1 /*- 2 * SPDX-License-Identifier: BSD-2-Clause-FreeBSD 3 * 4 * Copyright (c) 2010 Lev Serebryakov <lev@FreeBSD.org>. 5 * All rights reserved. 6 * 7 * Redistribution and use in source and binary forms, with or without 8 * modification, are permitted provided that the following conditions 9 * are met: 10 * 1. Redistributions of source code must retain the above copyright 11 * notice, this list of conditions and the following disclaimer. 12 * 2. Redistributions in binary form must reproduce the above copyright 13 * notice, this list of conditions and the following disclaimer in the 14 * documentation and/or other materials provided with the distribution. 15 * 16 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND 17 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 18 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 19 * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE 20 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 21 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 22 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 23 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT 24 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 25 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 26 * SUCH DAMAGE. 27 */ 28 29 /* 30 * This driver supports several multiport USB-to-RS232 serial adapters driven 31 * by MosChip mos7820 and mos7840, bridge chips. 32 * The adapters are sold under many different brand names. 33 * 34 * Datasheets are available at MosChip www site at 35 * http://www.moschip.com. The datasheets don't contain full 36 * programming information for the chip. 37 * 38 * It is nornal to have only two enabled ports in devices, based on 39 * quad-port mos7840. 40 * 41 */ 42 #include <sys/cdefs.h> 43 __FBSDID("$FreeBSD$"); 44 45 #include <sys/stdint.h> 46 #include <sys/stddef.h> 47 #include <sys/param.h> 48 #include <sys/queue.h> 49 #include <sys/types.h> 50 #include <sys/systm.h> 51 #include <sys/kernel.h> 52 #include <sys/bus.h> 53 #include <sys/linker_set.h> 54 #include <sys/module.h> 55 #include <sys/lock.h> 56 #include <sys/mutex.h> 57 #include <sys/condvar.h> 58 #include <sys/sysctl.h> 59 #include <sys/sx.h> 60 #include <sys/unistd.h> 61 #include <sys/callout.h> 62 #include <sys/malloc.h> 63 #include <sys/priv.h> 64 65 #include <dev/usb/usb.h> 66 #include <dev/usb/usbdi.h> 67 #include <dev/usb/usbdi_util.h> 68 #include <dev/usb/usb_cdc.h> 69 #include "usbdevs.h" 70 71 #define USB_DEBUG_VAR umcs_debug 72 #include <dev/usb/usb_debug.h> 73 #include <dev/usb/usb_process.h> 74 75 #include <dev/usb/serial/usb_serial.h> 76 77 #include <dev/usb/serial/umcs.h> 78 79 #define UMCS7840_MODVER 1 80 81 #ifdef USB_DEBUG 82 static int umcs_debug = 0; 83 84 static SYSCTL_NODE(_hw_usb, OID_AUTO, umcs, CTLFLAG_RW, 0, "USB umcs quadport serial adapter"); 85 SYSCTL_INT(_hw_usb_umcs, OID_AUTO, debug, CTLFLAG_RWTUN, &umcs_debug, 0, "Debug level"); 86 #endif /* USB_DEBUG */ 87 88 89 /* 90 * Two-port devices (both with 7820 chip and 7840 chip configured as two-port) 91 * have ports 0 and 2, with ports 1 and 3 omitted. 