic, int reg)
6153 {
6154 	ASSERT(pcic->pc_io_type == PCIC_IO_TYPE_YENTA);
6155 
6156 	return (ddi_get32(pcic->handle,
6157 	    (uint32_t *)(pcic->ioaddr + CB_CB_OFFSET + reg)));
6158 }
6159 
6160 static void
6161 pcic_putcb(pcicdev_t *pcic, int reg, uint32_t value)
6162 {
6163 	ASSERT(pcic->pc_io_type == PCIC_IO_TYPE_YENTA);
6164 
6165 	ddi_put32(pcic->handle,
6166 	    (uint32_t *)(pcic->ioaddr + CB_CB_OFFSET + reg), value);
6167 }
6168 
6169 static void
6170 pcic_enable_io_intr(pcicdev_t *pcic, int socket, int irq)
6171 {
6172 	uint8_t value;
6173 	uint16_t brdgctl;
6174 
6175 	value = pcic_getb(pcic, socket, PCIC_INTERRUPT) & ~PCIC_INTR_MASK;
6176 	pcic_putb(pcic, socket, PCIC_INTERRUPT, value | irq);
6177 
6178 	switch (pcic->pc_type) {
6179 	case PCIC_INTEL_i82092:
6180 		pcic_82092_smiirq_ctl(pcic, socket, PCIC_82092_CTL_IRQ,
6181 		    PCIC_82092_INT_ENABLE);
6182 		break;
6183 	case PCIC_O2_OZ6912:
6184 		value = pcic_getb(pcic, 0, PCIC_CENTDMA);
6185 		value |= 0x8;
6186 		pcic_putb(pcic, 0, PCIC_CENTDMA, value);
6187 		break;
6188 	case PCIC_CL_PD6832:
6189 	case PCIC_TI_PCI1250:
6190 	case PCIC_TI_PCI1221:
6191 	case PCIC_TI_PCI1225:
6192 	case PCIC_TI_PCI1410:
6193 	case PCIC_ENE_1410:
6194 	case PCIC_TI_PCI1510:
6195 	case PCIC_TI_PCI1520:
6196 	case PCIC_TI_PCI1420:
6197 	case PCIC_ENE_1420:
6198 		/* route card functional interrupts to PCI interrupts */
6199 		brdgctl = ddi_get16(pcic->cfg_handle,
6200 		    (uint16_t *)(pcic->cfgaddr + PCI_CBUS_BRIDGE_CTRL));
6201 		pcic_err(NULL, 1,
6202 		    "pcic_enable_io_intr brdgctl(0x%x) was: 0x%x\n",
6203 		    PCI_CBUS_BRIDGE_CTRL, brdgctl);
6204 		brdgctl &= ~PCIC_BRDGCTL_INTR_MASK;
6205 		ddi_put16(pcic->cfg_handle,
6206 		    (uint16_t *)(pcic->cfgaddr + PCI_CBUS_BRIDGE_CTRL),
6207 		    brdgctl);
6208 		/* Flush the write */
6209 		(void) ddi_get16(pcic->cfg_handle,
6210 		    (uint16_t *)(pcic->cfgaddr + PCI_CBUS_BRIDGE_CTRL));
6211 		break;
6212 	default:
6213 		break;
6214 	}
6215 }
6216 
6217 static void
6218 pcic_disable_io_intr(pcicdev_t *pcic, int socket)
6219 {
6220 	uint8_t value;
6221 	uint16_t brdgctl;
6222 
6223 	value = pcic_getb(pcic, socket, PCIC_INTERRUPT) & ~PCIC_INTR_MASK;
6224 	pcic_putb(pcic, socket, PCIC_INTERRUPT, value);
6225 
6226 	switch (pcic->pc_type) {
6227 	case PCIC_INTEL_i82092:
6228 		pcic_82092_smiirq_ctl(pcic, socket, PCIC_82092_CTL_IRQ,
6229 		    PCIC_82092_INT_DISABLE);
6230 		break;
6231 	case PCIC_O2_OZ6912:
6232 		value = pcic_getb(pcic, 0, PCIC_CENTDMA);
6233 		value &= ~0x8;
6234 		pcic_putb(pcic, 0, PCIC_CENTDMA, value);
6235 		/* Flush the write */
6236 		(void) pcic_getb(pcic, 0, PCIC_CENTDMA);
6237 		break;
6238 	case PCIC_CL_PD6832:
6239 	case PCIC_TI_PCI1250:
6240 	case PCIC_TI_PCI1221:
6241 	case PCIC_TI_PCI1225:
6242 	case PCIC_TI_PCI1410:
6243 	case PCIC_ENE_1410:
6244 	case PCIC_TI_PCI1510:
6245 	case PCIC_TI_PCI1520:
6246 	case PCIC_TI_PCI1420:
6247 	case PCIC_ENE_1420:
6248 		/*
6249 		 * This maps I/O interrupts to ExCA which
6250 		 * have been turned off by the write to
6251 		 * PCIC_INTERRUPT above. It would appear to
6252 		 * be the only way to actually turn I/O Ints off
6253 		 * while retaining CS Ints.
