1 /* 2 * CDDL HEADER START 3 * 4 * The contents of this file are subject to the terms of the 5 * Common Development and Distribution License (the "License"). 6 * You may not use this file except in compliance with the License. 7 * 8 * You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE 9 * or http://www.opensolaris.org/os/licensing. 10 * See the License for the specific language governing permissions 11 * and limitations under the License. 12 * 13 * When distributing Covered Code, include this CDDL HEADER in each 14 * file and include the License file at usr/src/OPENSOLARIS.LICENSE. 15 * If applicable, add the following below this CDDL HEADER, with the 16 * fields enclosed by brackets "[]" replaced with your own identifying 17 * information: Portions Copyright [yyyy] [name of copyright owner] 18 * 19 * CDDL HEADER END 20 */ 21 22 /* 23 * Copyright 2007 Sun Microsystems, Inc. All rights reserved. 24 * Use is subject to license terms. 25 */ 26 27 #pragma ident "%Z%%M% %I% %E% SMI" 28 29 #include <sys/time.h> 30 #include <sys/cpuvar.h> 31 #include <sys/dditypes.h> 32 #include <sys/ddipropdefs.h> 33 #include <sys/ddi_impldefs.h> 34 #include <sys/sunddi.h> 35 #include <sys/esunddi.h> 36 #include <sys/sunndi.h> 37 #include <sys/platform_module.h> 38 #include <sys/errno.h> 39 #include <sys/conf.h> 40 #include <sys/modctl.h> 41 #include <sys/promif.h> 42 #include <sys/promimpl.h> 43 #include <sys/prom_plat.h> 44 #include <sys/cmn_err.h> 45 #include <sys/sysmacros.h> 46 #include <sys/mem_cage.h> 47 #include <sys/kobj.h> 48 #include <sys/utsname.h> 49 #include <sys/cpu_sgnblk_defs.h> 50 #include <sys/atomic.h> 51 #include <sys/kdi_impl.h> 52 53 #include <sys/sgsbbc.h> 54 #include <sys/sgsbbc_iosram.h> 55 #include <sys/sgsbbc_iosram_priv.h> 56 #include <sys/sgsbbc_mailbox.h> 57 #include <sys/sgsgn.h> 58 #include <sys/serengeti.h> 59 #include <sys/sgfrutypes.h> 60 #include <sys/machsystm.h> 61 #include <sys/sbd_ioctl.h> 62 #include <sys/sbd.h> 63 #include <sys/sbdp_mem.h> 64 #include <sys/sgcn.h> 65 66 #include <sys/memnode.h> 67 #include <vm/vm_dep.h> 68 #include <vm/page.h> 69 70 #include <sys/cheetahregs.h> 71 #include <sys/plat_ecc_unum.h> 72 #include <sys/plat_ecc_dimm.h> 73 74 #include <sys/lgrp.h> 75 76 static int sg_debug = 0; 77 78 #ifdef DEBUG 79 #define DCMNERR if (sg_debug) cmn_err 80 #else 81 #define DCMNERR 82 #endif 83 84 int (*p2get_mem_unum)(int, uint64_t, char *, int, int *); 85 86 /* local functions */ 87 static void cpu_sgn_update(ushort_t sgn, uchar_t state, 88 uchar_t sub_state, int cpuid); 89 90 91 /* 92 * Local data. 93 * 94 * iosram_write_ptr is a pointer to iosram_write(). Because of 95 * kernel dynamic linking, we can't get to the function by name, 96 * but we can look up its address, and store it in this variable 97 * instead. 98 * 99 * We include the extern for iosram_write() here not because we call 100 * it, but to force compilation errors if its prototype doesn't 101 * match the prototype of iosram_write_ptr. 102 * 103 * The same issues apply to iosram_read() and iosram_read_ptr. 104 */ 105 /*CSTYLED*/ 106 extern int iosram_write (int, uint32_t, caddr_t, uint32_t); 107 static int (*iosram_write_ptr)(int, uint32_t, caddr_t, uint32_t) = NULL; 108 /*CSTYLED*/ 109 extern int iosram_read (int, uint32_t, caddr_t, uint32_t); 110 static int (*iosram_read_ptr)(int, uint32_t, caddr_t, uint32_t) = NULL; 111 112 113 /* 114 * Variable to indicate if the date should be obtained from the SC or not. 115 */ 116 int todsg_use_sc = FALSE; /* set the false at the beginning */ 117 118 /* 119 * Preallocation of spare tsb's for DR 120 * 121 * We don't allocate spares for Wildcat since TSBs should come 122 * out of memory local to the node. 123 */ 124 #define IOMMU_PER_SCHIZO 2 125 int serengeti_tsb_spares = (SG_MAX_IO_BDS * SG_SCHIZO_PER_IO_BD * 126 IOMMU_PER_SCHIZO); 127 128 /* 129 * sg_max_ncpus is the maximum number of CPUs supported on lw8. 130 * sg_max_ncpus is set to be smaller than NCPU to reduce the amount of 131 * memory the logs take up until we have a dynamic log memory allocation 132 * solution. 133 */ 134 int sg_max_ncpus = (12 * 2); /* (max # of processors * # of cores/proc) */ 135 136 /* 137 * variables to control mailbox message timeouts. 138 * These can be patched via /etc/system or mdb. 139 */ 140 int sbbc_mbox_default_timeout = MBOX_DEFAULT_TIMEOUT; 141 int sbbc_mbox_min_timeout = MBOX_MIN_TIMEOUT; 142 143 /* cached 'chosen' node_id */ 144 pnode_t chosen_nodeid = (pnode_t)0; 145 146 /* 147 * Table that maps memory slices to a specific memnode. 148 */ 149 int slice_to_memnode[SG_MAX_SLICE]; 150 151 /* 152 * We define and use LW8_MAX_CPU_BDS here instead of SG_MAX_CPU_BDS 153 * since a LW8 machine will never have a CPU/Mem board #5 (SB5). 154 * A LW8 machine can only have a maximum of three CPU/Mem boards, but 155 * the board numbers assigned are 0, 2, and 4. LW8_MAX_CPU_BDS is 156 * defined to be 5 since the entries in the domain_dimm_sids array 157 * are keyed by board number. Not perfect but some wasted space 158 * is avoided. 