xref: /illumos-gate/usr/src/uts/sun4u/serengeti/io/sbdp_cpu.c (revision 30f1f754a88aa357235064d8c7ce78f2f546e0aa)
1 /*
2  * CDDL HEADER START
3  *
4  * The contents of this file are subject to the terms of the
5  * Common Development and Distribution License (the "License").
6  * You may not use this file except in compliance with the License.
7  *
8  * You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE
9  * or http://www.opensolaris.org/os/licensing.
10  * See the License for the specific language governing permissions
11  * and limitations under the License.
12  *
13  * When distributing Covered Code, include this CDDL HEADER in each
14  * file and include the License file at usr/src/OPENSOLARIS.LICENSE.
15  * If applicable, add the following below this CDDL HEADER, with the
16  * fields enclosed by brackets "[]" replaced with your own identifying
17  * information: Portions Copyright [yyyy] [name of copyright owner]
18  *
19  * CDDL HEADER END
20  */
21 
22 /*
23  * Copyright 2009 Sun Microsystems, Inc.  All rights reserved.
24  * Use is subject to license terms.
25  * Copyright (c) 2016 by Delphix. All rights reserved.
26  */
27 
28 /*
29  * CPU management for serengeti DR
30  *
31  * There are three states a CPU can be in:
32  *
33  *	disconnected:		In reset
34  *	connect,unconfigured:	Idling in OBP's idle loop
35  *	configured:		Running Solaris
36  *
37  * State transitions:
38  *
39  *                connect              configure
40  *              ------------>         ------------>
41  * disconnected              connected             configured
42  *                          unconfigured
43  *              <-----------         <-------------
44  *                disconnect           unconfigure
45  *
46  * Firmware involvements
47  *
48  *              start_cpu(SC)
49  *      prom_serengeti_wakeupcpu(OBP)
50  *              ------------>         ------------------------->
51  * disconnected              connected                         configured
52  *                          unconfigured
53  *              <-----------          <-------------------------
54  *      prom_serengeti_cpu_off(OBP)  prom_serengeti_cpu_off(OBP)
55  *               stop_cpu(SC)        prom_serengeti_wakeupcpu(OBP)
56  *
57  * SIR (Software Initiated Reset) is used to unconfigure a CPU.
58  * After the CPU has completed flushing the caches, it issues an
59  * sir instruction to put itself through POST.  POST detects that
60  * it is an SIR, and re-enters OBP as a slave.  When the operation
61  * completes successfully, the CPU will be idling in OBP.
62  */
63 
64 #include <sys/obpdefs.h>
65 #include <sys/types.h>
66 #include <sys/cmn_err.h>
67 #include <sys/cpuvar.h>
68 #include <sys/membar.h>
69 #include <sys/x_call.h>
70 #include <sys/machsystm.h>
71 #include <sys/cpu_sgnblk_defs.h>
72 #include <sys/pte.h>
73 #include <vm/hat_sfmmu.h>
74 #include <sys/promif.h>
75 #include <sys/note.h>
76 #include <sys/vmsystm.h>
77 #include <vm/seg_kmem.h>
78 
79 #include <sys/sbd_ioctl.h>
80 #include <sys/sbd.h>
81 #include <sys/sbdp_priv.h>
82 #include <sys/sbdp_mem.h>
83 #include <sys/sbdp_error.h>
84 #include <sys/sgsbbc_iosram.h>
85 #include <sys/prom_plat.h>
86 #include <sys/cheetahregs.h>
87 
88 uint64_t	*sbdp_valp;
89 extern uint64_t	va_to_pa(void *);
90 static int	sbdp_cpu_ntries = 50000;
91 static int	sbdp_cpu_delay = 100;
92 void		sbdp_get_cpu_sram_addr(uint64_t, uint64_t);
93 static int	cpusram_map(caddr_t *, pgcnt_t *);
94 static void	cpusram_unmap(caddr_t *, pgcnt_t);
95 extern int	prom_serengeti_wakeupcpu(pnode_t);
96 extern int	prom_serengeti_cpu_off(pnode_t);
97 extern sbdp_wnode_t *sbdp_get_wnodep(int);
98 extern caddr_t	sbdp_shutdown_va;
99 static int	sbdp_prom_get_cpu(void *arg, int changed);
100 static void	sbdp_cpu_shutdown_self(void);
101 
102 int
103 sbdp_disconnect_cpu(sbdp_handle_t *hp, dev_info_t *dip, processorid_t cpuid)
104 {
105 	pnode_t		nodeid;
106 	int		bd, wnode;
107 	sbdp_wnode_t	*wnodep;
108 	sbdp_bd_t	*bdp = NULL;
109 	int		rv = 0;
110 	processorid_t	cpu = cpuid;
111 	processorid_t	portid;
112 	static fn_t	f = "sbdp_disconnect_cpu";
113 
114 	SBDP_DBG_FUNC("%s\n", f);
115 
116 	nodeid = ddi_get_nodeid(dip);
117 
118 	/*
119 	 * Get board number and node number
120 	 * The check for determining if nodeid is valid is done inside
121 	 * sbdp_get_bd_and_wnode_num.