6254 		 */
6255 		brdgctl = ddi_get16(pcic->cfg_handle,
6256 		    (uint16_t *)(pcic->cfgaddr + PCI_CBUS_BRIDGE_CTRL));
6257 		pcic_err(NULL, 1,
6258 		    "pcic_disable_io_intr brdgctl(0x%x) was: 0x%x\n",
6259 		    PCI_CBUS_BRIDGE_CTRL, brdgctl);
6260 		brdgctl |= PCIC_BRDGCTL_INTR_MASK;
6261 		ddi_put16(pcic->cfg_handle,
6262 		    (uint16_t *)(pcic->cfgaddr + PCI_CBUS_BRIDGE_CTRL),
6263 		    brdgctl);
6264 		/* Flush the write */
6265 		(void) ddi_get16(pcic->cfg_handle,
6266 		    (uint16_t *)(pcic->cfgaddr + PCI_CBUS_BRIDGE_CTRL));
6267 		break;
6268 	default:
6269 		break;
6270 	}
6271 }
6272 
6273 static void
6274 pcic_cb_enable_intr(dev_info_t *dip)
6275 {
6276 	anp_t *anp = ddi_get_driver_private(dip);
6277 	pcicdev_t *pcic = anp->an_private;
6278 
6279 	mutex_enter(&pcic->pc_lock);
6280 	pcic_enable_io_intr(pcic, 0, pcic->pc_sockets[0].pcs_irq);
6281 	mutex_exit(&pcic->pc_lock);
6282 }
6283 
6284 static void
6285 pcic_cb_disable_intr(dev_info_t *dip)
6286 {
6287 	anp_t *anp = ddi_get_driver_private(dip);
6288 	pcicdev_t *pcic = anp->an_private;
6289 
6290 	mutex_enter(&pcic->pc_lock);
6291 	pcic_disable_io_intr(pcic, 0);
6292 	mutex_exit(&pcic->pc_lock);
6293 }
6294 
6295 static int
6296 log_pci_cfg_err(ushort_t e, int bridge_secondary)
6297 {
6298 	int	nerr = 0;
6299 	if (e & PCI_STAT_PERROR) {
6300 		nerr++;
6301 		cmn_err(CE_CONT, "detected parity error.\n");
6302 	}
6303 	if (e & PCI_STAT_S_SYSERR) {
6304 		nerr++;
6305 		if (bridge_secondary)
6306 			cmn_err(CE_CONT, "received system error.\n");
6307 		else
6308 			cmn_err(CE_CONT, "signalled system error.\n");
6309 	}
6310 	if (e & PCI_STAT_R_MAST_AB) {
6311 		nerr++;
6312 		cmn_err(CE_CONT, "received master abort.\n");
6313 	}
6314 	if (e & PCI_STAT_R_TARG_AB)
6315 		cmn_err(CE_CONT, "received target abort.\n");
6316 	if (e & PCI_STAT_S_TARG_AB)
6317 		cmn_err(CE_CONT, "signalled target abort\n");
6318 	if (e & PCI_STAT_S_PERROR) {
6319 		nerr++;
6320 		cmn_err(CE_CONT, "signalled parity error\n");
6321 	}
6322 	return (nerr);
6323 }
6324 
6325 #if defined(__sparc)
6326 static int
6327 pcic_fault(enum pci_fault_ops op, void *arg)
6328 {
6329 	pcicdev_t *pcic = (pcicdev_t *)arg;
6330 	ushort_t pci_cfg_stat =
6331 	    pci_config_get16(pcic->cfg_handle, PCI_CONF_STAT);
6332 	ushort_t pci_cfg_sec_stat =
6333 	    pci_config_get16(pcic->cfg_handle, 0x16);
6334 	char	nm[24];
6335 	int	nerr = 0;
6336 
6337 	cardbus_dump_pci_config(pcic->dip);
6338 
6339 	switch (op) {
6340 	case FAULT_LOG:
6341 		(void) sprintf(nm, "%s-%d", ddi_driver_name(pcic->dip),
6342 		    ddi_get_instance(pcic->dip));
6343 
6344 		cmn_err(CE_WARN, "%s: PCIC fault log start:\n", nm);
6345 		cmn_err(CE_WARN, "%s: primary err (%x):\n", nm, pci_cfg_stat);
6346 		nerr += log_pci_cfg_err(pci_cfg_stat, 0);
6347 		cmn_err(CE_WARN, "%s: sec err (%x):\n", nm, pci_cfg_sec_stat);
6348 		nerr += log_pci_cfg_err(pci_cfg_sec_stat, 1);
6349 		cmn_err(CE_CONT, "%s: PCI fault log end.\n", nm);
6350 		return (nerr);
6351 	case FAULT_POKEFINI:
6352 	case FAULT_RESET:
6353 		pci_config_put16(pcic->cfg_handle,
6354 		    PCI_CONF_STAT, pci_cfg_stat);
6355 		pci_config_put16(pcic->cfg_handle, 0x16, pci_cfg_sec_stat);
6356 		break;
6357 	case FAULT_POKEFLT:
6358 		if (!(pci_cfg_stat & PCI_STAT_S_SYSERR))
6359 			return (1);
6360 		if (!(pci_cfg_sec_stat & PCI_STAT_R_MAST_AB))
6361 			return (1);
6362 		break;
6363 	default:
6364 		break;
6365 	}
6366 	return (DDI_SUCCESS);
6367 }
6368 #endif
6369 
6370 static void
6371 pcic_delayed_resume(void *arg)
6372 {
6373 	int	i, j, interrupt;
6374 	anp_t *pcic_nexus;
6375 	pcicdev_t *pcic;
6376 
6377 	_NOTE(ARGUNUSED(arg))
6378 
6379 #if defined(PCIC_DEBUG)
6380 	pcic_err(NULL, 6, "pcic_delayed_resume(): entered\n");
6381 #endif
6382 	for (j = 0; j <= pcic_maxinst; j++) {
6383 
6384 		pcic_nexus = ddi_get_soft_state(pcic_soft_state_p, j);
6385 		if (!pcic_nexus)
6386 			continue;
6387 		pcic = (pcicdev_t *)pcic_nexus->an_private;
6388 		if (!pcic)
6389 			continue;
6390 
6391 		pcic_mutex_enter(&pcic->pc_lock); /* protect the registers */
6392 		for (i = 0; i < pcic->pc_numsockets; i++) {
6393 			/* Enable interrupts  on PCI if needs be */
6394 			interrupt = pcic_getb(pcic, i, PCIC_INTERRUPT);
6395 			if (pcic->pc_flags & PCF_USE_SMI)
6396 				interrupt |= PCIC_INTR_ENABLE;
6397 			pcic_putb(pcic, i, PCIC_INTERRUPT,
6398 			    PCIC_RESET | interrupt);
6399 			pcic->pc_sockets[i].pcs_debounce_id =
6400 			    pcic_add_debqueue(&pcic->pc_sockets[i],
6401 			    drv_usectohz(pcic_debounce_time));
6402 		}
6403 		pcic_mutex_exit(&pcic->pc_lock); /* protect the registers */
