1# 2# LINT -- config file for checking all the sources, tries to pull in 3# as much of the source tree as it can. 4# 5# $Id: LINT,v 1.532 1999/01/11 03:18:31 yokota Exp $ 6# 7# NB: You probably don't want to try running a kernel built from this 8# file. Instead, you should start from GENERIC, and add options from 9# this file as required. 10# 11 12# 13# This directive is mandatory; it defines the architecture to be 14# configured for; in this case, the 386 family based IBM-PC and 15# compatibles. 16# 17machine "i386" 18 19# 20# This is the ``identification'' of the kernel. Usually this should 21# be the same as the name of your kernel. 22# 23ident LINT 24 25# 26# The `maxusers' parameter controls the static sizing of a number of 27# internal system tables by a complicated formula defined in param.c. 28# 29maxusers 10 30 31# 32# Certain applications can grow to be larger than the 128M limit 33# that FreeBSD initially imposes. Below are some options to 34# allow that limit to grow to 256MB, and can be increased further 35# with changing the parameters. MAXDSIZ is the maximum that the 36# limit can be set to, and the DFLDSIZ is the default value for 37# the limit. You might want to set the default lower than the 38# max, and explicitly set the maximum with a shell command for processes 39# that regularly exceed the limit like INND. 40# 41options "MAXDSIZ=(256*1024*1024)" 42options "DFLDSIZ=(256*1024*1024)" 43 44# When this is set, be extra conservative in various parts of the kernel 45# and choose functionality over speed (on the widest variety of systems). 46options FAILSAFE 47 48# Options for the VM subsystem 49#options PQ_NOOPT # No coloring 50options PQ_LARGECACHE # color for 512k/16k cache 51#options PQ_HUGECACHE # color for 1024k/16k cache 52 53# This allows you to actually store this configuration file into 54# the kernel binary itself, where it may be later read by saying: 55# strings -aout -n 3 /kernel | grep ^___ | sed -e 's/^___//' > MYKERNEL 56# 57options INCLUDE_CONFIG_FILE # Include this file in kernel 58 59# 60# This directive defines a number of things: 61# - The compiled kernel is to be called `kernel' 62# - The root filesystem might be on partition wd0a 63# - Crash dumps will be written to wd0b, if possible. Specifying the 64# dump device here is not recommended. Use dumpon(8). 65# 66config kernel root on wd0 dumps on wd0 67 68 69##################################################################### 70# SMP OPTIONS: 71# 72# SMP enables building of a Symmetric MultiProcessor Kernel. 73# APIC_IO enables the use of the IO APIC for Symmetric I/O. 74# NCPU sets the number of CPUs, defaults to 2. 75# NBUS sets the number of busses, defaults to 4. 76# NAPIC sets the number of IO APICs on the motherboard, defaults to 1. 77# NINTR sets the total number of INTs provided by the motherboard. 78# 79# Notes: 80# 81# An SMP kernel will ONLY run on an Intel MP spec. qualified motherboard. 82# 83# Be sure to disable 'cpu "I386_CPU"' && 'cpu "I486_CPU"' for SMP kernels. 84# 85# Check the 'Rogue SMP hardware' section to see if additional options 86# are required by your hardware. 87# 88 89# Mandatory: 90options SMP # Symmetric MultiProcessor Kernel 91options APIC_IO # Symmetric (APIC) I/O 92 93# Optional, these are the defaults plus 1: 94options NCPU=5 # number of CPUs 95options NBUS=5 # number of busses 96options NAPIC=2 # number of IO APICs 97options NINTR=25 # number of INTs 98 99# 100# Rogue SMP hardware: 101# 102 103# Bridged PCI cards: 104# 105# The MP tables of most of the current generation MP motherboards 106# do NOT properly support bridged PCI cards. To use one of these 107# cards you should refer to ??? 108 109 110##################################################################### 111# CPU OPTIONS 112 113# 114# You must specify at least one CPU (the one you intend to run on); 115# deleting the specification for CPUs you don't need to use may make 116# parts of the system run faster. This is especially true removing 117# I386_CPU. 118# 119cpu "I386_CPU" 120cpu "I486_CPU" 121cpu "I586_CPU" # aka Pentium(tm) 122cpu "I686_CPU" # aka Pentium Pro(tm) 123 124# 125# Options for CPU features. 126# 127# CPU_BLUELIGHTNING_FPU_OP_CACHE enables FPU operand cache on IBM 128# BlueLightning CPU. It works only with Cyrix FPU, and this option 129# should not be used with Intel FPU. 130# 131# CPU_BLUELIGHTNING_3X enables triple-clock mode on IBM Blue Lightning 132# CPU if CPU supports it. The default is double-clock mode on 133# BlueLightning CPU box. 134# 135# CPU_BTB_EN enables branch target buffer on Cyrix 5x86 (NOTE 1). 136# 137# CPU_DIRECT_MAPPED_CACHE sets L1 cache of Cyrix 486DLC CPU in direct 138# mapped mode. Default is 2-way set associative mode. 139# 140# CPU_CYRIX_NO_LOCK enables weak locking for the entire address space 141# of Cyrix 6x86 and 6x86MX CPUs. If this option is not set and 142# FAILESAFE is defined, NO_LOCK bit of CCR1 is cleared. (NOTE 3) 143# 144# CPU_DISABLE_5X86_LSSER disables load store serialize (i.e. enables 145# reorder). This option should not be used if you use memory mapped 146# I/O device(s). 147# 148# CPU_FASTER_5X86_FPU enables faster FPU exception handler. 149# 150# CPU_I486_ON_386 enables CPU cache on i486 based CPU upgrade products 151# for i386 machines. 152# 153# CPU_IORT defines I/O clock delay time (NOTE 1). Default vaules of 154# I/O clock delay time on Cyrix 5x86 and 6x86 are 0 and 7,respectively 155# (no clock delay). 156# 157# CPU_LOOP_EN prevents flushing the prefetch buffer if the destination 158# of a jump is already present in the prefetch buffer on Cyrix 5x86(NOTE 159# 1). 160# 161# CPU_RSTK_EN enables return stack on Cyrix 5x86 (NOTE 1). 162# 163# CPU_SUSP_HLT enables suspend on HALT. If this option is set, CPU 164# enters suspend mode following execution of HALT instruction. 165# 166# CPU_WT_ALLOC enables write allocation on Cyrix 6x86/6x86MX and AMD 167# K5/K6/K6-2 cpus. 168# 169# CYRIX_CACHE_WORKS enables CPU cache on Cyrix 486 CPUs with cache 170# flush at hold state. 171# 172# CYRIX_CACHE_REALLY_WORKS enables (1) CPU cache on Cyrix 486 CPUs 173# without cache flush at hold state, and (2) write-back CPU cache on 174# Cyrix 6x86 whose revision < 2.7 (NOTE 2). 175# 176# NO_F00F_HACK disables the hack that prevents Pentiums (and ONLY 177# Pentiums) from locking up when a LOCK CMPXCHG8B instruction is 178# executed. This should be included for ALL kernels that won't run 179# on a Pentium. 180# 181# NO_MEMORY_HOLE is an optimisation for systems with AMD K6 processors 182# which indicates that the 15-16MB range is *definitely* not being 183# occupied by an ISA memory hole. 184# 185# NOTE 1: The options, CPU_BTB_EN, CPU_LOOP_EN, CPU_IORT, 186# CPU_LOOP_ENand CPU_RSTK_EN should not be used becasue of CPU bugs. 187# These options may crash your system. 188# 189# NOTE 2: If CYRIX_CACHE_REALLY_WORKS is not set, CPU cache is enabled 190# in write-through mode when revision < 2.7. If revision of Cyrix 191# 6x86 >= 2.7, CPU cache is always enabled in write-back mode. 192# 193# NOTE 3: This option may cause failures for software that requires 194# locked cycles in order to operate correctly. 195# 196options "CPU_BLUELIGHTNING_FPU_OP_CACHE" 197options "CPU_BLUELIGHTNING_3X" 198options "CPU_BTB_EN" 199options "CPU_DIRECT_MAPPED_CACHE" 200options "CPU_DISABLE_5X86_LSSER" 201options "CPU_FASTER_5X86_FPU" 202options "CPU_I486_ON_386" 203options "CPU_IORT" 204options "CPU_LOOP_EN" 205options "CPU_RSTK_EN" 206options "CPU_SUSP_HLT" 207options "CPU_WT_ALLOC" 208options "CYRIX_CACHE_WORKS" 209options "CYRIX_CACHE_REALLY_WORKS" 210#options "NO_F00F_HACK" 211 212# 213# A math emulator is mandatory if you wish to run on hardware which 214# does not have a floating-point processor. Pick either the original, 215# bogus (but freely-distributable) math emulator, or a much more 216# fully-featured but GPL-licensed emulator taken from Linux. 217# 218options MATH_EMULATE #Support for x87 emulation 219# Don't enable both of these in a real config. 220options GPL_MATH_EMULATE #Support for x87 emulation via 221 #new math emulator 222 223 224##################################################################### 225# COMPATIBILITY OPTIONS 226 227# 228# Implement system calls compatible with 4.3BSD and older versions of 229# FreeBSD. You probably do NOT want to remove this as much current code 230# still relies on the 4.3 emulation. 231# 232options "COMPAT_43" 233 234# 235# Allow user-mode programs to manipulate their local descriptor tables. 236# This option is required for the WINE Windows(tm) emulator, and is 237# not used by anything else (that we know of). 238# 239options USER_LDT #allow user-level control of i386 ldt 240 241# 242# These three options provide support for System V Interface 243# Definition-style interprocess communication, in the form of shared 244# memory, semaphores, and message queues, respectively. 245# 246options SYSVSHM 247options SYSVSEM 248options SYSVMSG 249 250# 251# This option includes a MD5 routine in the kernel, this is used for 252# various authentication and privacy uses. 253# 254options "MD5" 255 256# 257# Allow processes to switch to vm86 mode, as well as enabling direct 258# user-mode access to the I/O port space. This option is necessary for 259# the doscmd emulator to run. 260# 261options "VM86" 262 263 264##################################################################### 265# DEBUGGING OPTIONS 266 267# 268# Enable the kernel debugger. 