159 */ 160 #define LW8_MAX_CPU_BDS 5 161 162 plat_dimm_sid_board_t domain_dimm_sids[LW8_MAX_CPU_BDS]; 163 164 int 165 set_platform_tsb_spares() 166 { 167 return (MIN(serengeti_tsb_spares, MAX_UPA)); 168 } 169 170 #pragma weak mmu_init_large_pages 171 172 void 173 set_platform_defaults(void) 174 { 175 extern int watchdog_enable; 176 extern uint64_t xc_tick_limit_scale; 177 extern void mmu_init_large_pages(size_t); 178 179 #ifdef DEBUG 180 char *todsg_name = "todsg"; 181 ce_verbose_memory = 2; 182 ce_verbose_other = 2; 183 #endif /* DEBUG */ 184 185 watchdog_enable = TRUE; 186 watchdog_available = TRUE; 187 188 cpu_sgn_func = cpu_sgn_update; 189 190 #ifdef DEBUG 191 /* tod_module_name should be set to "todsg" from OBP property */ 192 if (tod_module_name && (strcmp(tod_module_name, todsg_name) == 0)) 193 prom_printf("Using todsg driver\n"); 194 else { 195 prom_printf("Force using todsg driver\n"); 196 tod_module_name = todsg_name; 197 } 198 #endif /* DEBUG */ 199 200 /* lw8 does not support forthdebug */ 201 forthdebug_supported = 0; 202 203 204 /* 205 * Some DR operations require the system to be sync paused. 206 * Sync pause on Serengeti could potentially take up to 4 207 * seconds to complete depending on the load on the SC. To 208 * avoid send_mond panics during such operations, we need to 209 * increase xc_tick_limit to a larger value on Serengeti by 210 * setting xc_tick_limit_scale to 5. 211 */ 212 xc_tick_limit_scale = 5; 213 214 if ((mmu_page_sizes == max_mmu_page_sizes) && 215 (mmu_ism_pagesize != DEFAULT_ISM_PAGESIZE)) { 216 if (&mmu_init_large_pages) 217 mmu_init_large_pages(mmu_ism_pagesize); 218 } 219 } 220 221 void 222 load_platform_modules(void) 223 { 224 if (modload("misc", "pcihp") < 0) { 225 cmn_err(CE_NOTE, "pcihp driver failed to load"); 226 } 227 } 228 229 /*ARGSUSED*/ 230 int 231 plat_cpu_poweron(struct cpu *cp) 232 { 233 int (*serengeti_cpu_poweron)(struct cpu *) = NULL; 234 235 serengeti_cpu_poweron = 236 (int (*)(struct cpu *))modgetsymvalue("sbdp_cpu_poweron", 0); 237 238 if (serengeti_cpu_poweron == NULL) 239 return (ENOTSUP); 240 else 241 return ((serengeti_cpu_poweron)(cp)); 242 } 243 244 /*ARGSUSED*/ 245 int 246 plat_cpu_poweroff(struct cpu *cp) 247 { 248 int (*serengeti_cpu_poweroff)(struct cpu *) = NULL; 249 250 serengeti_cpu_poweroff = 251 (int (*)(struct cpu *))modgetsymvalue("sbdp_cpu_poweroff", 0); 252 253 if (serengeti_cpu_poweroff == NULL) 254 return (ENOTSUP); 255 else 256 return ((serengeti_cpu_poweroff)(cp)); 257 } 258 259 #ifdef DEBUG 260 pgcnt_t serengeti_cage_size_limit; 261 #endif 262 263 /* Preferred minimum cage size (expressed in pages)... for DR */ 264 pgcnt_t serengeti_minimum_cage_size = 0; 265 266 void 267 set_platform_cage_params(void) 268 { 269 extern pgcnt_t total_pages; 270 extern struct memlist *phys_avail; 271 272 if (kernel_cage_enable) { 273 pgcnt_t preferred_cage_size; 274 275 preferred_cage_size = 276 MAX(serengeti_minimum_cage_size, total_pages / 256); 277 #ifdef DEBUG 278 if (serengeti_cage_size_limit) 279 preferred_cage_size = serengeti_cage_size_limit; 280 #endif 281 /* 282 * Post copies obp into the lowest slice. This requires the 283 * cage to grow upwards 284 */ 285 kcage_range_init(phys_avail, KCAGE_UP, preferred_cage_size); 286 } 287 288 /* Only note when the cage is off since it should always be on. */ 289 if (!kcage_on) 290 cmn_err(CE_NOTE, "!DR Kernel Cage is DISABLED"); 291 } 292 293 #define ALIGN(x, a) ((a) == 0 ? (uint64_t)(x) : \ 294 (((uint64_t)(x) + (uint64_t)(a) - 1l) & ~((uint64_t)(a) - 1l))) 295 296 void 297 update_mem_bounds(int brd, uint64_t base, uint64_t sz) 298 { 299 uint64_t end; 300 int mnode; 301 302 end = base + sz - 1; 303 304 /* 305 * First see if this board already has a memnode associated 306 * with it. If not, see if this slice has a memnode. This 307 * covers the cases where a single slice covers multiple 308 * boards (cross-board interleaving) and where a single 309 * board has multiple slices (1+GB DIMMs). 310 */ 311 if ((mnode = plat_lgrphand_to_mem_node(brd)) == -1) { 312 if ((mnode = slice_to_memnode[PA_2_SLICE(base)]) == -1) 313 mnode = mem_node_alloc(); 314 plat_assign_lgrphand_to_mem_node(brd, mnode); 315 } 316 317 /* 318 * Align base at 16GB boundary 319 */ 320 base = ALIGN(base, (1ul << PA_SLICE_SHIFT)); 321 322 while (base < end) { 323 slice_to_memnode[PA_2_SLICE(base)] = mnode; 324 base += (1ul << PA_SLICE_SHIFT); 325 } 326 } 327 328 /* 329 * Dynamically detect memory slices in the system by decoding 330 * the cpu memory decoder registers at boot time. 331 */ 332 void 333 plat_fill_mc(pnode_t nodeid) 334 { 335 uint64_t mc_addr, mask; 336 uint64_t mc_decode[SG_MAX_BANKS_PER_MC]; 337 uint64_t base, size; 338 uint32_t regs[4]; 339 int len; 340 int local_mc; 341 int portid; 342 int boardid; 343 int i; 344 345 if ((prom_getprop(nodeid, "portid", (caddr_t)&portid) < 0) || 346 (portid == -1)) 347 return; 348 349 /* 350 * Decode the board number from the MC portid 351 */ 352 boardid = SG_PORTID_TO_BOARD_NUM(portid); 353 354 /* 355 * The "reg" property returns 4 32-bit values. The first two are 356 * combined to form a 64-bit address. The second two are for a 357 * 64-bit size, but we don't actually need to look at that value. 