1# 2# This file is provided under a CDDLv1 license. When using or 3# redistributing this file, you may do so under this license. 4# In redistributing this file this license must be included 5# and no other modification of this header file is permitted. 6# 7# CDDL LICENSE SUMMARY 8# 9# Copyright(c) 1999 - 2009 Intel Corporation. All rights reserved. 10# 11# The contents of this file are subject to the terms of Version 12# 1.0 of the Common Development and Distribution License (the "License"). 13# 14# You should have received a copy of the License with this software. 15# You can obtain a copy of the License at 16# http://www.opensolaris.org/os/licensing. 17# See the License for the specific language governing permissions 18# and limitations under the License. 19# 20# 21# Copyright 2009 Sun Microsystems, Inc. All rights reserved. 22# Use is subject to license terms of the CDDLv1. 23# 24# 25# Driver.conf file for Intel e1000g Gigabit Ethernet Adapter 26# 27ForceSpeedDuplex=7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7; 28 # This will force Speed and Duplex for following settings for a typical instance. 29 # 1 will set the 10 Mbps speed and Half Duplex mode. 30 # 2 will set the 10 Mbps speed and Full Duplex mode. 31 # 3 will set the 100 Mbps speed and half Duplex mode. 32 # 4 will set the 100 Mbps speed and Full Duplex mode. 33 # 7 will let adapter autonegotiate. 34AutoNegAdvertised=0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0; 35 # This parameter determines the speed/duplex options that will be 36 # advertised during auto-negotiation. This is a bitmap with the 37 # following settings. 38 # Bit | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 39 # Setting| N/A | N/A | 1000F | N/A | 100F | 100H | 10F | 10H 40 # 41 # For example: 42 # To advertise 10 Half only AutoNegAdvertised = 1 43 # To advertise 10 Full only AutoNegAdvertised = 2 44 # To advertise 10 Half/Full AutoNegAdvertised = 3 45 # To advertise 100 Half only AutoNegAdvertised = 4 46 # To advertise 100 Full only AutoNegAdvertised = 8 47 # To advertise 100 Half/Full AutoNegAdvertised = 12 48 # To advertise 1000 Full only AutoNegAdvertised = 32 49 # To advertise all speeds AutoNegAdvertised = 47 50MaxFrameSize=0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0; 51 # 0 is for normal ethernet frames. 52 # 1 is for upto 4k size frames. 53 # 2 is for upto 8k size frames. 54 # 3 is for upto 16k size frames. 55 # 56 # These are maximum frame limits, not the ethernet payload size 57 # (usually called MTU). Your actual ethernet MTU is determined by frame 58 # size limit and protocol stack configuration (please refer to ndd 59 # command man pages) 60 # 61 # For Jumbo Frame Support (9k ethernet packet) use 3 (upto 16k size 62 # frames). On PCH adapter type (82577 and 82578) you can configure up 63 # to 4k size frames. The 4k size is only allowed at 1gig speed, so if 64 # you select 4k frames size, you cannot force or autonegotiate the 65 # 10/100 speed options. 66FlowControl=3,3,3,3,3,3,3,3,3,3,3,3,3,3,3,3; 67 # 0: Flow control is completely disabled 68 # 1: Rx flow control is enabled (we can receive pause frames 69 # but not send pause frames). 70 # 2: Tx flow control is enabled (we can send pause frames 71 # but we do not receiving pause frames). 72 # 3: Both Rx and TX flow control (symmetric) is enabled. 73 # 4: No software override. The flow control configuration 74 # in the EEPROM is used. 75TbiCompatibilityEnable=1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1; 76 # 1 turns it on and 0 turns it off. 77 # Some switches as Cisco 6500/Foundary still operate in TBI mode. 78 # This setting will fix the problems seen with odd byte packets. 79 # This setting is valid only for 82543GC based copper adapters. 80SetMasterSlave=0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0; 81 # 0 sets to hardware default 82 # 1 forces master 83 # 2 forces slave 84 # 3 forces auto 85 # This setting controls the PHY master/slave setting. Manually forcing 86 # master or slave can help reduce time to link with some switches 87 # (Planex 08TX and IO Data switches). It is recommended that this 88 # setting remain at the hardware default. 89