122 	 */
123 	if (SBDP_INJECT_ERROR(f, 0) ||
124 	    sbdp_get_bd_and_wnode_num(nodeid, &bd, &wnode) != 0) {
125 
126 		rv = -1;
127 		goto out;
128 	}
129 
130 	/*
131 	 * Grab the lock to prevent status threads from accessing
132 	 * registers on the CPU when it is being put into reset.
133 	 */
134 	wnodep = sbdp_get_wnodep(wnode);
135 	bdp = &wnodep->bds[bd];
136 	ASSERT(bdp);
137 	mutex_enter(&bdp->bd_mutex);
138 
139 	/*
140 	 * Mark the CPU in reset.  This should be done before calling
141 	 * the SC because we won't know at which stage it failed if
142 	 * the SC call returns failure.
143 	 */
144 	sbdp_cpu_in_reset(wnode, bd, SG_CPUID_TO_CPU_UNIT(cpuid), 1);
145 
146 	/*
147 	 * Ask OBP to mark the CPU as in POST
148 	 */
149 	if (SBDP_INJECT_ERROR(f, 1) || prom_serengeti_cpu_off(nodeid) != 0) {
150 
151 		rv = -1;
152 		goto out;
153 	}
154 
155 	/*
156 	 * Ask the SC to put the CPU into reset. If the first
157 	 * core is not present, the stop CPU interface needs
158 	 * to be called with the portid rather than the cpuid.
159 	 */
160 	portid = SG_CPUID_TO_PORTID(cpuid);
161 	if (!SBDP_IS_CPU_PRESENT(bdp, SG_CPUID_TO_CPU_UNIT(portid))) {
162 		cpu = portid;
163 	}
164 
165 	if (SBDP_INJECT_ERROR(f, 2) || sbdp_stop_cpu(cpu) != 0) {
166 
167 		rv = -1;
168 		goto out;
169 	}
170 
171 out:
172 	if (bdp != NULL) {
173 		mutex_exit(&bdp->bd_mutex);
174 	}
175 
176 	if (rv != 0) {
177 		sbdp_set_err(hp->h_err, ESGT_STOPCPU, NULL);
178 	}
179 
180 	return (rv);
181 }
182 
183 int
184 sbdp_connect_cpu(sbdp_handle_t *hp, dev_info_t *dip, processorid_t cpuid)
185 {
186 	pnode_t		nodeid;
187 	sbd_error_t	*sep;
188 	int		i;
189 	int		bd, wnode;
190 	int		rv = 0;
191 	static fn_t	f = "sbdp_connect_cpu";
192 
193 	SBDP_DBG_FUNC("%s\n", f);
194 
195 	sep = hp->h_err;
196 
197 	nodeid = ddi_get_nodeid(dip);
198 
199 	/*
200 	 * The check for determining if nodeid is valid is done inside
201 	 * sbdp_get_bd_and_wnode_num.
202 	 */
203 	if (SBDP_INJECT_ERROR(f, 0) ||
204 	    sbdp_get_bd_and_wnode_num(nodeid, &bd, &wnode) != 0) {
205 
206 		rv = -1;
207 		goto out;
208 	}
209 
210 	/*
211 	 * Ask the SC to bring the CPU out of reset.
212 	 * At this point, the sb_dev_present bit is not set for the CPU.
213 	 * From sbd point of view the CPU is not present yet.  No
214 	 * status threads will try to read registers off the CPU.
215 	 * Since we are already holding sb_mutex, it is not necessary
216 	 * to grab the board mutex when checking and setting the
217 	 * cpus_in_reset bit.