6404 		if (pcic_do_pcmcia_sr)
6405 			(void) pcmcia_wait_insert(pcic->dip);
6406 	}
6407 }
6408 
6409 static void
6410 pcic_debounce(pcic_socket_t *pcs)
6411 {
6412 	uint8_t status, stschng;
6413 
6414 	pcic_mutex_enter(&pcs->pcs_pcic->pc_lock);
6415 	pcs->pcs_flags &= ~PCS_STARTING;
6416 	stschng = pcic_getb(pcs->pcs_pcic, pcs->pcs_socket,
6417 	    PCIC_CARD_STATUS_CHANGE);
6418 	status = pcic_getb(pcs->pcs_pcic, pcs->pcs_socket,
6419 	    PCIC_INTERFACE_STATUS);
6420 #ifdef PCIC_DEBUG
6421 	pcic_err(pcs->pcs_pcic->dip, 8,
6422 	    "pcic_debounce(0x%p, dip=0x%p) socket %d st 0x%x "
6423 	    "chg 0x%x flg 0x%x\n",
6424 	    (void *)pcs, (void *) pcs->pcs_pcic->dip, pcs->pcs_socket,
6425 	    status, stschng, pcs->pcs_flags);
6426 #endif
6427 
6428 	pcic_putb(pcs->pcs_pcic, pcs->pcs_socket, PCIC_CARD_STATUS_CHANGE,
6429 	    PCIC_CD_DETECT);
6430 	pcic_handle_cd_change(pcs->pcs_pcic, pcs, status);
6431 	pcic_mutex_exit(&pcs->pcs_pcic->pc_lock);
6432 }
6433 
6434 static void
6435 pcic_deb_thread()
6436 {
6437 	callb_cpr_t cprinfo;
6438 	struct debounce *debp;
6439 	clock_t lastt;
6440 
6441 	CALLB_CPR_INIT(&cprinfo, &pcic_deb_mtx,
6442 	    callb_generic_cpr, "pcic debounce thread");
6443 	mutex_enter(&pcic_deb_mtx);
6444 	while (pcic_deb_threadid) {
6445 		while (pcic_deb_queue) {
6446 #ifdef PCIC_DEBUG
6447 			pcic_dump_debqueue("Thread");
6448 #endif
6449 			debp = pcic_deb_queue;
6450 			(void) drv_getparm(LBOLT, &lastt);
6451 			if (lastt >= debp->expire) {
6452 				pcic_deb_queue = debp->next;
6453 				mutex_exit(&pcic_deb_mtx);
6454 				pcic_debounce(debp->pcs);
6455 				mutex_enter(&pcic_deb_mtx);
6456 				kmem_free(debp, sizeof (*debp));
6457 			} else {
6458 				(void) cv_timedwait(&pcic_deb_cv,
6459 				    &pcic_deb_mtx, debp->expire);
6460 			}
6461 		}
6462 		CALLB_CPR_SAFE_BEGIN(&cprinfo);
6463 		cv_wait(&pcic_deb_cv, &pcic_deb_mtx);
6464 		CALLB_CPR_SAFE_END(&cprinfo, &pcic_deb_mtx);
6465 	}
6466 	pcic_deb_threadid = (kthread_t *)1;
6467 	cv_signal(&pcic_deb_cv);
6468 	CALLB_CPR_EXIT(&cprinfo);	/* Also exits the mutex */
6469 	thread_exit();
6470 }
6471 
6472 static void *
6473 pcic_add_debqueue(pcic_socket_t *pcs, int clocks)
6474 {
6475 	clock_t lbolt;
6476 	struct debounce *dbp, **dbpp = &pcic_deb_queue;
6477 
6478 	(void) drv_getparm(LBOLT, &lbolt);
6479 	dbp = kmem_alloc(sizeof (struct debounce), KM_NOSLEEP);
6480 
6481 	dbp->expire = lbolt + clocks;
6482 	dbp->pcs = pcs;
6483 	mutex_enter(&pcic_deb_mtx);
6484 	while (*dbpp) {
6485 		if (dbp->expire > (*dbpp)->expire)
6486 			dbpp = &((*dbpp)->next);
6487 		else
6488 			break;
6489 	}
6490 	dbp->next = *dbpp;
6491 	*dbpp = dbp;
6492 #ifdef PCIC_DEBUG
6493 	pcic_dump_debqueue("Add");
6494 #endif
6495 	cv_signal(&pcic_deb_cv);
6496 	mutex_exit(&pcic_deb_mtx);
6497 	return (dbp);
6498 }
6499 
6500 static void
6501 pcic_rm_debqueue(void *id)
6502 {
6503 	struct debounce *dbp, **dbpp = &pcic_deb_queue;
6504 
6505 	dbp = (struct debounce *)id;
6506 	mutex_enter(&pcic_deb_mtx);
6507 	while (*dbpp) {
6508 		if (*dbpp == dbp) {
6509 			*dbpp = dbp->next;
6510 			kmem_free(dbp, sizeof (*dbp));
6511 #ifdef PCIC_DEBUG
6512 			pcic_dump_debqueue("Remove");
6513 #endif
6514 			cv_signal(&pcic_deb_cv);
6515 			mutex_exit(&pcic_deb_mtx);
6516 			return;
6517 		}
6518 		dbpp = &((*dbpp)->next);
6519 	}
6520 	pcic_err(NULL, 6, "pcic: Failed to find debounce id 0x%p\n", id);
6521 	mutex_exit(&pcic_deb_mtx);
6522 }
6523 
6524 
6525 static int	pcic_powerdelay = 0;
6526 
6527 static int
6528 pcic_exca_powerctl(pcicdev_t *pcic, int socket, int powerlevel)
6529 {
6530 	int	ind, value, orig_pwrctl;
6531 
6532 	/* power setup -- if necessary */
6533 	orig_pwrctl = pcic_getb(pcic, socket, PCIC_POWER_CONTROL);
6534 
6535 #if defined(PCIC_DEBUG)
6536 	pcic_err(pcic->dip, 6,
6537 	    "pcic_exca_powerctl(socket %d) powerlevel=%x orig 0x%x\n",
6538 	    socket, powerlevel, orig_pwrctl);
6539 #endif
6540 	/* Preserve the PCIC_OUTPUT_ENABLE (control lines output enable) bit. */
6541 	powerlevel = (powerlevel & ~POWER_OUTPUT_ENABLE) |
6542 	    (orig_pwrctl & POWER_OUTPUT_ENABLE);
6543 	if (powerlevel != orig_pwrctl) {
6544 		if (powerlevel & ~POWER_OUTPUT_ENABLE) {
6545 			int	ifs;
6546 			/*
6547 			 * set power to socket
6548 			 * note that the powerlevel was calculated earlier
6549 			 */
6550 			pcic_putb(pcic, socket, PCIC_POWER_CONTROL, powerlevel);
6551 			(void) pcic_getb(pcic, socket, PCIC_POWER_CONTROL);
6552 
6553 			/*
6554 			 * this second write to the power control register
6555 			 * is needed to resolve a problem on
6556 			 * the IBM ThinkPad 750
6557 			 * where the first write doesn't latch.