269# 270options DDB 271 272# 273# Don't drop into DDB for a panic. Intended for unattended operation 274# where you may want to drop to DDB from the console, but still want 275# the machine to recover from a panic 276# 277options DDB_UNATTENDED 278 279# 280# If using GDB remote mode to debug the kernel, there's a non-standard 281# extension to the remote protocol that can be used to use the serial 282# port as both the debugging port and the system console. It's non- 283# standard and you're on your own if you enable it. See also the 284# "remotechat" variables in the FreeBSD specific version of gdb. 285# 286options GDB_REMOTE_CHAT 287 288# 289# KTRACE enables the system-call tracing facility ktrace(2). 290# 291options KTRACE #kernel tracing 292 293# 294# The INVARIANTS option is used in a number of source files to enable 295# extra sanity checking of internal structures. This support is not 296# enabled by default because of the extra time it would take to check 297# for these conditions, which can only occur as a result of 298# programming errors. 299# 300options INVARIANTS 301 302# 303# The INVARIANT_SUPPORT option makes us compile in support for 304# verifying some of the internal structures. It is a prerequisite for 305# 'INVARIANTS', as enabling 'INVARIANTS' will make these functions be 306# called. The intent is that you can set 'INVARIANTS' for single 307# source files (by changing the source file or specifying it on the 308# command line) if you have 'INVARIANT_SUPPORT' enabled. 309# 310options INVARIANT_SUPPORT 311 312# 313# The DIAGNOSTIC option is used to enable extra debugging information 314# from some parts of the kernel. As this makes everything more noisy, 315# it is disabled by default. 316# 317options DIAGNOSTIC 318 319# 320# PERFMON causes the driver for Pentium/Pentium Pro performance counters 321# to be compiled. See perfmon(4) for more information. 322# 323options PERFMON 324 325 326# 327# This option let some drivers co-exist that can't co-exist in a running 328# system. This is used to be able to compile all kernel code in one go for 329# quality assurance purposes (like this file, which the option takes it name 330# from.) 331# 332options COMPILING_LINT 333 334 335# XXX - this doesn't belong here. 336# Allow ordinary users to take the console - this is useful for X. 337options UCONSOLE 338 339# XXX - this doesn't belong here either 340options USERCONFIG #boot -c editor 341options INTRO_USERCONFIG #imply -c and show intro screen 342options VISUAL_USERCONFIG #visual boot -c editor 343 344##################################################################### 345# NETWORKING OPTIONS 346 347# 348# Protocol families: 349# Only the INET (Internet) family is officially supported in FreeBSD. 350# Source code for the NS (Xerox Network Service) is provided for amusement 351# value. 352# 353options INET #Internet communications protocols 354 355options IPX #IPX/SPX communications protocols 356options IPXIP #IPX in IP encapsulation (not available) 357options IPTUNNEL #IP in IPX encapsulation (not available) 358 359options NETATALK #Appletalk communications protocols 360 361# These are currently broken but are shipped due to interest. 362#options NS #Xerox NS protocols 363 364# These are currently broken and are no longer shipped due to lack 365# of interest. 366#options CCITT #X.25 network layer 367#options ISO 368#options TPIP #ISO TP class 4 over IP 369#options TPCONS #ISO TP class 0 over X.25 370#options LLC #X.25 link layer for Ethernets 371#options HDLC #X.25 link layer for serial lines 372#options EON #ISO CLNP over IP 373#options NSIP #XNS over IP 374 375# 376# Network interfaces: 377# The `loop' pseudo-device is MANDATORY when networking is enabled. 378# The `ether' pseudo-device provides generic code to handle 379# Ethernets; it is MANDATORY when a Ethernet device driver is 380# configured. 381# The 'fddi' pseudo-device provides generic code to support FDDI. 382# The `sppp' pseudo-device serves a similar role for certain types 383# of synchronous PPP links (like `cx', `ar'). 384# The `sl' pseudo-device implements the Serial Line IP (SLIP) service. 385# The `ppp' pseudo-device implements the Point-to-Point Protocol. 386# The `bpfilter' pseudo-device enables the Berkeley Packet Filter. Be 387# aware of the legal and administrative consequences of enabling this 388# option. The number of devices determines the maximum number of 389# simultaneous BPF clients programs runnable. 390# The `disc' pseudo-device implements a minimal network interface, 391# which throws away all packets sent and never receives any. It is 392# included for testing purposes. 393# The `tun' pseudo-device implements the User Process PPP (iijppp) 394# 395# The PPP_BSDCOMP option enables support for compress(1) style entire 396# packet compression, the PPP_DEFLATE is for zlib/gzip style compression. 397# PPP_FILTER enables code for filtering the ppp data stream and selecting 398# events for resetting the demand dial activity timer - requires bpfilter. 399# See pppd(8) for more details. 400# 401pseudo-device ether #Generic Ethernet 402pseudo-device fddi #Generic FDDI 403pseudo-device sppp #Generic Synchronous PPP 404pseudo-device loop #Network loopback device 405pseudo-device bpfilter 4 #Berkeley packet filter 406pseudo-device disc #Discard device 407pseudo-device tun 1 #Tunnel driver (user process ppp(8)) 408pseudo-device sl 2 #Serial Line IP 409pseudo-device ppp 2 #Point-to-point protocol 410options PPP_BSDCOMP #PPP BSD-compress support 411options PPP_DEFLATE #PPP zlib/deflate/gzip support 412options PPP_FILTER #enable bpf filtering (needs bpfilter) 413 414# 415# Internet family options: 416# 417# TCP_COMPAT_42 causes the TCP code to emulate certain bugs present in 418# 4.2BSD. This option should not be used unless you have a 4.2BSD 419# machine and TCP connections fail. 420# 421# MROUTING enables the kernel multicast packet forwarder, which works 422# with mrouted(8). 423# 424# IPFIREWALL enables support for IP firewall construction, in 425# conjunction with the `ipfw' program. IPFIREWALL_VERBOSE sends 426# logged packets to the system logger. IPFIREWALL_VERBOSE_LIMIT 427# limits the number of times a matching entry can be logged. 428# 429# WARNING: IPFIREWALL defaults to a policy of "deny ip from any to any" 430# and if you do not add other rules during startup to allow access, 431# YOU WILL LOCK YOURSELF OUT. It is suggested that you set firewall=open 432# in /etc/rc.conf when first enabling this feature, then refining the 433# firewall rules in /etc/rc.firewall after you've tested that the new kernel 434# feature works properly. 435# 436# IPFIREWALL_DEFAULT_TO_ACCEPT causes the default rule (at boot) to 437# allow everything. Use with care, if a cracker can crash your 438# firewall machine, they can get to your protected machines. However, 439# if you are using it as an as-needed filter for specific problems as 440# they arise, then this may be for you. Changing the default to 'allow' 441# means that you won't get stuck if the kernel and /sbin/ipfw binary get 442# out of sync. 443# 444# IPDIVERT enables the divert IP sockets, used by ``ipfw divert'' 445# 446# IPFILTER enables Darren Reed's ipfilter package. 447# IPFILTER_LOG enables ipfilter's logging. 448# IPFILTER_LKM enables LKM support for an ipfilter module (untested). 449# 450# TCPDEBUG is undocumented. 451# 452options "TCP_COMPAT_42" #emulate 4.2BSD TCP bugs 453options MROUTING # Multicast routing 454options IPFIREWALL #firewall 455options IPFIREWALL_VERBOSE #print information about 456 # dropped packets 457options IPFIREWALL_FORWARD #enable xparent proxy support 458options "IPFIREWALL_VERBOSE_LIMIT=100" #limit verbosity 459options IPFIREWALL_DEFAULT_TO_ACCEPT #allow everything by default 460options IPDIVERT #divert sockets 461options IPFILTER #kernel ipfilter support 462options IPFILTER_LOG #ipfilter logging 463#options IPFILTER_LKM #kernel support for ip_fil.o LKM 464options TCPDEBUG 465 466# ICMP_BANDLIM enables icmp error response bandwidth limiting. You 467# typically want this option as it will help protect the machine from 468# D.O.S. packet attacks. 469# 470options "ICMP_BANDLIM" 471 472# DUMMYNET enables the "dummynet" bandwidth limiter. You need 473# IPFIREWALL as well. See the dummynet(4) manpage for more info. 474# BRIDGE enables bridging between ethernet cards -- see bridge(4). 475# You can use IPFIREWALL and dummynet together with bridging. 476options DUMMYNET 477options BRIDGE 478 479# 480# ATM (HARP version) options 481# 482# ATM_CORE includes the base ATM functionality code. This must be included 483# for ATM support. 484# 485# ATM_IP includes support for running IP over ATM. 486# 487# At least one (and usually only one) of the following signalling managers 488# must be included (note that all signalling managers include PVC support): 489# ATM_SIGPVC includes support for the PVC-only signalling manager `sigpvc'. 490# ATM_SPANS includes support for the `spans' signalling manager, which runs 491# the FORE Systems's proprietary SPANS signalling protocol. 492# ATM_UNI includes support for the `uni30' and `uni31' signalling managers, 493# which run the ATM Forum UNI 3.x signalling protocols. 494# 495# The `hea' driver provides support for the Efficient Networks, Inc. 496# ENI-155p ATM PCI Adapter. 497# 498# The `hfa' driver provides support for the FORE Systems, Inc. 499# PCA-200E ATM PCI Adapter. 