1 /* 2 * CDDL HEADER START 3 * 4 * The contents of this file are subject to the terms of the 5 * Common Development and Distribution License (the "License"). 6 * You may not use this file except in compliance with the License. 7 * 8 * You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE 9 * or http://www.opensolaris.org/os/licensing. 10 * See the License for the specific language governing permissions 11 * and limitations under the License. 12 * 13 * When distributing Covered Code, include this CDDL HEADER in each 14 * file and include the License file at usr/src/OPENSOLARIS.LICENSE. 15 * If applicable, add the following below this CDDL HEADER, with the 16 * fields enclosed by brackets "[]" replaced with your own identifying 17 * information: Portions Copyright [yyyy] [name of copyright owner] 18 * 19 * CDDL HEADER END 20 */ 21 /* 22 * Copyright 2009 Sun Microsystems, Inc. All rights reserved. 23 * Use is subject to license terms. 24 * Copyright (c) 2016 by Delphix. All rights reserved. 25 */ 26 27 /* 28 * Asynchronous protocol handler for Z8530 chips 29 * Handles normal UNIX support for terminals & modems 30 */ 31 32 #include <sys/types.h> 33 #include <sys/param.h> 34 #include <sys/systm.h> 35 #include <sys/sysmacros.h> 36 #include <sys/signal.h> 37 #include <sys/kmem.h> 38 #include <sys/termios.h> 39 #include <sys/stropts.h> 40 #include <sys/stream.h> 41 #include <sys/strsun.h> 42 #include <sys/tty.h> 43 #include <sys/ptyvar.h> 44 #include <sys/cred.h> 45 #include <sys/user.h> 46 #include <sys/proc.h> 47 #include <sys/file.h> 48 #include <sys/uio.h> 49 #include <sys/buf.h> 50 #include <sys/mkdev.h> 51 #include <sys/cmn_err.h> 52 #include <sys/strtty.h> 53 #include <sys/consdev.h> 54 #include <sys/zsdev.h> 55 #include <sys/ser_async.h> 56 #include <sys/debug.h> 57 #include <sys/kbio.h> 58 #include <sys/conf.h> 59 #include <sys/ddi.h> 60 #include <sys/sunddi.h> 61 #include <sys/promif.h> 62 #include <sys/policy.h> 63 64 /* 65 * PPS (Pulse Per Second) support. 66 */ 67 extern void ddi_hardpps(struct timeval *, int); 68 static struct ppsclockev ppsclockev; 69 70 #ifdef PPSCLOCKLED 71 /* XXX Use these to observe PPS latencies and jitter on a scope */ 72 #define LED_ON 73 #define LED_OFF 74 #else 75 #define LED_ON 76 #define LED_OFF 77 #endif 78 79 #define ZSA_RCV_SIZE 64 80 #define ZA_KICK_RCV_COUNT 3 81 #define ZSA_GRACE_MIN_FLOW_CONTROL 5 82 #define ZSA_GRACE_MAX_FLOW_CONTROL 20 83 84 int zsasoftdtr = 0; /* if nonzero, softcarrier raises dtr at attach */ 85 int zsb134_weird = 0; /* if set, old weird B134 behavior */ 86 int g_zsticks = 0; /* if set, becomes the global zsticks value */ 87 int g_nocluster = 0; /* if set, disables clustering of received data */ 88 89 unsigned int zsa_rstandby = ZSA_MIN_RSTANDBY; 90 unsigned int zsa_rdone = ZSA_RDONE_MIN; 91 unsigned int zsa_grace_flow_control = ZSA_GRACE_MIN_FLOW_CONTROL; 92 93 94 #define NSPEED 18 /* max # of speeds */ 95 ushort_t zs_speeds[NSPEED] = { 96 0, 97 ZSPEED(50), /* 1 */ 98 ZSPEED(75), /* 2 */ 99 ZSPEED(110), /* 3 */ 100 #ifdef lint 101 ZSPEED(134), /* 4 */ 102 #else 103 ZSPEED(269/2), /* XXX - This is sleazy */ 104 #endif 105 ZSPEED(150), /* 5 */ 106 ZSPEED(200), /* 6 */ 107 ZSPEED(300), /* 7 */ 108 ZSPEED(600), /* 8 */ 109 ZSPEED(1200), /* 9 */ 110 ZSPEED(1800), /* 10 */ 111 ZSPEED(2400), /* 11 */ 112 ZSPEED(4800), /* 12 */ 113 ZSPEED(9600), /* 13 */ 114 ZSPEED(19200), /* 14 */ 115 ZSPEED(38400), /* 15 */ 116 ZSPEED(57680), /* 16 */ 117 ZSPEED(76800) /* 17 */ 118 }; 119 120 ushort_t zsticks[NSPEED] = { 121 3, /* 0 */ 122 3, /* 1 */ 123 3, /* 2 */ 124 3, /* 3 */ 125 3, /* 4 */ 126 3, /* 5 */ 127 3, /* 6 */ 128 3, /* 7 */ 129 3, /* 8 */ 130 3, /* 9 */ 131 3, /* 10 */ 132 3, /* 11 */ 133 3, /* 12 */ 134 3, /* 13 */ 135 2, /* 14 */ 136 1, /* 15 */ 137 1, /* 16 */ 138 1 /* 17 */ 139 }; 140 141 #define ztdelay(nsp) (zsdelay[(nsp)]*(hz/100)) 142 143 ushort_t zsdelay[NSPEED] = { 144 0, 145 ZDELAY(50), /* 1 */ 146 ZDELAY(75), /* 2 */ 147 ZDELAY(110), /* 3 */ 148 #ifdef lint 149 ZDELAY(134), /* 4 */ 150 #else 151 ZDELAY(269/2), 152 #endif 153 ZDELAY(150), /* 5 */ 154 ZDELAY(200), /* 6 */ 155 ZDELAY(300), /* 7 */ 156 ZDELAY(600), /* 8 */ 157 ZDELAY(1200), /* 9 */ 158 ZDELAY(1800), /* 10 */ 159 ZDELAY(2400), /* 11 */ 160 ZDELAY(4800), /* 12 */ 161 ZDELAY(9600), /* 13 */ 162 ZDELAY(19200), /* 14 */ 163 ZDELAY(38400), /* 15 */ 164 ZDELAY(57600), /* 16 */ 165 ZDELAY(76800) /* 17 */ 166 }; 167 168 ushort_t zslowat[NSPEED] = { 169 3, /* 0 */ 170 3, /* 1 */ 171 3, /* 2 */ 172 3, /* 3 */ 173 3, /* 4 */ 174 3, /* 5 */ 175 3, /* 6 */ 176 2, /* 7 */ 177 2, /* 8 */ 178 2, /* 9 */ 179 2, /* 10 */ 180 1, /* 11 */ 181 1, /* 12 */ 182 1, /* 13 */ 183 1, /* 14 */ 184 1, /* 15 */ 185 1, /* 16 */ 186 1 /* 17 */ 187 }; 188 189 ushort_t zshiwat[NSPEED] = { 190 0, /* 0 */ 191 1, /* 1 */ 192 1, /* 2 */ 193 1, /* 3 */ 194 1, /* 4 */ 195 1, /* 5 */ 196 1, /* 6 */ 197 1, /* 7 */ 198 1, /* 8 */ 199 1, /* 9 */ 200 1, /* 10 */ 201 1, /* 11 */ 202 1, /* 12 */ 203 3, /* 13 */ 204 3, /* 14 */ 205 4, /* 15 */ 206 4, /* 16 */ 207 4 /* 17 */ 208 }; 209 210 #define SLAVIO_BUG /* this workaround required to fix bug 1102778 */ 211 212 #define SPEED(cflag) \ 213 ((cflag) & CBAUDEXT) ? \ 214 (((cflag) & 0x1) + CBAUD + 1) : ((cflag) & CBAUD) 215 216 /* 217 * Special macros to handle STREAMS operations. 218 * These are required to address memory leakage problems. 219 * WARNING : the macro do NOT call ZSSETSOFT 220 */ 221 222 /* 223 * Should be called holding only the adaptive (zs_excl) mutex. 224 */ 225 #define ZSA_GETBLOCK(zs, allocbcount) \ 226 { \ 227 register int n = zsa_rstandby; \ 228 while (--n >= 0 && allocbcount > 0) { \ 229 if (!za->za_rstandby[n]) { \ 230 if ((za->za_rstandby[n] = allocb(ZSA_RCV_SIZE, \ 231 BPRI_MED)) == NULL) { \ 232 if (za->za_bufcid == 0) { \ 233 za->za_bufcid = bufcall(ZSA_RCV_SIZE, \ 234 BPRI_MED, \ 235 zsa_callback, zs); \ 236 break; \ 237 } \ 238 } \ 239 allocbcount--; \ 240 } \ 241 } \ 242 if (za->za_ttycommon.t_cflag & CRTSXOFF) { \ 243 mutex_enter(zs->zs_excl_hi); \ 244 if (!(zs->zs_wreg[5] & ZSWR5_RTS)) { \ 245 register int usedcnt = 0; \ 246 for (n = 0; n < zsa_rstandby; n++) \ 247 if (!za->za_rstandby[n]) \ 248 usedcnt++; \ 249 if ((ushort_t)usedcnt <= \ 250 zslowat[SPEED(za->za_ttycommon.t_cflag)]) \ 251 SCC_BIS(5, ZSWR5_RTS); \ 252 } \ 253 mutex_exit(zs->zs_excl_hi); \ 254 } \ 255 } 256 257 /* 258 * Should be called holding the spin (zs_excl_hi) mutex. 259 */ 260 #define ZSA_ALLOCB(mp) \ 261 { \ 262 register int n = zsa_rstandby; \ 263 while (--n >= 0) { \ 264 if ((mp = za->za_rstandby[n]) != NULL) { \ 265 za->za_rstandby[n] = NULL; \ 266 break; \ 267 } \ 268 } \ 269 if (za->za_ttycommon.t_cflag & CRTSXOFF) { \ 270 if (!mp) { \ 271 if (zs->zs_wreg[5] & ZSWR5_RTS) \ 272 SCC_BIC(5, ZSWR5_RTS); \ 273 cmn_err(CE_WARN, "zs%d: message lost\n", \ 274 UNIT(za->za_dev)); \ 275 } else if (zs->zs_wreg[5] & ZSWR5_RTS) { \ 276 register int usedcnt = 0; \ 277 for (n = 0; n < zsa_rstandby; n++) \ 278 if (!za->za_rstandby[n]) \ 279 usedcnt++; \ 280 if ((ushort_t)usedcnt >= (zsa_rstandby - \ 281 zshiwat[SPEED(za->za_ttycommon.t_cflag)])) \ 282 SCC_BIC(5, ZSWR5_RTS); \ 283 } \ 284 } \ 285 } 286 287 /* 288 * Should get the spin (zs_excl_hi) mutex. 289 */ 290 #define ZSA_QREPLY(q, mp) \ 291 { \ 292 mutex_enter(zs->zs_excl_hi); \ 293 ZSA_PUTQ(mp); \ 294 ZSSETSOFT(zs); \ 295 mutex_exit(zs->zs_excl_hi); \ 296 } 297 298 /* 299 * Should be called holding the spin (zs_excl_hi) mutex. 300 */ 301 #define ZSA_PUTQ(mp) \ 302 { \ 303 register int wptr, rptr; \ 304 wptr = za->za_rdone_wptr; \ 305 rptr = za->za_rdone_rptr; \ 306 za->za_rdone[wptr] = mp; \ 307 if ((wptr)+1 == zsa_rdone) { \ 308 za->za_rdone_wptr = wptr = 0; \ 309 } else \ 310 za->za_rdone_wptr = ++wptr; \ 311 if (wptr == rptr) { \ 312 SCC_BIC(1, ZSWR1_INIT); \ 313 cmn_err(CE_WARN, "zs%d disabled: input buffer overflow", \ 314 UNIT(za->za_dev)); \ 315 } \ 316 } 317 318 /* 319 * Should be called holding the spin (zs_excl_hi) mutex. 320 */ 321 #define ZSA_KICK_RCV \ 322 { \ 323 register mblk_t *mp = za->za_rcvblk; \ 324 if (mp) { \ 325 if (zs->zs_rd_cur) { /* M_DATA */ \ 326 mp->b_wptr = zs->zs_rd_cur; \ 327 zs->zs_rd_cur = NULL; \ 328 zs->zs_rd_lim = NULL; \ 329 } \ 330 za->za_rcvblk = NULL; \ 331 ZSA_PUTQ(mp); \ 332 ZSSETSOFT(zs); \ 333 } \ 334 } 335 336 #define ZSA_SEEQ(mp) \ 337 { \ 338 if (za->za_rdone_rptr != za->za_rdone_wptr) { \ 339 mp = za->za_rdone[za->za_rdone_rptr]; \ 340 } else { \ 341 mp = NULL; \ 342 } \ 343 } 344 345 346 /* 347 * Should be called holding only the adaptive (zs_excl) mutex. 348 */ 349 #define ZSA_GETQ(mp) \ 350 { \ 351 if (za->za_rdone_rptr != za->za_rdone_wptr) { \ 352 mp = za->za_rdone[za->za_rdone_rptr]; \ 353 za->za_rdone[za->za_rdone_rptr++] = NULL; \ 354 if (za->za_rdone_rptr == zsa_rdone) \ 355 za->za_rdone_rptr = 0; \ 356 } else { \ 357 mp = NULL; \ 358 } \ 359 } 360 361 /* 362 * Should be called holding only the adaptive (zs_excl) mutex. 363 */ 364 #define ZSA_FLUSHQ \ 365 { \ 366 register mblk_t *tmp; \ 367 for (;;) { \ 368 ZSA_GETQ(tmp); \ 369 if (!(tmp)) \ 370 break; \ 371 freemsg(tmp); \ 372 } \ 373 } 374 375 376 /* 377 * Logging definitions 378 */ 379 380 #ifdef ZSA_DEBUG 381 382 #ifdef ZS_DEBUG_ALL 383 384 extern char zs_h_log[]; 385 extern int zs_h_log_n; 386 387 #define zsa_h_log_clear 388 389 #define zsa_h_log_add(c) \ 390 { \ 391 if (zs_h_log_n >= ZS_H_LOG_MAX) \ 392 zs_h_log_n = 0; \ 393 zs_h_log[zs_h_log_n++] = 'A' + zs->zs_unit; \ 394 zs_h_log[zs_h_log_n++] = c; \ 395 zs_h_log[zs_h_log_n] = '\0'; \ 396 } 397 398 #else /* ZS_DEBUG_ALL */ 399 400 #define ZSA_H_LOG_MAX 0x4000 401 char zsa_h_log[40][ZSA_H_LOG_MAX +10]; 402 int zsa_h_log_n[40]; 403 404 #define zsa_h_log_add(c) \ 405 { \ 406 if (zsa_h_log_n[zs->zs_unit] >= ZSA_H_LOG_MAX) \ 407 zsa_h_log_n[zs->zs_unit] = 0; \ 408 zsa_h_log[zs->zs_unit][zsa_h_log_n[zs->zs_unit]++] = c; \ 409 zsa_h_log[zs->zs_unit][zsa_h_log_n[zs->zs_unit]] = '\0'; \ 410 } 411 412 #define zsa_h_log_clear \ 413 { \ 414 register char *p; \ 415 for (p = &zsa_h_log[zs->zs_unit][ZSA_H_LOG_MAX]; \ 416 p >= &zsa_h_log[zs->zs_unit][0]; /* null */) \ 417 *p-- = '\0'; \ 418 zsa_h_log_n[zs->zs_unit] = 0; \ 419 } 420 421 #endif /* ZS_DEBUG_ALL */ 422 423 #define ZSA_R0_LOG(r0) \ 424 { \ 425 if (r0 & ZSRR0_RX_READY) zsa_h_log_add('R'); \ 426 if (r0 & ZSRR0_TIMER) zsa_h_log_add('Z'); \ 427 if (r0 & ZSRR0_TX_READY) zsa_h_log_add('T'); \ 428 if (r0 & ZSRR0_CD) zsa_h_log_add('D'); \ 429 if (r0 & ZSRR0_SYNC) zsa_h_log_add('S'); \ 430 if (r0 & ZSRR0_CTS) zsa_h_log_add('C'); \ 431 if (r0 & ZSRR0_TXUNDER) zsa_h_log_add('U'); \ 432 if (r0 & ZSRR0_BREAK) zsa_h_log_add('B'); \ 433 } 434 435 #else /* ZSA_DEBUG */ 436 437 #define zsa_h_log_clear 438 #define zsa_h_log_add(c) 439 #define ZSA_R0_LOG(r0) 440 441 #endif /* ZSA_DEBUG */ 442 443 444 445 static int zsa_open(queue_t *rq, dev_t *dev, int flag, int sflag, cred_t *cr); 446 static int zsa_close(queue_t *q, int flag); 447 static void zsa_wput(queue_t *q, mblk_t *mp); 448 static void zsa_rsrv(queue_t *q); 449 450 static struct module_info asyncm_info = { 451 0, 452 "zs", 453 0, 454 INFPSZ, 455 2048, 456 128 457 }; 458 459 static struct qinit async_rinit = { 460 putq, 461 (int (*)())zsa_rsrv, 462 zsa_open, 463 zsa_close, 464 NULL, 465 &asyncm_info, 466 NULL 467 }; 468 469 static struct qinit async_winit = { 470 (int (*)())zsa_wput, 471 NULL, 472 NULL, 473 NULL, 474 NULL, 475 &asyncm_info, 476 NULL 477 }; 478 479 struct streamtab asynctab = { 480 &async_rinit, 481 &async_winit, 482 NULL, 483 NULL, 484 }; 485 486 /* 487 * The async interrupt entry points. 