218 	 */
219 	if (sbdp_is_cpu_in_reset(wnode, bd, SG_CPUID_TO_CPU_UNIT(cpuid))) {
220 
221 		sbdp_wnode_t	*wnodep;
222 		sbdp_bd_t	*bdp = NULL;
223 		processorid_t	cpu = cpuid;
224 		processorid_t	portid;
225 
226 		wnodep = sbdp_get_wnodep(wnode);
227 		bdp = &wnodep->bds[bd];
228 		ASSERT(bdp);
229 
230 		/*
231 		 * If the first core is not present, the start CPU
232 		 * interface needs to be called with the portid rather
233 		 * than the cpuid.
234 		 */
235 		portid = SG_CPUID_TO_PORTID(cpuid);
236 		if (!SBDP_IS_CPU_PRESENT(bdp, SG_CPUID_TO_CPU_UNIT(portid))) {
237 			cpu = portid;
238 		}
239 
240 		if (SBDP_INJECT_ERROR(f, 1) || sbdp_start_cpu(cpu) != 0) {
241 
242 			rv = -1;
243 			goto out;
244 		}
245 
246 		if (SBDP_INJECT_ERROR(f, 2) ||
247 		    prom_serengeti_wakeupcpu(nodeid) != 0) {
248 
249 			rv = -1;
250 			goto out;
251 		}
252 	}
253 
254 	/*
255 	 * Mark the CPU out of reset.
256 	 */
257 	sbdp_cpu_in_reset(wnode, bd, SG_CPUID_TO_CPU_UNIT(cpuid), 0);
258 
259 	/*
260 	 * Refresh the bd info
261 	 * we need to wait until all cpus are out of reset
262 	 */
263 	for (i = 0; i < SG_MAX_CPUS_PER_BD; i++)
264 		if (sbdp_is_cpu_present(wnode, bd, i) &&
265 		    sbdp_is_cpu_in_reset(wnode, bd, i) == 1) {
266 			break;
267 		}
268 
269 	if (i == SG_MAX_CPUS_PER_BD) {
270 		/*
271 		 * All cpus are out of reset so it is safe to
272 		 * update the bd info
273 		 */
274 		sbdp_add_new_bd_info(wnode, bd);
275 	}
276 
277 out:
278 	if (rv != 0)
279 		sbdp_set_err(sep, ESGT_WAKEUPCPU, NULL);
280 
281 	return (rv);
282 }
283 
284 int
285 sbdp_cpu_poweron(struct cpu *cp)
286 {
287 	int		cpuid;
288 	int		ntries;
289 	pnode_t		nodeid;
290 	extern void	restart_other_cpu(int);
291 	static fn_t	f = "sbdp_cpu_poweron";
292 
293 	SBDP_DBG_FUNC("%s\n", f);
294 
295 	ASSERT(MUTEX_HELD(&cpu_lock));
296 
297 	ntries = sbdp_cpu_ntries;
298 	cpuid = cp->cpu_id;
299 
300 	nodeid = cpunodes[cpuid].nodeid;
301 	ASSERT(nodeid != (pnode_t)0);
302 
303 	/*
304 	 * This is a safe guard in case the CPU has taken a trap
305 	 * and idling in POST.
306 	 */
307 	if (SBDP_INJECT_ERROR(f, 0) ||
308 	    prom_serengeti_wakeupcpu(nodeid) != 0) {
309 
310 		return (EBUSY);
311 	}
312 
313 	cp->cpu_flags &= ~CPU_POWEROFF;
314 
315 	/*
316 	 * NOTE: restart_other_cpu pauses cpus during the
317 	 *	slave cpu start.  This helps to quiesce the
318 	 *	bus traffic a bit which makes the tick sync
319 	 *	routine in the prom more robust.
320 	 */
321 	SBDP_DBG_CPU("%s: COLD START for cpu (%d)\n", f, cpuid);
322 
323 	restart_other_cpu(cpuid);
324 
325 	SBDP_DBG_CPU("after restarting other cpus\n");
326 
327 	/*
328 	 * Wait for the cpu to reach its idle thread before
329 	 * we zap it with a request to blow away the mappings
330 	 * it (might) have for the sbdp_shutdown_asm code
331 	 * it may have executed on unconfigure.