500# 501options ATM_CORE #core ATM protocol family 502options ATM_IP #IP over ATM support 503options ATM_SIGPVC #SIGPVC signalling manager 504options ATM_SPANS #SPANS signalling manager 505options ATM_UNI #UNI signalling manager 506device hea0 #Efficient ENI-155p ATM PCI 507device hfa0 #FORE PCA-200E ATM PCI 508 509 510##################################################################### 511# FILESYSTEM OPTIONS 512 513# 514# Only the root, /usr, and /tmp filesystems need be statically 515# compiled; everything else will be automatically loaded at mount 516# time. (Exception: the UFS family---FFS, and MFS --- cannot 517# currently be demand-loaded.) Some people still prefer to statically 518# compile other filesystems as well. 519# 520# NB: The NULL, PORTAL, UMAP and UNION filesystems are known to be 521# buggy, and WILL panic your system if you attempt to do anything with 522# them. They are included here as an incentive for some enterprising 523# soul to sit down and fix them. 524# 525 526# One of these is mandatory: 527options FFS #Fast filesystem 528options MFS #Memory File System 529options NFS #Network File System 530 531# The rest are optional: 532# options NFS_NOSERVER #Disable the NFS-server code. 533options "CD9660" #ISO 9660 filesystem 534options FDESC #File descriptor filesystem 535options KERNFS #Kernel filesystem 536options MSDOSFS #MS DOS File System 537options NULLFS #NULL filesystem 538options PORTAL #Portal filesystem 539options PROCFS #Process filesystem 540options UMAPFS #UID map filesystem 541options UNION #Union filesystem 542# The xFS_ROOT options REQUIRE the associated ``options xFS'' 543options "CD9660_ROOT" #CD-ROM usable as root device 544options FFS_ROOT #FFS usable as root device 545options MFS_ROOT #MFS usable as root device 546options NFS_ROOT #NFS usable as root device 547# This code is still experimental (e.g. doesn't handle disk slices well). 548# Also, 'options MFS' is currently incompatible with DEVFS. 549options DEVFS #devices filesystem 550 551# Soft updates is technique for improving file system speed and 552# making abrupt shutdown less risky. It is not enabled by default due 553# to copyright restraints on the code that implement it. 554# 555# Read .../../ufs/ffs/README.softupdates to learn what you need to 556# do to enable this. ../../../contrib/sys/softupdates/README gives 557# more details on how they actually work. 558# 559#options SOFTUPDATES 560 561# Make space in the kernel for a MFS root filesystem. Define to the number 562# of kilobytes to reserve for the filesystem. 563options MFS_ROOT_SIZE=10 564# Allows MFS filesystems to be exported via nfs 565options EXPORTMFS 566 567# Allow this many swap-devices. 568options NSWAPDEV=20 569 570# Disk quotas are supported when this option is enabled. If you 571# change the value of this option, you must do a `make clean' in your 572# kernel compile directory in order to get a working kernel. 573# 574options QUOTA #enable disk quotas 575 576# Add more checking code to various filesystems 577#options NULLFS_DIAGNOSTIC 578#options KERNFS_DIAGNOSTIC 579#options UMAPFS_DIAGNOSTIC 580#options UNION_DIAGNOSTIC 581 582# In particular multi-session CD-Rs might require a huge amount of 583# time in order to "settle". If we are about mounting them as the 584# root f/s, we gotta wait a little. 585# 586# The number is supposed to be in seconds. 587options "CD9660_ROOTDELAY=20" 588 589# If you are running a machine just as a fileserver for PC and MAC 590# users, using SAMBA or Netatalk, you may consider setting this option 591# and keeping all those users' directories on a filesystem that is 592# mounted with the suiddir option. This gives new files the same 593# ownership as the directory (similiar to group). It's a security hole 594# if you let these users run programs, so confine it to file-servers 595# (but it'll save you lots of headaches in those cases). Root owned 596# directories are exempt and X bits are cleared. The suid bit must be 597# set on the directory as well; see chmod(1) PC owners can't see/set 598# ownerships so they keep getting their toes trodden on. This saves 599# you all the support calls as the filesystem it's used on will act as 600# they expect: "It's my dir so it must be my file". 601# 602options SUIDDIR 603 604 605# Add some error checking code to the null_bypass routine 606# in the NULL filesystem 607#options SAFETY 608 609 610# NFS options: 611options "NFS_MINATTRTIMO=3" # VREG attrib cache timeout in sec 612options "NFS_MAXATTRTIMO=60" 613options "NFS_MINDIRATTRTIMO=30" # VDIR attrib cache timeout in sec 614options "NFS_MAXDIRATTRTIMO=60" 615options "NFS_GATHERDELAY=10" # Default write gather delay (msec) 616options "NFS_UIDHASHSIZ=29" # Tune the size of nfssvc_sock with this 617options "NFS_WDELAYHASHSIZ=16" # and with this 618options "NFS_MUIDHASHSIZ=63" # Tune the size of nfsmount with this 619options NFS_DEBUG # Enable NFS Debugging 620 621# Coda stuff: 622options CODA #CODA filesystem. 623pseudo-device vcoda 4 #coda minicache <-> venus comm. 624 625 626##################################################################### 627# POSIX P1003.1B 628 629# Real time extensions added int the 1993 Posix 630# P1003_1B: Infrastructure 631# _KPOSIX_PRIORITY_SCHEDULING: Build in _POSIX_PRIORITY_SCHEDULING 632# _KPOSIX_VERSION: Version kernel is built for 633 634options "P1003_1B" 635options "_KPOSIX_PRIORITY_SCHEDULING" 636options "_KPOSIX_VERSION=199309L" 637 638 639##################################################################### 640# SCSI DEVICES 641 642# SCSI DEVICE CONFIGURATION 643 644# The SCSI subsystem consists of the `base' SCSI code, a number of 645# high-level SCSI device `type' drivers, and the low-level host-adapter 646# device drivers. The host adapters are listed in the ISA and PCI 647# device configuration sections below. 648# 649# Beginning with FreeBSD 2.0.5 you can wire down your SCSI devices so 650# that a given bus, target, and LUN always come on line as the same 651# device unit. In earlier versions the unit numbers were assigned 652# in the order that the devices were probed on the SCSI bus. This 653# means that if you removed a disk drive, you may have had to rewrite 654# your /etc/fstab file, and also that you had to be careful when adding 655# a new disk as it may have been probed earlier and moved your device 656# configuration around. 657 658# This old behavior is maintained as the default behavior. The unit 659# assignment begins with the first non-wired down unit for a device 660# type. For example, if you wire a disk as "da3" then the first 661# non-wired disk will be assigned da4. 662 663# The syntax for wiring down devices is: 664 665# controller scbus0 at ahc0 # Single bus device 666# controller scbus1 at ahc1 bus 0 # Single bus device 667# controller scbus3 at ahc2 bus 0 # Twin bus device 668# controller scbus2 at ahc2 bus 1 # Twin bus device 669# disk da0 at scbus0 target 0 unit 0 670# disk da1 at scbus3 target 1 671# disk da2 at scbus2 target 3 672# tape st1 at scbus1 target 6 673# device cd0 at scbus? 674 675# "units" (SCSI logical unit number) that are not specified are 676# treated as if specified as LUN 0. 677 678# All SCSI devices allocate as many units as are required. 679 680# The "unknown" device (uk? in pre-2.0.5) is now part of the base SCSI 681# configuration and doesn't have to be explicitly configured. 682 683controller scbus0 #base SCSI code 684device ch0 #SCSI media changers 685device da0 #SCSI direct access devices (aka disks) 686device sa0 #SCSI tapes 687device cd0 #SCSI CD-ROMs 688#device od0 #SCSI optical disk 689device pass0 #CAM passthrough driver 690 691# The previous devices (ch, da, st, cd) are recognized by config. 692# config doesn't (and shouldn't) know about these newer ones, 693# so we have to specify that they are on a SCSI bus with the "at scbus?" 694# clause. 695 696device pt0 at scbus? # SCSI processor type 697device sctarg0 at scbus? # SCSI target 698 699# CAM OPTIONS: 700# debugging options: 701# -- NOTE -- If you specify one of the bus/target/lun options, you must 702# specify them all! 703# CAMDEBUG: When defined enables debugging macros 704# CAM_DEBUG_BUS: Debug the given bus. Use -1 to debug all busses. 705# CAM_DEBUG_TARGET: Debug the given target. Use -1 to debug all targets. 706# CAM_DEBUG_LUN: Debug the given lun. Use -1 to debug all luns. 707# CAM_DEBUG_FLAGS: OR together CAM_DEBUG_INFO, CAM_DEBUG_TRACE, 708# CAM_DEBUG_SUBTRACE, and CAM_DEBUG_CDB 709# 710# CAM_MAX_HIGHPOWER: Maximum number of concurrent high power (start unit) cmds 711# SCSI_NO_SENSE_STRINGS: When defined disables sense descriptions 712# SCSI_NO_OP_STRINGS: When defined disables opcode descriptions 713# SCSI_REPORT_GEOMETRY: Always report disk geometry at boot up instead 714# of only when booting verbosely. 715# SCSI_DELAY: The number of MILLISECONDS to freeze the SIM (scsi adapter) 716# queue after a bus reset, and the number of milliseconds to 717# freeze the device queue after a bus device reset. 718options CAMDEBUG 719options "CAM_DEBUG_BUS=-1" 720options "CAM_DEBUG_TARGET=-1" 721options "CAM_DEBUG_LUN=-1" 722options "CAM_DEBUG_FLAGS=CAM_DEBUG_INFO|CAM_DEBUG_TRACE|CAM_DEBUG_CDB" 723options "CAM_MAX_HIGHPOWER=4" 724options SCSI_NO_SENSE_STRINGS 725options SCSI_NO_OP_STRINGS 726options SCSI_REPORT_GEOMETRY 727options SCSI_DELAY=8000 # Be pessimistic about Joe SCSI device 728 729# Options for the CAM CDROM driver: 730# CHANGER_MIN_BUSY_SECONDS: Guaranteed minimum time quantum for a changer LUN 731# CHANGER_MAX_BUSY_SECONDS: Maximum time quantum per changer LUN, only 732# enforced if there is I/O waiting for another LUN 733# The compiled in defaults for these variables are 2 and 10 seconds, 734# respectively. 