Copyright 1989 AT&T
Copyright (c) 2006, Sun Microsystems, Inc.
The contents of this file are subject to the terms of the Common Development and Distribution License (the "License"). You may not use this file except in compliance with the License.
You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE or http://www.opensolaris.org/os/licensing. See the License for the specific language governing permissions and limitations under the License.
When distributing Covered Code, include this CDDL HEADER in each file and include the License file at usr/src/OPENSOLARIS.LICENSE. If applicable, add the following below this CDDL HEADER, with the fields enclosed by brackets "[]" replaced with your own identifying information: Portions Copyright [yyyy] [name of copyright owner]
#include <sys/stream.h> int testb(size_t size, uint_t pri);
Architecture independent level 1 (DDI/DKI).
size
Size of the requested buffer.
pri
Priority of the allocb request.
The testb() function checks to see if an allocb(9F) call is likely to succeed if a buffer of size bytes at priority pri is requested. Even if testb() returns successfully, the call to allocb(9F) can fail. The pri argument is no longer used, but is retained for compatibility.
Returns 1 if a buffer of the requested size is available, and 0 if one is not.
The testb() function can be called user, interrupt, or kernel context.
Example 1 testb() example
In a service routine, if copymsg(9F) fails (line 6), the message is put back on the queue (line 7) and a routine, tryagain, is scheduled to be run in one tenth of a second. Then the service routine returns.
When the timeout(9F) function runs, if there is no message on the front of the queue, it just returns. Otherwise, for each message block in the first message, check to see if an allocation would succeed. If the number of message blocks equals the number we can allocate, then enable the service procedure. Otherwise, reschedule tryagain to run again in another tenth of a second. Note that tryagain is merely an approximation. Its accounting may be faulty. Consider the case of a message comprised of two 1024-byte message blocks. If there is only one free 1024-byte message block and no free 2048-byte message blocks, then testb() will still succeed twice. If no message blocks are freed of these sizes before the service procedure runs again, then the copymsg(9F) will still fail. The reason testb() is used here is because it is significantly faster than calling copymsg. We must minimize the amount of time spent in a timeout() routine.
1 xxxsrv(q)
2 queue_t *q;
3 {
4 mblk_t *mp;
5 mblk_t *nmp;
. . .
6 if ((nmp = copymsg(mp)) == NULL) {
7 putbq(q, mp);
8 timeout(tryagain, (intptr_t)q, drv_usectohz(100000));
9 return;
10 }
. . .
11 }
12
13 tryagain(q)
14 queue_t *q;
15 {
16 register int can_alloc = 0;
17 register int num_blks = 0;
18 register mblk_t *mp;
19
20 if (!q->q_first)
21 return;
22 for (mp = q->q_first; mp; mp = mp->b_cont) {
23 num_blks++;
24 can_alloc += testb((mp->b_datap->db_lim -
25 mp->b_datap->db_base), BPRI_MED);
26 }
27 if (num_blks == can_alloc)
28 qenable(q);
29 else
30 timeout(tryagain, (intptr_t)q, drv_usectohz(100000));
31 }
allocb(9F), bufcall(9F), copymsg(9F), timeout(9F)
Writing Device Drivers
STREAMS Programming Guide
The pri argument is provided for compatibility only. Its value is ignored.