332 	 */
333 	while ((cp->cpu_thread != cp->cpu_idle_thread) && (ntries > 0)) {
334 		DELAY(sbdp_cpu_delay);
335 		ntries--;
336 	}
337 
338 	SBDP_DBG_CPU("%s: waited %d out of %d loops for cpu %d\n",
339 	    f, sbdp_cpu_ntries - ntries, sbdp_cpu_ntries, cpuid);
340 
341 	return (0);
342 }
343 
344 
345 #define	SBDP_CPU_SRAM_ADDR	0x7fff0900000ull
346 #define	SBDP_CPU_SRAM_SIZE	0x20000ull
347 
348 static const char cpyren_key[] = "COPYREN";
349 
350 static uint64_t bbsram_pa;
351 static uint_t bbsram_size;
352 
353 typedef struct {
354 	caddr_t		vaddr;
355 	pgcnt_t		npages;
356 	uint64_t	*pa;
357 	uint_t		*size;
358 } sbdp_cpu_sram_map_t;
359 
360 int
361 sbdp_cpu_poweroff(struct cpu *cp)
362 {
363 	processorid_t	cpuid;
364 	pnode_t		nodeid;
365 	sbdp_cpu_sram_map_t	map;
366 	static fn_t	f = "sbdp_cpu_poweroff";
367 
368 	SBDP_DBG_FUNC("%s\n", f);
369 
370 	ASSERT(MUTEX_HELD(&cpu_lock));
371 
372 	/*
373 	 * Capture all CPUs (except for detaching proc) to prevent
374 	 * crosscalls to the detaching proc until it has cleared its
375 	 * bit in cpu_ready_set.
376 	 */
377 	cpuid = cp->cpu_id;
378 
379 	nodeid = cpunodes[cpuid].nodeid;
380 	ASSERT(nodeid != (pnode_t)0);
381 
382 	*sbdp_valp = 0ull;
383 	/*
384 	 * Do the cpu sram mapping now.  This avoids problems with
385 	 * mutexes and high PILS
386 	 */
387 	if (SBDP_INJECT_ERROR(f, 0) ||
388 	    cpusram_map(&map.vaddr, &map.npages) != DDI_SUCCESS) {
389 		return (EBUSY);
390 	}
391 
392 	map.pa = &bbsram_pa;
393 	map.size = &bbsram_size;
394 
395 	/*
396 	 * Do a cross call to the cpu so it obtains the base address
397 	 */
398 	xc_one(cpuid, sbdp_get_cpu_sram_addr, (uint64_t)&map,
399 	    (uint64_t)NULL);
400 
401 	cpusram_unmap(&map.vaddr, map.npages);
402 
403 	if (SBDP_INJECT_ERROR(f, 1) || bbsram_size == 0) {
404 		cmn_err(CE_WARN, "cpu%d: Key \"%s\" missing from CPU SRAM TOC",
405 		    cpuid, cpyren_key);
406 		return (EBUSY);
407 	}
408 
409 	if ((bbsram_pa & MMU_PAGEOFFSET) != 0) {
410 		cmn_err(CE_WARN, "cpu%d: CPU SRAM key \"%s\" not page aligned, "
411 		    "offset = 0x%lx", cpuid, cpyren_key,
412 		    (bbsram_pa - (uint64_t)SBDP_CPU_SRAM_ADDR));
413 		return (EBUSY);
414 	}
415 
416 	if (bbsram_size < MMU_PAGESIZE) {
417 		cmn_err(CE_WARN, "cpu%d: CPU SRAM key \"%s\" too small, "
418 		    "size = 0x%x", cpuid, cpyren_key, bbsram_size);
419 		return (EBUSY);
420 	}
421 
422 	/*
423 	 * Capture all CPUs (except for detaching proc) to prevent
424 	 * crosscalls to the detaching proc until it has cleared its
425 	 * bit in cpu_ready_set.
426 	 *
427 	 * The CPU's remain paused and the prom_mutex is known to be free.
428 	 * This prevents the x-trap victim from blocking when doing prom
429 	 * IEEE-1275 calls at a high PIL level.
430 	 */
431 
432 	promsafe_pause_cpus();
433 
434 	/*
435 	 * Quiesce interrupts on the target CPU. We do this by setting
436 	 * the CPU 'not ready'- (i.e. removing the CPU from cpu_ready_set) to
437 	 * prevent it from receiving cross calls and cross traps.
438 	 * This prevents the processor from receiving any new soft interrupts.
439 	 */
440 
441 	mp_cpu_quiesce(cp);
442 
443 	/* tell the prom the cpu is going away */
444 	if (SBDP_INJECT_ERROR(f, 2) || prom_serengeti_cpu_off(nodeid) != 0)
445 		return (EBUSY);
446 
447 	/*
448 	 * An sir instruction is issued at the end of the shutdown
449 	 * routine to make the CPU go through POST and re-enter OBP.