735# 736# These can also be changed on the fly with the following sysctl variables: 737# kern.cam.cd.changer.min_busy_seconds 738# kern.cam.cd.changer.max_busy_seconds 739# 740options "CHANGER_MIN_BUSY_SECONDS=2" 741options "CHANGER_MAX_BUSY_SECONDS=10" 742 743# Options for the CAM sequential access driver: 744# SA_SPACE_TIMEOUT: Timeout for space operations, in minutes 745# SA_REWIND_TIMEOUT: Timeout for rewind operations, in minutes 746# SA_ERASE_TIMEOUT: Timeout for erase operations, in minutes 747options "SA_SPACE_TIMEOUT=(60)" 748options "SA_REWIND_TIMEOUT=(2*60)" 749options "SA_ERASE_TIMEOUT=(4*60)" 750 751 752##################################################################### 753# MISCELLANEOUS DEVICES AND OPTIONS 754 755# The `pty' device usually turns out to be ``effectively mandatory'', 756# as it is required for `telnetd', `rlogind', `screen', `emacs', and 757# `xterm', among others. 758 759pseudo-device pty 16 #Pseudo ttys - can go as high as 256 760pseudo-device speaker #Play IBM BASIC-style noises out your speaker 761pseudo-device gzip #Exec gzipped a.out's 762pseudo-device vn #Vnode driver (turns a file into a device) 763pseudo-device snp 3 #Snoop device - to look at pty/vty/etc.. 764pseudo-device ccd 4 #Concatenated disk driver 765pseudo-device vinum #Vinum concat/mirror/raid driver 766options VINUMDEBUG #enable Vinum debugging hooks 767 768# These are only for watching for bitrot in old tty code. 769# broken 770#pseudo-device tb 771 772# Size of the kernel message buffer. Should be N * pagesize. 773options "MSGBUF_SIZE=40960" 774 775 776##################################################################### 777# HARDWARE DEVICE CONFIGURATION 778 779# ISA and EISA devices: 780# EISA support is available for some device, so they can be auto-probed. 781# Micro Channel is not supported at all. 782 783# 784# Mandatory ISA devices: isa, npx 785# 786controller isa0 787 788# 789# Options for `isa': 790# 791# AUTO_EOI_1 enables the `automatic EOI' feature for the master 8259A 792# interrupt controller. This saves about 0.7-1.25 usec for each interrupt. 793# This option breaks suspend/resume on some portables. 794# 795# AUTO_EOI_2 enables the `automatic EOI' feature for the slave 8259A 796# interrupt controller. This saves about 0.7-1.25 usec for each interrupt. 797# Automatic EOI is documented not to work for for the slave with the 798# original i8259A, but it works for some clones and some integrated 799# versions. 800# 801# MAXMEM specifies the amount of RAM on the machine; if this is not 802# specified, FreeBSD will first read the amount of memory from the CMOS 803# RAM, so the amount of memory will initially be limited to 64MB or 16MB 804# depending on the BIOS. If the BIOS reports 64MB, a memory probe will 805# then attempt to detect the installed amount of RAM. If this probe 806# fails to detect >64MB RAM you will have to use the MAXMEM option. 807# The amount is in kilobytes, so for a machine with 128MB of RAM, it would 808# be 131072 (128 * 1024). 809# 810# TUNE_1542 enables the automatic ISA bus speed selection for the 811# Adaptec 1542 boards. Does not work for all boards, use it with caution. 812# 813# BROKEN_KEYBOARD_RESET disables the use of the keyboard controller to 814# reset the CPU for reboot. This is needed on some systems with broken 815# keyboard controllers. 816# 817# PAS_JOYSTICK_ENABLE enables the gameport on the ProAudio Spectrum 818 819options "AUTO_EOI_1" 820#options "AUTO_EOI_2" 821options "MAXMEM=(128*1024)" 822options "TUNE_1542" 823#options BROKEN_KEYBOARD_RESET 824#options PAS_JOYSTICK_ENABLE 825 826# Enable support for the kernel PLL to use an external PPS signal, 827# under supervision of [x]ntpd(8) 828# More info in ftp://ftp.udel.edu/pub/ntp/kernel.tar.Z 829 830options PPS_SYNC 831 832# If you see the "calcru: negative time of %ld usec for pid %d (%s)\n" 833# message you probably have some broken sw/hw which disables interrupts 834# for too long. You can make the system more resistant to this by 835# choosing a high value for NTIMECOUNTER. The default is 5, there 836# is no upper limit but more than a couple of hundred are not productive. 837 838options "NTIMECOUNTER=20" 839 840# Enable PnP support in the kernel. This allows you to automaticly 841# attach to PnP cards for drivers that support it and allows you to 842# configure cards from USERCONFIG. See pnp(4) for more info. 843controller pnp0 844 845# The keyboard controller; it controlls the keyboard and the PS/2 mouse. 846controller atkbdc0 at isa? port IO_KBD tty 847 848# The AT keyboard 849device atkbd0 at isa? tty irq 1 850 851# PS/2 mouse 852device psm0 at isa? tty irq 12 853 854# Options for psm: 855options PSM_HOOKAPM #hook the APM resume event, useful 856 #for some laptops 857options PSM_RESETAFTERSUSPEND #reset the device at the resume event 858 859# The video card driver. 860device vga0 at isa? port ? conflicts 861 862# Splash screen at start up! Screen savers require this too. 863pseudo-device splash 864 865# The pcvt console driver (vt220 compatible). 866device vt0 at isa? tty 867options XSERVER # support for running an X server. 868options FAT_CURSOR # start with block cursor 869# This PCVT option is for keyboards such as those used on IBM ThinkPad laptops 870options PCVT_SCANSET=2 # IBM keyboards are non-std 871 872# The syscons console driver (sco color console compatible). 873device sc0 at isa? tty 874options MAXCONS=16 # number of virtual consoles 875options VGA_SLOW_IOACCESS # do byte-wide i/o's to TS and GDC regs 876options "STD8X16FONT" # Compile font in 877makeoptions "STD8X16FONT"="cp850" 878options SC_HISTORY_SIZE=200 # number of history buffer lines 879options SC_DISABLE_REBOOT # disable reboot key sequence 880# Try the following option if the mouse pointer is not drawn correctly 881# or font does not seem to be loaded properly. May cause flicker on 882# some systems. 883#options SC_ALT_SEQACCESS 884 885# To include support for VESA video modes 886# Dont use together with SMP!! 887options VESA # needs VM86 defined too!! 888 889# 890# `flags' for sc0: 891# 0x01 Use a 'visual' bell 892# 0x02 Use a 'blink' cursor 893# 0x04 Use a 'underline' cursor 894# 0x06 Use a 'blinking underline' (destructive) cursor 895# 0x08 Force detection of keyboard, else we always assume a keyboard 896# 0x10 Old-style (XT) keyboard support, useful for older ThinkPads 897# 0x20 Don't reset keyboard, useful for some newer ThinkPads 898# 0x40 Make the bell quiet if it is rung in the backgroud vty. 899 900# 901# The Numeric Processing eXtension driver. This should be configured if 902# your machine has a math co-processor, unless the coprocessor is very 903# buggy. If it is not configured then you *must* configure math emulation 904# (see above). If both npx0 and emulation are configured, then only npx0 905# is used (provided it works). 906device npx0 at isa? port IO_NPX iosiz 0x0 flags 0x0 irq 13 907 908# 909# `flags' for npx0: 910# 0x01 don't use the npx registers to optimize bcopy 911# 0x02 don't use the npx registers to optimize bzero 912# 0x04 don't use the npx registers to optimize copyin or copyout. 913# The npx registers are normally used to optimize copying and zeroing when 914# all of the following conditions are satisfied: 915# "I586_CPU" is an option 916# the cpu is an i586 (perhaps not a Pentium) 917# the probe for npx0 succeeds 918# INT 16 exception handling works. 919# Then copying and zeroing using the npx registers is normally 30-100% faster. 920# The flags can be used to control cases where it doesn't work or is slower. 921# Setting them at boot time using userconfig works right (the optimizations 922# are not used until later in the bootstrap when npx0 is attached). 923# 924 925# 926# `iosiz' for npx0: 927# This can be used instead of the MAXMEM option to set the memory size. If 928# it is nonzero, then it overrides both the MAXMEM option and the memory 929# size reported by the BIOS. Setting it at boot time using userconfig takes 930# effect on the next reboot after the change has been recorded in the kernel 931# binary (the size is used early in the boot before userconfig has a chance 932# to change it). 933# 934 935# 936# Optional ISA and EISA devices: 937# 938 939# 940# SCSI host adapters: `aha', `aic', `bt' 941# 942# adv: All Narrow SCSI bus AdvanSys controllers. 943# adw: Second Generation AdvanSys controllers including the ADV940UW. 944# aha: Adaptec 154x 945# ahc: Adaptec 274x/284x/294x 946# aic: Adaptec 152x and sound cards using the Adaptec AIC-6360 (slow!) 947# bt: Most Buslogic controllers 948# 949# Note that the order is important in order for Buslogic cards to be 950# probed correctly. 951# 952 953controller bt0 at isa? port "IO_BT0" cam irq ? 954controller adv0 at isa? port ? cam irq ? 955controller adw0 956controller aha0 at isa? port ? cam irq ? 957 958#!CAM# controller aic0 at isa? port 0x340 bio irq 11 959 960 961# 962# ST-506, ESDI, and IDE hard disks: `wdc' and `wd' 963# 964# The flags fields are used to enable the multi-sector I/O and 965# the 32BIT I/O modes. The flags may be used in either the controller 966# definition or in the individual disk definitions. The controller 967# definition is supported for the boot configuration stuff. 968# 969# Each drive has a 16 bit flags value defined: 970# The low 8 bits are the maximum value for the multi-sector I/O, 971# where 0xff defaults to the maximum that the drive can handle. 