xref: /titanic_51/usr/src/uts/common/sys/scsi/conf/autoconf.h (revision 4c06356b0f0fffb4fc1b6eccc8e5d8e2254a84d6)

/*
 * CDDL HEADER START
 *
 * The contents of this file are subject to the terms of the
 * Common Development and Distribution License (the "License").
 * You may not use this file except in compliance with the License.
 *
 * You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE
 * or http://www.opensolaris.org/os/licensing.
 * See the License for the specific language governing permissions
 * and limitations under the License.
 *
 * When distributing Covered Code, include this CDDL HEADER in each
 * file and include the License file at usr/src/OPENSOLARIS.LICENSE.
 * If applicable, add the following below this CDDL HEADER, with the
 * fields enclosed by brackets "[]" replaced with your own identifying
 * information: Portions Copyright [yyyy] [name of copyright owner]
 *
 * CDDL HEADER END
 */
/*
 * Copyright 2009 Sun Microsystems, Inc.  All rights reserved.
 * Use is subject to license terms.
 */

#ifndef _SYS_SCSI_CONF_AUTOCONF_H
#define	_SYS_SCSI_CONF_AUTOCONF_H

#ifdef	__cplusplus
extern "C" {
#endif

/*
 * SCSI subsystem scsi_options
 */

/*
 * Following are for debugging purposes (few Sun drivers support this)
 */
#define	SCSI_DEBUG_TGT	0x1	/* debug statements in target drivers */
#define	SCSI_DEBUG_LIB	0x2	/* debug statements in library */
#define	SCSI_DEBUG_HA	0x4	/* debug statements in host adapters */

/*
 * Following are applicable to all interconnects
 */
#define	SCSI_OPTIONS_LINK	0x10	/* Global linked commands */
#define	SCSI_OPTIONS_TAG	0x80	/* Global tagged command support */

/*
 * Following are for parallel SCSI only
 */
#define	SCSI_OPTIONS_DR		0x8	/* Global disconnect/reconnect	*/
#define	SCSI_OPTIONS_SYNC	0x20	/* Global synchronous xfer capability */
#define	SCSI_OPTIONS_PARITY	0x40	/* Global parity support */
#define	SCSI_OPTIONS_FAST	0x100	/* Global FAST scsi support */
#define	SCSI_OPTIONS_WIDE	0x200	/* Global WIDE scsi support */
#define	SCSI_OPTIONS_FAST20	0x400	/* Global FAST20 scsi support */
#define	SCSI_OPTIONS_FAST40	0x800	/* Global FAST40 scsi support */
#define	SCSI_OPTIONS_FAST80	0x1000	/* Global FAST80 scsi support */
#define	SCSI_OPTIONS_FAST160	0x2000	/* Global FAST160 scsi support */
#define	SCSI_OPTIONS_FAST320	0x4000	/* Global FAST320 scsi support */

/*
 * The following 3 bits are for being able to limit the max. number of LUNs
 * a nexus driver will allow -- "default" means that the adapter will
 * continue its default behavior.
 */
#define	SCSI_OPTIONS_NLUNS_MASK		(0x70000)

#define	SCSI_OPTIONS_NLUNS_DEFAULT	0x00000
#define	SCSI_OPTIONS_NLUNS_1		0x10000
#define	SCSI_OPTIONS_NLUNS_8		0x20000
#define	SCSI_OPTIONS_NLUNS_16		0x30000
#define	SCSI_OPTIONS_NLUNS_32		0x40000
#define	SCSI_OPTIONS_NLUNS_64		0x50000
#define	SCSI_OPTIONS_NLUNS_128		0x60000
#define	SCSI_OPTIONS_NLUNS_256		0x70000

#define	SCSI_OPTIONS_NLUNS(n)		((n) & SCSI_OPTIONS_NLUNS_MASK)

