1# 2# CDDL HEADER START 3# 4# The contents of this file are subject to the terms of the 5# Common Development and Distribution License, Version 1.0 only 6# (the "License"). You may not use this file except in compliance 7# with the License. 8# 9# You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE 10# or http://www.opensolaris.org/os/licensing. 11# See the License for the specific language governing permissions 12# and limitations under the License. 13# 14# When distributing Covered Code, include this CDDL HEADER in each 15# file and include the License file at usr/src/OPENSOLARIS.LICENSE. 16# If applicable, add the following below this CDDL HEADER, with the 17# fields enclosed by brackets "[]" replaced with your own identifying 18# information: Portions Copyright [yyyy] [name of copyright owner] 19# 20# CDDL HEADER END 21# 22# 23# Copyright 2004 Sun Microsystems, Inc. All rights reserved. 24# Use is subject to license terms. 25# 26 27# 28#pragma ident "%Z%%M% %I% %E% SMI" 29# 30 31# 32# The officially supported devices do not require a entry under 33# tape-config-list as their configuration is built in to the driver. 34# 35# 36# A non configured drive will say Unconfigured Drive: and have single quoted 37# Vendor and Product strings displayed when it's status is checked with mt. 38# 39# mt -f /dev/rmt/# status 40# Unconfigured Drive: Vendor 'VENDOR ' Product 'A Product ID ' 41# sense key(0x0)= No Additional Sense residual= 0 retries= 0 42# file no= 0 block no= 0 43# 44# If your drive is displayed like this first check to see if a newer version 45# of the st driver has added support for your drive. 46# 47# If your drive is not supported by Sun, check the drive manufacturer's 48# documentation or web site for their recommended configuration strings. 49# 50# To configure a drive not supported by the driver, use the single quoted 51# Vendor and Product strings to create a entry under tape-config-list. 52# 53# A starting point for your st.conf entry can be obtained by reading the 54# current DEFAULT configuration from the driver using mt. 55# 56# mt -f /dev/rmt/# config 57# "SONY SDX-700C", "SONY SDX-700C", "SONYSDX700C"; 58# SONYSDX700C = \ 59# 2,0x12,0,0x1865B,4,0x00,0x00,0x00,0x00,0,120,120,3600,3600,3600,3600,3600; 60# 61# 62# Notes: 63# Any spaces in the Vendor field must be kept so that it is 8 64# characters long. Trailing spaces in the Product field can be removed. 65# 66# To add this configuration information, first uncomment the 67# "tape-config-list=" line, and add the first configuration line 68# immediately afterward. If there is more than one entry in the 69# tape-config-list, all entries but the last must end with a comma. 70# The last entry ends with a semicolon. 71# 72# See the driver.conf(4) man page for general information on the conf 73# file format, and the st(7d) man page for information specific to st.conf. 74# 75# Example: 76#tape-config-list= 77# "VENDOR A Product ID", "A Prettier Name to Display", "A-Config-Name", 78# "VENDORB Other Product ID", "An Other Pretty Name", "Other-Config-Name"; 79# 80# Then for each config-Name there must be a setup string that looks like this. 81# 82# A-Config-Name = \ 83# 2,0x34,0,0x18659,4,0x47,0x47,0x47,0x47,1,120,120,3600,3600,3600,3600,3600; 84# Other-Config-Name = 1,0x3B,0,0x18659,4,0x40,0x40,0x40,0x40,3; 85# 86# For specific details for of values to use see the st(7D) man pages and 87# drive vendor manuals. 88# 89 90 91 92name="st" class="scsi" target=0 lun=0; 93name="st" class="scsi" target=1 lun=0; 94name="st" class="scsi" target=2 lun=0; 95name="st" class="scsi" target=3 lun=0; 96name="st" class="scsi" target=4 lun=0; 97name="st" class="scsi" target=5 lun=0; 98name="st" class="scsi" target=6 lun=0; 99 100# 101# In case there are wide tape drives, one can use these targets 102# 103#name="st" class="scsi" target=8 lun=0; 104#name="st" class="scsi" target=9 lun=0; 105#name="st" class="scsi" target=10 lun=0; 106#name="st" class="scsi" target=11 lun=0; 107#name="st" class="scsi" target=12 lun=0; 108#name="st" class="scsi" target=13 lun=0; 109#name="st" class="scsi" target=14 lun=0; 110#name="st" class="scsi" target=15 lun=0; 111 112# This line adds support for Fibre Channel Tapes 113name="st" parent="fp" target=0; 114