92 * So,PHYSICAL port numbers (indexes) on two-port device will be 0 and 2. 93 * This driver trys to use physical numbers as much as possible. 94 */ 95 96 /* 97 * Indexed by PHYSICAL port number. 98 * Pack non-regular registers to array to easier if-less access. 99 */ 100 struct umcs7840_port_registers { 101 uint8_t reg_sp; /* SP register. */ 102 uint8_t reg_control; /* CONTROL register. */ 103 uint8_t reg_dcr; /* DCR0 register. DCR1 & DCR2 can be 104 * calculated */ 105 }; 106 107 static const struct umcs7840_port_registers umcs7840_port_registers[UMCS7840_MAX_PORTS] = { 108 {.reg_sp = MCS7840_DEV_REG_SP1,.reg_control = MCS7840_DEV_REG_CONTROL1,.reg_dcr = MCS7840_DEV_REG_DCR0_1}, 109 {.reg_sp = MCS7840_DEV_REG_SP2,.reg_control = MCS7840_DEV_REG_CONTROL2,.reg_dcr = MCS7840_DEV_REG_DCR0_2}, 110 {.reg_sp = MCS7840_DEV_REG_SP3,.reg_control = MCS7840_DEV_REG_CONTROL3,.reg_dcr = MCS7840_DEV_REG_DCR0_3}, 111 {.reg_sp = MCS7840_DEV_REG_SP4,.reg_control = MCS7840_DEV_REG_CONTROL4,.reg_dcr = MCS7840_DEV_REG_DCR0_4}, 112 }; 113 114 enum { 115 UMCS7840_BULK_RD_EP, 116 UMCS7840_BULK_WR_EP, 117 UMCS7840_N_TRANSFERS 118 }; 119 120 struct umcs7840_softc_oneport { 121 struct usb_xfer *sc_xfer[UMCS7840_N_TRANSFERS]; /* Control structures 122 * for two transfers */ 123 124 uint8_t sc_lcr; /* local line control register */ 125 uint8_t sc_mcr; /* local modem control register */ 126 }; 127 128 struct umcs7840_softc { 129 struct ucom_super_softc sc_super_ucom; 130 struct ucom_softc sc_ucom[UMCS7840_MAX_PORTS]; /* Need to be continuous 131 * array, so indexed by 132 * LOGICAL port 133 * (subunit) number */ 134 135 struct usb_xfer *sc_intr_xfer; /* Interrupt endpoint */ 136 137 device_t sc_dev; /* Device for error prints */ 138 struct usb_device *sc_udev; /* USB Device for all operations */ 139 struct mtx sc_mtx; /* ucom requires this */ 140 141 uint8_t sc_driver_done; /* Flag when enumeration is finished */ 142 143 uint8_t sc_numports; /* Number of ports (subunits) */ 144 struct umcs7840_softc_oneport sc_ports[UMCS7840_MAX_PORTS]; /* Indexed by PHYSICAL 145 * port number. */ 146 }; 147 148 /* prototypes */ 149 static usb_error_t umcs7840_get_reg_sync(struct umcs7840_softc *, uint8_t, uint8_t *); 150 static usb_error_t umcs7840_set_reg_sync(struct umcs7840_softc *, uint8_t, uint8_t); 151 static usb_error_t umcs7840_get_UART_reg_sync(struct umcs7840_softc *, uint8_t, uint8_t, uint8_t *); 152 static usb_error_t umcs7840_set_UART_reg_sync(struct umcs7840_softc *, uint8_t, uint8_t, uint8_t); 153 154 static usb_error_t umcs7840_set_baudrate(struct umcs7840_softc *, uint8_t, uint32_t); 155 static usb_error_t umcs7840_calc_baudrate(uint32_t rate, uint16_t *, uint8_t *); 156 157 static void umcs7840_free(struct ucom_softc *); 158 static void umcs7840_cfg_get_status(struct ucom_softc *, uint8_t *, uint8_t *); 159 static void umcs7840_cfg_set_dtr(struct ucom_softc *, uint8_t); 160 static void umcs7840_cfg_set_rts(struct