488 */ 489 static void zsa_txint(struct zscom *zs); 490 static void zsa_xsint(struct zscom *zs); 491 static void zsa_rxint(struct zscom *zs); 492 static void zsa_srint(struct zscom *zs); 493 static int zsa_softint(struct zscom *zs); 494 static int zsa_suspend(struct zscom *zs); 495 static int zsa_resume(struct zscom *zs); 496 497 static void 498 zsa_null(struct zscom *zs) 499 { 500 /* LINTED */ 501 register short c; 502 503 SCC_WRITE0(ZSWR0_RESET_TXINT); 504 SCC_WRITE0(ZSWR0_RESET_STATUS); 505 c = SCC_READDATA(); 506 ZSDELAY(); 507 SCC_WRITE0(ZSWR0_RESET_ERRORS); 508 } 509 510 /*ARGSUSED*/ 511 static int 512 zsa_null_int(struct zscom *zs) 513 { 514 return (0); 515 } 516 517 struct zsops zsops_null_async = { 518 zsa_null, 519 zsa_null, 520 zsa_null, 521 zsa_null, 522 zsa_null_int, 523 zsa_null_int, 524 zsa_null_int 525 }; 526 527 struct zsops zsops_async = { 528 zsa_txint, 529 zsa_xsint, 530 zsa_rxint, 531 zsa_srint, 532 zsa_softint, 533 zsa_suspend, 534 zsa_resume 535 }; 536 537 static int dmtozs(int bits); 538 static int zstodm(int bits); 539 static void zsa_restart(void *); 540 static void zsa_reioctl(void *); 541 static void zsa_ioctl(struct asyncline *za, queue_t *q, mblk_t *mp); 542 static void zsa_program(struct asyncline *za, int setibaud); 543 static void zsa_start(struct zscom *zs); 544 static void zsa_kick_rcv(void *); 545 static void zsa_callback(void *); 546 static void zsa_set_za_rcv_flags_mask(struct asyncline *za); 547 int zsgetspeed(dev_t dev); 548 549 static boolean_t abort_charseq_recognize(uchar_t ch); 550 551 /* ARGSUSED */ 552 int 553 zsc_info(dev_info_t *dip, ddi_info_cmd_t infocmd, void *arg, 554 void **result) 555 { 556 register dev_t dev = (dev_t)arg; 557 register int unit, error; 558 register struct zscom *zs; 559 560 if ((unit = UNIT(dev)) >= nzs) 561 return (DDI_FAILURE); 562 563 switch (infocmd) { 564 case DDI_INFO_DEVT2DEVINFO: 565 zs = &zscom[unit]; 566 *result = zs->zs_dip; 567 error = DDI_SUCCESS; 568 break; 569 case DDI_INFO_DEVT2INSTANCE: 570 *result = (void *)(uintptr_t)(unit / 2); 571 error = DDI_SUCCESS; 572 break; 573 default: 574 error = DDI_FAILURE; 575 } 576 return (error); 577 } 578 579 /* 580 * The Asynchronous Driver. 581 */ 582 583 /* 584 * Determine if the zsminor device is in use as either a stdin or stdout 585 * device, so we can be careful about how we initialize the DUART, if 586 * it is, in fact, in use. 587 * 588 * Since this is expensive, we do it once and store away the answers, 589 * since this gets called a number of times per phyical zs device. 590 * Perhaps, this should be in a loadable module, so it can get thrown 591 * away after all the zs devices are attached? 592 */ 593 594 /* 595 * To determine if a given unit is being used by the PROM, 596 * we need to map stdin/stdout devices as known to the PROM 597 * to zs internal minor device numbers: 598 * 599 * PROM (real device) zs minor device 600 * 601 * "zs", 0, "a" 0 ttya 602 * "zs", 0, "b" 1 ttyb 603 * "zs", 1, "a" 2 keyboard 604 * "zs", 1, "b" 3 mouse 605 * "zs", 2, "a" 4 ttyc 606 * "zs", 2, "b" 5 ttyd 607 * 608 * The following value mapping lines assume that insource 609 * and outsink map as "screen, a, b, c, d, ...", and that 610 * zs minors are "a, b, kbd, mouse, c, d, ...". 611 */ 612 613 static int zsa_inuse; /* Strictly for debugging */ 614 615 int 616 zsa_channel_is_active_in_rom(dev_info_t *dev, int zsminor) 617 { 618 char pathname[OBP_MAXPATHLEN]; 619 char default_pathname[OBP_MAXPATHLEN]; 620 char *stdioname; 621 char minordata[3]; 622 623 /* 624 * Basically, get my name and compare it to stdio devnames 625 * and if we get a match, then the device is in use as either 626 * stdin or stdout device (console tip line or keyboard device). 627 * 628 * We get two forms of the pathname, one complete with the 629 * the channel number, and if the channel is 'a', then 630 * we also deal with the user's ability to default to 631 * channel 'a', by omitting the channel number option. 632 * We then compare these pathnames to both the stdin and 633 * stdout pathnames. If any of these match, then the channel 634 * is in use. 635 */ 636 637 (void) ddi_pathname(dev, pathname); /* device pathname */ 638 default_pathname[0] = (char)0; /* default pathname if channel 'a' */ 639 if ((zsminor & 1) == 0) 640 (void) strcpy(default_pathname, pathname); 641 minordata[0] = ':'; 642 minordata[1] = (char)('a' + (zsminor & 1)); 643 minordata[2] = (char)0; 644 (void) strcat(pathname, minordata); 645 646 stdioname = prom_stdinpath(); 647 if (strcmp(pathname, stdioname) == 0) { 648 zsa_inuse |= (1 << zsminor); 649 return (1); 650 } 651 if (strcmp(default_pathname, stdioname) == 0) { 652 zsa_inuse |= (1 << zsminor); 653 return (1); 654 } 655 656 stdioname = prom_stdoutpath(); 657 if (strcmp(pathname, stdioname) == 0) { 658 zsa_inuse |= (1 << zsminor); 659 return (1); 660 } 661 if (strcmp(default_pathname, stdioname) == 0) { 662 zsa_inuse |= (1 << zsminor); 663 return (1); 664 } 665 666 return (0); 667 } 668 669 /* 670 * Initialize zs 671 */ 672 void 673 zsa_init(struct zscom *zs) 674 { 675 /* 676 * This routine is called near the end of the zs module's attach 677 * process. It initializes the TTY protocol-private data for this 678 * channel that needs to be in place before interrupts are enabled. 679 */ 680 mutex_enter(zs->zs_excl); 681 mutex_enter(zs->zs_excl_hi); 682 683 /* 684 * Raise modem control lines on serial ports associated 685 * with the console and (optionally) softcarrier lines. 686 * Drop modem control lines on all others so that modems 687 * will not answer and portselectors will skip these 688 * lines until they are opened by a getty. 689 */ 690 if (zsa_channel_is_active_in_rom(zs->zs_dip, zs->zs_unit)) 691 (void) zsmctl(zs, ZS_ON, DMSET); /* raise dtr */ 692 else if (zsasoftdtr && (zssoftCAR[zs->zs_unit])) 693 (void) zsmctl(zs, ZS_ON, DMSET); /* raise dtr */ 694 else 695 (void) zsmctl(zs, ZS_OFF, DMSET); /* drop dtr */ 696 697 if (zsa_rstandby > ZSA_MAX_RSTANDBY) 698 zsa_rstandby = ZSA_MAX_RSTANDBY; 699 700 if (zsa_rdone > ZSA_RDONE_MAX) 701 zsa_rdone = ZSA_RDONE_MAX; 702 703 if (zsa_grace_flow_control > ZSA_GRACE_MAX_FLOW_CONTROL) 704 zsa_grace_flow_control = ZSA_GRACE_MAX_FLOW_CONTROL; 705 706 mutex_exit(zs->zs_excl_hi); 707 mutex_exit(zs->zs_excl); 708 } 709 710 711 /* 712 * Open routine. 713 */ 714 /*ARGSUSED*/ 715 static int 716 zsa_open(queue_t *rq, dev_t *dev, int flag, int sflag, cred_t *cr) 717 { 718 register struct zscom *zs; 719 register struct asyncline *za; 720 register int speed, unit; 721 struct termios *termiosp; 722 int len; 723 register int allocbcount = zsa_rstandby; 724 boolean_t set_zsoptinit = B_FALSE; 725 726 unit = UNIT(*dev); 727 if (unit >= nzs) 728 return (ENXIO); /* unit not configured */ 729 730 /* zscom is allocated by zsattach, and thus cannot be NULL here */ 731 zs = &zscom[unit]; 732 if (zs->zs_ops == NULL) { 733 return (ENXIO); /* device not found by autoconfig */ 734 } 735 736 mutex_enter(zs->zs_ocexcl); 737 mutex_enter(zs->zs_excl); 738 again: 739 if ((zs->zs_ops != &zsops_null) && 740 (zs->zs_ops != &zsops_async)) { 741 mutex_exit(zs->zs_excl); 742 mutex_exit(zs->zs_ocexcl); 743 return (EBUSY); /* another protocol got here first */ 744 } 745 746 za = (struct asyncline *)&zs->zs_priv_str; 747 748 if (zs->zs_suspended) { 749 mutex_exit(zs->zs_excl); 750 mutex_exit(zs->zs_ocexcl); 751 (void) ddi_dev_is_needed(zs->zs_dip, 0, 1); 752 mutex_enter(zs->zs_ocexcl); 753 mutex_enter(zs->zs_excl); 754 } 755 756 /* Mark device as busy (for power management) */ 757 (void) pm_busy_component(zs->zs_dip, unit%2+1); 758 759 if (zs->zs_ops == &zsops_null) { 760 bzero(za, sizeof (zs->zs_priv_str)); 761 za->za_common = zs; 762 if (zssoftCAR[zs->zs_unit]) 763 za->za_ttycommon.t_flags |= TS_SOFTCAR; 764 zsopinit(zs, &zsops_async); 765 set_zsoptinit = B_TRUE; 766 za->za_rdone_wptr = 0; 767 za->za_rdone_rptr = 0; 768 } 769 770 zs->zs_priv = (caddr_t)za; 771 772 /* 773 * Block waiting for carrier to come up, 774 * unless this is a no-delay open. 775 */ 776 mutex_enter(zs->zs_excl_hi); 777 if (!(za->za_flags & ZAS_ISOPEN)) { 778 /* 779 * Get the default termios settings (cflag). 780 * These are stored as a property in the 781 * "options" node. 782 */ 783 mutex_exit(zs->zs_excl_hi); 784 if (ddi_getlongprop(DDI_DEV_T_ANY, 785 ddi_root_node(), 0, "ttymodes", 786 (caddr_t)&termiosp, &len) == DDI_PROP_SUCCESS && 787 len == sizeof (struct termios)) { 788 789 za->za_ttycommon.t_cflag = termiosp->c_cflag; 790 kmem_free(termiosp, len); 791 } else { 792 /* 793 * Gack! Whine about it. 794 */ 795 cmn_err(CE_WARN, 796 "zs: Couldn't get ttymodes property!"); 797 } 798 mutex_enter(zs->zs_excl_hi); 799 if ((*dev == rconsdev) || (*dev == kbddev) || 800 (*dev == stdindev)) { 801 speed = zsgetspeed(*dev); 802 za->za_ttycommon.t_cflag &= ~(CBAUD); 803 if (speed > CBAUD) { 804 za->za_ttycommon.t_cflag |= CBAUDEXT; 805 za->za_ttycommon.t_cflag |= 806 ((speed - CBAUD - 1) & CBAUD); 807 } else { 808 za->za_ttycommon.t_cflag &= ~CBAUDEXT; 809 za->za_ttycommon.t_cflag |= (speed & CBAUD); 810 } 811 } 812 za->za_overrun = 0; 813 za->za_ttycommon.t_iflag = 0; 814 za->za_ttycommon.t_iocpending = NULL; 815 za->za_ttycommon.t_size.ws_row = 0; 816 za->za_ttycommon.t_size.ws_col = 0; 817 za->za_ttycommon.t_size.ws_xpixel = 0; 818 za->za_ttycommon.t_size.ws_ypixel = 0; 819 za->za_dev = *dev; 820 za->za_wbufcid = 0; 821 zsa_program(za, za->za_ttycommon.t_cflag & (CIBAUDEXT|CIBAUD)); 822 zsa_set_za_rcv_flags_mask(za); 823 } else if ((za->za_ttycommon.t_flags & TS_XCLUDE) && 824 secpolicy_excl_open(cr) != 0) { 825 mutex_exit(zs->zs_excl_hi); 826 if (set_zsoptinit && !(za->za_flags & ISOPEN)) 827 zsopinit(zs, &zsops_null); 828 mutex_exit(zs->zs_excl); 829 mutex_exit(zs->zs_ocexcl); 830 return (EBUSY); 831 } else if ((*dev & OUTLINE) && !(za->za_flags & ZAS_OUT)) { 832 mutex_exit(zs->zs_excl_hi); 833 if (set_zsoptinit && !(za->za_flags & ISOPEN)) 834 zsopinit(zs, &zsops_null); 835 mutex_exit(zs->zs_excl); 836 mutex_exit(zs->zs_ocexcl); 837 return (EBUSY); 838 } 839 840 if (*dev & OUTLINE) 841 za->za_flags |= ZAS_OUT; 842 (void) zsmctl(zs, ZS_ON, DMSET); 843 844 /* 845 * Check carrier. 846 */ 847 if ((za->za_ttycommon.t_flags & TS_SOFTCAR) || 848 (zsmctl(zs, 0, DMGET) & ZSRR0_CD)) 849 za->za_flags |= ZAS_CARR_ON; 850 mutex_exit(zs->zs_excl_hi); 851 852 /* 853 * If FNDELAY and FNONBLOCK are clear, block until carrier up. 854 * Quit on interrupt. 855 */ 856 if (!(flag & (FNDELAY|FNONBLOCK)) && 857 !(za->za_ttycommon.t_cflag & CLOCAL)) { 858 if (!(za->za_flags & (ZAS_CARR_ON|ZAS_OUT)) || 859 ((za->za_flags & ZAS_OUT) && !(*dev & OUTLINE))) { 860 za->za_flags |= ZAS_WOPEN; 861 mutex_exit(zs->zs_excl); 862 if (cv_wait_sig(&zs->zs_flags_cv, zs->zs_ocexcl) == 0) { 863 mutex_enter(zs->zs_excl); 864 if (zs->zs_suspended) { 865 mutex_exit(zs->zs_excl); 866 mutex_exit(zs->zs_ocexcl); 867 (void) ddi_dev_is_needed(zs->zs_dip, 868 0, 1); 869 mutex_enter(zs->zs_ocexcl); 870 mutex_enter(zs->zs_excl); 871 } 872 za->za_flags &= ~ZAS_WOPEN; 873 if (set_zsoptinit && !