450 	 */
451 	xt_one_unchecked(cp->cpu_id, (xcfunc_t *)idle_stop_xcall,
452 	    (uint64_t)sbdp_cpu_shutdown_self, 0);
453 
454 	*sbdp_valp = 3ull;
455 
456 	start_cpus();
457 
458 	/*
459 	 * Wait until we reach the OBP idle loop or time out.
460 	 * prom_serengeti_wakeupcpu waits for up to 60 seconds for the
461 	 * CPU to reach OBP idle loop.
462 	 */
463 	if (SBDP_INJECT_ERROR(f, 3) ||
464 	    prom_serengeti_wakeupcpu(nodeid) != 0) {
465 
466 		/*
467 		 * If it fails here, we still consider the unconfigure
468 		 * operation as successful.
469 		 */
470 		cmn_err(CE_WARN, "cpu%d: CPU failed to enter OBP idle loop.\n",
471 		    cpuid);
472 	}
473 
474 	ASSERT(!(CPU_IN_SET(cpu_ready_set, cpuid)));
475 
476 	bbsram_pa = 0;
477 	bbsram_size = 0;
478 
479 	return (0);
480 }
481 
482 processorid_t
483 sbdp_get_cpuid(sbdp_handle_t *hp, dev_info_t *dip)
484 {
485 	int		cpuid;
486 	char		type[OBP_MAXPROPNAME];
487 	pnode_t		nodeid;
488 	sbd_error_t	*sep;
489 	static fn_t	f = "sbdp_get_cpuid";
490 
491 	SBDP_DBG_FUNC("%s\n", f);
492 
493 	nodeid = ddi_get_nodeid(dip);
494 	if (sbdp_is_node_bad(nodeid))
495 		return (-1);
496 
497 	sep = hp->h_err;
498 
499 	if (prom_getproplen(nodeid, "device_type") < OBP_MAXPROPNAME)
500 		(void) prom_getprop(nodeid, "device_type", (caddr_t)type);
501 	else {
502 		sbdp_set_err(sep, ESGT_NO_DEV_TYPE, NULL);
503 		return (-1);
504 	}
505 
506 	if (strcmp(type, "cpu") != 0) {
507 		sbdp_set_err(sep, ESGT_NOT_CPUTYPE, NULL);
508 		return (-1);
509 	}
510 
511 	/*
512 	 * Check to see if property "cpuid" exists first.
513 	 * If not, check for "portid".
514 	 */
515 	if (prom_getprop(nodeid, "cpuid", (caddr_t)&cpuid) == -1)
516 		if (prom_getprop(nodeid, "portid", (caddr_t)&cpuid) == -1) {
517 
518 			return (-1);
519 	}
520 
521 	return ((processorid_t)cpuid & SG_CPU_ID_MASK);
522 }
523 
524 int
525 sbdp_cpu_get_impl(sbdp_handle_t *hp, dev_info_t *dip)
526 {
527 	int		impl;
528 	char		type[OBP_MAXPROPNAME];
529 	pnode_t		nodeid;
530 	sbd_error_t	*sep;
531 	static fn_t	f = "sbdp_cpu_get_impl";
532 
533 	SBDP_DBG_FUNC("%s\n", f);
534 
535 	nodeid = ddi_get_nodeid(dip);
536 	if (sbdp_is_node_bad(nodeid))
537 		return (-1);
538 
539 	sep = hp->h_err;
540 
541 	if (prom_getproplen(nodeid, "device_type") < OBP_MAXPROPNAME)
542 		(void) prom_getprop(nodeid, "device_type", (caddr_t)type);
543 	else {
544 		sbdp_set_err(sep, ESGT_NO_DEV_TYPE, NULL);
545 		return (-1);
546 	}
547 
548 	if (strcmp(type, "cpu") != 0) {
549 		sbdp_set_err(sep, ESGT_NOT_CPUTYPE, NULL);
550 		return (-1);
551 	}
552 
553 	/*
554 	 * Get the implementation# property.