358 */ 359 len = prom_getproplen(nodeid, "reg"); 360 if (len != (sizeof (uint32_t) * 4)) { 361 prom_printf("Warning: malformed 'reg' property\n"); 362 return; 363 } 364 if (prom_getprop(nodeid, "reg", (caddr_t)regs) < 0) 365 return; 366 mc_addr = ((uint64_t)regs[0]) << 32; 367 mc_addr |= (uint64_t)regs[1]; 368 369 /* 370 * Figure out whether the memory controller we are examining 371 * belongs to this CPU or a different one. 372 */ 373 if (portid == cpunodes[CPU->cpu_id].portid) 374 local_mc = 1; 375 else 376 local_mc = 0; 377 378 for (i = 0; i < SG_MAX_BANKS_PER_MC; i++) { 379 mask = SG_REG_2_OFFSET(i); 380 381 /* 382 * If the memory controller is local to this CPU, we use 383 * the special ASI to read the decode registers. 384 * Otherwise, we load the values from a magic address in 385 * I/O space. 386 */ 387 if (local_mc) 388 mc_decode[i] = lddmcdecode(mask & MC_OFFSET_MASK); 389 else 390 mc_decode[i] = lddphysio((mc_addr | mask)); 391 392 if (mc_decode[i] >> MC_VALID_SHIFT) { 393 /* 394 * The memory decode register is a bitmask field, 395 * so we can decode that into both a base and 396 * a span. 397 */ 398 base = MC_BASE(mc_decode[i]) << PHYS2UM_SHIFT; 399 size = MC_UK2SPAN(mc_decode[i]); 400 update_mem_bounds(boardid, base, size); 401 } 402 } 403 } 404 405 /* 406 * This routine is run midway through the boot process. By the time we get 407 * here, we know about all the active CPU boards in the system, and we have 408 * extracted information about each board's memory from the memory 409 * controllers. We have also figured out which ranges of memory will be 410 * assigned to which memnodes, so we walk the slice table to build the table 411 * of memnodes. 412 */ 413 /* ARGSUSED */ 414 void 415 plat_build_mem_nodes(u_longlong_t *list, size_t nelems) 416 { 417 int slice; 418 pfn_t basepfn; 419 pgcnt_t npgs; 420 421 mem_node_pfn_shift = PFN_SLICE_SHIFT; 422 mem_node_physalign = (1ull << PA_SLICE_SHIFT); 423 424 for (slice = 0; slice < SG_MAX_SLICE; slice++) { 425 if (slice_to_memnode[slice] == -1) 426 continue; 427 basepfn = (uint64_t)slice << PFN_SLICE_SHIFT; 428 npgs = 1ull << PFN_SLICE_SHIFT; 429 mem_node_add_slice(basepfn, basepfn + npgs - 1); 430 } 431 } 432 433 int 434 plat_pfn_to_mem_node(pfn_t pfn) 435 { 436 int node; 437 438 node = slice_to_memnode[PFN_2_SLICE(pfn)]; 439 440 return (node); 441 } 442 443 /* 444 * Serengeti support for lgroups. 445 * 446 * On Serengeti, an lgroup platform handle == board number. 447 * 448 * Mappings between lgroup handles and memnodes are managed 449 * in addition to mappings between memory slices and memnodes 450 * to support cross-board interleaving as well as multiple 451 * slices per board (e.g. >1GB DIMMs). The initial mapping 452 * of memnodes to lgroup handles is determined at boot time. 453 * A DR addition of memory adds a new mapping. A DR copy-rename 454 * swaps mappings. 455 */ 456 457 /* 458 * Macro for extracting the board number from the CPU id 459 */ 460 #define CPUID_TO_BOARD(id) (((id) >> 2) & 0x7) 461 462 /* 463 * Return the platform handle for the lgroup containing the given CPU 464 * 465 * For Serengeti, lgroup platform handle == board number 466 */ 467 lgrp_handle_t 468 plat_lgrp_cpu_to_hand(processorid_t id) 469 { 470 return (CPUID_TO_BOARD(id)); 471 } 472 473 /* 474 * Platform specific lgroup initialization 475 */ 476 void 477 plat_lgrp_init(void) 478 { 479 int i; 480 extern uint32_t lgrp_expand_proc_thresh; 481 extern uint32_t lgrp_expand_proc_diff; 482 483 /* 484 * Initialize lookup tables to invalid values so we catch 485 * any illegal use of them. 486 */ 487 for (i = 0; i < SG_MAX_SLICE; i++) { 488 slice_to_memnode[i] = -1; 489 } 490 491 /* 492 * Set tuneables for Serengeti architecture 493 * 494 * lgrp_expand_proc_thresh is the minimum load on the lgroups 495 * this process is currently running on before considering 496 * expanding threads to another lgroup. 497 * 498 * lgrp_expand_proc_diff determines how much less the remote lgroup 499 * must be loaded before expanding to it. 500 * 501 * Bandwidth is maximized on Serengeti by spreading load across 502 * the machine. The impact to inter-thread communication isn't 503 * too costly since remote latencies are relatively low. These 504 * values equate to one CPU's load and so attempt to spread the 505 * load out across as many lgroups as possible one CPU at a time. 506 */ 507 lgrp_expand_proc_thresh = LGRP_LOADAVG_THREAD_MAX; 508 lgrp_expand_proc_diff = LGRP_LOADAVG_THREAD_MAX; 509 } 510 511 /* 512 * Platform notification of lgroup (re)configuration changes 513 */ 514 /*ARGSUSED*/ 515 void 516 plat_lgrp_config(lgrp_config_flag_t evt, uintptr_t arg) 517 { 518 update_membounds_t *umb; 519 lgrp_config_mem_rename_t lmr; 520 lgrp_handle_t shand, thand; 521 int snode, tnode; 522 523 switch (evt) { 524 525 case LGRP_CONFIG_MEM_ADD: 526 umb = (update_membounds_t *)arg; 527 update_mem_bounds(umb->u_board, umb->u_base, umb->u_len); 528 529 break; 530 531 case LGRP_CONFIG_MEM_DEL: 532 /* We don't have to do anything */ 533 534 break; 535 536 case LGRP_CONFIG_MEM_RENAME: 537 /* 538 * During a DR copy-rename operation, all of the memory 539 * on one board is moved to another board -- but the 540 * addresses/pfns and memnodes don't change. This means 541 * the memory has changed locations without changing identity. 542 * 543 * Source is where we are copying from and target is where we 544 * are copying to. After source memnode is copied to target 545 * memnode, the physical addresses of the target memnode are 546 * renamed to match what the source memnode had. Then target 547 * memnode can be removed and source memnode can take its 548 * place. 