(za->za_flags & ISOPEN)) 874 zsopinit(zs, &zsops_null); 875 mutex_exit(zs->zs_excl); 876 mutex_exit(zs->zs_ocexcl); 877 return (EINTR); 878 } 879 mutex_enter(zs->zs_excl); 880 za->za_flags &= ~ZAS_WOPEN; 881 if ((zs->zs_ops == &zsops_null) || 882 (zs->zs_ops == &zsops_async)) 883 goto again; 884 else { 885 if (set_zsoptinit && !(za->za_flags & ISOPEN)) 886 zsopinit(zs, &zsops_null); 887 mutex_exit(zs->zs_excl); 888 mutex_exit(zs->zs_ocexcl); 889 return (EBUSY); 890 } 891 } 892 } else if ((za->za_flags & ZAS_OUT) && !(*dev & OUTLINE)) { 893 if (set_zsoptinit && !(za->za_flags & ISOPEN)) 894 zsopinit(zs, &zsops_null); 895 mutex_exit(zs->zs_excl); 896 mutex_exit(zs->zs_ocexcl); 897 return (EBUSY); 898 } 899 900 za->za_ttycommon.t_readq = rq; 901 za->za_ttycommon.t_writeq = WR(rq); 902 rq->q_ptr = WR(rq)->q_ptr = (caddr_t)za; 903 904 za->za_flags |= ZAS_ISOPEN; 905 ZSA_GETBLOCK(zs, allocbcount); 906 qprocson(rq); 907 mutex_exit(zs->zs_excl); 908 mutex_exit(zs->zs_ocexcl); 909 return (0); 910 } 911 912 static void 913 zs_progress_check(void *arg) 914 { 915 struct asyncline *za = arg; 916 struct zscom *zs = za->za_common; 917 mblk_t *bp; 918 919 /* 920 * We define "progress" as either waiting on a timed break or delay, or 921 * having had at least one transmitter interrupt. If none of these are 922 * true, then just terminate the output and wake up that close thread. 923 */ 924 mutex_enter(zs->zs_excl); 925 if (!(zs->zs_flags & ZS_PROGRESS) && 926 !(za->za_flags & (ZAS_BREAK|ZAS_DELAY))) { 927 za->za_flags &= ~ZAS_BUSY; 928 mutex_enter(zs->zs_excl_hi); 929 za->za_rcv_flags_mask &= ~DO_RETRANSMIT; 930 zs->zs_wr_cur = NULL; 931 zs->zs_wr_lim = NULL; 932 bp = za->za_xmitblk; 933 za->za_xmitblk = NULL; 934 mutex_exit(zs->zs_excl_hi); 935 zs->zs_timer = 0; 936 mutex_exit(zs->zs_excl); 937 if (bp != NULL) 938 freeb(bp); 939 /* 940 * Since this timer is running, we know that we're in exit(2). 941 * That means that the user can't possibly be waiting on any 942 * valid ioctl(2) completion anymore, and we should just flush 943 * everything. 944 */ 945 flushq(za->za_ttycommon.t_writeq, FLUSHALL); 946 cv_broadcast(&zs->zs_flags_cv); 947 } else { 948 zs->zs_flags &= ~ZS_PROGRESS; 949 zs->zs_timer = timeout(zs_progress_check, za, 950 drv_usectohz(zs_drain_check)); 951 mutex_exit(zs->zs_excl); 952 } 953 } 954 955 /* 956 * Close routine. 957 * 958 * Important locking note: the zs_ocexcl lock is not held at all in this 959 * routine. This is intentional. That lock is used to coordinate multiple 960 * simultaneous opens on a stream, and there's no such thing as multiple 961 * simultaneous closes on a stream. 962 */ 963 964 /*ARGSUSED*/ 965 static int 966 zsa_close(queue_t *q, int flag) 967 { 968 struct asyncline *za; 969 struct zscom *zs; 970 int i; 971 mblk_t *bp; 972 timeout_id_t za_zsa_restart_id, za_kick_rcv_id; 973 bufcall_id_t za_bufcid, za_wbufcid; 974 int tmp; 975 976 za = q->q_ptr; 977 ASSERT(za != NULL); 978 979 zs = za->za_common; 980 981 mutex_enter(zs->zs_excl); 982 zs->zs_flags |= ZS_CLOSING; 983 984 /* 985 * There are two flavors of break -- timed (M_BREAK or TCSBRK) and 986 * untimed (TIOCSBRK). For the timed case, these are enqueued on our 987 * write queue and there's a timer running, so we don't have to worry 988 * about them. For the untimed case, though, the user obviously made a 989 * mistake, because these are handled immediately. We'll terminate the 990 * break now and honor their implicit request by discarding the rest of 991 * the data. 992 */ 993 if (!(za->za_flags & ZAS_BREAK) && (zs->zs_wreg[5] & ZSWR5_BREAK)) 994 goto nodrain; 995 996 /* 997 * If the user told us not to delay the close ("non-blocking"), then 998 * don't bother trying to drain. 999 * 1000 * If the user did M_STOP (ASYNC_STOPPED), there's no hope of ever 1001 * getting an M_START (since these messages aren't enqueued), and the 1002 * only other way to clear the stop condition is by loss of DCD, which 1003 * would discard the queue data. Thus, we drop the output data if 1004 * ASYNC_STOPPED is set. 1005 */ 1006 if ((flag & (FNDELAY|FNONBLOCK)) || (za->za_flags & ZAS_STOPPED)) 1007 goto nodrain; 1008 1009 /* 1010 * If there's any pending output, then we have to try to drain it. 1011 * There are two main cases to be handled: 1012 * - called by close(2): need to drain until done or until 1013 * a signal is received. No timeout. 1014 * - called by exit(2): need to drain while making progress 1015 * or until a timeout occurs. No signals. 1016 * 1017 * If we can't rely on receiving a signal to get us out of a hung 1018 * session, then we have to use a timer. In this case, we set a timer 1019 * to check for progress in sending the output data -- all that we ask 1020 * (at each interval) is that there's been some progress made. Since 1021 * the interrupt routine grabs buffers from the write queue, we can't 1022 * trust changes in zs_wr_cur. Instead, we use a progress flag. 1023 * 1024 * Note that loss of carrier will cause the output queue to be flushed, 1025 * and we'll wake up again and finish normally. 1026 */ 1027 if (!ddi_can_receive_sig() && zs_drain_check != 0) { 1028 zs->zs_flags &= ~ZS_PROGRESS; 1029 zs->zs_timer = timeout(zs_progress_check, za, 1030 drv_usectohz(zs_drain_check)); 1031 } 1032 1033 while (zs->zs_wr_cur != NULL || 1034 za->za_ttycommon.t_writeq->q_first != NULL || 1035 (za->za_flags & (ZAS_BUSY|ZAS_DELAY|ZAS_BREAK))) { 1036 if (cv_wait_sig(&zs->zs_flags_cv, zs->zs_excl) == 0) 1037 break; 1038 } 1039 1040 if (zs->zs_timer != 0) { 1041 (void) untimeout(zs->zs_timer); 1042 zs->zs_timer = 0; 1043 } 1044 1045 nodrain: 1046 /* 1047 * If break is in progress, stop it. 1048 */ 1049 mutex_enter(zs->zs_excl_hi); 1050 if (zs->zs_wreg[5] & ZSWR5_BREAK) { 1051 SCC_BIC(5, ZSWR5_BREAK); 1052 za->za_flags &= ~ZAS_BREAK; 1053 } 1054 1055 za_wbufcid = za->za_wbufcid; 1056 za_bufcid = za->za_bufcid; 1057 za_zsa_restart_id = za->za_zsa_restart_id; 1058 za_kick_rcv_id = za->za_kick_rcv_id; 1059 1060 za->za_wbufcid = za->za_bufcid = 0; 1061 za->za_zsa_restart_id = za->za_kick_rcv_id = 0; 1062 1063 /* 1064 * If line has HUPCL set or is incompletely opened, 1065 * and it is not the console or the keyboard, 1066 * fix up the modem lines. 1067 */ 1068 1069 zsopinit(zs, &zsops_null_async); 1070 1071 /* 1072 * Nobody, zsh or zs can now open this port until 1073 * zsopinit(zs, &zsops_null); 1074 * 1075 */ 1076 1077 if ((za->za_dev != rconsdev) && (za->za_dev != kbddev) && 1078 (za->za_dev != stdindev) && 1079 (((za->za_flags & (ZAS_WOPEN|ZAS_ISOPEN)) != ZAS_ISOPEN) || 1080 (za->za_ttycommon.t_cflag & HUPCL))) { 1081 /* 1082 * If DTR is being held high by softcarrier, 1083 * set up the ZS_ON set; if not, hang up. 1084 */ 1085 if (zsasoftdtr && (za->za_ttycommon.t_flags & TS_SOFTCAR)) 1086 (void) zsmctl(zs, ZS_ON, DMSET); 1087 else 1088 (void) zsmctl(zs, ZS_OFF, DMSET); 1089 mutex_exit(zs->zs_excl_hi); 1090 /* 1091 * Don't let an interrupt in the middle of close 1092 * bounce us back to the top; just continue 1093 * closing as if nothing had happened. 1094 */ 1095 tmp = cv_reltimedwait_sig(&zs->zs_flags_cv, zs->zs_excl, 1096 drv_usectohz(10000), TR_CLOCK_TICK); 1097 if (zs->zs_suspended) { 1098 mutex_exit(zs->zs_excl); 1099 (void) ddi_dev_is_needed(zs->zs_dip, 0, 1); 1100 mutex_enter(zs->zs_excl); 1101 } 1102 if (tmp == 0) 1103 goto out; 1104 mutex_enter(zs->zs_excl_hi); 1105 } 1106 1107 /* 1108 * If nobody's now using it, turn off receiver interrupts. 1109 */ 1110 if ((za->za_flags & (ZAS_ISOPEN|ZAS_WOPEN)) == 0) 1111 SCC_BIC(1, ZSWR1_RIE); 1112 mutex_exit(zs->zs_excl_hi); 1113 1114 out: 1115 /* 1116 * Clear out device state. 1117 */ 1118 ttycommon_close(&za->za_ttycommon); 1119 1120 za->za_ttycommon.t_readq = NULL; 1121 za->za_ttycommon.t_writeq = NULL; 1122 1123 mutex_enter(zs->zs_excl_hi); 1124 za->za_rcv_flags_mask &= ~DO_RETRANSMIT; 1125 zs->zs_wr_cur = NULL; 1126 zs->zs_wr_lim = NULL; 1127 bp = za->za_xmitblk; 1128 za->za_xmitblk = NULL; 1129 mutex_exit(zs->zs_excl_hi); 1130 if (bp) 1131 freemsg(bp); 1132 1133 mutex_enter(zs->zs_excl_hi); 1134 zs->zs_rd_cur = NULL; 1135 zs->zs_rd_lim = NULL; 1136 bp = za->za_rcvblk; 1137 za->za_rcvblk = NULL; 1138 mutex_exit(zs->zs_excl_hi); 1139 if (bp) 1140 freemsg(bp); 1141 1142 for (i = 0; i < zsa_rstandby; i++) { 1143 mutex_enter(zs->zs_excl_hi); 1144 bp = za->za_rstandby[i]; 1145 za->za_rstandby[i] = NULL; 1146 mutex_exit(zs->zs_excl_hi); 1147 if (bp) 1148 freemsg(bp); 1149 } 1150 1151 if (za->za_soft_active || za->za_kick_active) { 1152 zs->zs_flags |= ZS_CLOSED; 1153 while (za->za_soft_active || za->za_kick_active) 1154 cv_wait(&zs->zs_flags_cv, zs->zs_excl); 1155 } 1156 if (zs->zs_suspended) { 1157 mutex_exit(zs->zs_excl); 1158 (void) ddi_dev_is_needed(zs->zs_dip, 0, 1); 1159 mutex_enter(zs->zs_excl); 1160 } 1161 1162 ZSA_FLUSHQ; 1163 bzero(za, sizeof (struct asyncline)); 1164 qprocsoff(q); 1165 mutex_exit(zs->zs_excl); 1166 1167 /* 1168 * Cancel outstanding "bufcall" request. 1169 */ 1170 if (za_wbufcid) 1171 unbufcall(za_wbufcid); 1172 if (za_bufcid) 1173 unbufcall(za_bufcid); 1174 1175 /* 1176 * Cancel outstanding timeout. 1177 */ 1178 if (za_zsa_restart_id) 1179 (void) untimeout(za_zsa_restart_id); 1180 1181 if (za_kick_rcv_id) 1182 (void) untimeout(za_kick_rcv_id); 1183 1184 q->q_ptr = WR(q)->q_ptr = NULL; 1185 zsopinit(zs, &zsops_null); 1186 cv_broadcast(&zs->zs_flags_cv); 1187 1188 /* Mark device as available for power management */ 1189 (void) pm_idle_component(zs->zs_dip, zs->zs_unit%2+1); 1190 return (0); 1191 } 1192 1193 /* 1194 * Put procedure for write queue. 1195 * Respond to M_STOP, M_START, M_IOCTL, and M_FLUSH messages here; 1196 * set the flow control character for M_STOPI and M_STARTI messages; 1197 * queue up M_BREAK, M_DELAY, and M_DATA messages for processing 1198 * by the start routine, and then call the start routine; discard 1199 * everything else. Note that this driver does not incorporate any 1200 * mechanism to negotiate to handle the canonicalization process. 1201 * It expects that these functions are handled in upper module(s), 1202 * as we do in ldterm. 1203 */ 1204 static void 1205 zsa_wput(queue_t *q, mblk_t *mp) 1206 { 1207 register struct asyncline *za; 1208 register struct zscom *zs; 1209 register struct copyresp *resp; 1210 register mblk_t *bp = NULL; 1211 int error; 1212 struct iocblk *iocp; 1213 1214 za = (struct asyncline *)q->q_ptr; 1215 zs = za->za_common; 1216 if (zs->zs_flags & ZS_NEEDSOFT) { 1217 zs->zs_flags &= ~ZS_NEEDSOFT; 1218 (void) zsa_softint(zs); 1219 } 1220 1221 switch (mp->b_datap->db_type) { 1222 1223 case M_STOP: 1224 /* 1225 * Since we don't do real DMA, we can just let the 1226 * chip coast to a stop after applying the brakes. 1227 */ 1228 mutex_enter(zs->zs_excl); 1229 mutex_enter(zs->zs_excl_hi); 1230 za->za_flags |= ZAS_STOPPED; 1231 if ((zs->zs_wr_cur) != NULL) { 1232 za->za_flags &= ~ZAS_BUSY; 1233 za->za_rcv_flags_mask &= ~DO_RETRANSMIT; 1234 bp = za->za_xmitblk; 1235 bp->b_rptr = zs->zs_wr_cur; 1236 zs->zs_wr_cur = NULL; 1237 zs->zs_wr_lim = NULL; 1238 za->za_xmitblk = NULL; 1239 } 1240 mutex_exit(zs->zs_excl_hi); 1241 if (bp) 1242 (void) putbq(q, bp); 1243 freemsg(mp); 1244 mutex_exit(zs->zs_excl); 1245 break; 1246 1247 case M_START: 1248 mutex_enter(zs->zs_excl); 1249 if (za->za_flags & ZAS_STOPPED) { 1250 za->za_flags &= ~ZAS_STOPPED; 1251 /* 1252 * If an output operation is in progress, 1253 * resume it. Otherwise, prod the start 1254 * routine. 