6558 			 * The second write appears to always work and
6559 			 * doesn't hurt the operation of other chips
6560 			 * so we can just use it -- this is good since we can't
6561 			 * determine what chip the 750 actually uses
6562 			 * (I suspect an early Ricoh).
6563 			 */
6564 			pcic_putb(pcic, socket, PCIC_POWER_CONTROL, powerlevel);
6565 
6566 			value = pcic_getb(pcic, socket, PCIC_POWER_CONTROL);
6567 			pcic_mswait(pcic, socket, pcic_powerdelay);
6568 #if defined(PCIC_DEBUG)
6569 			pcic_err(pcic->dip, 8,
6570 			    "\tpowerlevel reg = %x (ifs %x)\n",
6571 			    value, pcic_getb(pcic, socket,
6572 			    PCIC_INTERFACE_STATUS));
6573 			pcic_err(pcic->dip, 8,
6574 			    "CBus regs: PS 0x%x, Control 0x%x\n",
6575 			    pcic_getcb(pcic, CB_PRESENT_STATE),
6576 			    pcic_getcb(pcic, CB_CONTROL));
6577 #endif
6578 			/*
6579 			 * since power was touched, make sure it says it
6580 			 * is on.  This lets it become stable.
6581 			 */
6582 			for (ind = 0; ind < 20; ind++) {
6583 				ifs = pcic_getb(pcic, socket,
6584 				    PCIC_INTERFACE_STATUS);
6585 				if (ifs & PCIC_POWER_ON)
6586 					break;
6587 				else {
6588 					pcic_putb(pcic, socket,
6589 					    PCIC_POWER_CONTROL, 0);
6590 					(void) pcic_getb(pcic, socket,
6591 					    PCIC_POWER_CONTROL);
6592 					pcic_mswait(pcic, socket, 40);
6593 					if (ind == 10) {
6594 						pcic_putcb(pcic, CB_EVENT_FORCE,
6595 						    CB_EF_CVTEST);
6596 						pcic_mswait(pcic, socket, 100);
6597 					}
6598 					pcic_putb(pcic, socket,
6599 					    PCIC_POWER_CONTROL,
6600 					    powerlevel & ~POWER_OUTPUT_ENABLE);
6601 					(void) pcic_getb(pcic, socket,
6602 					    PCIC_POWER_CONTROL);
6603 					pcic_mswait(pcic, socket,
6604 					    pcic_powerdelay);
6605 					pcic_putb(pcic, socket,
6606 					    PCIC_POWER_CONTROL, powerlevel);
6607 					(void) pcic_getb(pcic, socket,
6608 					    PCIC_POWER_CONTROL);
6609 					pcic_mswait(pcic, socket,
6610 					    pcic_powerdelay);
6611 				}
6612 			}
6613 
6614 			if (!(ifs & PCIC_POWER_ON)) {
6615 				cmn_err(CE_WARN,
6616 				    "pcic socket %d: Power didn't get turned"
6617 				    "on!\nif status 0x%x pwrc 0x%x(x%x) "
6618 				    "misc1 0x%x igc 0x%x ind %d\n",
6619 				    socket, ifs,
6620 				    pcic_getb(pcic, socket, PCIC_POWER_CONTROL),
6621 				    orig_pwrctl,
6622 				    pcic_getb(pcic, socket, PCIC_MISC_CTL_1),
6623 				    pcic_getb(pcic, socket, PCIC_INTERRUPT),
6624 				    ind);
6625 				return (BAD_VCC);
6626 			}
6627 #if defined(PCIC_DEBUG)
6628 			pcic_err(pcic->dip, 8,
6629 			    "\tind = %d, if status %x pwrc 0x%x "
6630 			    "misc1 0x%x igc 0x%x\n",
6631 			    ind, ifs,
6632 			    pcic_getb(pcic, socket, PCIC_POWER_CONTROL),
6633 			    pcic_getb(pcic, socket, PCIC_MISC_CTL_1),
6634 			    pcic_getb(pcic, socket, PCIC_INTERRUPT));
6635 #endif
6636 		} else {
6637 			/* explicitly turned off the power */
6638 			pcic_putb(pcic, socket, PCIC_POWER_CONTROL, powerlevel);
6639 			(void) pcic_getb(pcic, socket, PCIC_POWER_CONTROL);
6640 		}
6641 	}
6642 	return (SUCCESS);
6643 }
6644 
6645 static int pcic_cbdoreset_during_poweron = 1;
6646 static int
6647 pcic_cbus_powerctl(pcicdev_t *pcic, int socket)
6648 {
6649 	uint32_t cbctl = 0, orig_cbctl, cbstev, cbps;
6650 	int ind, iobits;
6651 	pcic_socket_t *sockp = &pcic->pc_sockets[socket];
6652 
6653 	pcic_putcb(pcic, CB_STATUS_EVENT, CB_SE_POWER_CYCLE);
6654 
6655 	ind = pcic_power[sockp->pcs_vpp1].PowerLevel/10;
6656 	cbctl |= pcic_cbv_levels[ind];
6657 
6658 	ind = pcic_power[sockp->pcs_vcc].PowerLevel/10;
6659 	cbctl |= (pcic_cbv_levels[ind]<<4);
6660 
6661 	orig_cbctl = pcic_getcb(pcic, CB_CONTROL);
6662 
6663 #if defined(PCIC_DEBUG)
6664 	pcic_err(pcic->dip, 6,
6665 	    "pcic_cbus_powerctl(socket %d) vcc %d vpp1 %d "
6666 	    "cbctl 0x%x->0x%x\n",
6667 	    socket, sockp->pcs_vcc, sockp->pcs_vpp1, orig_cbctl, cbctl);
6668 #endif
6669 	if (cbctl != orig_cbctl) {
6670 	    if (pcic_cbdoreset_during_poweron &&
6671 		(orig_cbctl & (CB_C_VCCMASK|CB_C_VPPMASK)) == 0) {
6672 		iobits = pcic_getb(pcic, socket, PCIC_INTERRUPT);
6673 		pcic_putb(pcic, socket, PCIC_INTERRUPT, iobits & ~PCIC_RESET);
6674 	    }
6675 	    pcic_putcb(pcic, CB_CONTROL, cbctl);
6676 
6677 	    if ((cbctl & CB_C_VCCMASK) == (orig_cbctl & CB_C_VCCMASK)) {
6678 		pcic_mswait(pcic, socket, pcic_powerdelay);
6679 		return (SUCCESS);
6680 	    }
6681 	    for (ind = 0; ind < 20; ind++) {
6682 		cbstev = pcic_getcb(pcic, CB_STATUS_EVENT);
6683 
6684 		if (cbstev & CB_SE_POWER_CYCLE) {
6685 
6686 		/*
6687 		 * delay 400 ms: though the standard defines that the Vcc
6688 		 * set-up time is 20 ms, some PC-Card bridge requires longer
6689 		 * duration.