555 	 */
556 	if (prom_getprop(nodeid, "implementation#", (caddr_t)&impl) == -1)
557 		return (-1);
558 
559 	return (impl);
560 }
561 
562 struct sbdp_prom_get_node_args {
563 	pnode_t node;		/* current node */
564 	processorid_t portid;	/* portid we are looking for */
565 	pnode_t result_node;	/* node found with the above portid */
566 };
567 
568 pnode_t
569 sbdp_find_nearby_cpu_by_portid(pnode_t nodeid, processorid_t portid)
570 {
571 	struct sbdp_prom_get_node_args arg;
572 	static fn_t	f = "sbdp_find_nearby_cpu_by_portid";
573 
574 	SBDP_DBG_FUNC("%s\n", f);
575 
576 	arg.node = nodeid;
577 	arg.portid = portid;
578 	(void) prom_tree_access(sbdp_prom_get_cpu, &arg, NULL);
579 
580 	return (arg.result_node);
581 }
582 
583 /*ARGSUSED*/
584 static int
585 sbdp_prom_get_cpu(void *arg, int changed)
586 {
587 	int	portid;
588 	pnode_t	parent, cur_node;
589 	struct sbdp_prom_get_node_args *argp = arg;
590 	static fn_t	f = "sbdp_prom_get_cpu";
591 
592 	SBDP_DBG_FUNC("%s\n", f);
593 
594 	parent = prom_parentnode(argp->node);
595 
596 	for (cur_node = prom_childnode(parent); cur_node != OBP_NONODE;
597 	    cur_node = prom_nextnode(cur_node)) {
598 
599 		if (prom_getprop(cur_node, OBP_PORTID, (caddr_t)&portid) < 0)
600 			continue;
601 
602 		if ((portid == argp->portid) && (cur_node != argp->node))
603 			break;
604 	}
605 
606 	argp->result_node = cur_node;
607 
608 	return (0);
609 }
610 
611 
612 /*
613  * A detaching CPU is xcalled with an xtrap to sbdp_cpu_stop_self() after
614  * it has been offlined. The function of this routine is to get the cpu
615  * spinning in a safe place. The requirement is that the system will not
616  * reference anything on the detaching board (memory and i/o is detached
617  * elsewhere) and that the CPU not reference anything on any other board
618  * in the system.  This isolation is required during and after the writes
619  * to the domain masks to remove the board from the domain.
620  *
621  * To accomplish this isolation the following is done:
622  *	0) Map the CPUSRAM to obtain the correct address in SRAM
623  *      1) Create a locked mapping to a location in CPU SRAM where
624  *      the cpu will execute.
625  *      2) Copy the target function (sbdp_shutdown_asm) in which
626  *      the cpu will execute into CPU SRAM.
627  *      3) Jump into function with CPU SRAM.
628  *      Function will:
629  *      3.1) Flush its Ecache (displacement).
630  *      3.2) Flush its Dcache with HW mechanism.
631  *      3.3) Flush its Icache with HW mechanism.
632  *      3.4) Flush all valid and _unlocked_ D-TLB entries.
633  *      3.5) Flush all valid and _unlocked_ I-TLB entries.
634  *      4) Jump into a tight loop.
635  */
636 
637 static void
638 sbdp_cpu_stop_self(uint64_t pa)
639 {
640 	cpu_t		*cp = CPU;
641 	int		cpuid = cp->cpu_id;
642 	tte_t		tte;
643 	volatile uint_t	*src, *dst;
644 	size_t		funclen;
645 	sbdp_shutdown_t	sht;
646 	uint_t		bbsram_pfn;
647 	uint64_t	bbsram_addr;
648 	void		(*bbsram_func)(sbdp_shutdown_t *);
649 	extern void	sbdp_shutdown_asm(sbdp_shutdown_t *);
650 	extern void	sbdp_shutdown_asm_end(void);
651 
652 	funclen = (uintptr_t)sbdp_shutdown_asm_end -
653 	    (uintptr_t)sbdp_shutdown_asm;
654 	ASSERT(funclen <= MMU_PAGESIZE);
655 	ASSERT(bbsram_pa != 0);
656 	ASSERT((bbsram_pa & MMU_PAGEOFFSET) == 0);
657 	ASSERT(bbsram_size >= MMU_PAGESIZE);
658 
659 	stdphys(pa, 3);
660 	bbsram_pfn = (uint_t)(bbsram_pa >> MMU_PAGESHIFT);
661 
662 	bbsram_addr = (uint64_t)sbdp_shutdown_va;
663 	sht.estack = bbsram_addr + MMU_PAGESIZE;
664 	sht.flushaddr = ecache_flushaddr;
665 
666 	tte.tte_inthi = TTE_VALID_INT | TTE_SZ_INT(TTE8K) |
667 	    TTE_PFN_INTHI(bbsram_pfn);
668 	tte.tte_intlo = TTE_PFN_INTLO(bbsram_pfn) |
669 	    TTE_HWWR_INT | TTE_PRIV_INT | TTE_LCK_INT;
670 	sfmmu_dtlb_ld_kva(sbdp_shutdown_va, &tte); /* load dtlb */
671 	sfmmu_itlb_ld_kva(sbdp_shutdown_va, &tte); /* load itlb */
672 
673 	for (src = (uint_t *)sbdp_shutdown_asm, dst = (uint_t *)bbsram_addr;
674 	    src < (uint_t *)sbdp_shutdown_asm_end; src++, dst++)
675 	*dst = *src;
676 
677 	bbsram_func = (void (*)())bbsram_addr;
678 	sht.size = (uint32_t)cpunodes[cpuid].ecache_size << 1;
679 	sht.linesize = (uint32_t)cpunodes[cpuid].ecache_linesize;
680 	sht.physaddr = pa;
681 
682 	/*
683 	 * Signal to sbdp_cpu_poweroff() that we're just
684 	 * about done.