1255 */ 1256 zsa_start(zs); 1257 } 1258 freemsg(mp); 1259 mutex_exit(zs->zs_excl); 1260 break; 1261 1262 case M_IOCTL: 1263 mutex_enter(zs->zs_excl); 1264 iocp = (struct iocblk *)mp->b_rptr; 1265 1266 switch (iocp->ioc_cmd) { 1267 1268 case TIOCGPPS: 1269 /* 1270 * Get PPS state. 1271 */ 1272 if (mp->b_cont != NULL) 1273 freemsg(mp->b_cont); 1274 1275 mp->b_cont = allocb(sizeof (int), BPRI_HI); 1276 if (mp->b_cont == NULL) { 1277 mp->b_datap->db_type = M_IOCNAK; 1278 iocp->ioc_error = ENOMEM; 1279 ZSA_QREPLY(q, mp); 1280 break; 1281 } 1282 if (za->za_pps) 1283 *(int *)mp->b_cont->b_wptr = 1; 1284 else 1285 *(int *)mp->b_cont->b_wptr = 0; 1286 mp->b_cont->b_wptr += sizeof (int); 1287 mp->b_datap->db_type = M_IOCACK; 1288 iocp->ioc_count = sizeof (int); 1289 ZSA_QREPLY(q, mp); 1290 break; 1291 1292 case TIOCSPPS: 1293 /* 1294 * Set PPS state. 1295 */ 1296 error = miocpullup(mp, sizeof (int)); 1297 if (error != 0) { 1298 mp->b_datap->db_type = M_IOCNAK; 1299 iocp->ioc_error = error; 1300 ZSA_QREPLY(q, mp); 1301 break; 1302 } 1303 1304 za->za_pps = (*(int *)mp->b_cont->b_rptr != 0); 1305 mp->b_datap->db_type = M_IOCACK; 1306 ZSA_QREPLY(q, mp); 1307 break; 1308 1309 case TIOCGPPSEV: 1310 { 1311 /* 1312 * Get PPS event data. 1313 */ 1314 void *buf; 1315 #ifdef _SYSCALL32_IMPL 1316 struct ppsclockev32 p32; 1317 #endif 1318 1319 if (mp->b_cont != NULL) { 1320 freemsg(mp->b_cont); 1321 mp->b_cont = NULL; 1322 } 1323 if (za->za_pps == NULL) { 1324 mp->b_datap->db_type = M_IOCNAK; 1325 iocp->ioc_error = ENXIO; 1326 ZSA_QREPLY(q, mp); 1327 break; 1328 } 1329 1330 #ifdef _SYSCALL32_IMPL 1331 if ((iocp->ioc_flag & IOC_MODELS) != IOC_NATIVE) { 1332 TIMEVAL_TO_TIMEVAL32(&p32.tv, &ppsclockev.tv); 1333 p32.serial = ppsclockev.serial; 1334 buf = &p32; 1335 iocp->ioc_count = sizeof (struct ppsclockev32); 1336 } else 1337 #endif 1338 { 1339 buf = &ppsclockev; 1340 iocp->ioc_count = sizeof (struct ppsclockev); 1341 } 1342 1343 if ((bp = allocb(iocp->ioc_count, BPRI_HI)) == NULL) { 1344 mp->b_datap->db_type = M_IOCNAK; 1345 iocp->ioc_error = ENOMEM; 1346 ZSA_QREPLY(q, mp); 1347 break; 1348 } 1349 mp->b_cont = bp; 1350 1351 bcopy(buf, bp->b_wptr, iocp->ioc_count); 1352 bp->b_wptr += iocp->ioc_count; 1353 mp->b_datap->db_type = M_IOCACK; 1354 ZSA_QREPLY(q, mp); 1355 break; 1356 } 1357 1358 case TCSETSW: 1359 case TCSETSF: 1360 case TCSETAW: 1361 case TCSETAF: 1362 case TCSBRK: 1363 /* 1364 * The changes do not take effect until all 1365 * output queued before them is drained. 1366 * Put this message on the queue, so that 1367 * "zsa_start" will see it when it's done 1368 * with the output before it. Poke the 1369 * start routine, just in case. 1370 */ 1371 (void) putq(q, mp); 1372 zsa_start(zs); 1373 break; 1374 1375 default: 1376 /* 1377 * Do it now. 1378 */ 1379 zsa_ioctl(za, q, mp); 1380 break; 1381 } 1382 mutex_exit(zs->zs_excl); 1383 break; 1384 1385 1386 case M_IOCDATA: 1387 1388 mutex_enter(zs->zs_excl); 1389 resp = (struct copyresp *)mp->b_rptr; 1390 if (resp->cp_rval) { 1391 /* 1392 * Just free message on failure. 1393 */ 1394 freemsg(mp); 1395 mutex_exit(zs->zs_excl); 1396 break; 1397 } 1398 switch (resp->cp_cmd) { 1399 1400 case TIOCMSET: 1401 mutex_enter(zs->zs_excl_hi); 1402 (void) zsmctl(zs, dmtozs(*(int *)mp->b_cont->b_rptr), 1403 DMSET); 1404 mutex_exit(zs->zs_excl_hi); 1405 mioc2ack(mp, NULL, 0, 0); 1406 ZSA_QREPLY(q, mp); 1407 break; 1408 1409 case TIOCMBIS: 1410 mutex_enter(zs->zs_excl_hi); 1411 (void) zsmctl(zs, dmtozs(*(int *)mp->b_cont->b_rptr), 1412 DMBIS); 1413 mutex_exit(zs->zs_excl_hi); 1414 mioc2ack(mp, NULL, 0, 0); 1415 ZSA_QREPLY(q, mp); 1416 break; 1417 1418 case TIOCMBIC: 1419 mutex_enter(zs->zs_excl_hi); 1420 (void) zsmctl(zs, dmtozs(*(int *)mp->b_cont->b_rptr), 1421 DMBIC); 1422 mutex_exit(zs->zs_excl_hi); 1423 mioc2ack(mp, NULL, 0, 0); 1424 ZSA_QREPLY(q, mp); 1425 break; 1426 1427 case TIOCMGET: 1428 mioc2ack(mp, NULL, 0, 0); 1429 ZSA_QREPLY(q, mp); 1430 break; 1431 1432 default: 1433 freemsg(mp); 1434 1435 } 1436 mutex_exit(zs->zs_excl); 1437 break; 1438 1439 1440 case M_FLUSH: 1441 mutex_enter(zs->zs_excl); 1442 if (*mp->b_rptr & FLUSHW) { 1443 1444 /* 1445 * Abort any output in progress. 1446 */ 1447 if (za->za_flags & ZAS_BUSY) { 1448 za->za_flags &= ~ZAS_BUSY; 1449 mutex_enter(zs->zs_excl_hi); 1450 za->za_rcv_flags_mask &= ~DO_RETRANSMIT; 1451 zs->zs_wr_cur = NULL; 1452 zs->zs_wr_lim = NULL; 1453 bp = za->za_xmitblk; 1454 za->za_xmitblk = NULL; 1455 mutex_exit(zs->zs_excl_hi); 1456 if (bp) 1457 freemsg(bp); 1458 } 1459 /* 1460 * Flush our write queue. 1461 */ 1462 flushq(q, FLUSHDATA); /* XXX doesn't flush M_DELAY */ 1463 *mp->b_rptr &= ~FLUSHW; /* it has been flushed */ 1464 } 1465 if (*mp->b_rptr & FLUSHR) { 1466 /* 1467 * Flush any data in the temporary receive buffer 1468 */ 1469 mutex_enter(zs->zs_excl_hi); 1470 if ((za->za_ttycommon.t_flags & TS_SOFTCAR) || 1471 (SCC_READ0() & ZSRR0_CD)) { 1472 ZSA_KICK_RCV; 1473 } else { 1474 ZSA_KICK_RCV; 1475 if (!(SCC_READ0() & ZSRR0_RX_READY)) { 1476 /* 1477 * settle time for 1 character shift 1478 */ 1479 mutex_exit(zs->zs_excl_hi); 1480 mutex_exit(zs->zs_excl); 1481 delay(ztdelay(SPEED( 1482 za->za_ttycommon.t_cflag))/3 + 1); 1483 mutex_enter(zs->zs_excl); 1484 mutex_enter(zs->zs_excl_hi); 1485 if (!(SCC_READ0() & ZSRR0_CD)) 1486 ZSA_KICK_RCV; 1487 } 1488 while ((SCC_READ0() & 1489 (ZSRR0_CD | ZSRR0_RX_READY)) == 1490 ZSRR0_RX_READY) { 1491 /* 1492 * Empty Receiver 1493 */ 1494 (void) SCC_READDATA(); 1495 } 1496 } 1497 mutex_exit(zs->zs_excl_hi); 1498 flushq(RD(q), FLUSHDATA); 1499 ZSA_QREPLY(q, mp); 1500 /* 1501 * give the read queues a crack at it 1502 */ 1503 } else 1504 freemsg(mp); 1505 1506 /* 1507 * We must make sure we process messages that survive the 1508 * write-side flush. Without this call, the close protocol 1509 * with ldterm can hang forever. (ldterm will have sent us a 1510 * TCSBRK ioctl that it expects a response to.) 1511 */ 1512 zsa_start(zs); 1513 mutex_exit(zs->zs_excl); 1514 break; 1515 1516 case M_BREAK: 1517 case M_DELAY: 1518 case M_DATA: 1519 mutex_enter(zs->zs_excl); 1520 /* 1521 * Queue the message up to be transmitted, 1522 * and poke the start routine. 1523 */ 1524 (void) putq(q, mp); 1525 zsa_start(zs); 1526 mutex_exit(zs->zs_excl); 1527 break; 1528 1529 case M_STOPI: 1530 mutex_enter(zs->zs_excl); 1531 mutex_enter(zs->zs_excl_hi); 1532 za->za_flowc = za->za_ttycommon.t_stopc; 1533 if ((zs->zs_wr_cur) != NULL) { 1534 za->za_rcv_flags_mask &= ~DO_RETRANSMIT; 1535 bp = za->za_xmitblk; 1536 bp->b_rptr = zs->zs_wr_cur; 1537 zs->zs_wr_cur = NULL; 1538 zs->zs_wr_lim = NULL; 1539 za->za_xmitblk = NULL; 1540 } 1541 mutex_exit(zs->zs_excl_hi); 1542 if (bp) 1543 (void) putbq(q, bp); 1544 else 1545 zsa_start(zs); /* poke the start routine */ 1546 freemsg(mp); 1547 mutex_exit(zs->zs_excl); 1548 break; 1549 1550 case M_STARTI: 1551 mutex_enter(zs->zs_excl); 1552 mutex_enter(zs->zs_excl_hi); 1553 za->za_flowc = za->za_ttycommon.t_startc; 1554 if ((zs->zs_wr_cur) != NULL) { 1555 za->za_rcv_flags_mask &= ~DO_RETRANSMIT; 1556 bp = za->za_xmitblk; 1557 bp->b_rptr = zs->zs_wr_cur; 1558 zs->zs_wr_cur = NULL; 1559 zs->zs_wr_lim = NULL; 1560 za->za_xmitblk = NULL; 1561 } 1562 mutex_exit(zs->zs_excl_hi); 1563 if (bp) 1564 (void) putbq(q, bp); 1565 else 1566 zsa_start(zs); /* poke the start routine */ 1567 freemsg(mp); 1568 mutex_exit(zs->zs_excl); 1569 break; 1570 1571 case M_CTL: 1572 if (MBLKL(mp) >= sizeof (struct iocblk) && 1573 ((struct iocblk *)mp->b_rptr)->ioc_cmd == MC_POSIXQUERY) { 1574 ((struct iocblk *)mp->b_rptr)->ioc_cmd = MC_HAS_POSIX; 1575 qreply(q, mp); 1576 } else { 1577 /* 1578 * These MC_SERVICE type messages are used by upper 1579 * modules to tell this driver to send input up 1580 * immediately, or that it can wait for normal 1581 * processing that may or may not be done. Sun 1582 * requires these for the mouse module. 1583 */ 1584 mutex_enter(zs->zs_excl); 1585 switch (*mp->b_rptr) { 1586 1587 case MC_SERVICEIMM: 1588 mutex_enter(zs->zs_excl_hi); 1589 za->za_flags |= ZAS_SERVICEIMM; 1590 mutex_exit(zs->zs_excl_hi); 1591 break; 1592 1593 case MC_SERVICEDEF: 1594 mutex_enter(zs->zs_excl_hi); 1595 za->za_flags &= ~ZAS_SERVICEIMM; 1596 mutex_exit(zs->zs_excl_hi); 1597 break; 1598 } 1599 freemsg(mp); 1600 mutex_exit(zs->zs_excl); 1601 } 1602 break; 1603 1604 default: 1605 /* 1606 * "No, I don't want a subscription to Chain Store Age, 1607 * thank you anyway." 1608 */ 1609 freemsg(mp); 1610 break; 1611 } 1612 } 1613 1614 /* 1615 * zs read service procedure 1616 */ 1617 static void 1618 zsa_rsrv(queue_t *q) 1619 { 1620 struct asyncline *za; 1621 struct zscom *zs; 1622 1623 if (((za = (struct asyncline *)q->q_ptr) != NULL) && 1624 (za->za_ttycommon.t_cflag & CRTSXOFF)) { 1625 zs = za->za_common; 1626 mutex_enter(zs->zs_excl_hi); 1627 ZSSETSOFT(zs); 1628 mutex_exit(zs->zs_excl_hi); 1629 } 1630 } 1631 1632 /* 1633 * Transmitter interrupt service routine. 1634 * If there's more data to transmit in the current pseudo-DMA block, 1635 * and the transmitter is ready, send the next character if output 1636 * is not stopped or draining. 1637 * Otherwise, queue up a soft interrupt. 1638 */ 1639 static void 1640 zsa_txint(struct zscom *zs) 1641 { 1642 register struct asyncline *za = (struct asyncline *)&zs->zs_priv_str; 1643 register uchar_t *wr_cur; 1644 register uchar_t s0; 1645 1646 s0 = SCC_READ0(); 1647 1648 if ((wr_cur = zs->zs_wr_cur) != NULL) { 1649 if (wr_cur < zs->zs_wr_lim) { 1650 if ((za->za_ttycommon.t_cflag & CRTSCTS) && 1651 !(s0 & ZSRR0_CTS)) { 1652 SCC_WRITE0(ZSWR0_RESET_TXINT); 1653 za->za_rcv_flags_mask |= DO_RETRANSMIT; 1654 return; 1655 } 1656 SCC_WRITEDATA(*wr_cur++); 1657 #ifdef ZSA_DEBUG 1658 za->za_wr++; 1659 #endif 1660 zs->zs_wr_cur = wr_cur; 1661 zs->zs_flags |= ZS_PROGRESS; 1662 return; 1663 } else { 1664 zs->zs_wr_cur = NULL; 1665 zs->zs_wr_lim = NULL; 1666 /* 1667 * Use the rcv_flags_mask as it is set and 1668 * test while holding the zs_excl_hi mutex 1669 */ 1670 za->za_rcv_flags_mask |= DO_TRANSMIT; 1671 SCC_WRITE0(ZSWR0_RESET_TXINT); 1672 ZSSETSOFT(zs); 1673 return; 1674 } 1675 } 1676 1677 if (za->za_flowc != '\0' && (!(za->za_flags & ZAS_DRAINING))) { 1678 if ((za->za_ttycommon.t_cflag & CRTSCTS) && 1679 !(s0 & ZSRR0_CTS)) { 1680 SCC_WRITE0(ZSWR0_RESET_TXINT); 1681 return; 1682 } 1683 SCC_WRITEDATA(za->za_flowc); 1684 za->za_flowc = '\0'; 1685 return; 1686 } 1687 SCC_WRITE0(ZSWR0_RESET_TXINT); 1688 /* 1689 * Set DO_TRANSMIT bit so that the soft interrupt can 1690 * test it and unset the ZAS_BUSY in za_flags while holding 1691 * the mutex zs_excl and zs_excl_hi 1692 */ 1693 za->za_rcv_flags_mask |= DO_TRANSMIT; 1694 ZSSETSOFT(zs); 1695 } 1696 1697 /* 1698 * External/Status interrupt. 1699 */ 1700 static void 1701 zsa_xsint(struct zscom *zs) 1702 { 1703 register struct asyncline *za = (struct asyncline *)&zs->zs_priv_str; 1704 register uchar_t s0, x0; 1705 1706 s0 = SCC_READ0(); 1707 ZSA_R0_LOG(s0); 1708 x0 = s0 ^ za->za_rr0; 1709 za->za_rr0 = s0; 1710 SCC_WRITE0(ZSWR0_RESET_STATUS); 1711 1712 /* 1713 * PPS (Pulse Per Second) support. 1714 */ 1715 if (za->za_pps && (x0 & ZSRR0_CD) && (s0 & ZSRR0_CD)) { 1716 /* 1717 * This code captures a timestamp at the designated 1718 * transition of the PPS signal (CD asserted). The 1719 * code provides a pointer to the timestamp, as well 1720 * as the hardware counter value at the capture. 