972# The high bit of the 16 bit flags (0x8000) allows probing for 973# 32 bit transfers. Bit 14 (0x4000) enables a hack to wake 974# up powered-down laptop drives. Bit 13 (0x2000) allows 975# probing for PCI IDE DMA controllers, such as Intel's PIIX 976# south bridges. Bit 12 (0x1000) sets LBA mode instead of the 977# default CHS mode for accessing the drive. See the wd.4 man page. 978# 979# The flags field for the drives can be specified in the controller 980# specification with the low 16 bits for drive 0, and the high 16 bits 981# for drive 1. 982# e.g.: 983#controller wdc0 at isa? port "IO_WD1" bio irq 14 flags 0x00ff8004 984# 985# specifies that drive 0 will be allowed to probe for 32 bit transfers and 986# a maximum multi-sector transfer of 4 sectors, and drive 1 will not be 987# allowed to probe for 32 bit transfers, but will allow multi-sector 988# transfers up to the maximum that the drive supports. 989# 990# If you are using a PCI controller that is not running in compatibility 991# mode (for example, it is a 2nd IDE PCI interface), then use config line(s) 992# such as: 993# 994#controller wdc2 at isa? port "0" bio irq ? flags 0xa0ffa0ff 995#disk wd4 at wdc2 drive 0 996#disk wd5 at wdc2 drive 1 997# 998#controller wdc3 at isa? port "0" bio irq ? flags 0xa0ffa0ff 999#disk wd6 at wdc3 drive 0 1000#disk wd7 at wdc3 drive 1 1001# 1002# Note that the above config would be useful for a Promise card, when used 1003# on a MB that already has a PIIX controller. Note the bogus irq and port 1004# entries. These are automatically filled in by the IDE/PCI support. 1005# 1006 1007controller wdc0 at isa? port "IO_WD1" bio irq 14 1008disk wd0 at wdc0 drive 0 1009disk wd1 at wdc0 drive 1 1010controller wdc1 at isa? port "IO_WD2" bio irq 15 1011disk wd2 at wdc1 drive 0 1012disk wd3 at wdc1 drive 1 1013 1014# 1015# Options for `wdc': 1016# 1017# CMD640 enables serializing access to primary and secondary channel 1018# of the CMD640B IDE Chip. The serializing will only take place 1019# if this option is set *and* the chip is probed by the pci-system. 1020# 1021options "CMD640" #Enable work around for CMD640 h/w bug 1022# 1023# ATAPI enables the support for ATAPI-compatible IDE devices 1024# 1025options ATAPI #Enable ATAPI support for IDE bus 1026options ATAPI_STATIC #Don't do it as an LKM 1027 1028# 1029# This option allow you to override the default probe time for IDE 1030# devices, to get a faster probe. Setting this below 10000 violate 1031# the IDE specs, but may still work for you (it will work for most 1032# people). 1033# 1034options IDE_DELAY=8000 # Be optimistic about Joe IDE device 1035 1036# IDE CD-ROM & CD-R/RW driver - requires wdc controller and ATAPI option 1037device acd0 1038 1039# IDE floppy driver - requires wdc controller and ATAPI option 1040device wfd0 1041 1042# IDE tape driver - requires wdc controller and ATAPI option 1043device wst0 1044 1045 1046# 1047# Standard floppy disk controllers and floppy tapes: `fdc', `fd', and `ft' 1048# 1049controller fdc0 at isa? port "IO_FD1" bio irq 6 drq 2 1050# 1051# FDC_DEBUG enables floppy debugging. Since the debug output is huge, you 1052# gotta turn it actually on by setting the variable fd_debug with DDB, 1053# however. 1054options FDC_DEBUG 1055# FDC_YE enables support for the floppies used on the Libretto. This is a 1056# pcmcia floppy. You will also need to add 1057#card "Y-E DATA" "External FDD" 1058# config 0x4 "fdc0" 10 1059# to your pccard.conf file. 1060options FDC_YE 1061# This option is undocumented on purpose. 1062options FDC_PRINT_BOGUS_CHIPTYPE 1063# 1064# Activate this line instead of the fdc0 line above if you happen to 1065# have an Insight floppy tape. Probing them proved to be dangerous 1066# for people with floppy disks only, so it's "hidden" behind a flag: 1067#controller fdc0 at isa? port "IO_FD1" bio flags 1 irq 6 drq 2 1068 1069disk fd0 at fdc0 drive 0 1070disk fd1 at fdc0 drive 1 1071 1072# 1073# Other standard PC hardware: `lpt', `mse', `sio', etc. 1074# 1075# lpt: printer port 1076# lpt specials: 1077# The port may be specified as ?. This will cause the 1078# driver to scan the BIOS port list. 1079# The irq clause may be omitted. This will force the port 1080# into polling mode. 1081# mse: Logitech and ATI InPort bus mouse ports 1082# sio: serial ports (see sio(4)) 1083 1084device lpt0 at isa? port? tty irq 7 1085device lpt1 at isa? port "IO_LPT3" tty irq 5 1086device mse0 at isa? port 0x23c tty irq 5 1087 1088device sio0 at isa? port "IO_COM1" tty flags 0x10 irq 4 1089 1090# 1091# `flags' for serial drivers that support consoles (only for sio now): 1092# 0x10 enable console support for this unit. The other console flags 1093# are ignored unless this is set. Enabling console support does 1094# not make the unit the preferred console - boot with -h or set 1095# the 0x20 flag for that. Currently, at most one unit can have 1096# console support; the first one (in config file order) with 1097# this flag set is preferred. Setting this flag for sio0 gives 1098# the old behaviour. 1099# 0x20 force this unit to be the console (unless there is another 1100# higher priority console). This replaces the COMCONSOLE option. 1101# 0x40 reserve this unit for low level console operations. Do not 1102# access the device in any normal way. 1103# 1104# PnP `flags' (set via userconfig using pnp x flags y) 1105# 0x1 disable probing of this device. Used to prevent your modem 1106# from being attached as a PnP modem. 1107# 1108 1109# Options for serial drivers that support consoles (only for sio now): 1110options BREAK_TO_DEBUGGER #a BREAK on a comconsole goes to 1111 #DDB, if available. 1112options CONSPEED=9600 #default speed for serial console (default 9600) 1113 1114# Options for sio: 1115options COM_ESP #code for Hayes ESP 1116options COM_MULTIPORT #code for some cards with shared IRQs 1117options "EXTRA_SIO=2" #number of extra sio ports to allocate 1118 1119# Other flags for sio that aren't documented in the man page. 1120# 0x20000 enable hardware RTS/CTS and larger FIFOs. Only works for 1121# ST16650A-compatible UARTs. 1122 1123# 1124# Network interfaces: `cx', `ed', `el', `ep', `ie', `is', `le', `lnc' 1125# 1126# ar: Arnet SYNC/570i hdlc sync 2/4 port V.35/X.21 serial driver (requires sppp) 1127# cs: IBM Etherjet and other Crystal Semi CS89x0-based adapters 1128# cx: Cronyx/Sigma multiport sync/async (with Cisco or PPP framing) 1129# ed: Western Digital and SMC 80xx; Novell NE1000 and NE2000; 3Com 3C503 1130# el: 3Com 3C501 (slow!) 1131# ep: 3Com 3C509 (buggy) 1132# ex: Intel EtherExpress Pro/10 and other i82595-based adapters 1133# fe: Fujitsu MB86960A/MB86965A Ethernet 1134# ie: AT&T StarLAN 10 and EN100; 3Com 3C507; unknown NI5210; Intel EtherExpress 1135# le: Digital Equipment EtherWorks 2 and EtherWorks 3 (DEPCA, DE100, 1136# DE101, DE200, DE201, DE202, DE203, DE204, DE205, DE422) 1137# lnc: Lance/PCnet cards (Isolan, Novell NE2100, NE32-VL, AMD Am7990 & Am79C960) 1138# rdp: RealTek RTL 8002-based pocket ethernet adapters 1139# sr: RISCom/N2 hdlc sync 1/2 port V.35/X.21 serial driver (requires sppp) 1140# wl: Lucent Wavelan (ISA card only). 1141# ze: IBM/National Semiconductor PCMCIA ethernet controller. 1142# zp: 3Com PCMCIA Etherlink III (It does not require shared memory for 1143# send/receive operation, but it needs 'iomem' to read/write the 1144# attribute memory) 1145# 1146 1147device ar0 at isa? port 0x300 net irq 10 iomem 0xd0000 1148device cs0 at isa? port 0x300 net irq ? 1149device cx0 at isa? port 0x240 net irq 15 drq 7 1150device ed0 at isa? port 0x280 net irq 5 iomem 0xd8000 1151device el0 at isa? port 0x300 net irq 9 1152device ep0 at isa? port 0x300 net irq 10 1153device ex0 at isa? port? net irq? 1154device fe0 at isa? port 0x300 net irq ? 1155device ie0 at isa? port 0x300 net irq 5 iomem 0xd0000 1156device ie1 at isa? port 0x360 net irq 7 iomem 0xd0000 1157device le0 at isa? port 0x300 net irq 5 iomem 0xd0000 1158device lnc0 at isa? port 0x280 net irq 10 drq 0 1159device rdp0 at isa? port 0x378 net irq 7 flags 2 1160device sr0 at isa? port 0x300 net irq 5 iomem 0xd0000 1161options WLCACHE # enables the signal-strength cache 1162options WLDEBUG # enables verbose debugging output 1163device wl0 at isa? port 0x300 net irq ? 1164# We can (bogusly) include both the dedicated PCCARD drivers and the generic 1165# support when COMPILING_LINT. 1166device ze0 at isa? port 0x300 net irq 5 iomem 0xd8000 1167device zp0 at isa? port 0x300 net irq 10 iomem 0xd8000 1168 1169# 1170# ATM related options 1171# 1172# The `en' device provides support for Efficient Networks (ENI) 1173# ENI-155 PCI midway cards, and the Adaptec 155Mbps PCI ATM cards (ANA-59x0). 1174# 1175# atm pseudo-device provides generic atm functions and is required for 1176# atm devices. 1177# NATM enables the netnatm protocol family that can be used to 1178# bypass TCP/IP. 1179# 1180# the current driver supports only PVC operations (no atm-arp, no multicast). 1181# for more details, please read the original documents at 1182# http://www.ccrc.wustl.edu/pub/chuck/bsdatm/wucs.html 1183# 1184pseudo-device atm 1185device en0 1186device en1 1187options NATM #native ATM 1188 1189# 1190# Audio drivers: `snd', `sb', `pas', `gus', `pca' 1191# 1192# snd: Voxware sound support code 1193# sb: SoundBlaster PCM - SoundBlaster, SB Pro, SB16, ProAudioSpectrum 1194# sbxvi: SoundBlaster 16 1195# sbmidi: SoundBlaster 16 MIDI interface 1196# pas: ProAudioSpectrum PCM and MIDI 1197# gus: Gravis Ultrasound - Ultrasound, Ultrasound 16, Ultrasound MAX 1198# gusxvi: Gravis Ultrasound 16-bit PCM (do not use) 1199# mss: Microsoft Sound System 1200# css: Crystal Sound System (CSS 423x PnP) 1201# sscape: Ensoniq Soundscape MIDI interface 1202# sscape_mss: Ensoniq Soundscape PCM (requires sscape) 1203# opl: Yamaha OPL-2 and OPL-3 FM - SB, SB Pro, SB 16, ProAudioSpectrum 1204# uart: stand-alone 6850 UART for MIDI 1205# mpu: Roland MPU-401 stand-alone card 1206# 1207# Beware! The addresses specified below are also hard-coded in 1208# i386/isa/sound/sound_config.h. If you change the values here, you 1209# must also change the values in the include file. 1210# 1211# pcm: PCM audio through various sound cards. 