685 	 */
686 	cp->cpu_m.in_prom = 1;
687 
688 	stdphys(pa, 4);
689 	(*bbsram_func)(&sht);
690 }
691 
692 /* ARGSUSED */
693 void
694 sbdp_get_cpu_sram_addr(uint64_t arg1, uint64_t arg2)
695 {
696 	uint64_t	*pap;
697 	uint_t		*sizep;
698 	struct iosram_toc *tocp;
699 	uint_t		offset;
700 	uint_t		size;
701 	sbdp_cpu_sram_map_t *map;
702 	int		i;
703 	fn_t		f = "sbdp_get_cpu_sram_addr";
704 
705 	SBDP_DBG_FUNC("%s\n", f);
706 
707 	map = (sbdp_cpu_sram_map_t *)arg1;
708 	tocp = (struct iosram_toc *)map->vaddr;
709 	pap = map->pa;
710 	sizep = map->size;
711 
712 	for (i = 0; i < tocp->iosram_tagno; i++) {
713 		if (strcmp(tocp->iosram_keys[i].key, cpyren_key) == 0)
714 			break;
715 	}
716 	if (i == tocp->iosram_tagno) {
717 		*pap = 0;
718 		*sizep = 0;
719 		return;
720 	}
721 	offset = tocp->iosram_keys[i].offset;
722 	size = tocp->iosram_keys[i].size;
723 
724 	/*
725 	 * The address we want is the begining of cpusram + offset
726 	 */
727 	*pap = SBDP_CPU_SRAM_ADDR + offset;
728 
729 	*sizep = size;
730 }
731 
732 static int
733 cpusram_map(caddr_t *vaddrp, pgcnt_t *npp)
734 {
735 	uint_t		pgoffset;
736 	pgcnt_t		npages;
737 	pfn_t		pfn;
738 	uint64_t	base;
739 	caddr_t		kaddr;
740 	uint_t		mapping_attr;
741 
742 	base = (uint64_t)SBDP_CPU_SRAM_ADDR & (~MMU_PAGEOFFSET);
743 	pfn = mmu_btop(base);
744 
745 	/*
746 	 * Do a quick sanity check to make sure we are in I/O space.
747 	 */
748 	if (pf_is_memory(pfn))
749 		return (DDI_FAILURE);
750 
751 	pgoffset = (ulong_t)SBDP_CPU_SRAM_ADDR & MMU_PAGEOFFSET;
752 	npages = mmu_btopr(SBDP_CPU_SRAM_SIZE + pgoffset);
753 
754 	kaddr = vmem_alloc(heap_arena, ptob(npages), VM_NOSLEEP);
755 	if (kaddr == NULL)
756 		return (DDI_ME_NORESOURCES);
757 
758 	mapping_attr = PROT_READ;
759 	/*
760 	 * Now map in the pages we've allocated...
