Copyright (c) 1999, Sun Microsystems, Inc. All Rights Reserved
The contents of this file are subject to the terms of the Common Development and Distribution License (the "License"). You may not use this file except in compliance with the License.
You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE or http://www.opensolaris.org/os/licensing. See the License for the specific language governing permissions and limitations under the License.
When distributing Covered Code, include this CDDL HEADER in each file and include the License file at usr/src/OPENSOLARIS.LICENSE. If applicable, add the following below this CDDL HEADER, with the fields enclosed by brackets "[]" replaced with your own identifying information: Portions Copyright [yyyy] [name of copyright owner]
#include <sys/ddi.h> #include <sys/sunddi.h> void ddi_dev_report_fault (dev_info_t *dip, ddi_fault_impact_t impact, ddi_fault_location_t location, const char *message );
Pointer to the driver's dev_info structure to which the fault report relates. (Normally the caller's own dev_info pointer).
One of a set of enumerated values indicating the impact of the fault on the device's ability to provide normal service.
One of a set of enumerated values indicating the location of the fault, relative to the hardware controlled by the driver specified by dip.
Text of the message describing the fault being reported.
The driver must indicate the impact of the fault being reported on its ability to provide service by passing one of the following values for the impact parameter: DDI_SERVICE_LOST
Indicates a total loss of service. The driver is unable to implement the normal functions of its hardware.
The driver is unable to provide normal service, but can provide a partial or degraded level of service. The driver may have to make repeated attempts to perform an operation before it succeeds, or it may be running at less than its configured speed. A driver may use this value to indicate that an alternative device should be used if available, but that it can continue operation if no alternative exists.
The service provided by the device is currently unaffected by the reported fault. This value may be used to report recovered errors for predictive failure analysis.
The driver has resumed normal service, following a previous report that service was lost or degraded. This message implies that any previously reported fault condition no longer exists.
The location parameter should be one of the following values: DDI_DATAPATH_FAULT
The fault lies in the datapath between the driver and the device. The device may be unplugged, or a problem may exist in the bus on which the device resides. This value is appropriate if the device is not responding to accesses, (for example, the device may not be present) or if a call to ddi_check_acc_handle(9F) returns DDI_FAILURE.
The fault lies in the device controlled by the driver. This value is appropriate if the device returns an error from a selftest function, or if the driver is able to determine that device is present and accessible, but is not functioning correctly.
The fault is external to the device. For example, an Ethernet driver would use this value when reporting a cable fault. If a device returns detectably bad data during normal operation (an "impossible" value in a register or DMA status area, for example), the driver should check the associated handle using ddi_check_acc_handle(9F) or ddi_check_dma_handle(9F) before reporting the fault. If the fault is associated with the handle, the driver should specify DDI_DATAPATH_FAULT rather than DDI_DEVICE_FAULT. As a consequence of this call, the device's state may be updated to reflect the level of service currently available. See ddi_get_devstate(9F). Note that if a driver calls ddi_get_devstate(9F) and discovers that its device is down, a fault should not be reported- the device is down as the result of a fault that has already been reported. Additionally, a driver should avoid incurring or reporting additional faults when the device is already known to be unusable. The ddi_dev_report_fault() call should only be used to report hardware (device) problems and should not be used to report purely software problems such as memory (or other resource) exhaustion.
static int
xx_error_intr(xx_soft_state *ssp)
{
...
error_status = ddi_get32(ssp->handle, &ssp->regs->xx_err_status);
if (ddi_check_acc_handle(ssp->handle) != DDI_SUCCESS) {
ddi_dev_report_fault(ssp->dip, DDI_SERVICE_LOST,
DDI_DATAPATH_FAULT, "register access fault");
return DDI_INTR_UNCLAIMED;
}
if (ssp->error_status & XX_CABLE_FAULT) {
ddi_dev_report_fault(ssp->dip, DDI_SERVICE_LOST,
DDI_EXTERNAL_FAULT, "cable fault")
return DDI_INTR_CLAIMED;
}
if (ssp->error_status & XX_JABBER) {
ddi_dev_report_fault(ssp->dip, DDI_SERVICE_DEGRADED,
DDI_EXTERNAL_FAULT, "jabbering detected")
return DDI_INTR_CLAIMED;
}
...
}