1212# 1213# This has support for a large number of new audio cards, based on 1214# CS423x, OPTi931, Yamaha OPL-SAx, and also for SB16, GusPnP. 1215# For more information about this driver and supported cards, 1216# see the pcm.4 man page and /sys/i386/isa/snd/CARDS. 1217# 1218# The flags of the device tells the device a bit more info about the 1219# device that normally is obtained through the PnP interface. 1220# bit 2..0 secondary DMA channel; 1221# bit 4 set if the board uses two dma channels; 1222# bit 15..8 board type, overrides autodetection; leave it 1223# zero if don't know what to put in (and you don't, 1224# since this is unsupported at the moment...). 1225# 1226# This driver will use the new PnP code if it's available. 1227# 1228# pca: PCM audio through your PC speaker 1229# 1230# If you have a GUS-MAX card and want to use the CS4231 codec on the 1231# card the drqs for the gus max must be 8 bit (1, 2, or 3). 1232# 1233# If you would like to use the full duplex option on the gus, then define 1234# flags to be the ``read dma channel''. 1235# 1236# options BROKEN_BUS_CLOCK #PAS-16 isn't working and OPTI chipset 1237# options SYMPHONY_PAS #PAS-16 isn't working and SYMPHONY chipset 1238# options EXCLUDE_SBPRO #PAS-16 1239# options SBC_IRQ=5 #PAS-16. Must match irq on sb0 line. 1240# PAS16: The order of the pas0/sb0/opl0 is important since the 1241# sb emulation is enabled in the pas-16 attach. 1242# 1243# To overide the GUS defaults use: 1244# options GUS_DMA2 1245# options GUS_DMA 1246# options GUS_IRQ 1247# 1248# The i386/isa/sound/sound.doc has more information. 1249 1250# Controls all "VOXWARE" driver sound devices. See Luigi's driver 1251# below for an alternate which may work better for some cards. 1252# 1253controller snd0 1254device pas0 at isa? port 0x388 irq 10 drq 6 1255device sb0 at isa? port 0x220 irq 5 drq 1 1256device sbxvi0 at isa? drq 5 1257device sbmidi0 at isa? port 0x330 1258device awe0 at isa? port 0x620 1259device gus0 at isa? port 0x220 irq 12 drq 1 1260#device gus0 at isa? port 0x220 irq 12 drq 1 flags 0x3 1261device mss0 at isa? port 0x530 irq 10 drq 1 1262device css0 at isa? port 0x534 irq 5 drq 1 flags 0x08 1263device sscape0 at isa? port 0x330 irq 9 drq 0 1264device trix0 at isa? port 0x330 irq 6 drq 0 1265device sscape_mss0 at isa? port 0x534 irq 5 drq 1 1266device opl0 at isa? port 0x388 1267device mpu0 at isa? port 0x330 irq 6 drq 0 1268device uart0 at isa? port 0x330 irq 5 1269 1270# Luigi's snd code (use INSTEAD of snd0 and all VOXWARE drivers!). 1271# You may also wish to enable the pnp controller with this, for pnp 1272# sound cards. 1273# 1274#device pcm0 at isa? port ? tty irq 10 drq 1 flags 0x0 1275 1276# Not controlled by `snd' 1277device pca0 at isa? port "IO_TIMER1" tty 1278 1279# 1280# Miscellaneous hardware: 1281# 1282# mcd: Mitsumi CD-ROM 1283# scd: Sony CD-ROM 1284# matcd: Matsushita/Panasonic CD-ROM 1285# wt: Wangtek and Archive QIC-02/QIC-36 tape drives 1286# ctx: Cortex-I frame grabber 1287# apm: Laptop Advanced Power Management (experimental) 1288# spigot: The Creative Labs Video Spigot video-acquisition board 1289# meteor: Matrox Meteor video capture board 1290# bktr: Brooktree bt848/848a/849/878/879 family video capture and TV Tuner board 1291# alog: Industrial Computer Source AIO8-P driver 1292# cy: Cyclades serial driver 1293# dgb: Digiboard PC/Xi and PC/Xe series driver (ALPHA QUALITY!) 1294# dgm: Digiboard PC/Xem driver 1295# gp: National Instruments AT-GPIB and AT-GPIB/TNT board 1296# asc: GI1904-based hand scanners, e.g. the Trust Amiscan Grey 1297# gsc: Genius GS-4500 hand scanner. 1298# joy: joystick 1299# labpc: National Instrument's Lab-PC and Lab-PC+ 1300# rc: RISCom/8 multiport card 1301# rp: Comtrol Rocketport(ISA) - single card 1302# tw: TW-523 power line interface for use with X-10 home control products 1303# si: Specialix SI/XIO 4-32 port terminal multiplexor 1304# stl: Stallion EasyIO and EasyConnection 8/32 (cd1400 based) 1305# stli: Stallion EasyConnection 8/64, ONboard, Brumby (intelligent) 1306 1307# 1308# Notes on APM 1309# The flags takes the following meaning for apm0: 1310# 0x0020 Statclock is broken. 1311# 0x0011 Limit APM protocol to 1.1 or 1.0 1312# 0x0010 Limit APM protocol to 1.0 1313# 1314# 1315# Notes on the spigot: 1316# The video spigot is at 0xad6. This port address can not be changed. 1317# The irq values may only be 10, 11, or 15 1318# I/O memory is an 8kb region. Possible values are: 1319# 0a0000, 0a2000, ..., 0fffff, f00000, f02000, ..., ffffff 1320# The start address must be on an even boundary. 1321# Add the following option if you want to allow non-root users to be able 1322# to access the spigot. This option is not secure because it allows users 1323# direct access to the I/O page. 1324# options SPIGOT_UNSECURE 1325# 1326 1327# Notes on the Comtrol Rocketport driver: 1328# 1329# The exact values used for rp0 depend on how many boards you have 1330# in the system. The manufacturer's sample configs are listed as: 1331# 1332# Comtrol Rocketport ISA single card 1333# device rp0 at isa? port 0x280 tty 1334# 1335# If instead you have two ISA cards, one installed at 0x100 and the 1336# second installed at 0x180, then you should add the following to 1337# your kernel configuration file: 1338# 1339# device rp0 at isa? port 0x100 tty 1340# device rp1 at isa? port 0x180 tty 1341# 1342# For 4 ISA cards, it might be something like this: 1343# 1344# device rp0 at isa? port 0x180 tty 1345# device rp1 at isa? port 0x100 tty 1346# device rp2 at isa? port 0x340 tty 1347# device rp3 at isa? port 0x240 tty 1348# 1349# And for PCI cards, you only need say: 1350# 1351# device rp0 1352# device rp1 1353# ... 1354# Note: Make sure that any Rocketport PCI devices are specified BEFORE the 1355# ISA Rocketport devices. 1356 1357# Notes on the Digiboard driver: 1358# 1359# The following flag values have special meanings: 1360# 0x01 - alternate layout of pins (dgb & dgm) 1361# 0x02 - use the windowed PC/Xe in 64K mode (dgb only) 1362 1363# Notes on the Specialix SI/XIO driver: 1364# **This is NOT a Specialix supported Driver!** 1365# The host card is memory, not IO mapped. 1366# The Rev 1 host cards use a 64K chunk, on a 32K boundary. 1367# The Rev 2 host cards use a 32K chunk, on a 32K boundary. 1368# The cards can use an IRQ of 11, 12 or 15. 1369 1370# Notes on the Stallion stl and stli drivers: 1371# See src/i386/isa/README.stl for complete instructions. 1372# This is version 0.0.5alpha, unsupported by Stallion. 1373# The stl driver has a secondary IO port hard coded at 0x280. You need 1374# to change src/i386/isa/stallion.c if you reconfigure this on the boards. 1375# The "flags" and "iosiz" settings on the stli driver depend on the board: 1376# EasyConnection 8/64 ISA: flags 23 iosiz 0x1000 1377# EasyConnection 8/64 EISA: flags 24 iosiz 0x10000 1378# EasyConnection 8/64 MCA: flags 25 iosiz 0x1000 1379# ONboard ISA: flags 4 iosiz 0x10000 1380# ONboard EISA: flags 7 iosiz 0x10000 1381# ONboard MCA: flags 3 iosiz 0x10000 1382# Brumby: flags 2 iosiz 0x4000 1383# Stallion: flags 1 iosiz 0x10000 1384 1385device mcd0 at isa? port 0x300 bio irq 10 1386# for the Sony CDU31/33A CDROM 1387device scd0 at isa? port 0x230 bio 1388# for the SoundBlaster 16 multicd - up to 4 devices 1389controller matcd0 at isa? port 0x230 bio 1390device wt0 at isa? port 0x300 bio irq 5 drq 1 1391device ctx0 at isa? port 0x230 iomem 0xd0000 1392device spigot0 at isa? port 0xad6 irq 15 iomem 0xee000 1393device apm0 at isa? 1394device gp0 at isa? port 0x2c0 tty 1395device gsc0 at isa? port "IO_GSC1" tty drq 3 1396device joy0 at isa? port IO_GAME 1397device alog0 at isa? port 0x260 tty irq 5 1398device cy0 at isa? tty irq 10 iomem 0xd4000 iosiz 0x2000 1399device dgb0 at isa? port 0x220 iomem 0xfc0000 iosiz ? tty 1400device dgm0 at isa? port 0x104 iomem 0xd00000 iosiz ? tty 1401device labpc0 at isa? port 0x260 tty irq 5 1402device rc0 at isa? port 0x220 tty irq 12 1403device rp0 at isa? port 0x280 tty 1404# the port and irq for tw0 are fictitious 1405device tw0 at isa? port 0x380 tty irq 11 1406device si0 at isa? iomem 0xd0000 tty irq 12 1407device asc0 at isa? port "IO_ASC1" tty drq 3 irq 10 1408device stl0 at isa? port 0x2a0 tty irq 10 1409device stli0 at isa? port 0x2a0 tty iomem 0xcc000 flags 23 iosiz 0x1000 1410# You are unlikely to have the hardware for loran0 <phk@FreeBSD.org> 1411device loran0 at isa? port ? tty irq 5 1412# HOT1 Xilinx 6200 card (www.vcc.com) 1413device xrpu0 1414 1415# 1416# EISA devices: 1417# 1418# The EISA bus device is eisa0. It provides auto-detection and 1419# configuration support for all devices on the EISA bus. 1420# 1421# The `ahb' device provides support for the Adaptec 174X adapter. 1422# 1423# The `ahc' device provides support for the Adaptec 274X and 284X 1424# adapters. The 284X, although a VLB card responds to EISA probes. 1425# 1426# fea: DEC DEFEA EISA FDDI adapter 1427# 1428controller eisa0 1429controller ahb0 1430controller ahc0 1431device fea0 1432 1433# The aic7xxx driver will attempt to use memory mapped I/O for all PCI 1434# controllers that have it configured only if this option is set. Unfortunately, 1435# this doesn't work on some motherboards, which prevents it from being the 1436# default. 