761 	 */
762 	hat_devload(kas.a_hat, kaddr, ptob(npages), pfn, mapping_attr,
763 	    HAT_LOAD_LOCK);
764 
765 	*vaddrp = kaddr + pgoffset;
766 	*npp = npages;
767 
768 	return (DDI_SUCCESS);
769 }
770 
771 static void
772 cpusram_unmap(caddr_t *vaddrp, pgcnt_t npages)
773 {
774 	uint_t  pgoffset;
775 	caddr_t base;
776 	caddr_t addr = *vaddrp;
777 
778 
779 	pgoffset = (ulong_t)SBDP_CPU_SRAM_ADDR & MMU_PAGEOFFSET;
780 	base = addr - pgoffset;
781 	hat_unload(kas.a_hat, base, ptob(npages), HAT_UNLOAD_UNLOCK);
782 	vmem_free(heap_arena, base, ptob(npages));
783 
784 	*vaddrp = 0;
785 }
786 
787 
788 static void
789 sbdp_cpu_shutdown_self(void)
790 {
791 	cpu_t		*cp = CPU;
792 	int		cpuid = cp->cpu_id;
793 	extern void	flush_windows(void);
794 	uint64_t	pa = va_to_pa((void *)sbdp_valp);
795 
796 	stdphys(pa, 8);
797 	flush_windows();
798 
799 	(void) spl8();
800 
801 	stdphys(pa, 6);
802 
803 	ASSERT(cp->cpu_intr_actv == 0);
804 	ASSERT(cp->cpu_thread == cp->cpu_idle_thread ||
805 	    cp->cpu_thread == cp->cpu_startup_thread);
806 
807 	cp->cpu_flags = CPU_OFFLINE | CPU_QUIESCED | CPU_POWEROFF;
808 
809 	CPU_SIGNATURE(OS_SIG, SIGST_DETACHED, SIGSUBST_NULL, cpuid);
810 
811 	stdphys(pa, 7);
812 	sbdp_cpu_stop_self(pa);
813 
814 	cmn_err(CE_PANIC, "sbdp_cpu_shutdown_self: CPU %d FAILED TO SHUTDOWN",
815 	    cpuid);
816 }
817 
818 typedef struct {
819 	int	node;
820 	int	board;
821 	int 	non_panther_cpus;
822 } sbdp_node_walk_t;
823 
824 static int
825 sbdp_find_non_panther_cpus(dev_info_t *dip, void *node_args)
826 {
827 	int	impl, cpuid, portid;
828 	int	buflen;
829 	char	buf[OBP_MAXPROPNAME];
830 	sbdp_node_walk_t *args = (sbdp_node_walk_t *)node_args;
831 
832 	if (ddi_getlongprop_buf(DDI_DEV_T_ANY, dip,
833 	    DDI_PROP_DONTPASS, OBP_DEVICETYPE, (caddr_t)buf,
834 	    &buflen) != DDI_PROP_SUCCESS) {
835 		return (DDI_WALK_CONTINUE);
836 	}
837 
838 	if (strcmp(buf, "cpu") != 0) {
839 		return (DDI_WALK_CONTINUE);
840 	}
841 
842 	if ((impl = ddi_getprop(DDI_DEV_T_ANY, dip,
843 	    DDI_PROP_DONTPASS, "implementation#", -1)) == -1) {
844 		return (DDI_WALK_CONTINUE);
845 	}
846 
847 	if ((cpuid = ddi_getprop(DDI_DEV_T_ANY, dip,
848 	    DDI_PROP_DONTPASS, "cpuid", -1)) == -1) {
849 		return (DDI_WALK_CONTINUE);
850 	}
851 
852 	portid = SG_CPUID_TO_PORTID(cpuid);
853 
854 	/* filter out nodes not on this board */
855 	if (SG_PORTID_TO_BOARD_NUM(portid) != args->board ||
856 	    SG_PORTID_TO_NODEID(portid) != args->node) {
857 		return (DDI_WALK_PRUNECHILD);
858 	}
859 
860 	switch (impl) {
861 	case CHEETAH_IMPL:
862 	case CHEETAH_PLUS_IMPL:
863 	case JAGUAR_IMPL:
864 		args->non_panther_cpus++;
865 		break;
866 	case PANTHER_IMPL:
867 		break;
868 	default:
869 		ASSERT(0);
870 		args->non_panther_cpus++;
871 		break;
872 	}
873 
874 	SBDP_DBG_CPU("cpuid=0x%x, portid=0x%x, impl=0x%x, device_type=%s",
875 	    cpuid, portid, impl, buf);
876 
877 	return (DDI_WALK_CONTINUE);
878 }
879 
880 int
881 sbdp_board_non_panther_cpus(int node, int board)
882 {
883 	sbdp_node_walk_t arg = {0};
884 
885 	arg.node = node;
886 	arg.board = board;
887 
888 	/*
889 	 * Root node doesn't have to be held.
890 	 */
891 	ddi_walk_devs(ddi_root_node(), sbdp_find_non_panther_cpus,
892 	    (void *)&arg);
893 
894 	return (arg.non_panther_cpus);
895 }
896