6690 		 * Note: We should check the status AFTER the delay to give time
6691 		 * for things to stabilize.
6692 		 */
6693 		    pcic_mswait(pcic, socket, 400);
6694 
6695 		    cbps = pcic_getcb(pcic, CB_PRESENT_STATE);
6696 		    if (cbctl && !(cbps & CB_PS_POWER_CYCLE)) {
6697 			/* break; */
6698 			cmn_err(CE_WARN, "cbus_powerctl: power off??\n");
6699 		    }
6700 		    if (cbctl & CB_PS_BADVCC) {
6701 			cmn_err(CE_WARN, "cbus_powerctl: bad power request\n");
6702 			break;
6703 		    }
6704 
6705 #if defined(PCIC_DEBUG)
6706 		    pcic_err(pcic->dip, 8,
6707 			"cbstev = 0x%x cbps = 0x%x cbctl 0x%x(0x%x)",
6708 			cbstev, pcic_getcb(pcic, CB_PRESENT_STATE),
6709 			cbctl, orig_cbctl);
6710 #endif
6711 		    if (pcic_cbdoreset_during_poweron &&
6712 			(orig_cbctl & (CB_C_VCCMASK|CB_C_VPPMASK)) == 0) {
6713 			pcic_putb(pcic, socket, PCIC_INTERRUPT, iobits);
6714 		    }
6715 		    return (SUCCESS);
6716 		}
6717 		pcic_mswait(pcic, socket, 40);
6718 	    }
6719 	    if (pcic_cbdoreset_during_poweron &&
6720 		(orig_cbctl & (CB_C_VCCMASK|CB_C_VPPMASK)) == 0) {
6721 		pcic_putb(pcic, socket, PCIC_INTERRUPT, iobits);
6722 	    }
6723 	    cmn_err(CE_WARN,
6724 		    "pcic socket %d: Power didn't get turned on/off!\n"
6725 		    "cbstev = 0x%x cbps = 0x%x cbctl 0x%x(0x%x) "
6726 		    "vcc %d vpp1 %d", socket, cbstev,
6727 		    pcic_getcb(pcic, CB_PRESENT_STATE),
6728 		    cbctl, orig_cbctl, sockp->pcs_vcc, sockp->pcs_vpp1);
6729 	    return (BAD_VCC);
6730 	}
6731 	return (SUCCESS);
6732 }
6733 
6734 static int	pcic_do_pprintf = 0;
6735 
6736 static void
6737 pcic_dump_debqueue(char *msg)
6738 {
6739 	struct debounce *debp = pcic_deb_queue;
6740 	clock_t lbolt;
6741 
6742 	(void) drv_getparm(LBOLT, &lbolt);
6743 	pcic_err(NULL, 6, debp ? "pcic debounce list (%s) lbolt 0x%x:\n" :
6744 	    "pcic debounce_list (%s) EMPTY lbolt 0x%x\n", msg, lbolt);
6745 	while (debp) {
6746 		pcic_err(NULL, 6, "%p: exp 0x%x next 0x%p id 0x%p\n",
6747 		    (void *) debp, (int)debp->expire, (void *) debp->next,
6748 		    debp->pcs->pcs_debounce_id);
6749 		debp = debp->next;
6750 	}
6751 }
6752 
6753 
6754 /* PRINTFLIKE3 */
6755 static void
6756 pcic_err(dev_info_t *dip, int level, const char *fmt, ...)
6757 {
6758 	if (pcic_debug && (level <= pcic_debug)) {
6759 		va_list adx;
6760 		int	instance;
6761 		char	buf[256];
6762 		const char	*name;
6763 #if !defined(PCIC_DEBUG)
6764 		int	ce;
6765 		char	qmark = 0;
6766 
6767 		if (level <= 3)
6768 			ce = CE_WARN;
6769 		else
6770 			ce = CE_CONT;
6771 		if (level == 4)
6772 			qmark = 1;
6773 #endif
6774 
6775 		if (dip) {
6776 			instance = ddi_get_instance(dip);
6777 			/* name = ddi_binding_name(dip); */
6778 			name = ddi_driver_name(dip);
6779 		} else {
6780 			instance = 0;
6781 			name = "";
6782 		}
6783 
6784 		va_start(adx, fmt);
6785 		(void) vsprintf(buf, fmt, adx);
6786 		va_end(adx);
6787 
6788 #if defined(PCIC_DEBUG)
6789 		if (pcic_do_pprintf) {
6790 			if (dip) {
6791 				if (instance >= 0)
6792 					prom_printf("%s(%d),0x%p: %s", name,
6793 					    instance, dip, buf);
6794 				else
6795 					prom_printf("%s,0x%p: %s",
6796 					    name, dip, buf);
6797 			} else
6798 				prom_printf(buf);
6799 		} else {
6800 			if (dip) {
6801 				if (instance >= 0)
6802 					cmn_err(CE_CONT, "%s(%d),0x%p: %s",
6803 					    name, instance, (void *) dip, buf);
6804 				else
6805 					cmn_err(CE_CONT, "%s,0x%p: %s",
6806 					    name, (void *) dip, buf);
6807 			} else
6808 				cmn_err(CE_CONT, buf);
6809 		}
6810 #else
6811 		if (dip)
6812 			cmn_err(ce, qmark ? "?%s%d: %s" : "%s%d: %s", name,
6813 			    instance, buf);
6814 		else
6815 			cmn_err(ce, qmark ? "?%s" : buf, buf);
6816 #endif
6817 	}
6818 }
6819 
6820 
6821 static void
6822 pcic_syshw_cardstate(syshw_t *item, void *arg)
6823 {
6824 	pcic_socket_t *pcs = (pcic_socket_t *)arg;
6825 
6826 	if (pcs->pcs_flags & PCS_CARD_PRESENT) {
6827 		item->state = B_TRUE;
6828 		if (pcs->pcs_flags & PCS_CARD_IS16BIT)
6829 			item->values[0] = 1;
6830 		else if (pcs->pcs_flags & PCS_CARD_ISCARDBUS)
6831 			item->values[0] = 2;
6832 		else
6833 			item->values[0] = 0;
6834 	} else {
6835 		item->state = B_FALSE;
6836 		item->values[0] = 0;
6837 	}
6838 }
6839 
6840 /*
6841  * Tadpole additional for the syshw interface used to control the
6842  * start/stop switch which is physically linked to the GPIO1 pin
6843  * on the 1250a.