1437options AHC_ALLOW_MEMIO 1438 1439# By default, only 10 EISA slots are probed, since the slot numbers 1440# above clash with the configuration address space of the PCI subsystem, 1441# and the EISA probe is not very smart about this. This is sufficient 1442# for most machines, but in particular the HP NetServer LC series comes 1443# with an onboard AIC7770 dual-channel SCSI controller on EISA slot #11, 1444# thus you need to bump this figure to 12 for them. 1445options "EISA_SLOTS=12" 1446 1447# 1448# PCI devices & PCI options: 1449# 1450# The main PCI bus device is `pci'. It provides auto-detection and 1451# configuration support for all devices on the PCI bus, using either 1452# configuration mode defined in the PCI specification. 1453# 1454# The `ahc' device provides support for the Adaptec 29/3940(U)(W) 1455# and motherboard based AIC7870/AIC7880 adapters. 1456# 1457# The `ncr' device provides support for the NCR 53C810 and 53C825 1458# self-contained SCSI host adapters. 1459# 1460# The `isp' device provides support for the Qlogic ISP 1020, 1040 1461# nd 1040B PCI SCSI host adapters, as well as the Qlogic ISP 2100 1462# FC/AL Host Adapter. 1463# 1464# The `ax' device provides support for PCI fast ethernet adapters 1465# based on the ASIX Electronics AX88140A chip, including the Alfa 1466# Inc. GFC2204. 1467# 1468# The `de' device provides support for the Digital Equipment DC21040 1469# self-contained Ethernet adapter. 1470# 1471# The `fxp' device provides support for the Intel EtherExpress Pro/100B 1472# PCI Fast Ethernet adapters. 1473# 1474# The `mx' device provides support for various fast ethernet adapters 1475# based on the Macronix 98713, 987615 ans 98725 series chips. 1476# 1477# The `pn' device provides support for various fast ethernet adapters 1478# based on the Lite-On 82c168 and 82c169 PNIC chips, including the 1479# LinkSys LNE100TX, the NetGear FA310TX rev. D1 and the Matrox 1480# FastNIC 10/100. 1481# 1482# The 'rl' device provides support for PCI fast ethernet adapters based 1483# on the RealTek 8129/8139 chipset. Note that the RealTek driver defaults 1484# to useing programmed I/O to do register accesses because memory mapped 1485# mode seems to cause severe lockups on SMP hardware. This driver also 1486# supports the Accton EN1207D `Cheetah' adapter, which uses a chip called 1487# the MPX 5030/5038, which is either a RealTek in disguise or a RealTek 1488# workalike. 1489# 1490# The 'tl' device provides support for the Texas Instruments TNETE100 1491# series 'ThunderLAN' cards and integrated ethernet controllers. This 1492# includes several Compaq Netelligent 10/100 cards and the built-in 1493# ethernet controllers in several Compaq Prosignia, Proliant and 1494# Deskpro systems. It also supports several Olicom 10Mbps and 10/100 1495# boards. 1496# 1497# The `tx' device provides support for the SMC 9432TX cards. 1498# 1499# The `vr' device provides support for various fast ethernet adapters 1500# based on the VIA Technologies VT3043 `Rhine I' and VT86C100A `Rhine II' 1501# chips, including the D-Link DFE530TX. 1502# 1503# The `vx' device provides support for the 3Com 3C590 and 3C595 1504# early support 1505# 1506# The `wb' device provides support for various fast ethernet adapters 1507# based on the Winbond W89C840F chip. Note: this is not the same as 1508# the Winbond W89C940F, which is an NE2000 clone. 1509# 1510# The `xl' device provides support for the 3Com 3c900, 3c905 and 1511# 3c905B (Fast) Etherlink XL cards and integrated controllers. This 1512# includes the integrated 3c905B-TX chips in certain Dell Optiplex and 1513# Dell Precision desktop machines and the integrated 3c905-TX chips 1514# in Dell Latitude laptop docking stations. 1515# 1516# The `fpa' device provides support for the Digital DEFPA PCI FDDI 1517# adapter. pseudo-device fddi is also needed. 1518# 1519# The `meteor' device is a PCI video capture board. It can also have the 1520# following options: 1521# options METEOR_ALLOC_PAGES=xxx preallocate kernel pages for data entry 1522# figure (ROWS*COLUMN*BYTES_PER_PIXEL*FRAME+PAGE_SIZE-1)/PAGE_SIZE 1523# options METEOR_DEALLOC_PAGES remove all allocated pages on close(2) 1524# options METEOR_DEALLOC_ABOVE=xxx remove all allocated pages above the 1525# specified amount. If this value is below the allocated amount no action 1526# taken 1527# option METEOR_SYSTEM_DEFAULT={METEOR_PAL|METEOR_NTSC|METEOR_SECAM}, used 1528# for initialization of fps routine when a signal is not present. 1529# 1530# The 'bktr' device is a PCI video capture device using the Brooktree 1531# bt848/bt848a/bt849/bt878/bt879 chipset. When used with a TV Tuner it forms a 1532# TV card, eg Miro PC/TV,Hauppauge WinCast/TV WinTV, VideoLogic Captivator, 1533# Intel Smart Video III, AverMedia, IMS Turbo. 1534# The following options can be used to override the auto detection 1535# options OVERRIDE_CARD=xxx 1536# options OVERRIDE_TUNER=xxx 1537# options OVERRIDE_MSP=1 1538# options OVERRIDE_DBX=1 1539# The current values are found in /usr/src/sys/pci/brooktree848.c 1540# 1541# option BROOKTREE_SYSTEM_DEFAULT=BROOKTREE_PAL 1542# This is required for Dual Crystal (28&35Mhz) boards where PAL is used 1543# to prevent hangs during initialisation. eg VideoLogic Captivator PCI. 1544# 1545# PAL or SECAM users who have a 28Mhz crystal (and no 35Mhz crystal) 1546# must enable PLL mode with this option. eg some new Hauppauge cards. 1547# option BKTR_USE_PLL 1548# 1549# Using sysctl(8) run-time overrides on a per-card basis can be made 1550# 1551controller pci0 1552controller ahc1 1553controller ncr0 1554controller isp0 1555device ax0 1556device de0 1557device fxp0 1558device mx0 1559device pn0 1560device rl0 1561device tl0 1562device tx0 1563device vr0 1564device vx0 1565device wb0 1566device xl0 1567device fpa0 1568device meteor0 1569 1570# Brooktree driver has been ported to the new I2C framework. Thus, 1571# you'll need at least iicbus, iicbb and smbus. iic/smb are only needed if you 1572# want to control other I2C slaves connected to the external connector of 1573# some cards. 1574# 1575device bktr0 1576 1577# 1578# PCI options 1579# 1580#options PCI_QUIET #quiets PCI code on chipset settings 1581 1582# 1583# PCCARD/PCMCIA 1584# 1585# card: slot controller 1586# pcic: slots 1587controller card0 1588device pcic0 at card? 1589device pcic1 at card? 1590 1591# You may need to reset all pccards after resuming 1592options PCIC_RESUME_RESET # reset after resume 1593 1594# 1595# Laptop/Notebook options: 1596# 1597# See also: 1598# apm under `Miscellaneous hardware' 1599# above. 1600 1601# For older notebooks that signal a powerfail condition (external 1602# power supply dropped, or battery state low) by issuing an NMI: 1603 1604options POWERFAIL_NMI # make it beep instead of panicing 1605 1606# 1607# SMB bus 1608# 1609# System Management Bus support provided by the 'smbus' device. 1610# 1611# Supported devices: 1612# smb standard io 1613# 1614# Supported interfaces: 1615# iicsmb I2C to SMB bridge with any iicbus interface 1616# bktr brooktree848 I2C hardware interface 1617# 1618controller smbus0 1619 1620device smb0 at smbus? 1621 1622# 1623# I2C Bus 1624# 1625# Philips i2c bus support is provided by the `iicbus' device. 1626# 1627# Supported devices: 1628# ic i2c network interface 1629# iic i2c standard io 1630# iicsmb i2c to smb bridge. Allow i2c i/o with smb commands. 1631# 1632# Supported interfaces: 1633# pcf Philips PCF8584 ISA-bus controller 1634# bktr brooktree848 I2C software interface 1635# 1636# Other: 1637# iicbb generic I2C bit-banging code (needed by lpbb, bktr) 1638# 1639controller iicbus0 1640controller iicbb0 1641 1642device ic0 at iicbus? 1643device iic0 at iicbus? 1644device iicsmb0 at iicbus? 1645 1646controller pcf0 at isa? port 0x320 net irq 5 1647 1648# ISDN4BSD section 1649 1650# i4b passive ISDN cards support (isic - I4b Siemens Isdn Chipset driver) 1651# note that the ``options'' and ``device'' lines must BOTH be defined ! 1652# 1653# Non-PnP Cards: 1654# -------------- 1655# 1656# Teles S0/8 or Niccy 1008 1657options "TEL_S0_8" 1658#device isic0 at isa? iomem 0xd0000 net irq 5 flags 1 1659# 1660# Teles S0/16 or Creatix ISDN-S0 or Niccy 1016 1661options "TEL_S0_16" 1662#device isic0 at isa? port 0xd80 iomem 0xd0000 net irq 5 flags 2 1663# 1664# Teles S0/16.3 1665options "TEL_S0_16_3" 1666#device isic0 at isa? port 0xd80 net irq 5 flags 3 1667# 1668# AVM A1 or AVM Fritz!Card 1669options "AVM_A1" 1670#device isic0 at isa? port 0x340 net irq 5 flags 4 1671# 1672# USRobotics Sportster ISDN TA intern 1673options "USR_STI" 1674#device isic0 at isa? port 0x268 net irq 5 flags 7 1675# 1676# ITK ix1 Micro 1677options "ITKIX1" 1678#device isic0 at isa? port 0x398 net irq 10 flags 18 1679# 1680# PnP-Cards: 1681# ---------- 1682# 1683# Teles S0/16.3 PnP 1684options "TEL_S0_16_3_P" 1685#device isic0 at isa? port ? net irq ? 1686# 1687# Creatix ISDN-S0 P&P 1688options "CRTX_S0_P" 1689#device isic0 at isa? port ? net irq ? 1690# 1691# Dr. Neuhaus Niccy Go@ 1692options "DRN_NGO" 1693#device isic0 at isa? port ? net irq ? 1694# 1695# Sedlbauer Win Speed 1696options "SEDLBAUER" 1697#device isic0 at isa? port ? net irq ? 1698# 1699# Dynalink IS64PH 1700options "DYNALINK" 1701#device isic0 at isa? port ? net irq ? 1702# 1703# ELSA QuickStep 1000pro ISA 1704options "ELSA_QS1ISA" 1705#device isic0 at isa? port ? net irq ? 