1# 2# This file is provided under a CDDLv1 license. When using or 3# redistributing this file, you may do so under this license. 4# In redistributing this file this license must be included 5# and no other modification of this header file is permitted. 6# 7# CDDL LICENSE SUMMARY 8# 9# Copyright(c) 1999 - 2007 Intel Corporation. All rights reserved. 10# 11# The contents of this file are subject to the terms of Version 12# 1.0 of the Common Development and Distribution License (the "License"). 13# 14# You should have received a copy of the License with this software. 15# You can obtain a copy of the License at 16# http://www.opensolaris.org/os/licensing. 17# See the License for the specific language governing permissions 18# and limitations under the License. 19# 20# 21# Copyright 2007 Sun Microsystems, Inc. All rights reserved. 22# Use is subject to license terms of the CDDLv1. 23# 24# 25# ident "%Z%%M% %I% %E% SMI" 26# 27# Driver.conf file for Intel e1000g Gigabit Ethernet Adapter 28# 29ForceSpeedDuplex=7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7; 30 # This will force Speed and Duplex for following settings for a typical instance. 31 # 1 will set the 10 Mbps speed and Half Duplex mode. 32 # 2 will set the 10 Mbps speed and Full Duplex mode. 33 # 3 will set the 100 Mbps speed and half Duplex mode. 34 # 4 will set the 100 Mbps speed and Full Duplex mode. 35 # 7 will let adapter autonegotiate. 36AutoNegAdvertised=0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0; 37 # This parameter determines the speed/duplex options that will be 38 # advertised during auto-negotiation. This is a bitmap with the 39 # following settings. 40 # Bit | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 41 # Setting| N/A | N/A | 1000F | N/A | 100F | 100H | 10F | 10H 42 # 43 # For example: 44 # To advertise 10 Half only AutoNegAdvertised = 1 45 # To advertise 10 Full only AutoNegAdvertised = 2 46 # To advertise 10 Half/Full AutoNegAdvertised = 3 47 # To advertise 100 Half only AutoNegAdvertised = 4 48 # To advertise 100 Full only AutoNegAdvertised = 8 49 # To advertise 100 Half/Full AutoNegAdvertised = 12 50 # To advertise 1000 Full only AutoNegAdvertised = 32 51 # To advertise all speeds AutoNegAdvertised = 47 52MaxFrameSize=0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0; 53 # 0 is for normal ethernet frames. 54 # 1 is for upto 4k size frames. 55 # 2 is for upto 8k size frames. 56 # 3 is for upto 16k size frames. 57 # These are maximum frame limits, not the actual ethernet frame 58 # size. Your actual ethernet frame size would be determined by 59 # protocol stack configuration (please refer to ndd command man pages) 60 # For Jumbo Frame Support (9k ethernet packet) 61 # use 3 (upto 16k size frames) 62FlowControl=3,3,3,3,3,3,3,3,3,3,3,3,3,3,3,3; 63 # 0: Flow control is completely disabled 64 # 1: Rx flow control is enabled (we can receive pause frames 65 # but not send pause frames). 66 # 2: Tx flow control is enabled (we can send pause frames 67 # but we do not receiving pause frames). 68 # 3: Both Rx and TX flow control (symmetric) is enabled. 69 # 4: No software override. The flow control configuration 70 # in the EEPROM is used. 71TbiCompatibilityEnable=1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1; 72 # 1 turns it on and 0 turns it off. 73 # Some switches as Cisco 6500/Foundary still operate in TBI mode. 74 # This setting will fix the problems seen with odd byte packets. 75 # This setting is valid only for 82543GC based copper adapters. 76SetMasterSlave=0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0; 77 # 0 sets to hardware default 78 # 1 forces master 79 # 2 forces slave 80 # 3 forces auto 81 # This setting controls the PHY master/slave setting. Manually forcing 82 # master or slave can help reduce time to link with some switches 83 # (Planex 08TX and IO Data switches). It is recommended that this 84 # setting remain at the hardware default. 85