Copyright (c) 2001, The IEEE and The Open Group. All Rights Reserved. Portions Copyright (c) 2004, Sun Microsystems, Inc. All Rights Reserved.
Sun Microsystems, Inc. gratefully acknowledges The Open Group for permission to reproduce portions of its copyrighted documentation. Original documentation from The Open Group can be obtained online at
http://www.opengroup.org/bookstore/.
The Institute of Electrical and Electronics Engineers and The Open Group, have given us permission to reprint portions of their documentation. In the following statement, the phrase "this text" refers to portions of the system documentation. Portions of this text are reprinted and reproduced in electronic form in the Sun OS Reference Manual, from IEEE Std 1003.1, 2004 Edition, Standard for Information Technology -- Portable Operating System Interface (POSIX), The Open Group Base Specifications Issue 6, Copyright (C) 2001-2004 by the Institute of Electrical and Electronics Engineers, Inc and The Open Group. In the event of any discrepancy between these versions and the original IEEE and The Open Group Standard, the original IEEE and The Open Group Standard is the referee document. The original Standard can be obtained online at http://www.opengroup.org/unix/online.html.
This notice shall appear on any product containing this material.
The contents of this file are subject to the terms of the Common Development and Distribution License (the "License"). You may not use this file except in compliance with the License.
You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE or http://www.opensolaris.org/os/licensing. See the License for the specific language governing permissions and limitations under the License.
When distributing Covered Code, include this CDDL HEADER in each file and include the License file at usr/src/OPENSOLARIS.LICENSE. If applicable, add the following below this CDDL HEADER, with the fields enclosed by brackets "[]" replaced with your own identifying information: Portions Copyright [yyyy] [name of copyright owner]
#include <termios.h>
The <termios.h> header contains the definitions used by the terminal I/O interfaces. See termios(3C) and termio(7I) for an overview of the terminal interface.
The following data types are defined through typedef: cc_t
used for terminal special characters
used for terminal baud rates
used for terminal modes
The above types are all unsigned integer types.
The implementation supports one or more programming environments in which the widths of cc_t, speed_t, and tcflag_t are no greater than the width of type long. The names of these programming environments can be obtained using the confstr(3C) function or the getconf(1) utility.
The termios structure is defined and includes the following members:
tcflag_t c_iflag /* input modes */ tcflag_t c_oflag /* output modes */ tcflag_t c_cflag /* control modes */ tcflag_t c_lflag /* local modes */ cc_t c_cc[NCCS] /* control characters */
A definition is provided for: NCCS
size of the array c_cc for control characters
The following subscript names for the array c_cc are defined:
| Subscript UsageCanonical Mode Subscript UsageNon-Canonical Mode Description |
| VEOF EOF character |
| VEOL EOL character |
| VERASE ERASE character |
| VINTR VINTR INTR character |
| VKILL KILL character |
| VMIN MIN value |
| VQUIT VQUIT QUIT character |
| VSTART VSTART START character |
| VSTOP VSTOP STOP character |
| VSUSP VSUSP SUSP character |
| VTIME TIME value |
| VSTATUS STATUS character |
The subscript values are unique, except that the VMIN and VTIME subscripts can have the same values as the VEOF and VEOL subscripts, respectively.
The header file provides the flags described below.
The c_iflag field describes the basic terminal input control: BRKINT
Signal interrupt on break.
Map CR to NL on input.
Ignore break condition.
Ignore CR.
Ignore characters with parity errors.
Map NL to CR on input.
Enable input parity check.
Strip character.
Enable any character to restart output.
Mark parity errors.
The c_oflag field specifies the system treatment of output: OPOST
Post-process output.
Map NL to CR-NL on output.
Map CR to NL on output.
No CR output at column 0.
NL performs CR function.
Use fill characters for delay.
Select newline delays: NL0
newline type 0
newline type 1
Select carriage-return delays: CR0
carriage-return delay type 0
carriage-return delay type 1
carriage-return delay type 2
carriage-return delay type 3
Select horizontal-tab delays: TAB0
horizontal-tab delay type 0
horizontal-tab delay type 1
horizontal-tab delay type 2
expand tabs to spaces
Select backspace delays: BS0
backspace-delay type 0
backspace-delay type 1
Select vertical-tab delays: VT0
vertical-tab delay type 0
vertical-tab delay type 1
Select form-feed delays: FF0
form-feed delay type 0
form-feed delay type 1
The input and output baud rates are stored in the termios structure. These are the valid values for objects of type speed_ t. The following values are defined, but not all baud rates need be supported by the underlying hardware. B0
Hang up
50 baud
75 baud
110 baud
134.5 baud
150 baud
200 baud
300 baud
600 baud
1 200 baud
1 800 baud
2 400 baud
4 800 baud
9 600 baud
19 200 baud
38 400 baud
The c_cflag field describes the hardware control of the terminal; not all values specified are required to be supported by the underlying hardware: CSIZE
Character size: CS5
5 bits
6 bits
7 bits
8 bits
Send two stop bits, else one.
Enable receiver.
Parity enable.
Odd parity, else even.
Hang up on last close.
Ignore modem status lines.
The implementation supports the functionality associated with the symbols CS7, CS8, CSTOPB, PARODD, and PARENB.
The c_lflag field of the argument structure is used to control various terminal functions: ECHO
Enable echo.
Echo erase character as error-correcting backspace.
Echo KILL.
Echo NL.
Canonical input (erase and kill processing).
Enable extended input character processing.
Enable signals.
Disable flush after interrupt or quit.
Send SIGTTOU for background output.
The following symbolic constants for use with tcsetattr() are defined: TCSANOW
Change attributes immediately.
Change attributes when output has drained.
Change attributes when output has drained; also flush pending input.
The following symbolic constants for use with tcflush() are defined: TCIFLUSH
Flush pending input.
Flush both pending input and untransmitted output.
Flush untransmitted output.
The following symbolic constants for use with tcflow() are defined: TCIOFF
Transmit a STOP character, intended to suspend input data.
Transmit a START character, intended to restart input data.
Suspend output.
Restart output.
See attributes(5) for descriptions of the following attributes:
| ATTRIBUTE TYPE ATTRIBUTE VALUE |
| Interface Stability Standard |
getconf(1), cfgetispeed(3C), cfsetispeed(3C), confstr(3C), tcdrain(3C), tcflow(3C), tcflush(3C), tcgetattr(3C), tcgetsid(3C), tcsendbreak(3C), tcsetattr(3C), attributes(5), standards(5)