549 * 550 * To do this, swap the lgroup handle to memnode mappings for 551 * the boards, so target lgroup will have source memnode and 552 * source lgroup will have empty target memnode which is where 553 * its memory will go (if any is added to it later). 554 * 555 * Then source memnode needs to be removed from its lgroup 556 * and added to the target lgroup where the memory was living 557 * but under a different name/memnode. The memory was in the 558 * target memnode and now lives in the source memnode with 559 * different physical addresses even though it is the same 560 * memory. 561 */ 562 shand = arg & 0xffff; 563 thand = (arg & 0xffff0000) >> 16; 564 snode = plat_lgrphand_to_mem_node(shand); 565 tnode = plat_lgrphand_to_mem_node(thand); 566 567 plat_assign_lgrphand_to_mem_node(thand, snode); 568 plat_assign_lgrphand_to_mem_node(shand, tnode); 569 570 /* 571 * Remove source memnode of copy rename from its lgroup 572 * and add it to its new target lgroup 573 */ 574 lmr.lmem_rename_from = shand; 575 lmr.lmem_rename_to = thand; 576 577 lgrp_config(LGRP_CONFIG_MEM_RENAME, (uintptr_t)snode, 578 (uintptr_t)&lmr); 579 580 break; 581 582 default: 583 break; 584 } 585 } 586 587 /* 588 * Return latency between "from" and "to" lgroups 589 * 590 * This latency number can only be used for relative comparison 591 * between lgroups on the running system, cannot be used across platforms, 592 * and may not reflect the actual latency. It is platform and implementation 593 * specific, so platform gets to decide its value. It would be nice if the 594 * number was at least proportional to make comparisons more meaningful though. 595 * NOTE: The numbers below are supposed to be load latencies for uncached 596 * memory divided by 10. 597 */ 598 int 599 plat_lgrp_latency(lgrp_handle_t from, lgrp_handle_t to) 600 { 601 /* 602 * Return min remote latency when there are more than two lgroups 603 * (root and child) and getting latency between two different lgroups 604 * or root is involved 605 */ 606 if (lgrp_optimizations() && (from != to || 607 from == LGRP_DEFAULT_HANDLE || to == LGRP_DEFAULT_HANDLE)) 608 return (28); 609 else 610 return (23); 611 } 612 613 /* ARGSUSED */ 614 void 615 plat_freelist_process(int mnode) 616 { 617 } 618 619 /* 620 * Find dip for chosen IOSRAM 621 */ 622 dev_info_t * 623 find_chosen_dip(void) 624 { 625 dev_info_t *dip; 626 char master_sbbc[MAXNAMELEN]; 627 int nodeid; 628 uint_t tunnel; 629 630 /* 631 * find the /chosen SBBC node, prom interface will handle errors 632 */ 633 nodeid = prom_chosennode(); 634 /* 635 * get the 'iosram' property from the /chosen node 636 */ 637 if (prom_getprop(nodeid, IOSRAM_CHOSEN_PROP, (caddr_t)&tunnel) <= 0) { 638 SBBC_ERR(CE_PANIC, "No iosram property found! \n"); 639 } 640 641 if (prom_phandle_to_path((phandle_t)tunnel, master_sbbc, 642 sizeof (master_sbbc)) < 0) { 643 SBBC_ERR1(CE_PANIC, "prom_phandle_to_path(%d) failed\n", 644 tunnel); 645 } 646 647 chosen_nodeid = nodeid; 648 649 /* 650 * load and attach the sgsbbc driver. 651 * This will also attach all the sgsbbc driver instances 652 */ 653 if (i_ddi_attach_hw_nodes("sgsbbc") != DDI_SUCCESS) { 654 cmn_err(CE_WARN, "sgsbbc failed to load\n"); 655 } 656 /* translate a path name to a dev_info_t */ 657 dip = e_ddi_hold_devi_by_path(master_sbbc, 0); 658 if ((dip == NULL) || (ddi_get_nodeid(dip) != tunnel)) { 659 cmn_err(CE_PANIC, 660 "e_ddi_hold_devi_by_path(%x) failed for SBBC\n", 661 tunnel); 662 } 663 664 /* make sure devi_ref is ZERO */ 665 ndi_rele_devi(dip); 666 DCMNERR(CE_CONT, "Chosen IOSRAM is at %s \n", master_sbbc); 667 668 return (dip); 669 } 670 671 void 672 load_platform_drivers(void) 673 { 674 int ret; 675 676 /* 677 * Load the mc-us3 memory driver. 678 */ 679 if (i_ddi_attach_hw_nodes("mc-us3") != DDI_SUCCESS) 680 cmn_err(CE_WARN, "mc-us3 failed to load"); 681 else 682 (void) ddi_hold_driver(ddi_name_to_major("mc-us3")); 683 684 /* 685 * Initialize the chosen IOSRAM before its clients 686 * are loaded. 687 */ 688 (void) find_chosen_dip(); 689 690 /* 691 * Load the environmentals driver (sgenv) 692 * 693 * We need this driver to handle events from the SC when state 694 * changes occur in the environmental data. 695 */ 696 if (i_ddi_attach_hw_nodes("sgenv") != DDI_SUCCESS) 697 cmn_err(CE_WARN, "sgenv failed to load"); 698 699 /* 700 * Ideally, we'd do this in set_platform_defaults(), but 701 * at that point it's too early to look up symbols. 702 */ 703 iosram_write_ptr = (int (*)(int, uint32_t, caddr_t, uint32_t)) 704 modgetsymvalue("iosram_write", 0); 705 706 if (iosram_write_ptr == NULL) { 707 DCMNERR(CE_WARN, "load_platform_defaults: iosram_write()" 708 " not found; signatures will not be updated\n"); 709 } else { 710 /* 711 * The iosram read ptr is only needed if we can actually 712 * write CPU signatures, so only bother setting it if we 713 * set a valid write pointer, above. 714 */ 715 iosram_read_ptr = (int (*)(int, uint32_t, caddr_t, uint32_t)) 716 modgetsymvalue("iosram_read", 0); 717 718 if (iosram_read_ptr == NULL) 719 DCMNERR(CE_WARN, "load_platform_defaults: iosram_read()" 720 " not found\n"); 721 } 722 723 /* 724 * Set todsg_use_sc to TRUE so that we will be getting date 725 * from the SC. 726 */ 727 todsg_use_sc = TRUE; 728 729 /* 730 * Now is a good time to activate hardware watchdog (if one exists). 