1706# 1707# PCI-Cards: 1708# ---------- 1709# 1710# ELSA QuickStep 1000pro PCI 1711options "ELSA_QS1PCI" 1712#device isic0 1713# 1714# PCMCIA-Cards: 1715# ------------- 1716# 1717# AVM PCMCIA Fritz!Card 1718options "AVM_A1_PCMCIA" 1719device isic0 at isa? port 0x340 net irq 5 flags 10 1720# 1721# Active Cards: 1722# ------------- 1723# 1724# Stollmann Tina-dd control device 1725device tina0 at isa? port 0x260 net irq 10 1726# 1727# ISDN Protocol Stack 1728# ------------------- 1729# 1730# Q.921 / layer 2 - i4b passive cards D channel handling 1731pseudo-device "i4bq921" 1732# 1733# Q.931 / layer 3 - i4b passive cards D channel handling 1734pseudo-device "i4bq931" 1735# 1736# layer 4 - i4b common passive and active card handling 1737pseudo-device "i4b" 1738# 1739# ISDN devices 1740# ------------ 1741# 1742# userland driver to do ISDN tracing (for passive cards only) 1743pseudo-device "i4btrc" 4 1744# 1745# userland driver to control the whole thing 1746pseudo-device "i4bctl" 1747# 1748# userland driver for access to raw B channel 1749pseudo-device "i4brbch" 4 1750# 1751# userland driver for telephony 1752pseudo-device "i4btel" 2 1753# 1754# network driver for IP over raw HDLC ISDN 1755pseudo-device "i4bipr" 4 1756# enable VJ header compression detection for ipr i/f 1757options IPR_VJ 1758# 1759# network driver for sync PPP over ISDN 1760pseudo-device "i4bisppp" 4 1761 1762 1763# Parallel-Port Bus 1764# 1765# Parallel port bus support is provided by the `ppbus' device. 1766# Multiple devices may be attached to the parallel port, devices 1767# are automatically probed and attached when found. 1768# 1769# Supported devices: 1770# vpo Iomega Zip Drive 1771# Requires SCSI disk support ('scbus' and 'da'), best 1772# performance is achieved with ports in EPP 1.9 mode. 1773# nlpt Parallel Printer, use _instead_ of lpt0 1774# plip Parallel network interface 1775# ppi General-purpose I/O ("Geek Port") 1776# pps Pulse per second Timing Interface 1777# lpbb Philips official parallel port I2C bit-banging interface 1778# 1779# Supported interfaces: 1780# ppc ISA-bus parallel port interfaces. 1781# 1782controller ppbus0 1783controller vpo0 at ppbus? 1784device nlpt0 at ppbus? 1785device plip0 at ppbus? 1786device ppi0 at ppbus? 1787device pps0 at ppbus? 1788device lpbb0 at ppbus? 1789 1790controller ppc0 at isa? disable port ? tty irq 7 1791 1792# Kernel BOOTP support 1793 1794options BOOTP # Use BOOTP to obtain IP address/hostname 1795options BOOTP_NFSROOT # NFS mount root filesystem using BOOTP info 1796options "BOOTP_NFSV3" # Use NFS v3 to NFS mount root 1797options BOOTP_COMPAT # Workaround for broken bootp daemons. 1798options "BOOTP_WIRED_TO=fxp0" # Use interface fxp0 for BOOTP 1799 1800# If you want to disable loadable kernel modules (LKM), you 1801# might want to use this option. 1802#options NO_LKM 1803 1804# 1805# Add tie-ins for a hardware watchdog. This only enable the hooks; 1806# the user must still supply the actual driver. 1807# 1808options HW_WDOG 1809 1810# 1811# Set the number of PV entries per process. Increasing this can 1812# stop panics related to heavy use of shared memory. However, that can 1813# (combined with large amounts of physical memory) cause panics at 1814# boot time due the kernel running out of VM space. 1815# 1816# If you're tweaking this, you might also want to increase the sysctls 1817# "vm.v_free_min", "vm.v_free_reserved", and "vm.v_free_target". 1818# 1819# The value below is the one more than the default. 1820# 1821options "PMAP_SHPGPERPROC=201" 1822 1823# 1824# Disable swapping. This option removes all code which actually performs 1825# swapping, so it's not possible to turn it back on at run-time. 1826# 1827# This is sometimes usable for systems which don't have any swap space 1828# (see also sysctls "vm.defer_swapspace_pageouts" and 1829# "vm.disable_swapspace_pageouts") 1830# 1831#options NO_SWAPPING 1832 1833# Set the number of sf_bufs to allocate. sf_bufs are virtual buffers 1834# for sendfile(2) that are used to map file VM pages, and normally 1835# default to a quantity that is roughly 16*MAXUSERS+512. You would 1836# typically want about 4 of these for each simultaneous file send. 1837# 1838options "NSFBUFS=1024" 1839 1840# More undocumented options for linting. 1841 1842options CLK_CALIBRATION_LOOP 1843options "CLK_USE_I8254_CALIBRATION" 1844options CLK_USE_TSC_CALIBRATION 1845options CLUSTERDEBUG 1846options COMPAT_LINUX 1847options CPU_UPGRADE_HW_CACHE 1848options DEBUG 1849options "DEBUG_1284" 1850#options DISABLE_PSE 1851options "EXT2FS" 1852options "I586_PMC_GUPROF=0x70000" 1853options "IBCS2" 1854options KEY 1855options KEY_DEBUG 1856options LOCKF_DEBUG 1857options LOUTB 1858options KBD_MAXRETRY=4 1859options KBD_MAXWAIT=6 1860options KBD_RESETDELAY=201 1861options KBDIO_DEBUG=2 1862options MSGMNB=2049 1863options MSGMNI=41 1864options MSGSEG=2049 1865options MSGSSZ=16 1866options MSGTQL=41 1867options NBUF=512 1868options NETATALKDEBUG 1869options NMBCLUSTERS=1024 1870options NPX_DEBUG 1871options PANIC_REBOOT_WAIT_TIME=16 1872options "PCVT_24LINESDEF" 1873options PCVT_CTRL_ALT_DEL 1874options PCVT_EMU_MOUSE 1875options PCVT_FREEBSD=211 1876options PCVT_META_ESC 1877options PCVT_NSCREENS=9 1878options PCVT_PRETTYSCRNS 1879options PCVT_SCREENSAVER 1880options PCVT_USEKBDSEC 1881options "PCVT_VT220KEYB" 1882options PSM_DEBUG=1 1883options SCSI_NCR_DEBUG 1884options SCSI_NCR_DFLT_TAGS=4 1885options SCSI_NCR_MAX_SYNC=10000 1886options SCSI_NCR_MAX_WIDE=1 1887options SCSI_NCR_MYADDR=7 1888options SEMMAP=31 1889options SEMMNI=11 1890options SEMMNS=61 1891options SEMMNU=31 1892options SEMMSL=61 1893options SEMOPM=101 1894options SEMUME=11 1895options SHOW_BUSYBUFS # List buffers that prevent root unmount 1896options SHMALL=1025 1897options "SHMMAX=(SHMMAXPGS*PAGE_SIZE+1)" 1898options SHMMAXPGS=1025 1899options SHMMIN=2 1900options SHMMNI=33 1901options SHMSEG=9 1902options SI_DEBUG 1903options SIMPLELOCK_DEBUG 1904options SPX_HACK 1905options VFS_BIO_DEBUG 1906 1907# The 'dpt' driver provides support for DPT controllers (http://www.dpt.com/). 1908# These have hardware RAID-{0,1,5} support, and do multi-initiator I/O. 1909# The DPT controllers are commonly re-licensed under other brand-names - 1910# some controllers by Olivetti, Dec, HP, AT&T, SNI, AST, Alphatronic, NEC and 1911# Compaq are actually DPT controllers. 1912# 1913# See sys/dev/dpt for debugging and other subtle options. 1914# DPT_VERIFY_HINTR Performs some strict hardware interrupts testing. 1915# Only use if you suspect PCI bus corruption problems 1916# DPT_RESTRICTED_FREELIST Normally, the freelisat used by the DPT for queue 1917# will grow to accomodate increased use. This growth 1918# will NOT shrink. To restrict the number of queue 1919# slots to exactly what the DPT can hold at one time, 1920# enable this option. 1921# DPT_MEASURE_PERFORMANCE Enables a set of (semi)invasive metrics. Various 1922# instruments are enabled. The tools in 1923# /usr/sbin/dpt_* assume these to be enabled. 1924# DPT_FREELIST_IS_STACK For optimal L{1,2} CPU cache utilization, enable 1925# this option. Otherwise, the transaction queue is 1926# a LIFO. I cannot measure the performance gain. 1927# DPT_HANDLE_TIMEOUTS Normally device timeouts are handled by the DPT. 1928# If you ant the driver to handle timeouts, enable 1929# this option. If your system is very busy, this 1930# option will create more trouble than solve. 1931# DPT_TIMEOUT_FACTOR Used to compute the excessive amount of time to 1932# wait when timing out with the above option. 1933# DPT_DEBUG_xxxx These are controllable from sys/dev/dpt/dpt.h 1934# DPT_LOST_IRQ When enabled, will try, once per second, to catch 1935# any interrupt that got lost. Seems to help in some 1936# DPT-firmware/Motherboard combinations. Minimal 1937# cost, great benefit. 1938# DPT_RESET_HBA Make "reset" actually reset the controller 1939# instead of fudging it. Only enable this if you 1940# are 100% certain you need it. 1941# DPT_SHUTDOWN_SLEEP Reset controller if a request take more than 1942# this number of seconds. Do NOT enable this 1943# unless you are really, really, really certain 1944# you need it. You are advised to call Simon (the 1945# driver author) before setting it, and NEVER, 1946# EVER set it to less than 300s (5 minutes). 1947 1948controller dpt0 1949 1950# DPT options 1951options DPT_VERIFY_HINTR 1952options DPT_RESTRICTED_FREELIST 1953#!CAM# options DPT_MEASURE_PERFORMANCE 1954options DPT_FREELIST_IS_STACK 1955#!CAM# options DPT_HANDLE_TIMEOUTS 1956options DPT_TIMEOUT_FACTOR=4 1957options DPT_INTR_DELAY=200 # Some motherboards need that 1958options DPT_LOST_IRQ 1959options DPT_RESET_HBA 1960 1961# Don't EVER set this without having talked to Simon Shapiro on the phone 1962# first. 1963options DPT_SHUTDOWN_SLEEP=500 1964 1965# USB support 1966# UHCI controller 1967controller uhci0 1968# OHCI controller 1969controller ohci0 1970# General USB code (mandatory for USB) 1971controller usb0 1972# 1973# for the moment we have to specify the priorities of the device 1974# drivers explicitly by the ordering in the list below. This will 1975# be changed in the future. 1976# 1977# USB mouse 1978device ums0 1979# USB keyboard 1980device ukbd0 1981# USB printer 1982device ulpt0 1983# USB hub (kind of mandatory, no other driver is available for the root hub) 1984device uhub0 1985# USB communications driver 1986device ucom0 1987# USB modem driver 1988device umodem0 1989# Human Interface Device (anything with buttons and dials) 1990device hid0 1991# Generic USB device driver 1992device ugen0 1993# 1994options USB_DEBUG 1995options USBVERBOSE 1996