1# 2# CDDL HEADER START 3# 4# The contents of this file are subject to the terms of the 5# Common Development and Distribution License (the "License"). 6# You may not use this file except in compliance with the License. 7# 8# You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE 9# or http://www.opensolaris.org/os/licensing. 10# See the License for the specific language governing permissions 11# and limitations under the License. 12# 13# When distributing Covered Code, include this CDDL HEADER in each 14# file and include the License file at usr/src/OPENSOLARIS.LICENSE. 15# If applicable, add the following below this CDDL HEADER, with the 16# fields enclosed by brackets "[]" replaced with your own identifying 17# information: Portions Copyright [yyyy] [name of copyright owner] 18# 19# CDDL HEADER END 20# 21# 22# Copyright 2006 Sun Microsystems, Inc. All rights reserved. 23# Use is subject to license terms. 24# 25 26# 27# The officially supported devices do not require a entry under 28# tape-config-list as their configuration is built in to the driver. 29# 30# 31# A non configured drive will say Unconfigured Drive: and have single quoted 32# Vendor and Product strings displayed when its status is checked with mt. 33# 34# mt -f /dev/rmt/# status 35# Unconfigured Drive: Vendor 'VENDOR ' Product 'A Product ID ' 36# sense key(0x0)= No Additional Sense residual= 0 retries= 0 37# file no= 0 block no= 0 38# 39# If your drive is displayed like this first check to see if a newer version 40# of the st driver has added support for your drive. 41# 42# If your drive is not supported by Sun, check the drive manufacturer's 43# documentation or web site for their recommended configuration strings. 44# 45# To configure a drive not supported by the driver, use the single quoted 46# Vendor and Product strings to create a entry under tape-config-list. 47# 48# A starting point for your st.conf entry can be obtained by reading the 49# current DEFAULT configuration from the driver using mt. 50# 51# mt -f /dev/rmt/# config 52# "SONY SDX-700C", "SONY SDX-700C", "SONYSDX700C"; 53# SONYSDX700C = \ 54# 2,0x12,0,0x1865B,4,0x00,0x00,0x00,0x00,0,120,120,3600,3600,3600,3600,3600; 55# 56# 57# Notes: 58# Any spaces in the Vendor field must be kept so that it is 8 59# characters long. Trailing spaces in the Product field can be removed. 60# 61# To add this configuration information, first uncomment the 62# "tape-config-list=" line, and add the first configuration line 63# immediately afterward. If there is more than one entry in the 64# tape-config-list, all entries but the last must end with a comma. 65# The last entry ends with a semicolon. 66# 67# See the driver.conf(5) man page for general information on the conf 68# file format, and the st(4D) man page for information specific to st.conf. 69# 70# Example: 71#tape-config-list= 72# "VENDOR A Product ID", "A Prettier Name to Display", "A-Config-Name", 73# "VENDORB Other Product ID", "An Other Pretty Name", "Other-Config-Name"; 74# 75# Then for each config-Name there must be a setup string that looks like this. 76# 77# A-Config-Name = \ 78# 2,0x34,0,0x18659,4,0x47,0x47,0x47,0x47,1,120,120,3600,3600,3600,3600,3600; 79# Other-Config-Name = 1,0x3B,0,0x18659,4,0x40,0x40,0x40,0x40,3; 80# 81# For specific details for of values to use see the st(4D) man pages and 82# drive vendor manuals. 83# 84 85 86 87name="st" class="scsi" target=0 lun=0; 88name="st" class="scsi" target=1 lun=0; 89name="st" class="scsi" target=2 lun=0; 90name="st" class="scsi" target=3 lun=0; 91name="st" class="scsi" target=4 lun=0; 92name="st" class="scsi" target=5 lun=0; 93name="st" class="scsi" target=6 lun=0; 94 95# 96# In case there are wide tape drives, one can use these targets 97# 98#name="st" class="scsi" target=8 lun=0; 99#name="st" class="scsi" target=9 lun=0; 100#name="st" class="scsi" target=10 lun=0; 101#name="st" class="scsi" target=11 lun=0; 102#name="st" class="scsi" target=12 lun=0; 103#name="st" class="scsi" target=13 lun=0; 104#name="st" class="scsi" target=14 lun=0; 105#name="st" class="scsi" target=15 lun=0; 106 107# This line adds support for Fibre Channel Tapes 108name="st" parent="fp" target=0; 109