Copyright (c) 2001 Sun Microsystems, Inc. All Rights Reserved.
Copyright 1989 AT&T
The contents of this file are subject to the terms of the Common Development and Distribution License (the "License"). You may not use this file except in compliance with the License.
You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE or http://www.opensolaris.org/os/licensing. See the License for the specific language governing permissions and limitations under the License.
When distributing Covered Code, include this CDDL HEADER in each file and include the License file at usr/src/OPENSOLARIS.LICENSE. If applicable, add the following below this CDDL HEADER, with the fields enclosed by brackets "[]" replaced with your own identifying information: Portions Copyright [yyyy] [name of copyright owner]
/usr/sbin/shutdown [-y] [-g grace-period] [-i init-state] [message]
shutdown is executed by the super user to change the state of the machine. In most cases, it is used to change from the multi-user state (state 2) to another state.
By default, shutdown brings the system to a state where only the console has access to the operating system. This state is called single-user.
Before starting to shut down daemons and killing processes, shutdown sends a warning message and, by default, a final message asking for confirmation. message is a string that is sent out following the standard warning message "The system will be shut down in .\|.\|." If the string contains more than one word, it should be contained within single (') or double (") quotation marks.
The warning message and the user provided message are output when there are 7200, 3600, 1800, 1200, 600, 300, 120, 60, and 30 seconds remaining before shutdown begins. See EXAMPLES.
System state definitions are: state 0
Stop the operating system.
State 1 is referred to as the administrative state. In state 1 file systems required for multi-user operations are mounted, and logins requiring access to multi-user file systems can be used. When the system comes up from firmware mode into state 1, only the console is active and other multi-user (state 2) services are unavailable. Note that not all user processes are stopped when transitioning from multi-user state to state 1.
State s (or S) is referred to as the single-user state. All user processes are stopped on transitions to this state. In the single-user state, file systems required for multi-user logins are unmounted and the system can only be accessed through the console. Logins requiring access to multi-user file systems cannot be used.
Shut the machine down so that it is safe to remove the power. Have the machine remove power, if possible. The rc0 procedure is called to perform this task.
Stop the operating system and reboot to the state defined by the initdefault entry in /etc/inittab. The rc6 procedure is called to perform this task.
Pre-answer the confirmation question so the command can be run without user intervention.
Allow the super user to change the number of seconds from the 60-second default.
If there are warnings, init-state specifies the state init is to be in. By default, system state `s' is used.
Example 1 Using shutdown
In the following example, shutdown is being executed on host foo and is scheduled in 120 seconds. The warning message is output 2 minutes, 1 minute, and 30 seconds before the final confirmation message.
example# shutdown -i S -g 120 "===== disk replacement =====" Shutdown started. Tue Jun 7 14:51:40 PDT 1994 Broadcast Message from root (pts/1) on foo Tue Jun 7 14:51:41.\|.\|. The system will be shut down in 2 minutes ===== disk replacement ===== Broadcast Message from root (pts/1) on foo Tue Jun 7 14:52:41.\|.\|. The system will be shut down in 1 minutes ===== disk replacement ===== Broadcast Message from root (pts/1) on foo Tue Jun 7 14:53:41.\|.\|. The system will be shut down in 30 seconds ===== disk replacement ===== Do you want to continue? (y or n):
controls process dispatching by init
init.d (5), inittab (5), nologin (5), attributes (7), boot (8), halt (8), init (8), killall (8), reboot (8), ufsdump (8)
When a system transitions down to the S or s state, the /etc/nologin file (see nologin(5)) is created. Upon subsequent transition to state 2 (multi-user state), this file is removed by a script in the /etc/rc2.d directory.