6844  */
6845 
6846 #define	CLIENT_CALLED	0x8000000
6847 #define	NCE_EVENT_MASK	0xffff
6848 
6849 typedef struct _client {
6850 	pid_t	pid;		/* set by kernel */
6851 	int	flags;		/* NCE_REGISTER...  */
6852 	int	priority;	/* >100 unless root */
6853 	int	events;		/* pending event flags */
6854 	int	event_sig;	/* SIG... etc */
6855 	struct _client *next;	/* set by kernel */
6856 	struct _client *prev;	/* set by kernel */
6857 } client_data;
6858 
6859 static client_data	*cl_data;
6860 static int	n_clients;
6861 static kmutex_t	client_mtx, intr_mtx;
6862 
6863 static void	delete_client(int);
6864 
6865 #ifdef VOYAGER
6866 static uint32_t	runstop_sig;
6867 static ddi_softintr_t	softint_id;
6868 static uchar_t	softint_flag;
6869 static int	switch_debounce_time = 100;	/* in milliseconds */
6870 static timeout_id_t	switch_to_id;
6871 
6872 static syshw_t syshw_run_stop = {
6873 	    0, "Run/Stop", SH_SWITCH,
6874 	    SYSHW_CAN_SIGNAL_CHANGE|SYSHW_STATE_VALID,
6875 	    B_FALSE, { 0 } };
6876 
6877 static void
6878 syshw_get_run_stop(syshw_t *item, void *arg)
6879 {
6880 	pcicdev_t *pcic = (pcicdev_t *)arg;
6881 
6882 	if (ddi_get8(pcic->cfg_handle,
6883 	    pcic->cfgaddr + PCIC_GPIO1_REG) & PCIC_GPIO_DIN)
6884 		item->state = B_TRUE;
6885 	else
6886 		item->state = B_FALSE;
6887 }
6888 
6889 
6890 #endif
6891 
6892 static void
6893 syshw_attach(pcicdev_t *pcic)
6894 {
6895 	if (ddi_get_instance(pcic->dip) != 0)
6896 		return;
6897 
6898 #ifdef VOYAGER
6899 	if (pcic->pc_type == PCIC_TI_PCI1250) {
6900 
6901 		/*
6902 		 * Only setup run/stop on a Voyager.
6903 		 * This is currently defined as
6904 		 * a TI1250 on a SPARC architecture. May have to make this a
6905 		 * property definition in the future.
6906 		 */
6907 		if (ddi_add_softintr(pcic->dip,
6908 		    DDI_SOFTINT_LOW, &softint_id,
6909 		    NULL, NULL, syshw_intr,
6910 		    (caddr_t)pcic) == DDI_SUCCESS) {
6911 			runstop_sig = syshw_add2map(&syshw_run_stop,
6912 			    syshw_get_run_stop, pcic);
6913 			mutex_init(&intr_mtx, NULL, MUTEX_DRIVER,
6914 			    pcic->pc_pri);
6915 			ddi_put8(pcic->cfg_handle,
6916 			    pcic->cfgaddr + PCIC_GPIO1_REG,
6917 			    PCIC_GPIO_FINPUT | PCIC_GPIO_INTENBL |
6918 			    PCIC_GPIO_DELTA);
6919 		}
6920 	}
6921 #endif
6922 	mutex_init(&client_mtx, "syshw client", MUTEX_DRIVER, NULL);
6923 	(void) ddi_create_minor_node(pcic->dip, "syshw", S_IFCHR,
6924 	    SYSHW_MINOR, NULL, NULL);
6925 }
6926 
6927 static void
6928 syshw_detach(pcicdev_t *pcic)
6929 {
6930 #ifdef VOYAGER
6931 	if (pcic->pc_type == PCIC_TI_PCI1250) {
6932 		pcic_mutex_enter(&intr_mtx);
6933 
6934 		/*
6935 		 * Turn off this interrupt.
6936 		 */
6937 		ddi_put8(pcic->cfg_handle, pcic->cfgaddr + PCIC_GPIO1_REG,
6938 		    PCIC_GPIO_FINPUT);
6939 
6940 		if (switch_to_id)
6941 			(void) untimeout(switch_to_id);
6942 		switch_to_id = 0;
6943 		softint_flag = 0;
6944 
6945 		pcic_mutex_exit(&intr_mtx);
6946 		ddi_remove_softintr(softint_id);
6947 		mutex_destroy(&intr_mtx);
6948 	}
6949 #endif
6950 
6951 	ddi_remove_minor_node(pcic->dip, NULL);
6952 	mutex_destroy(&client_mtx);
6953 }
6954 
6955 static void
6956 syshw_resume(pcicdev_t *pcic)
6957 {
6958 #ifdef VOYAGER
6959 	if (pcic->pc_type == PCIC_TI_PCI1250) {
6960 		ddi_put8(pcic->cfg_handle, pcic->cfgaddr + PCIC_GPIO1_REG,
6961 		    PCIC_GPIO_FINPUT | PCIC_GPIO_INTENBL | PCIC_GPIO_DELTA);
6962 	}
6963 #else
6964 	_NOTE(ARGUNUSED(pcic))
6965 #endif
6966 }
6967 
6968 #ifdef VOYAGER
6969 static uint_t
6970 syshw_intr_hi(pcicdev_t *pcic)
6971 {
6972 	uchar_t regval;
6973 
6974 	if (pcic->pc_type != PCIC_TI_PCI1250)
6975 		return (DDI_INTR_UNCLAIMED);
6976 
6977 	regval = ddi_get8(pcic->cfg_handle, pcic->cfgaddr + PCIC_GPIO1_REG);
6978 	if (regval & PCIC_GPIO_DELTA) {
6979 		pcic_mutex_enter(&intr_mtx);
6980 		if (softint_flag == 0 && switch_to_id == 0) {
6981 			softint_flag = 1;
6982 			ddi_trigger_softintr(softint_id);
6983 		}
6984 		ddi_put8(pcic->cfg_handle, pcic->cfgaddr + PCIC_GPIO1_REG,
6985 		    regval);
6986 		pcic_mutex_exit(&intr_mtx);
6987 		return (DDI_INTR_CLAIMED);
6988 	}
6989 
6990 	return (DDI_INTR_UNCLAIMED);
6991 }
6992 
6993 /*
6994  * Don't deliver the signal until the debounce period has expired.