1721 * 1722 * Note: the kernel has nano based time values while 1723 * NTP requires micro based, an in-line fast algorithm 1724 * to convert nsec to usec is used here -- see hrt2ts() 1725 * in common/os/timers.c for a full description. 1726 */ 1727 struct timeval *tvp = &ppsclockev.tv; 1728 timespec_t ts; 1729 int nsec, usec; 1730 1731 LED_OFF; 1732 gethrestime(&ts); 1733 LED_ON; 1734 nsec = ts.tv_nsec; 1735 usec = nsec + (nsec >> 2); 1736 usec = nsec + (usec >> 1); 1737 usec = nsec + (usec >> 2); 1738 usec = nsec + (usec >> 4); 1739 usec = nsec - (usec >> 3); 1740 usec = nsec + (usec >> 2); 1741 usec = nsec + (usec >> 3); 1742 usec = nsec + (usec >> 4); 1743 usec = nsec + (usec >> 1); 1744 usec = nsec + (usec >> 6); 1745 tvp->tv_usec = usec >> 10; 1746 tvp->tv_sec = ts.tv_sec; 1747 1748 ++ppsclockev.serial; 1749 1750 /* 1751 * Because the kernel keeps a high-resolution time, pass the 1752 * current highres timestamp in tvp and zero in usec. 1753 */ 1754 ddi_hardpps(tvp, 0); 1755 } 1756 1757 ZSA_KICK_RCV; 1758 1759 if ((x0 & ZSRR0_BREAK) && (s0 & ZSRR0_BREAK) == 0) { 1760 #ifdef SLAVIO_BUG 1761 /* 1762 * ZSRR0_BREAK turned off. This means that the break sequence 1763 * has completed (i.e., the stop bit finally arrived). 1764 */ 1765 if ((s0 & ZSRR0_RX_READY) == 0) { 1766 /* 1767 * SLAVIO will generate a separate STATUS change 1768 * interrupt when the break sequence completes. 1769 * SCC will combine both, taking the higher priority 1770 * one, the receive. Should still see the ext/stat. 1771 * bit in REG3 on SCC. If no ext/stat, it must be 1772 * a SLAVIO. 1773 */ 1774 za->za_breakoff = 1; 1775 } else { 1776 /* 1777 * The NUL character in the receiver is part of the 1778 * break sequence; it is discarded. 1779 */ 1780 (void) SCC_READDATA(); /* swallow null */ 1781 } 1782 #else /* SLAVIO_BUG */ 1783 /* 1784 * ZSRR0_BREAK turned off. This means that the break sequence 1785 * has completed (i.e., the stop bit finally arrived). The NUL 1786 * character in the receiver is part of the break sequence; 1787 * it is discarded. 1788 */ 1789 (void) SCC_READDATA(); /* swallow null */ 1790 #endif /* SLAVIO_BUG */ 1791 SCC_WRITE0(ZSWR0_RESET_ERRORS); 1792 1793 /* 1794 * Note: this will cause an abort if a break occurs on 1795 * the "keyboard device", regardless of whether the 1796 * "keyboard device" is a real keyboard or just a 1797 * terminal on a serial line. This permits you to 1798 * abort a workstation by unplugging the keyboard, 1799 * even if the normal abort key sequence isn't working. 1800 */ 1801 if ((za->za_dev == kbddev) || 1802 ((za->za_dev == rconsdev) || (za->za_dev == stdindev)) && 1803 (abort_enable != KIOCABORTALTERNATE)) { 1804 abort_sequence_enter((char *)NULL); 1805 /* 1806 * We just broke into the monitor or debugger, 1807 * ignore the break in this case so whatever 1808 * random program that was running doesn't get 1809 * a SIGINT. 1810 */ 1811 return; 1812 } 1813 za->za_break = 1; 1814 } 1815 1816 /* 1817 * If hardware flow control is enabled, (re)start output 1818 * when CTS is reasserted. 1819 */ 1820 if ((za->za_ttycommon.t_cflag & CRTSCTS) && 1821 (x0 & ZSRR0_CTS) && (s0 & ZSRR0_CTS) && 1822 (za->za_rcv_flags_mask & DO_RETRANSMIT)) 1823 za->za_rcv_flags_mask |= DO_TRANSMIT; 1824 1825 za->za_ext = 1; 1826 ZSSETSOFT(zs); 1827 } 1828 1829 /* 1830 * Receive Interrupt 1831 */ 1832 static void 1833 zsa_rxint(struct zscom *zs) 1834 { 1835 register struct asyncline *za = (struct asyncline *)&zs->zs_priv_str; 1836 register uchar_t c; 1837 register uchar_t *rd_cur = zs->zs_rd_cur; 1838 register uchar_t *rd_lim = zs->zs_rd_lim; 1839 register mblk_t *bp; 1840 register uint_t fm = za->za_rcv_flags_mask; 1841 1842 1843 #ifdef ZSA_DEBUG 1844 za->za_rd++; 1845 #endif 1846 c = (fm >> 16) & (SCC_READDATA()); 1847 1848 /* 1849 * Check for character break sequence 1850 */ 1851 if ((abort_enable == KIOCABORTALTERNATE) && (za->za_dev == rconsdev)) { 1852 if (abort_charseq_recognize(c)) 1853 abort_sequence_enter((char *)NULL); 1854 } 1855 1856 if (!rd_cur) { 1857 #ifdef SLAVIO_BUG 1858 /* 1859 * SLAVIO generates FE for the start of break and 1860 * during break when parity is set. End of break is 1861 * detected when the first character is received. 1862 * This character is always garbage and is thrown away. 1863 */ 1864 if (za->za_slav_break) { 1865 za->za_slav_break = 0; 1866 za->za_rr0 |= ZSRR0_BREAK; 1867 zsa_xsint(zs); 1868 return; 1869 } 1870 #endif /* SLAVIO_BUG */ 1871 1872 if (c == 0 && (za->za_rr0 & ZSRR0_BREAK)) { 1873 /* 1874 * A break sequence was under way, and a NUL character 1875 * was received. Discard the NUL character, as it is 1876 * part of the break sequence; if ZSRR0_BREAK turned 1877 * off, indicating that the break sequence has com- 1878 * pleted, call "zsa_xsint" to properly handle the 1879 * error. It would appear that External/Status 1880 * interrupts get lost occasionally, so this ensures 1881 * that one is delivered. 1882 */ 1883 c = SCC_READ0(); 1884 if (!(c & ZSRR0_BREAK)) 1885 zsa_xsint(zs); 1886 return; 1887 } 1888 1889 #ifdef SLAVIO_BUG 1890 if (c == 0 && za->za_breakoff) { 1891 /* 1892 * A break sequence completed, but SLAVIO generates 1893 * the NULL character interrupt late, so we throw the 1894 * NULL away now. 1895 */ 1896 return; 1897 } 1898 1899 /* 1900 * make sure it gets cleared. 1901 */ 1902 za->za_breakoff = 0; 1903 #endif /* SLAVIO_BUG */ 1904 1905 ZSA_KICK_RCV; /* We can have M_BREAK msg */ 1906 ZSA_ALLOCB(bp); 1907 if (!bp) { 1908 za->za_sw_overrun++; 1909 ZSSETSOFT(zs); 1910 return; 1911 } 1912 za->za_rcvblk = bp; 1913 zs->zs_rd_cur = rd_cur = bp->b_wptr; 1914 zs->zs_rd_lim = rd_lim = bp->b_datap->db_lim; 1915 if (za->za_kick_rcv_id == 0) 1916 ZSSETSOFT(zs); 1917 } 1918 if (c == 0377 && (fm & DO_ESC)) { 1919 if (rd_lim < rd_cur + 2) { 1920 ZSA_ALLOCB(bp); 1921 ZSA_KICK_RCV; 1922 if (!bp) { 1923 za->za_sw_overrun++; 1924 return; 1925 } 1926 za->za_rcvblk = bp; 1927 zs->zs_rd_cur = rd_cur = bp->b_wptr; 1928 zs->zs_rd_lim = rd_lim = bp->b_datap->db_lim; 1929 } 1930 *rd_cur++ = c; 1931 } 1932 1933 1934 *rd_cur++ = c; 1935 zs->zs_rd_cur = rd_cur; 1936 1937 if (rd_cur == rd_lim) { 1938 ZSA_KICK_RCV; 1939 } else if ((fm & DO_STOPC) && (c == (fm & 0xff))) { 1940 za->za_do_kick_rcv_in_softint = 1; 1941 ZSSETSOFT(zs); 1942 } 1943 1944 if ((za->za_flags & ZAS_SERVICEIMM) || g_nocluster) { 1945 /* 1946 * Send the data up immediately 1947 */ 1948 ZSA_KICK_RCV; 1949 } 1950 } 1951 1952 /* 1953 * Special receive condition interrupt handler. 1954 */ 1955 static void 1956 zsa_srint(struct zscom *zs) 1957 { 1958 register struct asyncline *za = (struct asyncline *)&zs->zs_priv_str; 1959 register short s1; 1960 register uchar_t c; 1961 register uchar_t c1; 1962 register mblk_t *bp = za->za_rcvblk; 1963 register uchar_t *rd_cur = zs->zs_rd_cur; 1964 1965 SCC_READ(1, s1); 1966 if (s1 & (ZSRR1_FE | ZSRR1_PE | ZSRR1_DO)) { 1967 c = SCC_READDATA(); /* swallow bad character */ 1968 } 1969 #ifdef SLAVIO_BUG 1970 /* 1971 * SLAVIO does not handle breaks properly when parity is enabled. 1972 * 1973 * In general, if a null character is received when a framing 1974 * error occurs then it is a break condition and not a real 1975 * framing error. The null character must be limited to the 1976 * number of bits including the parity bit. For example, a 6 1977 * bit character with parity would be null if the lower 7 bits 1978 * read from the receive fifo were 0. (The higher order bits are 1979 * padded with 1 and/or the stop bits.) The only exception to this 1980 * general rule would be an 8 bit null character with parity being 1981 * a 1 in the parity bit and a framing error. This exception 1982 * can be determined by examining the parity error bit in RREG 1. 1983 * 1984 * A null character, even parity, 8 bits, no parity error, 1985 * (0 0000 0000) with framing error is a break condition. 1986 * 1987 * A null character, even parity, 8 bits, parity error, 1988 * (1 0000 0000) with framing error is a framing error. 1989 * 1990 * A null character, odd parity, 8 bits, parity error 1991 * (0 0000 0000) with framing error is a break condition. 1992 * 1993 * A null character, odd parity, 8 bits, no parity error, 1994 * (1 0000 0000) with framing error is a framing error. 1995 */ 1996 if (za->za_ttycommon.t_cflag & PARENB) { 1997 switch (za->za_ttycommon.t_cflag & CSIZE) { 1998 1999 case CS5: 2000 c1 = c & 0x3f; 2001 break; 2002 2003 case CS6: 2004 c1 = c & 0x7f; 2005 break; 2006 2007 case CS7: 2008 c1 = c & 0xff; 2009 break; 2010 2011 case CS8: 2012 if ((za->za_ttycommon.t_cflag & PARODD) && 2013 !(s1 & ZSRR1_PE)) 2014 c1 = 0xff; 2015 else if (!(za->za_ttycommon.t_cflag & PARODD) && 2016 (s1 & ZSRR1_PE)) 2017 c1 = 0xff; 2018 else 2019 c1 = c; 2020 break; 2021 } 2022 2023 /* 2024 * We fake start of break condition. 2025 */ 2026 if ((s1 & ZSRR1_FE) && c1 == 0) { 2027 za->za_slav_break = 1; 2028 return; 2029 } 2030 } 2031 #endif /* SLAVIO_BUG */ 2032 2033 if (s1 & ZSRR1_PE) { 2034 2035 /* 2036 * Mark the parity error so zsa_process will 2037 * notice it and send it up in an M_BREAK 2038 * message; ldterm will do the actual parity error 2039 * processing 2040 */ 2041 2042 if (bp && zs->zs_rd_cur) { /* M_DATA msg */ 2043 ZSA_KICK_RCV; 2044 bp = NULL; 2045 } 2046 if (!bp) 2047 ZSA_ALLOCB(bp); 2048 if (!bp) { 2049 za->za_sw_overrun++; 2050 ZSSETSOFT(zs); 2051 } else { 2052 za->za_rcvblk = bp; 2053 zs->zs_rd_cur = rd_cur = bp->b_wptr; 2054 zs->zs_rd_lim = bp->b_datap->db_lim; 2055 *rd_cur++ = c; 2056 zs->zs_rd_cur = rd_cur; 2057 bp->b_datap->db_type = M_BREAK; 2058 if (bp->b_datap->db_lim <= rd_cur) 2059 ZSA_KICK_RCV; 2060 za->za_do_kick_rcv_in_softint = 1; 2061 ZSSETSOFT(zs); 2062 2063 } 2064 } 2065 SCC_WRITE0(ZSWR0_RESET_ERRORS); 2066 if (s1 & ZSRR1_DO) { 2067 za->za_hw_overrun++; 2068 ZSSETSOFT(zs); 2069 } 2070 } 2071 2072 /* 2073 * Process software interrupts (or poll) 2074 * Crucial points: 2075 * 3. BUG - breaks are handled "out-of-band" - their relative position 2076 * among input events is lost, as well as multiple breaks together. 2077 * This is probably not a problem in practice. 2078 */ 2079 static int 2080 zsa_softint(struct zscom *zs) 2081 { 2082 register struct asyncline *za = (struct asyncline *)&zs->zs_priv_str; 2083 register uchar_t r0; 2084 register uchar_t za_kick_active; 2085 register int m_error; 2086 register int allocbcount = 0; 2087 register int do_ttycommon_qfull = 0; 2088 boolean_t hangup = B_FALSE, unhangup = B_FALSE; 2089 boolean_t m_break = B_FALSE, wakeup = B_FALSE; 2090 register queue_t *q; 2091 register mblk_t *bp; 2092 register mblk_t *head = NULL, *tail = NULL; 2093 2094 mutex_enter(zs->zs_excl); 2095 if (zs->zs_suspended || (zs->zs_flags & ZS_CLOSED)) { 2096 mutex_exit(zs->zs_excl); 2097 return (0); 2098 } 2099 q = za->za_ttycommon.t_readq; 2100 if (za->za_flags & ZAS_WOPEN && !q) { 2101 if (za->za_ext) { 2102 mutex_enter(zs->zs_excl_hi); 2103 r0 = SCC_READ0(); 2104 za->za_ext = 0; 2105 mutex_exit(zs->zs_excl_hi); 2106 /* 2107 * carrier up? 2108 */ 2109 if ((r0 & ZSRR0_CD) || 2110 (za->za_ttycommon.t_flags & TS_SOFTCAR)) { 2111 /* 2112 * carrier present 2113 */ 2114 if ((za->za_flags & ZAS_CARR_ON) == 0) { 2115 za->za_flags |= ZAS_CARR_ON; 2116 mutex_exit(zs->zs_excl); 2117 cv_broadcast(&zs->zs_flags_cv); 2118 return (0); 2119 } 2120 } 2121 } 2122 mutex_exit(zs->zs_excl); 2123 return (0); 2124 } 2125 q = za->za_ttycommon.t_readq; 2126 if (!q) { 2127 mutex_exit(zs->zs_excl); 2128 return (0); 2129 } 2130 2131 m_error = za->za_m_error; 2132 za->za_m_error = 0; 2133 2134 if (za->za_do_kick_rcv_in_softint) { 2135 mutex_enter(zs->zs_excl_hi); 2136 ZSA_KICK_RCV; 2137 za->za_do_kick_rcv_in_softint = 0; 2138 mutex_exit(zs->zs_excl_hi); 2139 } 2140 2141 za_kick_active = za->za_kick_active; 2142 2143 while (!za_kick_active) { 2144 ZSA_SEEQ(bp); 2145 if (!bp) 2146 break; 2147 2148 allocbcount++; 2149 2150 if (bp->b_datap->db_type <= QPCTL) { 2151 if (!