ucom_softc *, uint8_t); 161 static void umcs7840_cfg_set_break(struct ucom_softc *, uint8_t); 162 static void umcs7840_cfg_param(struct ucom_softc *, struct termios *); 163 static void umcs7840_cfg_open(struct ucom_softc *); 164 static void umcs7840_cfg_close(struct ucom_softc *); 165 166 static int umcs7840_pre_param(struct ucom_softc *, struct termios *); 167 168 static void umcs7840_start_read(struct ucom_softc *); 169 static void umcs7840_stop_read(struct ucom_softc *); 170 171 static void umcs7840_start_write(struct ucom_softc *); 172 static void umcs7840_stop_write(struct ucom_softc *); 173 174 static void umcs7840_poll(struct ucom_softc *ucom); 175 176 static device_probe_t umcs7840_probe; 177 static device_attach_t umcs7840_attach; 178 static device_detach_t umcs7840_detach; 179 static void umcs7840_free_softc(struct umcs7840_softc *); 180 181 static usb_callback_t umcs7840_intr_callback; 182 static usb_callback_t umcs7840_read_callback1; 183 static usb_callback_t umcs7840_read_callback2; 184 static usb_callback_t umcs7840_read_callback3; 185 static usb_callback_t umcs7840_read_callback4; 186 static usb_callback_t umcs7840_write_callback1; 187 static usb_callback_t umcs7840_write_callback2; 188 static usb_callback_t umcs7840_write_callback3; 189 static usb_callback_t umcs7840_write_callback4; 190 191 static void umcs7840_read_callbackN(struct usb_xfer *, usb_error_t, uint8_t); 192 static void umcs7840_write_callbackN(struct usb_xfer *, usb_error_t, uint8_t); 193 194 /* Indexed by LOGICAL port number (subunit), so two-port device uses 0 & 1 */ 195 static usb_callback_t *umcs7840_rw_callbacks[UMCS7840_MAX_PORTS][UMCS7840_N_TRANSFERS] = { 196 {&umcs7840_read_callback1, &umcs7840_write_callback1}, 197 {&umcs7840_read_callback2, &umcs7840_write_callback2}, 198 {&umcs7840_read_callback3, &umcs7840_write_callback3}, 199 {&umcs7840_read_callback4, &umcs7840_write_callback4}, 200 }; 201 202 static const struct usb_config umcs7840_bulk_config_data[UMCS7840_N_TRANSFERS] = { 203 [UMCS7840_BULK_RD_EP] = { 204 .type = UE_BULK, 205 .endpoint = 0x01, 206 .direction = UE_DIR_IN, 207 .flags = {.pipe_bof = 1,.short_xfer_ok = 1,}, 208 .bufsize = 0, /* use wMaxPacketSize */ 209 .callback = &umcs7840_read_callback1, 210 .if_index = 0, 211 }, 212 213 [UMCS7840_BULK_WR_EP] = { 214 .type = UE_BULK, 215 .endpoint = 0x02, 216 .direction = UE_DIR_OUT, 217 .flags = {.pipe_bof = 1,.short_xfer_ok = 1,}, 218 .bufsize = 0, /* use wMaxPacketSize */ 219 .callback = &umcs7840_write_callback1, 220 .if_index = 0, 221 }, 222 }; 223 224 static const struct usb_config umcs7840_intr_config_data[1] = { 225 [0] = { 226 .type = UE_INTERRUPT, 227 .endpoint = 0x09, 228 .direction = UE_DIR_IN, 229 .flags = {.pipe_bof = 1,.short_xfer_ok = 1,}, 230 .bufsize = 0, /* use wMaxPacketSize */ 231 .callback = &umcs7840_intr_callback, 232 .if_index = 0, 233 }, 234 }; 235 236 static struct ucom_callback umcs7840_callback = { 237 .ucom_cfg_get_status = &umcs7840_cfg_get_status, 238 239 .ucom_cfg_set_dtr = &umcs7840_cfg_set_dtr, 240 .ucom_cfg_set_rts = &umcs7840_cfg_set_rts, 241 .ucom_cfg_set_break = &umcs7840_cfg_set_break, 242 243 .ucom_cfg_param = &umcs7840_cfg_param, 244 .ucom_cfg_open = &umcs7840_cfg_open, 245 .ucom_cfg_close = &umcs7840_cfg_close, 246 247 .ucom_pre_param = &umcs7840_pre_param, 248 249 .ucom_start_read = &umcs7840_start_read, 250 .ucom_stop_read = &umcs7840_stop_read, 251 252 .ucom_start_write = &umcs7840_start_write, 253 .ucom_stop_write = &umcs7840_stop_write, 254 255 .ucom_poll = &umcs7840_poll, 256 .ucom_free = &umcs7840_free, 257 }; 258 259 static const STRUCT_USB_HOST_ID umcs7840_devs[] = { 260 {USB_VPI(USB_VENDOR_MOSCHIP, USB_PRODUCT_MOSCHIP_MCS7820, 0)}, 261 {USB_VPI(USB_VENDOR_MOSCHIP, USB_PRODUCT_MOSCHIP_MCS7840, 0)}, 262 }; 263 264 static device_method_t umcs7840_methods[] = { 265 DEVMETHOD(device_probe, umcs7840_probe), 266 DEVMETHOD(device_attach, umcs7840_attach), 267 DEVMETHOD(device_detach, umcs7840_detach), 268 DEVMETHOD_END 269 }; 270 271 static devclass_t umcs7840_devclass; 272 273 static driver_t umcs7840_driver = { 274 .name = "umcs7840", 275 .methods = umcs7840_methods, 276 .size = sizeof(struct umcs7840_softc), 277 }; 278 279 DRIVER_MODULE(umcs7840, uhub, umcs7840_driver, umcs7840_devclass, 0, 0); 280 MODULE_DEPEND(umcs7840, ucom, 1, 1, 1); 281 MODULE_DEPEND(umcs7840, usb, 1, 1, 1); 282 MODULE_VERSION(umcs7840, UMCS7840_MODVER); 283 USB_PNP_HOST_INFO(umcs7840_devs); 284 285 static int 286 umcs7840_probe(device_t dev) 287 { 288 struct usb_attach_arg *uaa = device_get_ivars(dev); 289 290 if (uaa->usb_mode != USB_MODE_HOST) 291 return (ENXIO); 292 if (uaa->info.bConfigIndex != MCS7840_CONFIG_INDEX) 293 return (ENXIO); 294 if (uaa->info.bIfaceIndex != MCS7840_IFACE_INDEX) 295 return (ENXIO); 296 return (usbd_lookup_id_by_uaa(umcs7840_devs, sizeof(umcs7840_devs), uaa)); 297 } 298 299 static int 300 umcs7840_attach(device_t dev) 301 { 302 struct usb_config umcs7840_config_tmp[UMCS7840_N_TRANSFERS]; 303 struct usb_attach_arg *uaa = device_get_ivars(dev); 304 struct umcs7840_softc *sc = device_get_softc(dev); 305 306 uint8_t iface_index = MCS7840_IFACE_INDEX; 307 int error; 308 int subunit; 309 int n; 310 uint8_t data; 311 312 for (n = 0; n < UMCS7840_N_TRANSFERS; ++n) 313 umcs7840_config_tmp[n] = umcs7840_bulk_config_data[n]; 314 315 device_set_usb_desc(dev); 316 mtx_init(&sc->sc_mtx, "umcs7840", NULL, MTX_DEF); 317 ucom_ref(&sc->sc_super_ucom); 318 319 sc->sc_dev = dev; 320 sc->sc_udev = uaa->device; 321 322 /* 323 * Get number of ports 324 * Documentation (full datasheet) says, that number of ports is 325 * set as MCS7840_DEV_MODE_SELECT24S bit in MODE R/Only 326 * register. But vendor driver uses these undocumented 327 * register & bit. 328 * 329 * Experiments show, that MODE register can have `0' 330 * (4 ports) bit on 2-port device, so use vendor driver's way. 331 * 332 * Also, see notes in header file for these constants. 