1# 2# CDDL HEADER START 3# 4# The contents of this file are subject to the terms of the 5# Common Development and Distribution License (the "License"). 6# You may not use this file except in compliance with the License. 7# 8# You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE 9# or http://www.opensolaris.org/os/licensing. 10# See the License for the specific language governing permissions 11# and limitations under the License. 12# 13# When distributing Covered Code, include this CDDL HEADER in each 14# file and include the License file at usr/src/OPENSOLARIS.LICENSE. 15# If applicable, add the following below this CDDL HEADER, with the 16# fields enclosed by brackets "[]" replaced with your own identifying 17# information: Portions Copyright [yyyy] [name of copyright owner] 18# 19# CDDL HEADER END 20# 21# 22# Copyright 2006 Sun Microsystems, Inc. All rights reserved. 23# Use is subject to license terms. 24# 25 26# 27#pragma ident "%Z%%M% %I% %E% SMI" 28# 29 30# 31# The officially supported devices do not require a entry under 32# tape-config-list as their configuration is built in to the driver. 33# 34# 35# A non configured drive will say Unconfigured Drive: and have single quoted 36# Vendor and Product strings displayed when its status is checked with mt. 37# 38# mt -f /dev/rmt/# status 39# Unconfigured Drive: Vendor 'VENDOR ' Product 'A Product ID ' 40# sense key(0x0)= No Additional Sense residual= 0 retries= 0 41# file no= 0 block no= 0 42# 43# If your drive is displayed like this first check to see if a newer version 44# of the st driver has added support for your drive. 45# 46# If your drive is not supported by Sun, check the drive manufacturer's 47# documentation or web site for their recommended configuration strings. 48# 49# To configure a drive not supported by the driver, use the single quoted 50# Vendor and Product strings to create a entry under tape-config-list. 51# 52# A starting point for your st.conf entry can be obtained by reading the 53# current DEFAULT configuration from the driver using mt. 54# 55# mt -f /dev/rmt/# config 56# "SONY SDX-700C", "SONY SDX-700C", "SONYSDX700C"; 57# SONYSDX700C = \ 58# 2,0x12,0,0x1865B,4,0x00,0x00,0x00,0x00,0,120,120,3600,3600,3600,3600,3600; 59# 60# 61# Notes: 62# Any spaces in the Vendor field must be kept so that it is 8 63# characters long. Trailing spaces in the Product field can be removed. 64# 65# To add this configuration information, first uncomment the 66# "tape-config-list=" line, and add the first configuration line 67# immediately afterward. If there is more than one entry in the 68# tape-config-list, all entries but the last must end with a comma. 69# The last entry ends with a semicolon. 70# 71# See the driver.conf(4) man page for general information on the conf 72# file format, and the st(7d) man page for information specific to st.conf. 73# 74# Example: 75#tape-config-list= 76# "VENDOR A Product ID", "A Prettier Name to Display", "A-Config-Name", 77# "VENDORB Other Product ID", "An Other Pretty Name", "Other-Config-Name"; 78# 79# Then for each config-Name there must be a setup string that looks like this. 80# 81# A-Config-Name = \ 82# 2,0x34,0,0x18659,4,0x47,0x47,0x47,0x47,1,120,120,3600,3600,3600,3600,3600; 83# Other-Config-Name = 1,0x3B,0,0x18659,4,0x40,0x40,0x40,0x40,3; 84# 85# For specific details for of values to use see the st(7D) man pages and 86# drive vendor manuals. 87# 88 89 90 91name="st" class="scsi" target=0 lun=0; 92name="st" class="scsi" target=1 lun=0; 93name="st" class="scsi" target=2 lun=0; 94name="st" class="scsi" target=3 lun=0; 95name="st" class="scsi" target=4 lun=0; 96name="st" class="scsi" target=5 lun=0; 97name="st" class="scsi" target=6 lun=0; 98 99# 100# In case there are wide tape drives, one can use these targets 101# 102#name="st" class="scsi" target=8 lun=0; 103#name="st" class="scsi" target=9 lun=0; 104#name="st" class="scsi" target=10 lun=0; 105#name="st" class="scsi" target=11 lun=0; 106#name="st" class="scsi" target=12 lun=0; 107#name="st" class="scsi" target=13 lun=0; 108#name="st" class="scsi" target=14 lun=0; 109#name="st" class="scsi" target=15 lun=0; 110 111# This line adds support for Fibre Channel Tapes 112name="st" parent="fp" target=0; 113