(canputnext(q))) { 2152 if (za->za_grace_flow_control >= 2153 zsa_grace_flow_control) { 2154 if (za->za_ttycommon.t_cflag & 2155 CRTSXOFF) { 2156 allocbcount--; 2157 break; 2158 } 2159 ZSA_GETQ(bp); 2160 freemsg(bp); 2161 do_ttycommon_qfull = 1; 2162 continue; 2163 } else 2164 za->za_grace_flow_control++; 2165 } else 2166 za->za_grace_flow_control = 0; 2167 } 2168 ZSA_GETQ(bp); 2169 if (!head) { 2170 head = bp; 2171 } else { 2172 if (!tail) 2173 tail = head; 2174 tail->b_next = bp; 2175 tail = bp; 2176 } 2177 } 2178 2179 if (allocbcount) 2180 ZSA_GETBLOCK(zs, allocbcount); 2181 2182 if (za->za_ext) { 2183 mutex_enter(zs->zs_excl_hi); 2184 r0 = SCC_READ0(); 2185 za->za_ext = 0; 2186 /* 2187 * carrier up? 2188 */ 2189 if ((r0 & ZSRR0_CD) || 2190 (za->za_ttycommon.t_flags & TS_SOFTCAR)) { 2191 /* 2192 * carrier present 2193 */ 2194 if ((za->za_flags & ZAS_CARR_ON) == 0) { 2195 za->za_flags |= ZAS_CARR_ON; 2196 unhangup = B_TRUE; 2197 wakeup = B_TRUE; 2198 } 2199 } else { 2200 if ((za->za_flags & ZAS_CARR_ON) && 2201 !(za->za_ttycommon.t_cflag & CLOCAL)) { 2202 /* 2203 * Carrier went away. 2204 * Drop DTR, abort any output in progress, 2205 * indicate that output is not stopped, and 2206 * send a hangup notification upstream. 2207 */ 2208 (void) zsmctl(zs, ZSWR5_DTR, DMBIC); 2209 if ((za->za_flags & ZAS_BUSY) && 2210 (zs->zs_wr_cur != NULL)) { 2211 zs->zs_wr_cur = NULL; 2212 zs->zs_wr_lim = NULL; 2213 } 2214 hangup = B_TRUE; 2215 wakeup = B_TRUE; 2216 za->za_flags &= ~(ZAS_STOPPED | ZAS_CARR_ON | 2217 ZAS_BUSY); 2218 za->za_rcv_flags_mask &= ~(DO_TRANSMIT | 2219 DO_RETRANSMIT); 2220 } 2221 } 2222 mutex_exit(zs->zs_excl_hi); 2223 if (hangup && (bp = za->za_xmitblk) != NULL) { 2224 za->za_xmitblk = NULL; 2225 freeb(bp); 2226 } 2227 } 2228 2229 if (za->za_break != 0) { 2230 mutex_enter(zs->zs_excl_hi); 2231 r0 = SCC_READ0(); 2232 mutex_exit(zs->zs_excl_hi); 2233 if ((r0 & ZSRR0_BREAK) == 0) { 2234 za->za_break = 0; 2235 m_break = B_TRUE; 2236 } 2237 } 2238 2239 /* 2240 * If a transmission has finished, indicate that it's 2241 * finished, and start that line up again. 2242 */ 2243 2244 mutex_enter(zs->zs_excl_hi); 2245 if (za->za_rcv_flags_mask & DO_TRANSMIT) { 2246 za->za_rcv_flags_mask &= ~DO_TRANSMIT; 2247 za->za_flags &= ~ZAS_BUSY; 2248 2249 if ((za->za_ttycommon.t_cflag & CRTSCTS) && 2250 (za->za_rcv_flags_mask & DO_RETRANSMIT) && 2251 zs->zs_wr_cur) 2252 bp = NULL; 2253 else { 2254 za->za_rcv_flags_mask &= ~DO_RETRANSMIT; 2255 bp = za->za_xmitblk; 2256 za->za_xmitblk = 0; 2257 } 2258 mutex_exit(zs->zs_excl_hi); 2259 if (bp) 2260 freemsg(bp); 2261 zsa_start(zs); 2262 /* if we didn't start anything, then notify waiters */ 2263 if (!(za->za_flags & ZAS_BUSY)) 2264 wakeup = B_TRUE; 2265 } else { 2266 mutex_exit(zs->zs_excl_hi); 2267 } 2268 2269 2270 /* 2271 * A note about these overrun bits: all they do is *tell* someone 2272 * about an error- They do not track multiple errors. In fact, 2273 * you could consider them latched register bits if you like. 2274 * We are only interested in printing the error message once for 2275 * any cluster of overrun errors. 2276 */ 2277 if ((!za->za_kick_rcv_id) && (zs->zs_rd_cur || za_kick_active)) { 2278 if (g_zsticks) 2279 za->za_kick_rcv_id = timeout(zsa_kick_rcv, zs, 2280 g_zsticks); 2281 else 2282 za->za_kick_rcv_id = timeout(zsa_kick_rcv, zs, 2283 zsticks[SPEED(za->za_ttycommon.t_cflag)]); 2284 za->za_kick_rcv_count = ZA_KICK_RCV_COUNT; 2285 } 2286 za->za_soft_active = 1; 2287 mutex_exit(zs->zs_excl); 2288 2289 if (!hangup && do_ttycommon_qfull) { 2290 ttycommon_qfull(&za->za_ttycommon, q); 2291 mutex_enter(zs->zs_excl); 2292 zsa_start(zs); 2293 mutex_exit(zs->zs_excl); 2294 } 2295 2296 if (za->za_hw_overrun > 10) { 2297 cmn_err(CE_NOTE, "zs%d: silo overflow\n", UNIT(za->za_dev)); 2298 za->za_hw_overrun = 0; 2299 } 2300 2301 if (za->za_sw_overrun > 10) { 2302 cmn_err(CE_NOTE, "zs%d:ring buffer overflow\n", 2303 UNIT(za->za_dev)); 2304 za->za_sw_overrun = 0; 2305 } 2306 2307 if (unhangup) 2308 (void) putnextctl(q, M_UNHANGUP); 2309 2310 if (m_break) 2311 (void) putnextctl(q, M_BREAK); 2312 2313 while (head) { 2314 if (!tail) { 2315 putnext(q, head); 2316 break; 2317 } 2318 bp = head; 2319 head = head->b_next; 2320 bp->b_next = NULL; 2321 putnext(q, bp); 2322 } 2323 2324 if (hangup) { 2325 int flushflag; 2326 2327 /* 2328 * If we're in the midst of close, then flush everything. Don't 2329 * leave stale ioctls lying about. 2330 */ 2331 flushflag = (zs->zs_flags & ZS_CLOSING) ? FLUSHALL : FLUSHDATA; 2332 flushq(za->za_ttycommon.t_writeq, flushflag); 2333 (void) putnextctl(q, M_HANGUP); 2334 } 2335 2336 if (m_error) 2337 (void) putnextctl1(q, M_ERROR, m_error); 2338 2339 za->za_soft_active = 0; 2340 2341 if (wakeup || (zs->zs_flags & ZS_CLOSED)) 2342 cv_broadcast(&zs->zs_flags_cv); 2343 2344 return (0); 2345 } 2346 2347 /* 2348 * Start output on a line, unless it's busy, frozen, or otherwise. 2349 */ 2350 static void 2351 zsa_start(struct zscom *zs) 2352 { 2353 register struct asyncline *za = (struct asyncline *)&zs->zs_priv_str; 2354 register int cc; 2355 register queue_t *q; 2356 register mblk_t *bp; 2357 uchar_t *rptr, *wptr; 2358 2359 /* 2360 * If the chip is busy (i.e., we're waiting for a break timeout 2361 * to expire, or for the current transmission to finish, or for 2362 * output to finish draining from chip), don't grab anything new. 2363 */ 2364 if ((za->za_flags & (ZAS_BREAK|ZAS_BUSY|ZAS_DRAINING)) || 2365 zs->zs_suspended) 2366 return; 2367 2368 if (za->za_ttycommon.t_cflag & CRTSCTS) { 2369 mutex_enter(zs->zs_excl_hi); 2370 if (za->za_rcv_flags_mask & DO_RETRANSMIT) { 2371 rptr = zs->zs_wr_cur; 2372 wptr = zs->zs_wr_lim; 2373 goto zsa_start_retransmit; 2374 2375 } 2376 mutex_exit(zs->zs_excl_hi); 2377 } 2378 2379 /* 2380 * If we have a flow-control character to transmit, do it now. 2381 */ 2382 if (za->za_flowc != '\0') { 2383 mutex_enter(zs->zs_excl_hi); 2384 if (za->za_ttycommon.t_cflag & CRTSCTS) { 2385 if ((SCC_READ0() & (ZSRR0_CTS|ZSRR0_TX_READY)) != 2386 (ZSRR0_CTS|ZSRR0_TX_READY)) { 2387 mutex_exit(zs->zs_excl_hi); 2388 return; 2389 } 2390 } else if (!(SCC_READ0() & ZSRR0_TX_READY)) { 2391 mutex_exit(zs->zs_excl_hi); 2392 return; 2393 } 2394 2395 ZSDELAY(); 2396 SCC_WRITEDATA(za->za_flowc); 2397 za->za_flowc = '\0'; 2398 mutex_exit(zs->zs_excl_hi); 2399 return; 2400 } 2401 2402 /* 2403 * If we're waiting for a delay timeout to expire, don't grab 2404 * anything new. 2405 */ 2406 if (za->za_flags & ZAS_DELAY) 2407 return; 2408 2409 if ((q = za->za_ttycommon.t_writeq) == NULL) 2410 return; /* not attached to a stream */ 2411 2412 zsa_start_again: 2413 for (;;) { 2414 if ((bp = getq(q)) == NULL) 2415 return; /* no data to transmit */ 2416 2417 /* 2418 * We have a message block to work on. 2419 * Check whether it's a break, a delay, or an ioctl (the latter 2420 * occurs if the ioctl in question was waiting for the output 2421 * to drain). If it's one of those, process it immediately. 2422 */ 2423 switch (bp->b_datap->db_type) { 2424 2425 case M_BREAK: 2426 /* 2427 * Set the break bit, and arrange for "zsa_restart" 2428 * to be called in 1/4 second; it will turn the 2429 * break bit off, and call "zsa_start" to grab 2430 * the next message. 2431 */ 2432 mutex_enter(zs->zs_excl_hi); 2433 SCC_BIS(5, ZSWR5_BREAK); 2434 mutex_exit(zs->zs_excl_hi); 2435 if (!za->za_zsa_restart_id) { 2436 za->za_zsa_restart_id = 2437 timeout(zsa_restart, zs, hz/4); 2438 } 2439 za->za_flags |= ZAS_BREAK; 2440 freemsg(bp); 2441 return; /* wait for this to finish */ 2442 2443 case M_DELAY: 2444 /* 2445 * Arrange for "zsa_restart" to be called when the 2446 * delay expires; it will turn MTS_DELAY off, 2447 * and call "zsa_start" to grab the next message. 2448 */ 2449 if (! za->za_zsa_restart_id) { 2450 za->za_zsa_restart_id = timeout(zsa_restart, 2451 zs, 2452 (int)(*(unsigned char *)bp->b_rptr + 6)); 2453 } 2454 za->za_flags |= ZAS_DELAY; 2455 freemsg(bp); 2456 return; /* wait for this to finish */ 2457 2458 case M_IOCTL: 2459 /* 2460 * This ioctl was waiting for the output ahead of 2461 * it to drain; obviously, it has. Do it, and 2462 * then grab the next message after it. 2463 */ 2464 zsa_ioctl(za, q, bp); 2465 continue; 2466 default: /* M_DATA */ 2467 goto zsa_start_transmit; 2468 } 2469 2470 } 2471 zsa_start_transmit: 2472 /* 2473 * We have data to transmit. If output is stopped, put 2474 * it back and try again later. 2475 */ 2476 if (za->za_flags & ZAS_STOPPED) { 2477 (void) putbq(q, bp); 2478 return; 2479 } 2480 2481 za->za_xmitblk = bp; 2482 rptr = bp->b_rptr; 2483 wptr = bp->b_wptr; 2484 cc = wptr - rptr; 2485 bp = bp->b_cont; 2486 if (bp != NULL) { 2487 za->za_xmitblk->b_cont = NULL; 2488 (void) putbq(q, bp); /* not done with this message yet */ 2489 } 2490 2491 if (rptr >= wptr) { 2492 freeb(za->za_xmitblk); 2493 za->za_xmitblk = NULL; 2494 goto zsa_start_again; 2495 } 2496 2497 /* 2498 * In 5-bit mode, the high order bits are used 2499 * to indicate character sizes less than five, 2500 * so we need to explicitly mask before transmitting 2501 */ 2502 if ((za->za_ttycommon.t_cflag & CSIZE) == CS5) { 2503 register unsigned char *p = rptr; 2504 register int cnt = cc; 2505 2506 while (cnt--) 2507 *p++ &= (unsigned char) 0x1f; 2508 } 2509 2510 /* 2511 * Set up this block for pseudo-DMA. 2512 */ 2513 2514 mutex_enter(zs->zs_excl_hi); 2515 zs->zs_wr_cur = rptr; 2516 zs->zs_wr_lim = wptr; 2517 2518 zsa_start_retransmit: 2519 za->za_rcv_flags_mask &= ~DO_TRANSMIT; 2520 if (za->za_ttycommon.t_cflag & CRTSCTS) { 2521 if ((SCC_READ0() & (ZSRR0_CTS|ZSRR0_TX_READY)) != 2522 (ZSRR0_CTS|ZSRR0_TX_READY)) { 2523 za->za_rcv_flags_mask |= DO_RETRANSMIT; 2524 za->za_flags |= ZAS_BUSY; 2525 mutex_exit(zs->zs_excl_hi); 2526 return; 2527 } 2528 za->za_rcv_flags_mask &= ~DO_RETRANSMIT; 2529 } else { 2530 if (!(SCC_READ0() & ZSRR0_TX_READY)) { 2531 za->za_flags |= ZAS_BUSY; 2532 mutex_exit(zs->zs_excl_hi); 2533 return; 2534 } 2535 } 2536 /* 2537 * If the transmitter is ready, shove the first 2538 * character out. 2539 */ 2540 ZSDELAY(); 2541 SCC_WRITEDATA(*rptr++); 2542 #ifdef ZSA_DEBUG 2543 za->za_wr++; 2544 #endif 2545 zs->zs_wr_cur = rptr; 2546 za->za_flags |= ZAS_BUSY; 2547 zs->zs_flags |= ZS_PROGRESS; 2548 mutex_exit(zs->zs_excl_hi); 2549 } 2550 2551 /* 2552 * Restart output on a line after a delay or break timer expired. 