#define	SCSI_OPTIONS_QAS	0x100000 /* Global Quick Arbitration Select */

/*
 * SCSI autoconfiguration definitions.
 *
 * The library routine scsi_slave() is provided as a service to target
 * driver to check for existence  and readiness of a SCSI device. It is
 * defined as:
 *
 *	int scsi_slave(struct scsi_device *devp, int (*callback)(void))
 *
 * where devp is the scsi_device structure passed to the target driver
 * at probe time, and where callback declares whether scsi_slave() can
 * sleep awaiting resources or must return an error if it cannot get
 * resources (callback == SLEEP_FUNC implies that scsi_slave()
 * can sleep - although this
 * does not fully guarantee that resources will become available as
 * some are allocated from the iopbmap which may just be completely
 * full).  The user call also supplies a callback function or NULL_FUNC.
 * In the process of determining the existence of a SCSI device,
 * scsi_slave will allocate space for the sd_inq field of the scsi_device
 * pointed to by devp (if it is non-zero upon entry).
 *
 * scsi_slave() attempts to follow this sequence in order to determine
 * the existence of a SCSI device:
 *
 *	Attempt to send 2 TEST UNIT READY commands to the device.
 *
 *		If that gets a check condition, run a non-extended
 *		REQUEST SENSE command. Ignore the results of it, as
 *		a the non-extended sense information contains only
 *		Vendor Unique error codes (the idea is that during
 *		probe time the nearly invariant first command to a
 *		device will get a Check Condition, and the real reason
 *		is that the device wants to tell you that a SCSI bus
 *		reset just occurred.
 *
 *	Attempt to allocate an inquiry buffer and
 *	run an INQUIRY command (with response data format 0 set).
 *
 *		If that gets a check condition, run another
 *		non-extended REQUEST SENSE command.
 *
 * The library routine scsi_probe() is provided as a service to target
 * driver to check for bare-bones existence of a SCSI device. It is
 * defined as:
 *
 *	int scsi_probe(struct scsi_device *devp, int (*callback)(void))
 *
 * scsi_probe() only executes an inquiry.
 *
 * Both functions return one of the integer values as defined below:
 */
#define	SCSIPROBE_EXISTS	0	/* device exists, inquiry data valid */
#define	SCSIPROBE_NONCCS	1	/* device exists, no inquiry data */
#define	SCSIPROBE_NORESP	2	/* device didn't respond */
#define	SCSIPROBE_NOMEM		3	/* no space available for structures */
#define	SCSIPROBE_FAILURE	4	/* polled cmnd failure- unspecified */
#define	SCSIPROBE_BUSY		5	/* device was busy */
#define	SCSIPROBE_NOMEM_CB	6	/* no space, callback queued */
#define	SCSIPROBE_ASCII					\
	{"EXISTS", "NONCCS", "NORESP", "NOMEM",		\
	"FAILURE", "BUSY", "NOMEM_CB", NULL}

/*
 * default value for scsi_reset_delay
 */
#define	SCSI_DEFAULT_RESET_DELAY	3000

/*
 * default value for scsi_selection_timeout
 */
#define	SCSI_DEFAULT_SELECTION_TIMEOUT	250

/*
 * SCSI subsystem scsi_enumeration options.
 *
 * Knob for SPI (SCSI Parallel Intrconnect) enumeration. Unless an HBA defines
 * it's own tran_bus_config, SPI enumeration is used. The "scsi_enumeration"
 * knob determines how SPI enumeration is performed.
 *
 * The global variable "scsi_enumeration" is used as the default value of the
 * "scsi-enumeration" property. In addition to enabling/disabling enumeration
 * (bit 0), target and lun threading can be specified.  Having things
 * multi-threaded does not guarantee reduce configuration time, however when
 * the bus is marginal multi-threading can substaintaly reduce configuration
 * time because targets negotiate to stable transfer speeds in parallel - so
 * all targets have stabalized by the time the sequential attach(9E) operations
 * begin.  Running multi-threaded also helps verification of framework and HBA
 * locking: a BUS_CONFIG_ALL is equivalent to every target and lun combination
 * getting a BUS_CONFIG_ONE from a separate thread at the same time.  A disable
 * mechanism is provided to accomidate buggy HBAs (set scsi-enumeration=7
 * driver.conf). Values are:
 *
 *	0	driver.conf enumeration
 *	1	dynamic enumeration with target and lun multi-threading.
 *	3	dynamic enumeration with lun multi-threading disabled.
 *	5	dynamic enumeration with target multi-threading disabled;
 *	7	dynamic enumeration with target/lun multi-threading disabled.
 */
#define	SCSI_ENUMERATION_ENABLE			0x1
#define	SCSI_ENUMERATION_MT_LUN_DISABLE		0x2
#define	SCSI_ENUMERATION_MT_TARGET_DISABLE	0x4

#ifdef	_KERNEL
/*
 * Global SCSI config variables / options
 */
extern int		scsi_options;
extern int		scsi_enumeration;
extern unsigned int	scsi_reset_delay;	/* specified in milli seconds */
extern int		scsi_tag_age_limit;
extern int		scsi_watchdog_tick;
extern int		scsi_selection_timeout;	/* specified in milli seconds */
extern int		scsi_host_id;
extern int		scsi_fm_capable;
#endif	/* _KERNEL */

#ifdef	__cplusplus
}
#endif

#endif	/* _SYS_SCSI_CONF_AUTOCONF_H */