6995  * Unfortuately this means it end up as a three tier interrupt just
6996  * to indicate a bit change.
6997  */
6998 static void
6999 syshw_debounce_to(void *arg)
7000 {
7001 	_NOTE(ARGUNUSED(arg))
7002 
7003 	if (switch_to_id) {
7004 		pcic_mutex_enter(&intr_mtx);
7005 		switch_to_id = 0;
7006 		pcic_mutex_exit(&intr_mtx);
7007 		syshw_send_signal(runstop_sig);
7008 		return;
7009 	}
7010 }
7011 
7012 static uint_t
7013 syshw_intr(caddr_t arg)
7014 {
7015 	_NOTE(ARGUNUSED(arg))
7016 
7017 	if (softint_flag) {
7018 		pcic_mutex_enter(&intr_mtx);
7019 		softint_flag = 0;
7020 		if (!switch_to_id)
7021 			switch_to_id = timeout(syshw_debounce_to, arg,
7022 			    drv_usectohz(switch_debounce_time * 1000));
7023 		pcic_mutex_exit(&intr_mtx);
7024 		return (DDI_INTR_CLAIMED);
7025 	}
7026 	return (DDI_INTR_UNCLAIMED);
7027 }
7028 #endif
7029 
7030 /*
7031  * Send signals to the registered clients
7032  */
7033 static void
7034 syshw_send_signal(int events)
7035 {
7036 	client_data *ptr;
7037 	proc_t	*pr;
7038 	int	done_flag;
7039 
7040 	ptr = cl_data;
7041 	while (ptr != NULL) {
7042 		done_flag = CLIENT_CALLED;
7043 
7044 		if ((ptr->flags & events) &&
7045 		    (ptr->event_sig != 0) &&
7046 		    ((ptr->flags & done_flag) == 0)) {
7047 
7048 			/*
7049 			 * only call the process if:
7050 			 * it has not already received the nce signal
7051 			 * its signal was not zero (just in case)
7052 			 * and it is registered to receive this signal
7053 			 */
7054 			pcic_mutex_enter(&pidlock);
7055 			pr = prfind(ptr->pid);
7056 			pcic_mutex_exit(&pidlock);
7057 			if (pr == NULL) {
7058 				/*
7059 				 * This process has died,
7060 				 * so we free its memory and move on
7061 				 * start at the begining again:
7062 				 * a waste of cycles but it makes things easy..
7063 				 */
7064 				delete_client(ptr->pid);
7065 				ptr = cl_data;
7066 			} else {
7067 				ptr->events |= (events & ptr->flags &
7068 				    NCE_EVENT_MASK);
7069 				psignal(pr, ptr->event_sig);
7070 				ptr->flags |= done_flag;
7071 				ptr = ptr->next;
7072 			}
7073 		} else {
7074 			ptr = ptr->next;
7075 		}
7076 	}
7077 
7078 	ptr = cl_data;
7079 	while (ptr != NULL) {
7080 		ptr->flags &= ~done_flag;
7081 		ptr = ptr->next;
7082 	}
7083 }
7084 
7085 static int
7086 syshw_open(dev_t *dev, int flag, int otyp, cred_t *cred)
7087 {
7088 	_NOTE(ARGUNUSED(dev, flag, cred))
7089 
7090 	if (otyp != OTYP_CHR)
7091 		return (EINVAL);
7092 
7093 	return (0);
7094 }
7095 
7096 static int
7097 syshw_close(dev_t dev, int flag, int otyp, cred_t *cred)
7098 {
7099 	_NOTE(ARGUNUSED(dev, flag, otyp, cred))
7100 
7101 	return (0);
7102 }
7103 
7104 /*
7105  * Add a client to the list of interested processes
7106  */
7107 static void
7108 add_client(client_data *new)
7109 {
7110 	client_data * ptr;
7111 
7112 	n_clients++;
7113 	if (cl_data == NULL) {
7114 		cl_data = new;
7115 		return;
7116 	}
7117 
7118 	ptr = cl_data;
7119 	while ((ptr->next != NULL) && (ptr->priority <= new->priority))
7120 		ptr = ptr->next;
7121 
7122 	if (ptr == cl_data) {
7123 		/* at head of the list */
7124 		cl_data = new;
7125 		new->next = ptr;
7126 		new->prev = NULL;
7127 		if (ptr != NULL)
7128 			ptr->prev = new;
7129 	} else {
7130 		/* somewhere else in the list - insert after */
7131 		new->next = ptr->next;
7132 		ptr->next = new;
7133 		new->prev = ptr;
7134 		if (new->next != NULL)
7135 			(new->next)->prev = new;
7136 	}
7137 }
7138 
7139 /*
7140  * Locate a client data structure in the client list by looking for a PID match.
