1.\" Copyright (c) 1983, 1991, 1993 2.\" The Regents of the University of California. All rights reserved. 3.\" 4.\" Redistribution and use in source and binary forms, with or without 5.\" modification, are permitted provided that the following conditions 6.\" are met: 7.\" 1. Redistributions of source code must retain the above copyright 8.\" notice, this list of conditions and the following disclaimer. 9.\" 2. Redistributions in binary form must reproduce the above copyright 10.\" notice, this list of conditions and the following disclaimer in the 11.\" documentation and/or other materials provided with the distribution. 12.\" 4. Neither the name of the University nor the names of its contributors 13.\" may be used to endorse or promote products derived from this software 14.\" without specific prior written permission. 15.\" 16.\" THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND 17.\" ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 18.\" IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 19.\" ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE 20.\" FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 21.\" DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 22.\" OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 23.\" HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT 24.\" LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 25.\" OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 26.\" SUCH DAMAGE. 27.\" 28.\" @(#)rmt.8 8.3 (Berkeley) 6/1/94 29.\" $FreeBSD$ 30.\" 31.Dd June 1, 1994 32.Dt RMT 8 33.Os 34.Sh NAME 35.Nm rmt 36.Nd remote magtape protocol module 37.Sh SYNOPSIS 38.Nm 39.Sh DESCRIPTION 40The 41.Nm 42utility is used by the remote dump and restore programs 43in manipulating a magnetic tape drive through an interprocess 44communication connection. 45It is normally started up with an 46.Xr rcmd 3 47call. 48.Pp 49The 50.Nm 51utility accepts requests specific to the manipulation of 52magnetic tapes, performs the commands, then responds with 53a status indication. 54All responses are in 55.Tn ASCII 56and in 57one of two forms. 58Successful commands have responses of: 59.Bd -ragged -offset indent 60.Sm off 61.Sy A Ar number No \en 62.Sm on 63.Ed 64.Pp 65.Ar Number 66is an 67.Tn ASCII 68representation of a decimal number. 69Unsuccessful commands are responded to with: 70.Bd -ragged -offset indent 71.Sm off 72.Xo Sy E Ar error-number 73.No \en Ar error-message 74.No \en 75.Xc 76.Sm on 77.Ed 78.Pp 79.Ar Error-number 80is one of the possible error 81numbers described in 82.Xr intro 2 83and 84.Ar error-message 85is the corresponding error string as printed 86from a call to 87.Xr perror 3 . 88The protocol is comprised of the 89following commands, which are sent as indicated - no spaces are supplied 90between the command and its arguments, or between its arguments, and 91.Ql \en 92indicates that a newline should be supplied: 93.Bl -tag -width Ds 94.Sm off 95.It Xo Sy \&O Ar device 96.No \en Ar mode No \en 97.Xc 98.Sm on 99Open the specified 100.Ar device 101using the indicated 102.Ar mode . 103.Ar Device 104is a full pathname and 105.Ar mode 106is an 107.Tn ASCII 108representation of a decimal 109number suitable for passing to 110.Xr open 2 . 111If a device had already been opened, it is 112closed before a new open is performed. 113.Sm off 114.It Xo Sy C Ar device No \en 115.Xc 116.Sm on 117Close the currently open device. 118The 119.Ar device 120specified is ignored. 121.Sm off 122.It Xo Sy L 123.Ar whence No \en 124.Ar offset No \en 125.Xc 126.Sm on 127Perform an 128.Xr lseek 2 129operation using the specified parameters. 130The response value is that returned from the 131.Xr lseek 2 132call. 133.Sm off 134.It Sy W Ar count No \en 135.Sm on 136Write data onto the open device. 137The 138.Nm 139utility reads 140.Ar count 141bytes from the connection, aborting if 142a premature end-of-file is encountered. 143The response value is that returned from 144the 145.Xr write 2 146call. 147.Sm off 148.It Sy R Ar count No \en 149.Sm on 150Read 151.Ar count 152bytes of data from the open device. 153If 154.Ar count 155exceeds the size of the data buffer (10 kilobytes), it is 156truncated to the data buffer size. 157The 158.Nm 159utility then performs the requested 160.Xr read 2 161and responds with 162.Sm off 163.Sy A Ar count-read No \en 164.Sm on 165if the read was 166successful; otherwise an error in the 167standard format is returned. 168If the read 169was successful, the data read is then sent. 170.Sm off 171.It Xo Sy I Ar operation 172.No \en Ar count No \en 173.Xc 174.Sm on 175Perform a 176.Dv MTIOCOP 177.Xr ioctl 2 178command using the specified parameters. 179The parameters are interpreted as the 180.Tn ASCII 181representations of the decimal values 182to place in the 183.Ar mt_op 184and 185.Ar mt_count 186fields of the structure used in the 187.Xr ioctl 2 188call. 189The return value is the 190.Ar count 191parameter when the operation is successful. 192.It Sy S 193Return the status of the open device, as 194obtained with a 195.Dv MTIOCGET 196.Xr ioctl 2 197call. 198If the operation was successful, 199an ``ack'' is sent with the size of the 200status buffer, then the status buffer is 201sent (in binary). 202.El 203.Pp 204Any other command causes 205.Nm 206to exit. 207.Sh DIAGNOSTICS 208All responses are of the form described above. 209.Sh SEE ALSO 210.Xr rcmd 3 , 211.Xr mtio 4 , 212.Xr rdump 8 , 213.Xr rrestore 8 214.Sh HISTORY 215The 216.Nm 217utility appeared in 218.Bx 4.2 . 219.Sh BUGS 220People should be discouraged from using this for a remote 221file access protocol. 222