731 */ 732 mutex_enter(&tod_lock); 733 if (watchdog_enable) 734 ret = tod_ops.tod_set_watchdog_timer(watchdog_timeout_seconds); 735 mutex_exit(&tod_lock); 736 if (ret != 0) 737 printf("Hardware watchdog enabled\n"); 738 739 plat_ecc_init(); 740 } 741 742 /* 743 * No platform drivers on this platform 744 */ 745 char *platform_module_list[] = { 746 (char *)0 747 }; 748 749 /*ARGSUSED*/ 750 void 751 plat_tod_fault(enum tod_fault_type tod_bad) 752 { 753 } 754 int 755 plat_max_boards() 756 { 757 return (SG_MAX_BDS); 758 } 759 int 760 plat_max_io_units_per_board() 761 { 762 return (SG_MAX_IO_PER_BD); 763 } 764 int 765 plat_max_cmp_units_per_board() 766 { 767 return (SG_MAX_CMPS_PER_BD); 768 } 769 int 770 plat_max_cpu_units_per_board() 771 { 772 return (SG_MAX_CPUS_PER_BD); 773 } 774 775 int 776 plat_max_mc_units_per_board() 777 { 778 return (SG_MAX_CMPS_PER_BD); /* each CPU die has a memory controller */ 779 } 780 781 int 782 plat_max_mem_units_per_board() 783 { 784 return (SG_MAX_MEM_PER_BD); 785 } 786 787 int 788 plat_max_cpumem_boards(void) 789 { 790 return (LW8_MAX_CPU_BDS); 791 } 792 793 int 794 set_platform_max_ncpus(void) 795 { 796 return (sg_max_ncpus); 797 } 798 799 void 800 plat_dmv_params(uint_t *hwint, uint_t *swint) 801 { 802 *hwint = MAX_UPA; 803 *swint = 0; 804 } 805 806 static int (*sg_mbox)(sbbc_msg_t *, sbbc_msg_t *, time_t) = NULL; 807 808 /* 809 * Our nodename has been set, pass it along to the SC. 810 */ 811 void 812 plat_nodename_set(void) 813 { 814 sbbc_msg_t req; /* request */ 815 sbbc_msg_t resp; /* response */ 816 int rv; /* return value from call to mbox */ 817 struct nodename_info { 818 int32_t namelen; 819 char nodename[_SYS_NMLN]; 820 } nni; 821 822 /* 823 * find the symbol for the mailbox routine 824 */ 825 if (sg_mbox == NULL) 826 sg_mbox = (int (*)(sbbc_msg_t *, sbbc_msg_t *, time_t)) 827 modgetsymvalue("sbbc_mbox_request_response", 0); 828 829 if (sg_mbox == NULL) { 830 cmn_err(CE_NOTE, "!plat_nodename_set: sg_mbox not found\n"); 831 return; 832 } 833 834 /* 835 * construct the message telling the SC our nodename 836 */ 837 (void) strcpy(nni.nodename, utsname.nodename); 838 nni.namelen = (int32_t)strlen(nni.nodename); 839 840 req.msg_type.type = INFO_MBOX; 841 req.msg_type.sub_type = INFO_MBOX_NODENAME; 842 req.msg_status = 0; 843 req.msg_len = (int)(nni.namelen + sizeof (nni.namelen)); 844 req.msg_bytes = 0; 845 req.msg_buf = (caddr_t)&nni; 846 req.msg_data[0] = 0; 847 req.msg_data[1] = 0; 848 849 /* 850 * initialize the response back from the SC 851 */ 852 resp.msg_type.type = INFO_MBOX; 853 resp.msg_type.sub_type = INFO_MBOX_NODENAME; 854 resp.msg_status = 0; 855 resp.msg_len = 0; 856 resp.msg_bytes = 0; 857 resp.msg_buf = (caddr_t)0; 858 resp.msg_data[0] = 0; 859 resp.msg_data[1] = 0; 860 861 /* 862 * ship it and check for success 863 */ 864 rv = (sg_mbox)(&req, &resp, sbbc_mbox_default_timeout); 865 866 if (rv != 0) { 867 cmn_err(CE_NOTE, "!plat_nodename_set: sg_mbox retval %d\n", rv); 868 } else if (resp.msg_status != 0) { 869 cmn_err(CE_NOTE, "!plat_nodename_set: msg_status %d\n", 870 resp.msg_status); 871 } else { 872 DCMNERR(CE_NOTE, "!plat_nodename_set was successful\n"); 873 874 /* 875 * It is necessary to exchange capability the bitmap 876 * with SC before sending any ecc error information and 877 * indictment. We are calling the plat_ecc_capability_send() 878 * here just after sending the nodename successfully. 879 */ 880 rv = plat_ecc_capability_send(); 881 if (rv == 0) { 882 DCMNERR(CE_NOTE, "!plat_ecc_capability_send was" 883 "successful\n"); 884 } 885 } 886 } 887 888 /* 889 * flag to allow users switch between using OBP's 890 * prom_get_unum() and mc-us3 driver's p2get_mem_unum() 891 * (for main memory errors only). 892 */ 893 int sg_use_prom_get_unum = 0; 894 895 /* 896 * Debugging flag: set to 1 to call into obp for get_unum, or set it to 0 897 * to call into the unum cache system. This is the E$ equivalent of 898 * sg_use_prom_get_unum. 899 */ 900 int sg_use_prom_ecache_unum = 0; 901 902 /* used for logging ECC errors to the SC */ 903 #define SG_MEMORY_ECC 1 904 #define SG_ECACHE_ECC 2 905 #define SG_UNKNOWN_ECC (-1) 906 907 /* 908 * plat_get_mem_unum() generates a string identifying either the 909 * memory or E$ DIMM(s) during error logging. Depending on whether 910 * the error is E$ or memory related, the appropriate support 911 * routine is called to assist in the string generation. 912 * 913 * - For main memory errors we can use the mc-us3 drivers p2getunum() 914 * (or prom_get_unum() for debugging purposes). 915 * 916 * - For E$ errors we call sg_get_ecacheunum() to generate the unum (or 917 * prom_serengeti_get_ecacheunum() for debugging purposes). 918 */ 919 920 static int 921 sg_prom_get_unum(int synd_code, uint64_t paddr, char *buf, int buflen, 922 int *lenp) 923 { 924 if ((prom_get_unum(synd_code, (unsigned long long)paddr, 925 buf, buflen, lenp)) != 0) 926 return (EIO); 927 else if (*lenp <= 1) 928 return (EINVAL); 929 else 930 return (0); 931 } 932 933 /*ARGSUSED*/ 934 int 935 plat_get_mem_unum(int synd_code, uint64_t flt_addr, int flt_bus_id, 936 int flt_in_memory, ushort_t flt_status, char *buf, int buflen, int *lenp) 937 { 938 /* 939 * unum_func will either point to the memory drivers p2get_mem_unum() 940 * or to prom_get_unum() for memory errors. 