7141  */
7142 static client_data *
7143 locate_client(pid_t pid)
7144 {
7145 	client_data * ptr = cl_data;
7146 
7147 	while ((ptr != NULL) && (ptr->pid != pid))
7148 		ptr = ptr->next;
7149 
7150 	return (ptr);
7151 }
7152 
7153 /*
7154  * Remove a client record from the client list
7155  */
7156 static void
7157 delete_client(pid_t pid)
7158 {
7159 	client_data * ptr;
7160 
7161 	ptr = locate_client(pid);
7162 	if (ptr == NULL)
7163 		return;	/* hmmm!! */
7164 
7165 	n_clients--;
7166 
7167 	if (ptr == cl_data) {
7168 		/* remove the head of the list */
7169 		cl_data = ptr->next;
7170 	}
7171 	if (ptr->prev != NULL)
7172 		(ptr->prev)->next = ptr->next;
7173 	if (ptr->next != NULL)
7174 		(ptr->next)->prev = ptr->prev;
7175 
7176 	kmem_free(ptr, sizeof (client_data));
7177 }
7178 
7179 static void
7180 unregister_event_client()
7181 {
7182 	pcic_mutex_enter(&client_mtx);
7183 	delete_client(ddi_get_pid());
7184 	pcic_mutex_exit(&client_mtx);
7185 }
7186 
7187 static int
7188 register_event_client(client_data *u_client)
7189 {
7190 	int	error;
7191 	client_data * client;
7192 
7193 	pcic_mutex_enter(&client_mtx);
7194 	client = locate_client(ddi_get_pid());
7195 	if (client) {
7196 		/*
7197 		 * we are re-registering ourself
7198 		 * so we delete the previous entry
7199 		 */
7200 		delete_client(ddi_get_pid());
7201 	}
7202 
7203 	client = (client_data *)kmem_alloc(sizeof (client_data), KM_SLEEP);
7204 
7205 	if (client) {
7206 		client->pid = ddi_get_pid();
7207 		client->priority = u_client->priority;
7208 		client->flags = u_client->flags & NCE_EVENT_MASK;
7209 		client->events = 0;
7210 		client->event_sig = u_client->event_sig;
7211 		client->next = NULL;
7212 		client->prev = NULL;
7213 		add_client(client);
7214 		error = 0;
7215 	} else
7216 		error = EIO;
7217 
7218 	pcic_mutex_exit(&client_mtx);
7219 	return (error);
7220 }
7221 
7222 /*
7223  * Read the currently pending event flags for the process in question
7224  */
7225 static int
7226 check_events_pending(caddr_t data)
7227 {
7228 	client_data * client;
7229 	int	error = 0;
7230 
7231 	pcic_mutex_enter(&client_mtx);
7232 	client = locate_client(ddi_get_pid());
7233 	if (client) {
7234 		if (copyout((caddr_t)&client->events, data, sizeof (int)))
7235 			error = EFAULT;
7236 		else
7237 			client->events = 0;
7238 	} else
7239 		error = EINVAL;
7240 
7241 	pcic_mutex_exit(&client_mtx);
7242 	return (error);
7243 }
7244 
7245 
7246 #define	MAXITEMS	8
7247 static syshw_t *syshw_map[MAXITEMS];
7248 static void	(*syshw_getfuncs[MAXITEMS])(syshw_t *, void *);
7249 static void	*syshw_getfunc_args[MAXITEMS];
7250 static int	nsyshw_items = 0;
7251 #define	NSYSHW_ITEMS	nsyshw_items
7252 
7253 static uint32_t
7254 syshw_add2map(syshw_t *item, void (*getfunc)(syshw_t *, void *), void *getarg)
7255 {
7256 	uint32_t rval = (1 << nsyshw_items);
7257 	if (nsyshw_items == MAXITEMS)
7258 		return (0);
7259 	item->hw_id = nsyshw_items;
7260 	syshw_map[nsyshw_items] = item;
7261 	syshw_getfuncs[nsyshw_items] = getfunc;
7262 	syshw_getfunc_args[nsyshw_items] = getarg;
7263 	nsyshw_items++;
7264 	return (rval);
7265 }
7266 
7267 static int
7268 syshw_ioctl(dev_t dev, int cmd, intptr_t ioctldata, int mode,
7269 cred_t *cred, int *rval)
7270 {
7271 	caddr_t data = (caddr_t)ioctldata;
7272 	syshw_t sh;
7273 	hwev_t hwev;
7274 	client_data dummy_client;
7275 	int	rc = 0, i;
7276 
7277 	_NOTE(ARGUNUSED(dev, mode, cred, rval))
7278 
7279 	switch (cmd) {
7280 	default:
7281 		rc = EINVAL;
7282 		break;
7283 
7284 	case SYSHW_GET_ITEM:
7285 	case SYSHW_GET_ITEM_MAXVALUES:
7286 		if (copyin(data, (caddr_t)&sh, sizeof (sh))) {
7287 			rc = EFAULT;
7288 			break;
7289 		}
7290 
7291 		if (sh.hw_id >= NSYSHW_ITEMS) {
7292 			rc = EINVAL;
7293 			break;
7294 		}
7295 
7296 		sh = *syshw_map[sh.hw_id];
7297 		if (!sh.id_string[0]) {
7298 			rc = ENOTTY;
7299 			break;
7300 		}
7301 		if (cmd == SYSHW_GET_ITEM) {
7302 			if (syshw_getfuncs[sh.hw_id])
7303 				syshw_getfuncs[sh.hw_id](&sh,
7304 				    syshw_getfunc_args[sh.hw_id]);
7305 			else
7306 				rc = ENOTTY;
7307 		}
7308 
7309 		if (copyout((caddr_t)&sh, data, sizeof (sh))) {
7310 			rc = EFAULT;
7311 			break;
7312 		}
7313 		break;
7314 
7315 	case SYSHW_SET_ITEM:
7316 		if (copyin(data, (caddr_t)&sh, sizeof (sh))) {
7317 			rc = EFAULT;
7318 			break;
7319 		}
7320 
7321 		if (sh.hw_id >= NSYSHW_ITEMS ||
7322 		    !syshw_map[sh.hw_id]->id_string[0] ||
7323 		    !(syshw_map[sh.hw_id]->capabilities &
7324 		    (SYSHW_STATE_MODIFY | SYSHW_VAL0_MODIFY |
7325 		    SYSHW_VAL1_MODIFY | SYSHW_VAL2_MODIFY |
7326 		    SYSHW_VAL3_MODIFY))) {
7327 			rc = EINVAL;
7328 			break;
7329 		}
7330 
7331 		switch (sh.hw_id) {
7332 		default:
7333 			rc = EINVAL;
7334 			break;
7335 		}
7336 		break;
7337 
7338 	case SYSHW_EVREG:
7339 		if (copyin(data, (caddr_t)&hwev, sizeof (hwev))) {
7340 			rc = EFAULT;
7341 			break;
7342 		}
7343 
7344 		for (i = 0; i < NSYSHW_ITEMS; i++) {
7345 			if (hwev.events & (1 << i) &&
7346 			    !(syshw_map[i]->capabilities &
7347 			    SYSHW_CAN_SIGNAL_CHANGE)) {
7348 				rc = EINVAL;
7349 				break;
7350 			}
7351 		}
7352 		if (hwev.event_sig != SIGUSR1 && hwev.event_sig != SIGUSR2)
7353 			rc = EINVAL;
7354 
7355 		if (!rc) {
7356 			dummy_client.priority = 100;
7357 			dummy_client.flags = hwev.events;
7358 			dummy_client.event_sig = hwev.event_sig;
7359 			rc = register_event_client(&dummy_client);
7360 		}
7361 		break;
7362 
7363 	case SYSHW_EVUNREG:
7364 		unregister_event_client();
7365 		break;
7366 
7367 	case SYSHW_CHKEV:
7368 		rc = check_events_pending(data);
7369 		break;
7370 	}
7371 	return (rc);
7372 }
7373