2553 */ 2554 static void 2555 zsa_restart(void *arg) 2556 { 2557 struct zscom *zs = arg; 2558 struct asyncline *za = (struct asyncline *)&zs->zs_priv_str; 2559 2560 /* 2561 * If break timer expired, turn off the break bit. 2562 */ 2563 mutex_enter(zs->zs_excl); 2564 if (!za->za_zsa_restart_id) { 2565 mutex_exit(zs->zs_excl); 2566 return; 2567 } 2568 za->za_zsa_restart_id = 0; 2569 if (za->za_flags & ZAS_BREAK) { 2570 mutex_enter(zs->zs_excl_hi); 2571 SCC_BIC(5, ZSWR5_BREAK); 2572 mutex_exit(zs->zs_excl_hi); 2573 } 2574 za->za_flags &= ~(ZAS_DELAY|ZAS_BREAK); 2575 if (za->za_ttycommon.t_writeq != NULL) 2576 zsa_start(zs); 2577 mutex_exit(zs->zs_excl); 2578 cv_broadcast(&zs->zs_flags_cv); 2579 } 2580 2581 /* 2582 * See if the receiver has any data after zs_tick delay 2583 */ 2584 static void 2585 zsa_kick_rcv(void *arg) 2586 { 2587 struct zscom *zs = arg; 2588 struct asyncline *za = (struct asyncline *)&zs->zs_priv_str; 2589 queue_t *q; 2590 int tmp; 2591 mblk_t *mp; 2592 uchar_t za_soft_active, za_kick_active; 2593 int allocbcount = 0; 2594 int do_ttycommon_qfull = 0; 2595 mblk_t *head = NULL, *tail = NULL; 2596 2597 mutex_enter(zs->zs_excl); 2598 if (za->za_kick_rcv_id == 0 || (zs->zs_flags & ZS_CLOSED)) { 2599 mutex_exit(zs->zs_excl); 2600 return; 2601 } 2602 za_soft_active = za->za_soft_active; 2603 za_kick_active = za->za_kick_active; 2604 q = za->za_ttycommon.t_readq; 2605 if (!q) { 2606 mutex_exit(zs->zs_excl); 2607 return; 2608 } 2609 mutex_enter(zs->zs_excl_hi); 2610 if (zs->zs_rd_cur) { 2611 ZSA_KICK_RCV; 2612 za->za_kick_rcv_count = tmp = ZA_KICK_RCV_COUNT; 2613 } else 2614 tmp = --za->za_kick_rcv_count; 2615 if (tmp > 0 || za_soft_active || za_kick_active) { 2616 mutex_exit(zs->zs_excl_hi); 2617 if (g_zsticks) 2618 za->za_kick_rcv_id = timeout(zsa_kick_rcv, 2619 zs, g_zsticks); 2620 else 2621 za->za_kick_rcv_id = timeout(zsa_kick_rcv, 2622 zs, zsticks[SPEED(za->za_ttycommon.t_cflag)]); 2623 if (za_soft_active || za_kick_active) { 2624 mutex_exit(zs->zs_excl); 2625 return; 2626 } 2627 } else { 2628 za->za_kick_rcv_id = 0; 2629 mutex_exit(zs->zs_excl_hi); 2630 } 2631 2632 2633 for (;;) { 2634 ZSA_SEEQ(mp); 2635 if (!mp) 2636 break; 2637 2638 allocbcount++; 2639 2640 if (mp->b_datap->db_type <= QPCTL) { 2641 if (!(canputnext(q))) { 2642 if (za->za_grace_flow_control >= 2643 zsa_grace_flow_control) { 2644 if (za->za_ttycommon.t_cflag & 2645 CRTSXOFF) { 2646 allocbcount--; 2647 break; 2648 } 2649 ZSA_GETQ(mp); 2650 freemsg(mp); 2651 do_ttycommon_qfull = 1; 2652 continue; 2653 } else 2654 za->za_grace_flow_control++; 2655 } else 2656 za->za_grace_flow_control = 0; 2657 } 2658 ZSA_GETQ(mp); 2659 if (!head) { 2660 head = mp; 2661 } else { 2662 if (!tail) 2663 tail = head; 2664 tail->b_next = mp; 2665 tail = mp; 2666 } 2667 } 2668 2669 if (allocbcount) 2670 ZSA_GETBLOCK(zs, allocbcount); 2671 2672 za->za_kick_active = 1; 2673 mutex_exit(zs->zs_excl); 2674 2675 if (do_ttycommon_qfull) { 2676 ttycommon_qfull(&za->za_ttycommon, q); 2677 mutex_enter(zs->zs_excl); 2678 zsa_start(zs); 2679 mutex_exit(zs->zs_excl); 2680 } 2681 2682 while (head) { 2683 if (!tail) { 2684 putnext(q, head); 2685 break; 2686 } 2687 mp = head; 2688 head = head->b_next; 2689 mp->b_next = NULL; 2690 putnext(q, mp); 2691 2692 } 2693 za->za_kick_active = 0; 2694 2695 if (zs->zs_flags & ZS_CLOSED) 2696 cv_broadcast(&zs->zs_flags_cv); 2697 } 2698 2699 /* 2700 * Retry an "ioctl", now that "bufcall" claims we may be able to allocate 2701 * the buffer we need. 2702 */ 2703 static void 2704 zsa_reioctl(void *arg) 2705 { 2706 struct asyncline *za = arg; 2707 struct zscom *zs = za->za_common; 2708 queue_t *q; 2709 mblk_t *mp; 2710 2711 /* 2712 * The bufcall is no longer pending. 2713 */ 2714 mutex_enter(zs->zs_excl); 2715 if (!za->za_wbufcid) { 2716 mutex_exit(zs->zs_excl); 2717 return; 2718 } 2719 za->za_wbufcid = 0; 2720 if ((q = za->za_ttycommon.t_writeq) == NULL) { 2721 mutex_exit(zs->zs_excl); 2722 return; 2723 } 2724 if ((mp = za->za_ttycommon.t_iocpending) != NULL) { 2725 /* 2726 * not pending any more 2727 */ 2728 za->za_ttycommon.t_iocpending = NULL; 2729 zsa_ioctl(za, q, mp); 2730 } 2731 mutex_exit(zs->zs_excl); 2732 } 2733 2734 /* 2735 * Process an "ioctl" message sent down to us. 2736 * Note that we don't need to get any locks until we are ready to access 2737 * the hardware. Nothing we access until then is going to be altered 2738 * outside of the STREAMS framework, so we should be safe. 2739 */ 2740 static void 2741 zsa_ioctl(struct asyncline *za, queue_t *wq, mblk_t *mp) 2742 { 2743 register struct zscom *zs = za->za_common; 2744 register struct iocblk *iocp; 2745 register unsigned datasize; 2746 int error; 2747 register mblk_t *tmp; 2748 2749 if (za->za_ttycommon.t_iocpending != NULL) { 2750 /* 2751 * We were holding an "ioctl" response pending the 2752 * availability of an "mblk" to hold data to be passed up; 2753 * another "ioctl" came through, which means that "ioctl" 2754 * must have timed out or been aborted. 2755 */ 2756 freemsg(za->za_ttycommon.t_iocpending); 2757 za->za_ttycommon.t_iocpending = NULL; 2758 } 2759 2760 iocp = (struct iocblk *)mp->b_rptr; 2761 2762 /* 2763 * The only way in which "ttycommon_ioctl" can fail is if the "ioctl" 2764 * requires a response containing data to be returned to the user, 2765 * and no mblk could be allocated for the data. 2766 * No such "ioctl" alters our state. Thus, we always go ahead and 2767 * do any state-changes the "ioctl" calls for. If we couldn't allocate 2768 * the data, "ttycommon_ioctl" has stashed the "ioctl" away safely, so 2769 * we just call "bufcall" to request that we be called back when we 2770 * stand a better chance of allocating the data. 2771 */ 2772 mutex_exit(zs->zs_excl); 2773 datasize = ttycommon_ioctl(&za->za_ttycommon, wq, mp, &error); 2774 mutex_enter(zs->zs_excl); 2775 if (za->za_ttycommon.t_flags & TS_SOFTCAR) 2776 zssoftCAR[zs->zs_unit] = 1; 2777 else 2778 zssoftCAR[zs->zs_unit] = 0; 2779 if (datasize != 0) { 2780 if (za->za_wbufcid) 2781 unbufcall(za->za_wbufcid); 2782 za->za_wbufcid = bufcall(datasize, BPRI_HI, zsa_reioctl, za); 2783 return; 2784 } 2785 2786 2787 if (error == 0) { 2788 /* 2789 * "ttycommon_ioctl" did most of the work; we just use the 2790 * data it set up. 2791 */ 2792 switch (iocp->ioc_cmd) { 2793 2794 case TCSETS: 2795 case TCSETSW: 2796 case TCSETSF: 2797 case TCSETA: 2798 case TCSETAW: 2799 case TCSETAF: 2800 mutex_enter(zs->zs_excl_hi); 2801 zsa_program(za, 1); 2802 zsa_set_za_rcv_flags_mask(za); 2803 mutex_exit(zs->zs_excl_hi); 2804 break; 2805 } 2806 } else if (error < 0) { 2807 /* 2808 * "ttycommon_ioctl" didn't do anything; we process it here. 2809 */ 2810 error = 0; 2811 2812 switch (iocp->ioc_cmd) { 2813 2814 case TCSBRK: 2815 error = miocpullup(mp, sizeof (int)); 2816 if (error != 0) 2817 break; 2818 2819 if (*(int *)mp->b_cont->b_rptr == 0) { 2820 /* 2821 * The delay ensures that a 3 byte transmit 2822 * fifo is empty. 2823 */ 2824 mutex_exit(zs->zs_excl); 2825 delay(ztdelay(SPEED(za->za_ttycommon.t_cflag))); 2826 mutex_enter(zs->zs_excl); 2827 2828 /* 2829 * Set the break bit, and arrange for 2830 * "zsa_restart" to be called in 1/4 second; 2831 * it will turn the break bit off, and call 2832 * "zsa_start" to grab the next message. 2833 */ 2834 mutex_enter(zs->zs_excl_hi); 2835 SCC_BIS(5, ZSWR5_BREAK); 2836 if (!za->za_zsa_restart_id) { 2837 mutex_exit(zs->zs_excl_hi); 2838 za->za_zsa_restart_id = 2839 timeout(zsa_restart, zs, hz / 4); 2840 mutex_enter(zs->zs_excl_hi); 2841 } 2842 za->za_flags |= ZAS_BREAK; 2843 mutex_exit(zs->zs_excl_hi); 2844 } 2845 break; 2846 2847 case TIOCSBRK: 2848 mutex_enter(zs->zs_excl_hi); 2849 SCC_BIS(5, ZSWR5_BREAK); 2850 mutex_exit(zs->zs_excl_hi); 2851 mioc2ack(mp, NULL, 0, 0); 2852 break; 2853 2854 case TIOCCBRK: 2855 mutex_enter(zs->zs_excl_hi); 2856 SCC_BIC(5, ZSWR5_BREAK); 2857 mutex_exit(zs->zs_excl_hi); 2858 mioc2ack(mp, NULL, 0, 0); 2859 break; 2860 2861 case TIOCMSET: 2862 case TIOCMBIS: 2863 case TIOCMBIC: { 2864 int mlines; 2865 2866 if (iocp->ioc_count == TRANSPARENT) { 2867 mcopyin(mp, NULL, sizeof (int), NULL); 2868 break; 2869 } 2870 2871 error = miocpullup(mp, sizeof (int)); 2872 if (error != 0) 2873 break; 2874 2875 mlines = *(int *)mp->b_cont->b_rptr; 2876 2877 mutex_enter(zs->zs_excl_hi); 2878 switch (iocp->ioc_cmd) { 2879 case TIOCMSET: 2880 (void) zsmctl(zs, dmtozs(mlines), DMSET); 2881 break; 2882 case TIOCMBIS: 2883 (void) zsmctl(zs, dmtozs(mlines), DMBIS); 2884 break; 2885 case TIOCMBIC: 2886 (void) zsmctl(zs, dmtozs(mlines), DMBIC); 2887 break; 2888 } 2889 mutex_exit(zs->zs_excl_hi); 2890 2891 mioc2ack(mp, NULL, 0, 0); 2892 break; 2893 } 2894 2895 case TIOCMGET: 2896 tmp = allocb(sizeof (int), BPRI_MED); 2897 if (tmp == NULL) { 2898 error = EAGAIN; 2899 break; 2900 } 2901 if (iocp->ioc_count != TRANSPARENT) 2902 mioc2ack(mp, tmp, sizeof (int), 0); 2903 else 2904 mcopyout(mp, NULL, sizeof (int), NULL, tmp); 2905 2906 mutex_enter(zs->zs_excl_hi); 2907 *(int *)mp->b_cont->b_rptr = 2908 zstodm(zsmctl(zs, 0, DMGET)); 2909 mutex_exit(zs->zs_excl_hi); 2910 /* 2911 * qreply done below 2912 */ 2913 break; 2914 2915 default: 2916 /* 2917 * If we don't understand it, it's an error. NAK it. 2918 */ 2919 error = EINVAL; 2920 break; 2921 } 2922 } 2923 2924 if (error != 0) { 2925 iocp->ioc_error = error; 2926 mp->b_datap->db_type = M_IOCNAK; 2927 } 2928 2929 ZSA_QREPLY(wq, mp); 2930 } 2931 2932 2933 static int 2934 dmtozs(int bits) 2935 { 2936 register int b = 0; 2937 2938 if (bits & TIOCM_CAR) 2939 b |= ZSRR0_CD; 2940 if (bits & TIOCM_CTS) 2941 b |= ZSRR0_CTS; 2942 if (bits & TIOCM_RTS) 2943 b |= ZSWR5_RTS; 2944 if (bits & TIOCM_DTR) 2945 b |= ZSWR5_DTR; 2946 return (b); 2947 } 2948 2949 static int 2950 zstodm(int bits) 2951 { 2952 register int b; 2953 2954 b = 0; 2955 if (bits & ZSRR0_CD) 2956 b |= TIOCM_CAR; 2957 if (bits & ZSRR0_CTS) 2958 b |= TIOCM_CTS; 2959 if (bits & ZSWR5_RTS) 2960 b |= TIOCM_RTS; 2961 if (bits & ZSWR5_DTR) 2962 b |= TIOCM_DTR; 2963 return (b); 2964 } 2965 2966 /* 2967 * Assemble registers and flags necessary to program the port to our liking. 2968 * For async operation, most of this is based on the values of 2969 * the "c_iflag" and "c_cflag" fields supplied to us. 2970 */ 2971 static void 2972 zsa_program(struct asyncline *za, int setibaud) 2973 { 2974 register struct zscom *zs = za->za_common; 2975 register struct zs_prog *zspp; 2976 register int wr3, wr4, wr5, wr15, speed, baudrate, flags = 0; 2977 2978 if ((baudrate = SPEED(za->za_ttycommon.t_cflag)) == 0) { 2979 /* 2980 * Hang up line. 2981 */ 2982 (void) zsmctl(zs, ZS_OFF, DMSET); 2983 return; 2984 } 2985 2986 /* 2987 * set input speed same as output, as split speed not supported 2988 */ 2989 if (setibaud) { 2990 za->za_ttycommon.t_cflag &= ~(CIBAUD); 2991 if (baudrate > CBAUD) { 2992 za->za_ttycommon.t_cflag |= CIBAUDEXT; 2993 za->za_ttycommon.t_cflag |= 2994 (((baudrate - CBAUD - 1) << IBSHIFT) & CIBAUD); 2995 } else { 2996 za->za_ttycommon.t_cflag &= ~CIBAUDEXT; 2997 za->za_ttycommon.t_cflag |= 2998 ((baudrate << IBSHIFT) & CIBAUD); 2999 } 3000 } 3001 3002 /* 3003 * Do not allow the console/keyboard device to have its receiver 3004 * disabled; doing that would mean you couldn't type an abort 3005 * sequence. 3006 */ 3007 if ((za->za_dev == rconsdev) || (za->za_dev == kbddev) || 3008 (za->za_dev == stdindev) || (za->za_ttycommon.t_cflag & CREAD)) 3009 wr3 = ZSWR3_RX_ENABLE; 3010 else 3011 wr3 = 0; 3012 wr4 = ZSWR4_X16_CLK; 3013 wr5 = (zs->zs_wreg[5] & (ZSWR5_RTS|ZSWR5_DTR)) | ZSWR5_TX_ENABLE; 3014 3015 if (zsb134_weird && baudrate == B134) { /* what a joke! */ 3016 /* 3017 * XXX - should B134 set all this crap in the compatibility 3018 * module, leaving this stuff fairly clean? 