941 */ 942 int (*unum_func)(int synd_code, uint64_t paddr, char *buf, 943 int buflen, int *lenp) = p2get_mem_unum; 944 945 /* 946 * check if it's a Memory or an Ecache error. 947 */ 948 if (flt_in_memory) { 949 /* 950 * It's a main memory error. 951 * 952 * For debugging we allow the user to switch between 953 * using OBP's get_unum and the memory driver's get_unum 954 * so we create a pointer to the functions and switch 955 * depending on the sg_use_prom_get_unum flag. 956 */ 957 if (sg_use_prom_get_unum) { 958 DCMNERR(CE_NOTE, "Using prom_get_unum from OBP"); 959 return (sg_prom_get_unum(synd_code, 960 P2ALIGN(flt_addr, 8), buf, buflen, lenp)); 961 } else if (unum_func != NULL) { 962 return (unum_func(synd_code, P2ALIGN(flt_addr, 8), 963 buf, buflen, lenp)); 964 } else { 965 return (ENOTSUP); 966 } 967 } else if (flt_status & ECC_ECACHE) { 968 /* 969 * It's an E$ error. 970 */ 971 if (sg_use_prom_ecache_unum) { 972 /* 973 * We call to OBP to handle this. 974 */ 975 DCMNERR(CE_NOTE, 976 "Using prom_serengeti_get_ecacheunum from OBP"); 977 if (prom_serengeti_get_ecacheunum(flt_bus_id, 978 P2ALIGN(flt_addr, 8), buf, buflen, lenp) != 0) { 979 return (EIO); 980 } 981 } else { 982 return (sg_get_ecacheunum(flt_bus_id, flt_addr, 983 buf, buflen, lenp)); 984 } 985 } else { 986 return (ENOTSUP); 987 } 988 989 return (0); 990 } 991 992 /* 993 * This platform hook gets called from mc_add_mem_unum_label() in the mc-us3 994 * driver giving each platform the opportunity to add platform 995 * specific label information to the unum for ECC error logging purposes. 996 */ 997 void 998 plat_add_mem_unum_label(char *unum, int mcid, int bank, int dimm) 999 { 1000 char new_unum[UNUM_NAMLEN] = ""; 1001 int node = SG_PORTID_TO_NODEID(mcid); 1002 int board = SG_CPU_BD_PORTID_TO_BD_NUM(mcid); 1003 int position = SG_PORTID_TO_CPU_POSN(mcid); 1004 1005 /* 1006 * The mc-us3 driver deals with logical banks but for unum 1007 * purposes we need to use physical banks so that the correct 1008 * dimm can be physically located. Logical banks 0 and 2 1009 * make up physical bank 0. Logical banks 1 and 3 make up 1010 * physical bank 1. Here we do the necessary conversion. 1011 */ 1012 bank = (bank % 2); 1013 1014 if (dimm == -1) { 1015 SG_SET_FRU_NAME_NODE(new_unum, node); 1016 SG_SET_FRU_NAME_CPU_BOARD(new_unum, board); 1017 SG_SET_FRU_NAME_MODULE(new_unum, position); 1018 SG_SET_FRU_NAME_BANK(new_unum, bank); 1019 1020 } else { 1021 SG_SET_FRU_NAME_NODE(new_unum, node); 1022 SG_SET_FRU_NAME_CPU_BOARD(new_unum, board); 1023 SG_SET_FRU_NAME_MODULE(new_unum, position); 1024 SG_SET_FRU_NAME_BANK(new_unum, bank); 1025 SG_SET_FRU_NAME_DIMM(new_unum, dimm); 1026 1027 strcat(new_unum, " "); 1028 strcat(new_unum, unum); 1029 } 1030 1031 strcpy(unum, new_unum); 1032 } 1033 1034 int 1035 plat_get_cpu_unum(int cpuid, char *buf, int buflen, int *lenp) 1036 { 1037 int node = SG_PORTID_TO_NODEID(cpuid); 1038 int board = SG_CPU_BD_PORTID_TO_BD_NUM(cpuid); 1039 1040 if (snprintf(buf, buflen, "/N%d/%s%d", node, 1041 SG_HPU_TYPE_CPU_BOARD_ID, board) >= buflen) { 1042 return (ENOSPC); 1043 } else { 1044 *lenp = strlen(buf); 1045 return (0); 1046 } 1047 } 1048 1049 static void (*sg_ecc_taskq_func)(sbbc_ecc_mbox_t *) = NULL; 1050 static int (*sg_ecc_mbox_func)(sbbc_ecc_mbox_t *) = NULL; 1051 1052 /* 1053 * We log all ECC errors to the SC so we send a mailbox 1054 * message to the SC passing it the relevant data. 1055 * ECC mailbox messages are sent via a taskq mechanism to 1056 * prevent impaired system performance during ECC floods. 1057 * Indictments have already passed through a taskq, so they 1058 * are not queued here. 1059 */ 1060 int 1061 plat_send_ecc_mailbox_msg(plat_ecc_message_type_t msg_type, void *datap) 1062 { 1063 sbbc_ecc_mbox_t *msgp; 1064 uint16_t msg_subtype; 1065 int sleep_flag, log_error; 1066 size_t msg_size; 1067 1068 if (sg_ecc_taskq_func == NULL) { 1069 sg_ecc_taskq_func = (void (*)(sbbc_ecc_mbox_t *)) 1070 modgetsymvalue("sbbc_mbox_queue_ecc_event", 0); 1071 if (sg_ecc_taskq_func == NULL) { 1072 cmn_err(CE_NOTE, "!plat_send_ecc_mailbox_msg: " 1073 "sbbc_mbox_queue_ecc_event not found"); 1074 return (ENODEV); 1075 } 1076 } 1077 if (sg_ecc_mbox_func == NULL) { 1078 sg_ecc_mbox_func = (int (*)(sbbc_ecc_mbox_t *)) 1079 modgetsymvalue("sbbc_mbox_ecc_output", 0); 1080 if (sg_ecc_mbox_func == NULL) { 1081 cmn_err(CE_NOTE, "!plat_send_ecc_mailbox_msg: " 1082 "sbbc_mbox_ecc_output not found"); 1083 return (ENODEV); 1084 } 1085 } 1086 1087 /* 1088 * Initialize the request and response structures 1089 */ 1090 switch (msg_type) { 1091 case PLAT_ECC_ERROR_MESSAGE: 1092 msg_subtype = INFO_MBOX_ERROR_ECC; 1093 msg_size = sizeof (plat_ecc_error_data_t); 1094 sleep_flag = KM_NOSLEEP; 1095 log_error = 1; 1096 break; 1097 case PLAT_ECC_ERROR2_MESSAGE: 1098 msg_subtype = INFO_MBOX_ECC; 1099 msg_size = sizeof (plat_ecc_error2_data_t); 1100 sleep_flag = KM_NOSLEEP; 1101 log_error = 1; 1102 break; 1103 case PLAT_ECC_INDICTMENT_MESSAGE: 1104 msg_subtype = INFO_MBOX_ERROR_INDICT; 1105 msg_size = sizeof (plat_ecc_indictment_data_t); 1106 sleep_flag = KM_SLEEP; 1107 log_error = 0; 1108 break; 1109 case PLAT_ECC_INDICTMENT2_MESSAGE: 1110 msg_subtype = INFO_MBOX_ECC; 1111 msg_size = sizeof (plat_ecc_indictment2_data_t); 1112 sleep_flag = KM_SLEEP; 1113 log_error = 0; 1114 break; 1115 case PLAT_ECC_CAPABILITY_MESSAGE: 1116 msg_subtype = INFO_MBOX_ECC_CAP; 1117 msg_size = sizeof (plat_capability_data_t) + 1118 strlen(utsname.release) + strlen(utsname.version) + 2; 1119 sleep_flag = KM_SLEEP; 1120 log_error = 0; 1121 break; 1122 case PLAT_ECC_DIMM_SID_MESSAGE: 1123 msg_subtype = INFO_MBOX_ECC; 1124 msg_size = sizeof (plat_dimm_sid_request_data_t); 1125 sleep_flag = KM_SLEEP; 1126 log_error = 0; 1127 break; 1128 default: 1129 return (EINVAL); 1130 } 1131 1132 msgp = (sbbc_ecc_mbox_t *)kmem_zalloc(sizeof (sbbc_ecc_mbox_t), 1133 sleep_flag); 1134 if (msgp == NULL) { 1135 cmn_err(CE_NOTE, "!plat_send_ecc_mailbox_msg: " 1136 "unable to allocate sbbc_ecc_mbox"); 1137 return (ENOMEM); 1138 } 1139 1140 msgp->ecc_log_error = log_error; 1141 1142 msgp->ecc_req.msg_type.type = INFO_MBOX; 1143 msgp->ecc_req.msg_type.sub_type = msg_subtype; 1144 msgp->ecc_req.msg_status = 0; 1145 msgp->ecc_req.msg_len = (int)msg_size; 1146 msgp->ecc_req.msg_bytes = 0; 1147 msgp->ecc_req.msg_buf = (caddr_t)kmem_zalloc(msg_size, sleep_flag); 1148 msgp->ecc_req.msg_data[0] = 0; 1149 msgp->ecc_req.msg_data[1] = 0; 1150 1151 if (msgp->ecc_req.msg_buf == NULL) { 1152 cmn_err(CE_NOTE, "!plat_send_ecc_mailbox_msg: " 1153 "unable to allocate request msg_buf"); 1154 kmem_free((void *)msgp, sizeof (sbbc_ecc_mbox_t)); 1155 return (ENOMEM); 1156 } 1157 1158 bcopy(datap, (void *)msgp->ecc_req.msg_buf, msg_size); 1159 1160 /* 1161 * initialize the response back from the SC 1162 */ 1163 msgp->ecc_resp.msg_type.type = INFO_MBOX; 1164 msgp->ecc_resp.msg_type.sub_type = msg_subtype; 1165 msgp->ecc_resp.msg_status = 0; 1166 msgp->ecc_resp.msg_len = 0; 1167 msgp->ecc_resp.msg_bytes = 0; 1168 msgp->ecc_resp.msg_buf = NULL; 1169 msgp->ecc_resp.msg_data[0] = 0; 1170 msgp->ecc_resp.msg_data[1] = 0; 1171 1172 switch (msg_type) { 1173 case PLAT_ECC_ERROR_MESSAGE: 1174 case PLAT_ECC_ERROR2_MESSAGE: 1175 /* 1176 * For Error Messages, we go through a taskq. 1177 * Queue up message for processing 1178 */ 1179 (*sg_ecc_taskq_func)(msgp); 1180 return (0); 1181 1182 case PLAT_ECC_CAPABILITY_MESSAGE: 1183 /* 1184 * For indictment and capability messages, we've already gone 1185 * through the taskq, so we can call the mailbox routine 1186 * directly. Find the symbol for the routine that sends 1187 * the mailbox msg 1188 */ 1189 msgp->ecc_resp.msg_len = (int)msg_size; 1190 msgp->ecc_resp.msg_buf = (caddr_t)kmem_zalloc(msg_size, 1191 sleep_flag); 1192 /* FALLTHRU */ 1193 1194 case PLAT_ECC_INDICTMENT_MESSAGE: 1195 case PLAT_ECC_INDICTMENT2_MESSAGE: 1196 return ((*sg_ecc_mbox_func)(msgp)); 1197 1198 case PLAT_ECC_DIMM_SID_MESSAGE: 1199 msgp->ecc_resp.msg_len = sizeof (plat_dimm_sid_board_data_t); 1200 msgp->ecc_resp.msg_buf = (caddr_t)kmem_zalloc( 1201 sizeof (plat_dimm_sid_board_data_t), sleep_flag); 1202 1203 return ((*sg_ecc_mbox_func)(msgp)); 1204 1205 default: 1206 ASSERT(0); 1207 return (EINVAL); 1208 } 1209 } 1210 1211 /* 1212 * m is redundant on serengeti as the multiplyer is always 4 1213 */ 1214 /*ARGSUSED*/ 1215 int 1216 plat_make_fru_cpuid(int sb, int m, int proc) 1217 { 1218 return (MAKE_CPUID(sb, proc)); 1219 } 1220 1221 /* 1222 * board number for a given proc 1223 */ 1224 int 1225 plat_make_fru_boardnum(int proc) 1226 { 1227 return (SG_PORTID_TO_BOARD_NUM(proc)); 1228 } 1229 1230 static 1231 void 1232 cpu_sgn_update(ushort_t sig, uchar_t state, uchar_t sub_state, int cpuid) 1233 { 1234 uint32_t signature = CPU_SIG_BLD(sig, state, sub_state); 1235 sig_state_t current_sgn; 1236 int i; 1237 1238 if (iosram_write_ptr == NULL) { 1239 /* 1240 * If the IOSRAM write pointer isn't set, we won't be able 1241 * to write signatures to ANYTHING, so we may as well just 1242 * write out an error message (if desired) and exit this 1243 * routine now... 1244 */ 1245 DCMNERR(CE_WARN, 1246 "cpu_sgn_update: iosram_write() not found;" 1247 " cannot write signature 0x%x for CPU(s) or domain\n", 1248 signature); 1249 return; 1250 } 1251 1252 1253 /* 1254 * Differentiate a panic reboot from a non-panic reboot in the 1255 * setting of the substate of the signature. 1256 * 1257 * If the new substate is REBOOT and we're rebooting due to a panic, 1258 * then set the new substate to a special value indicating a panic 1259 * reboot, SIGSUBST_PANIC_REBOOT. 1260 * 1261 * A panic reboot is detected by a current (previous) domain signature 1262 * state of SIGST_EXIT, and a new signature substate of SIGSUBST_REBOOT. 1263 * The domain signature state SIGST_EXIT is used as the panic flow 1264 * progresses. 1265 * 1266 * At the end of the panic flow, the reboot occurs but we should now 1267 * one that was involuntary, something that may be quite useful to know 1268 * at OBP level. 