3019 */ 3020 flags |= ZSP_PARITY_SPECIAL; 3021 wr3 |= ZSWR3_RX_6; 3022 wr4 |= ZSWR4_PARITY_ENABLE | ZSWR4_PARITY_EVEN; 3023 wr4 |= ZSWR4_1_5_STOP; 3024 wr5 |= ZSWR5_TX_6; 3025 } else { 3026 3027 switch (za->za_ttycommon.t_cflag & CSIZE) { 3028 3029 case CS5: 3030 wr3 |= ZSWR3_RX_5; 3031 wr5 |= ZSWR5_TX_5; 3032 break; 3033 3034 case CS6: 3035 wr3 |= ZSWR3_RX_6; 3036 wr5 |= ZSWR5_TX_6; 3037 break; 3038 3039 case CS7: 3040 wr3 |= ZSWR3_RX_7; 3041 wr5 |= ZSWR5_TX_7; 3042 break; 3043 3044 case CS8: 3045 wr3 |= ZSWR3_RX_8; 3046 wr5 |= ZSWR5_TX_8; 3047 break; 3048 } 3049 3050 if (za->za_ttycommon.t_cflag & PARENB) { 3051 /* 3052 * The PARITY_SPECIAL bit causes a special rx 3053 * interrupt on parity errors. Turn it on if 3054 * we're checking the parity of characters. 3055 */ 3056 if (za->za_ttycommon.t_iflag & INPCK) 3057 flags |= ZSP_PARITY_SPECIAL; 3058 wr4 |= ZSWR4_PARITY_ENABLE; 3059 if (!(za->za_ttycommon.t_cflag & PARODD)) 3060 wr4 |= ZSWR4_PARITY_EVEN; 3061 } 3062 wr4 |= (za->za_ttycommon.t_cflag & CSTOPB) ? 3063 ZSWR4_2_STOP : ZSWR4_1_STOP; 3064 } 3065 3066 #if 0 3067 /* 3068 * The AUTO_CD_CTS flag enables the hardware flow control feature of 3069 * the 8530, which allows the state of CTS and DCD to control the 3070 * enabling of the transmitter and receiver, respectively. The 3071 * receiver and transmitter still must have their enable bits set in 3072 * WR3 and WR5, respectively, for CTS and DCD to be monitored this way. 3073 * Hardware flow control can thus be implemented with no help from 3074 * software. 3075 */ 3076 if (za->za_ttycommon.t_cflag & CRTSCTS) 3077 wr3 |= ZSWR3_AUTO_CD_CTS; 3078 #endif 3079 if (za->za_ttycommon.t_cflag & CRTSCTS) 3080 wr15 = ZSR15_BREAK | ZSR15_TX_UNDER | ZSR15_CD | ZSR15_CTS; 3081 else 3082 wr15 = ZSR15_BREAK | ZSR15_TX_UNDER | ZSR15_CD; 3083 3084 speed = zs->zs_wreg[12] + (zs->zs_wreg[13] << 8); 3085 3086 /* 3087 * Here we assemble a set of changes to be passed to zs_program. 3088 * Note: Write Register 15 must be set to enable BREAK and UNDERrun 3089 * interrupts. It must also enable CD interrupts which, although 3090 * not processed by the hardware interrupt handler, will be processed 3091 * by zsa_process, indirectly resulting in a SIGHUP being delivered 3092 * to the controlling process if CD drops. CTS interrupts must NOT 3093 * be enabled. We don't use them at all, and they will hang IPC/IPX 3094 * systems at boot time if synchronous modems that supply transmit 3095 * clock are attached to any of their serial ports. 3096 */ 3097 if (((zs->zs_wreg[1] & ZSWR1_PARITY_SPECIAL) && 3098 !(flags & ZSP_PARITY_SPECIAL)) || 3099 (!(zs->zs_wreg[1] & ZSWR1_PARITY_SPECIAL) && 3100 (flags & ZSP_PARITY_SPECIAL)) || 3101 wr3 != zs->zs_wreg[3] || wr4 != zs->zs_wreg[4] || 3102 wr5 != zs->zs_wreg[5] || wr15 != zs->zs_wreg[15] || 3103 speed != zs_speeds[baudrate]) { 3104 3105 za->za_flags |= ZAS_DRAINING; 3106 zspp = &zs_prog[zs->zs_unit]; 3107 zspp->zs = zs; 3108 zspp->flags = (uchar_t)flags; 3109 zspp->wr4 = (uchar_t)wr4; 3110 zspp->wr11 = (uchar_t)(ZSWR11_TXCLK_BAUD | ZSWR11_RXCLK_BAUD); 3111 3112 speed = zs_speeds[baudrate]; 3113 zspp->wr12 = (uchar_t)(speed & 0xff); 3114 zspp->wr13 = (uchar_t)((speed >> 8) & 0xff); 3115 zspp->wr3 = (uchar_t)wr3; 3116 zspp->wr5 = (uchar_t)wr5; 3117 zspp->wr15 = (uchar_t)wr15; 3118 3119 zs_program(zspp); 3120 za->za_flags &= ~ZAS_DRAINING; 3121 } 3122 } 3123 3124 /* 3125 * Get the current speed of the console and turn it into something 3126 * UNIX knows about - used to preserve console speed when UNIX comes up. 3127 */ 3128 int 3129 zsgetspeed(dev_t dev) 3130 { 3131 register struct zscom *zs; 3132 register int uspeed, zspeed; 3133 register uchar_t rr; 3134 3135 zs = &zscom[UNIT(dev)]; 3136 SCC_READ(12, zspeed); 3137 SCC_READ(13, rr); 3138 zspeed |= rr << 8; 3139 for (uspeed = 0; uspeed < NSPEED; uspeed++) 3140 if (zs_speeds[uspeed] == zspeed) 3141 return (uspeed); 3142 /* 3143 * 9600 baud if we can't figure it out 3144 */ 3145 return (ISPEED); 3146 } 3147 3148 /* 3149 * callback routine when enough memory is available. 3150 */ 3151 static void 3152 zsa_callback(void *arg) 3153 { 3154 struct zscom *zs = arg; 3155 struct asyncline *za = (struct asyncline *)&zs->zs_priv_str; 3156 int allocbcount = zsa_rstandby; 3157 3158 mutex_enter(zs->zs_excl); 3159 if (za->za_bufcid) { 3160 za->za_bufcid = 0; 3161 ZSA_GETBLOCK(zs, allocbcount); 3162 } 3163 mutex_exit(zs->zs_excl); 3164 } 3165 3166 /* 3167 * Set the receiver flags 3168 */ 3169 static void 3170 zsa_set_za_rcv_flags_mask(struct asyncline *za) 3171 { 3172 register uint_t mask; 3173 3174 za->za_rcv_flags_mask &= ~0xFF; 3175 switch (za->za_ttycommon.t_cflag & CSIZE) { 3176 case CS5: 3177 mask = 0x1f; 3178 break; 3179 case CS6: 3180 mask = 0x3f; 3181 break; 3182 case CS7: 3183 mask = 0x7f; 3184 break; 3185 default: 3186 mask = 0xff; 3187 } 3188 3189 za->za_rcv_flags_mask &= ~(0xFF << 16); 3190 za->za_rcv_flags_mask |= mask << 16; 3191 3192 if ((za->za_ttycommon.t_iflag & PARMRK) && 3193 !(za->za_ttycommon.t_iflag & (IGNPAR|ISTRIP))) { 3194 za->za_rcv_flags_mask |= DO_ESC; 3195 } else 3196 za->za_rcv_flags_mask &= ~DO_ESC; 3197 if (za->za_ttycommon.t_iflag & IXON) { 3198 za->za_rcv_flags_mask |= DO_STOPC; 3199 za->za_rcv_flags_mask &= ~0xFF; 3200 za->za_rcv_flags_mask |= za->za_ttycommon.t_stopc; 3201 } else 3202 za->za_rcv_flags_mask &= ~DO_STOPC; 3203 } 3204 3205 static int 3206 zsa_suspend(struct zscom *zs) 3207 { 3208 struct asyncline *za; 3209 queue_t *q; 3210 mblk_t *bp = NULL; 3211 timeout_id_t restart_id, kick_rcv_id; 3212 struct zs_prog *zspp; 3213 3214 za = (struct asyncline *)&zs->zs_priv_str; 3215 mutex_enter(zs->zs_excl); 3216 if (zs->zs_suspended) { 3217 mutex_exit(zs->zs_excl); 3218 return (DDI_SUCCESS); 3219 } 3220 zs->zs_suspended = 1; 3221 3222 /* 3223 * Turn off interrupts and get any bytes in receiver 3224 */ 3225 mutex_enter(zs->zs_excl_hi); 3226 SCC_BIC(1, ZSWR1_INIT); 3227 ZSA_KICK_RCV; 3228 restart_id = za->za_zsa_restart_id; 3229 za->za_zsa_restart_id = 0; 3230 kick_rcv_id = za->za_kick_rcv_id; 3231 za->za_kick_rcv_id = 0; 3232 mutex_exit(zs->zs_excl_hi); 3233 mutex_exit(zs->zs_excl); 3234 3235 /* 3236 * Cancel any timeouts 3237 */ 3238 if (restart_id) 3239 (void) untimeout(restart_id); 3240 if (kick_rcv_id) 3241 (void) untimeout(kick_rcv_id); 3242 3243 /* 3244 * Since we have turned off interrupts, zsa_txint will not be called 3245 * and no new chars will given to the chip. We just wait for the 3246 * current character(s) to drain. 3247 */ 3248 delay(ztdelay(za->za_ttycommon.t_cflag & CBAUD)); 3249 3250 /* 3251 * Return remains of partially sent message to queue 3252 */ 3253 mutex_enter(zs->zs_excl); 3254 if ((q = za->za_ttycommon.t_writeq) != NULL) { 3255 mutex_enter(zs->zs_excl_hi); 3256 if ((zs->zs_wr_cur) != NULL) { 3257 za->za_flags &= ~ZAS_BUSY; 3258 za->za_rcv_flags_mask &= ~DO_RETRANSMIT; 3259 bp = za->za_xmitblk; 3260 bp->b_rptr = zs->zs_wr_cur; 3261 zs->zs_wr_cur = NULL; 3262 zs->zs_wr_lim = NULL; 3263 za->za_xmitblk = NULL; 3264 } 3265 mutex_exit(zs->zs_excl_hi); 3266 if (bp) 3267 (void) putbq(q, bp); 3268 } 3269 3270 /* 3271 * Stop any breaks in progress. 3272 */ 3273 mutex_enter(zs->zs_excl_hi); 3274 if (zs->zs_wreg[5] & ZSWR5_BREAK) { 3275 SCC_BIC(5, ZSWR5_BREAK); 3276 za->za_flags &= ~ZAS_BREAK; 3277 } 3278 3279 /* 3280 * Now get a copy of current registers setting. 3281 */ 3282 zspp = &zs_prog[zs->zs_unit]; 3283 zspp->zs = zs; 3284 zspp->flags = 0; 3285 zspp->wr3 = zs->zs_wreg[3]; 3286 zspp->wr4 = zs->zs_wreg[4]; 3287 zspp->wr5 = zs->zs_wreg[5]; 3288 zspp->wr11 = zs->zs_wreg[11]; 3289 zspp->wr12 = zs->zs_wreg[12]; 3290 zspp->wr13 = zs->zs_wreg[13]; 3291 zspp->wr15 = zs->zs_wreg[15]; 3292 mutex_exit(zs->zs_excl_hi); 3293 mutex_exit(zs->zs_excl); 3294 /* 3295 * We do this on the off chance that zsa_close is waiting on a timed 3296 * break to complete and nothing else. 3297 */ 3298 cv_broadcast(&zs->zs_flags_cv); 3299 return (DDI_SUCCESS); 3300 } 3301 3302 static int 3303 zsa_resume(struct zscom *zs) 3304 { 3305 register struct asyncline *za; 3306 struct zs_prog *zspp; 3307 3308 za = (struct asyncline *)&zs->zs_priv_str; 3309 mutex_enter(zs->zs_excl); 3310 if (!(zs->zs_suspended)) { 3311 mutex_exit(zs->zs_excl); 3312 return (DDI_SUCCESS); 3313 } 3314 3315 /* 3316 * Restore H/W state 3317 */ 3318 mutex_enter(zs->zs_excl_hi); 3319 zspp = &zs_prog[zs->zs_unit]; 3320 zs_program(zspp); 3321 3322 /* 3323 * Enable all interrupts for this chip and delay to let chip settle 3324 */ 3325 SCC_WRITE(9, ZSWR9_MASTER_IE | ZSWR9_VECTOR_INCL_STAT); 3326 DELAY(4000); 3327 3328 /* 3329 * Restart receiving and transmitting 3330 */ 3331 zs->zs_suspended = 0; 3332 za->za_rcv_flags_mask |= DO_TRANSMIT; 3333 za->za_ext = 1; 3334 ZSSETSOFT(zs); 3335 mutex_exit(zs->zs_excl_hi); 3336 mutex_exit(zs->zs_excl); 3337 3338 return (DDI_SUCCESS); 3339 } 3340 3341 #ifdef ZSA_DEBUG 3342 static void 3343 zsa_print_info(struct zscom *zs) 3344 { 3345 register struct asyncline *za = (struct asyncline *)&zs->zs_priv_str; 3346 register queue_t *q = za->za_ttycommon.t_writeq; 3347 3348 printf(" next q=%s\n", (RD(q))->q_next->q_qinfo->qi_minfo->mi_idname); 3349 printf("unit=%d\n", zs->zs_unit); 3350 printf("tflag:\n"); 3351 if (za->za_ttycommon.t_flags & TS_SOFTCAR) printf(" t_fl:TS_SOFTCAR"); 3352 if (za->za_ttycommon.t_flags & TS_XCLUDE) printf(" t_fl:TS_XCLUDE"); 3353 if (za->za_ttycommon.t_iflag & IGNBRK) printf(" t_ifl:IGNBRK"); 3354 if (za->za_ttycommon.t_iflag & BRKINT) printf(" t_ifl:BRKINT"); 3355 if (za->za_ttycommon.t_iflag & IGNPAR) printf(" t_ifl:IGNPAR"); 3356 if (za->za_ttycommon.t_iflag & PARMRK) printf(" t_ifl:PARMRK"); 3357 if (za->za_ttycommon.t_iflag & INPCK) printf(" t_ifl:INPCK"); 3358 if (za->za_ttycommon.t_iflag & ISTRIP) printf(" t_ifl:ISTRIP"); 3359 if (za->za_ttycommon.t_iflag & INLCR) printf(" t_ifl:INLCR"); 3360 if (za->za_ttycommon.t_iflag & IGNCR) printf(" t_ifl:IGNCR"); 3361 if (za->za_ttycommon.t_iflag & ICRNL) printf(" t_ifl:ICRNL"); 3362 if (za->za_ttycommon.t_iflag & IUCLC) printf(" t_ifl:IUCLC"); 3363 if (za->za_ttycommon.t_iflag & IXON) printf(" t_ifl:IXON"); 3364 if (za->za_ttycommon.t_iflag & IXOFF) printf(" t_ifl:IXOFF"); 3365 3366 printf("\n"); 3367 3368 3369 if (za->za_ttycommon.t_cflag & CSIZE == CS5) printf(" t_cfl:CS5"); 3370 if (za->za_ttycommon.t_cflag & CSIZE == CS6) printf(" t_cfl:CS6"); 3371 if (za->za_ttycommon.t_cflag & CSIZE == CS7) printf(" t_cfl:CS7"); 3372 if (za->za_ttycommon.t_cflag & CSIZE == CS8) printf(" t_cfl:CS8"); 3373 if (za->za_ttycommon.t_cflag & CSTOPB) printf(" t_cfl:CSTOPB"); 3374 if (za->za_ttycommon.t_cflag & CREAD) printf(" t_cfl:CREAD"); 3375 if (za->za_ttycommon.t_cflag & PARENB) printf(" t_cfl:PARENB"); 3376 if (za->za_ttycommon.t_cflag & PARODD) printf(" t_cfl:PARODD"); 3377 if (za->za_ttycommon.t_cflag & HUPCL) printf(" t_cfl:HUPCL"); 3378 if (za->za_ttycommon.t_cflag & CLOCAL) printf(" t_cfl:CLOCAL"); 3379 printf(" t_stopc=%x", za->za_ttycommon.t_stopc); 3380 printf("\n"); 3381 } 3382 #endif 3383 3384 /* 3385 * Check for abort character sequence 3386 */ 3387 static boolean_t 3388 abort_charseq_recognize(uchar_t ch) 3389 { 3390 static int state = 0; 3391 #define CNTRL(c) ((c)&037) 3392 static char sequence[] = { '\r', '~', CNTRL('b') }; 3393 3394 if (ch == sequence[state]) { 3395 if (++state >= sizeof (sequence)) { 3396 state = 0; 3397 return (B_TRUE); 3398 } 3399 } else { 3400 state = (ch == sequence[0]) ? 1 : 0; 3401 } 3402 return (B_FALSE); 3403 } 3404