1269 */ 1270 if (sub_state == SIGSUBST_REBOOT) { 1271 if (iosram_read_ptr == NULL) { 1272 DCMNERR(CE_WARN, 1273 "cpu_sgn_update: iosram_read() not found;" 1274 " could not check current domain signature\n"); 1275 } else { 1276 (void) (*iosram_read_ptr)(SBBC_SIGBLCK_KEY, 1277 SG_SGNBLK_DOMAINSIG_OFFSET, 1278 (char *)¤t_sgn, sizeof (current_sgn)); 1279 if (current_sgn.state_t.state == SIGST_EXIT) 1280 signature = CPU_SIG_BLD(sig, state, 1281 SIGSUBST_PANIC_REBOOT); 1282 } 1283 } 1284 1285 /* 1286 * cpuid == -1 indicates that the operation applies to all cpus. 1287 */ 1288 if (cpuid >= 0) { 1289 (void) (*iosram_write_ptr)(SBBC_SIGBLCK_KEY, 1290 SG_SGNBLK_CPUSIG_OFFSET(cpuid), (char *)&signature, 1291 sizeof (signature)); 1292 } else { 1293 for (i = 0; i < NCPU; i++) { 1294 if (cpu[i] == NULL || !(cpu[i]->cpu_flags & 1295 (CPU_EXISTS|CPU_QUIESCED))) { 1296 continue; 1297 } 1298 (void) (*iosram_write_ptr)(SBBC_SIGBLCK_KEY, 1299 SG_SGNBLK_CPUSIG_OFFSET(i), (char *)&signature, 1300 sizeof (signature)); 1301 } 1302 } 1303 1304 if (state == SIGST_OFFLINE || state == SIGST_DETACHED) { 1305 return; 1306 } 1307 1308 (void) (*iosram_write_ptr)(SBBC_SIGBLCK_KEY, 1309 SG_SGNBLK_DOMAINSIG_OFFSET, (char *)&signature, 1310 sizeof (signature)); 1311 } 1312 1313 void 1314 startup_platform(void) 1315 { 1316 } 1317 1318 /* 1319 * A routine to convert a number (represented as a string) to 1320 * the integer value it represents. 1321 */ 1322 1323 static int 1324 isdigit(int ch) 1325 { 1326 return (ch >= '0' && ch <= '9'); 1327 } 1328 1329 #define isspace(c) ((c) == ' ' || (c) == '\t' || (c) == '\n') 1330 1331 static int 1332 strtoi(char *p, char **pos) 1333 { 1334 int n; 1335 int c, neg = 0; 1336 1337 if (!isdigit(c = *p)) { 1338 while (isspace(c)) 1339 c = *++p; 1340 switch (c) { 1341 case '-': 1342 neg++; 1343 /* FALLTHROUGH */ 1344 case '+': 1345 c = *++p; 1346 } 1347 if (!isdigit(c)) { 1348 if (pos != NULL) 1349 *pos = p; 1350 return (0); 1351 } 1352 } 1353 for (n = '0' - c; isdigit(c = *++p); ) { 1354 n *= 10; /* two steps to avoid unnecessary overflow */ 1355 n += '0' - c; /* accum neg to avoid surprises at MAX */ 1356 } 1357 if (pos != NULL) 1358 *pos = p; 1359 return (neg ? n : -n); 1360 } 1361 1362 /* 1363 * Get the three parts of the Serengeti PROM version. 1364 * Used for feature readiness tests. 1365 * 1366 * Return 0 if version extracted successfully, -1 otherwise. 1367 */ 1368 1369 int 1370 sg_get_prom_version(int *sysp, int *intfp, int *bldp) 1371 { 1372 int plen; 1373 char vers[512]; 1374 static pnode_t node; 1375 static char version[] = "version"; 1376 char *verp, *ep; 1377 1378 node = prom_finddevice("/openprom"); 1379 if (node == OBP_BADNODE) 1380 return (-1); 1381 1382 plen = prom_getproplen(node, version); 1383 if (plen <= 0 || plen >= sizeof (vers)) 1384 return (-1); 1385 (void) prom_getprop(node, version, vers); 1386 vers[plen] = '\0'; 1387 1388 /* Make sure it's an OBP flashprom */ 1389 if (vers[0] != 'O' && vers[1] != 'B' && vers[2] != 'P') { 1390 cmn_err(CE_WARN, "sg_get_prom_version: " 1391 "unknown <version> string in </openprom>\n"); 1392 return (-1); 1393 } 1394 verp = &vers[4]; 1395 1396 *sysp = strtoi(verp, &ep); 1397 if (ep == verp || *ep != '.') 1398 return (-1); 1399 verp = ep + 1; 1400 1401 *intfp = strtoi(verp, &ep); 1402 if (ep == verp || *ep != '.') 1403 return (-1); 1404 verp = ep + 1; 1405 1406 *bldp = strtoi(verp, &ep); 1407 if (ep == verp || (*ep != '\0' && !isspace(*ep))) 1408 return (-1); 1409 return (0); 1410 } 1411 1412 /* 1413 * Return 0 if system board Dynamic Reconfiguration 1414 * is supported by the firmware, -1 otherwise. 1415 */ 1416 int 1417 sg_prom_sb_dr_check(void) 1418 { 1419 static int prom_res = 1; 1420 1421 if (prom_res == 1) { 1422 int sys, intf, bld; 1423 int rv; 1424 1425 rv = sg_get_prom_version(&sys, &intf, &bld); 1426 if (rv == 0 && sys == 5 && 1427 (intf >= 12 || (intf == 11 && bld >= 200))) { 1428 prom_res = 0; 1429 } else { 1430 prom_res = -1; 1431 } 1432 } 1433 return (prom_res); 1434 } 1435 1436 /* 1437 * Return 0 if cPCI Dynamic Reconfiguration 1438 * is supported by the firmware, -1 otherwise. 1439 */ 1440 int 1441 sg_prom_cpci_dr_check(void) 1442 { 1443 /* 1444 * The version check is currently the same as for 1445 * system boards. Since the two DR sub-systems are 1446 * independent, this could change. 1447 */ 1448 return (sg_prom_sb_dr_check()); 1449 } 1450 1451 /* 1452 * Our implementation of this KDI op updates the CPU signature in the system 1453 * controller. Note that we set the signature to OBP_SIG, rather than DBG_SIG. 1454 * The Forth words we execute will, among other things, transform our OBP_SIG 1455 * into DBG_SIG. They won't function properly if we try to use DBG_SIG. 1456 */ 1457 static void 1458 sg_system_claim(void) 1459 { 1460 prom_interpret("sigb-sig! my-sigb-sig!", OBP_SIG, OBP_SIG, 0, 0, 0); 1461 } 1462 1463 static void 1464 sg_system_release(void) 1465 { 1466 prom_interpret("sigb-sig! my-sigb-sig!", OS_SIG, OS_SIG, 0, 0, 0); 1467 } 1468 1469 static void 1470 sg_console_claim(void) 1471 { 1472 prom_serengeti_set_console_input(SGCN_OBP_STR); 1473 } 1474 1475 static void 1476 sg_console_release(void) 1477 { 1478 prom_serengeti_set_console_input(SGCN_CLNT_STR); 1479 } 1480 1481 void 1482 plat_kdi_init(kdi_t *kdi) 1483 { 1484 kdi->pkdi_system_claim = sg_system_claim; 1485 kdi->pkdi_system_release = sg_system_release; 1486 kdi->pkdi_console_claim = sg_console_claim; 1487 kdi->pkdi_console_release = sg_console_release; 1488 } 1489