333 */ 334 umcs7840_get_reg_sync(sc, MCS7840_DEV_REG_GPIO, &data); 335 if (data & MCS7840_DEV_GPIO_4PORTS) { 336 sc->sc_numports = 4; 337 /* Store physical port numbers in sc_portno */ 338 sc->sc_ucom[0].sc_portno = 0; 339 sc->sc_ucom[1].sc_portno = 1; 340 sc->sc_ucom[2].sc_portno = 2; 341 sc->sc_ucom[3].sc_portno = 3; 342 } else { 343 sc->sc_numports = 2; 344 /* Store physical port numbers in sc_portno */ 345 sc->sc_ucom[0].sc_portno = 0; 346 sc->sc_ucom[1].sc_portno = 2; /* '1' is skipped */ 347 } 348 device_printf(dev, "Chip mcs%04x, found %d active ports\n", uaa->info.idProduct, sc->sc_numports); 349 if (!umcs7840_get_reg_sync(sc, MCS7840_DEV_REG_MODE, &data)) { 350 device_printf(dev, "On-die confguration: RST: active %s, HRD: %s, PLL: %s, POR: %s, Ports: %s, EEPROM write %s, IrDA is %savailable\n", 351 (data & MCS7840_DEV_MODE_RESET) ? "low" : "high", 352 (data & MCS7840_DEV_MODE_SER_PRSNT) ? "yes" : "no", 353 (data & MCS7840_DEV_MODE_PLLBYPASS) ? "bypassed" : "avail", 354 (data & MCS7840_DEV_MODE_PORBYPASS) ? "bypassed" : "avail", 355 (data & MCS7840_DEV_MODE_SELECT24S) ? "2" : "4", 356 (data & MCS7840_DEV_MODE_EEPROMWR) ? "enabled" : "disabled", 357 (data & MCS7840_DEV_MODE_IRDA) ? "" : "not "); 358 } 359 /* Setup all transfers */ 360 for (subunit = 0; subunit < sc->sc_numports; ++subunit) { 361 for (n = 0; n < UMCS7840_N_TRANSFERS; ++n) { 362 /* Set endpoint address */ 363 umcs7840_config_tmp[n].endpoint = umcs7840_bulk_config_data[n].endpoint + 2 * sc->sc_ucom[subunit].sc_portno; 364 umcs7840_config_tmp[n].callback = umcs7840_rw_callbacks[subunit][n]; 365 } 366 error = usbd_transfer_setup(uaa->device, 367 &iface_index, sc->sc_ports[sc->sc_ucom[subunit].sc_portno].sc_xfer, umcs7840_config_tmp, 368 UMCS7840_N_TRANSFERS, sc, &sc->sc_mtx); 369 if (error) { 370 device_printf(dev, "allocating USB transfers failed for subunit %d of %d\n", 371 subunit + 1, sc->sc_numports); 372 goto detach; 373 } 374 } 375 error = usbd_transfer_setup(uaa->device, 376 &iface_index, &sc->sc_intr_xfer, umcs7840_intr_config_data, 377 1, sc, &sc->sc_mtx); 378 if (error) { 379 device_printf(dev, "allocating USB transfers failed for interrupt\n"); 380 goto detach; 381 } 382 /* clear stall at first run */ 383 mtx_lock(&sc->sc_mtx); 384 for (subunit = 0; subunit < sc->sc_numports; ++subunit) { 385 usbd_xfer_set_stall(sc->sc_ports[sc->sc_ucom[subunit].sc_portno].sc_xfer[UMCS7840_BULK_RD_EP]); 386 usbd_xfer_set_stall(sc->sc_ports[sc->sc_ucom[subunit].sc_portno].sc_xfer[UMCS7840_BULK_WR_EP]); 387 } 388 mtx_unlock(&sc->sc_mtx); 389 390 error = ucom_attach(&sc->sc_super_ucom, sc->sc_ucom, sc->sc_numports, sc, 391 &umcs7840_callback, &sc->sc_mtx); 392 if (error) 393 goto detach; 394 395 ucom_set_pnpinfo_usb(&sc->sc_super_ucom, dev); 396 397 return (0); 398 399 detach: 400 umcs7840_detach(dev); 401 return (ENXIO); 402 } 403 404 static int 405 umcs7840_detach(device_t dev) 406 { 407 struct umcs7840_softc *sc = device_get_softc(dev); 408 int subunit; 409 410 ucom_detach(&sc->sc_super_ucom, sc->sc_ucom); 411 412 for (subunit = 0; subunit < sc->sc_numports; ++subunit) 413 usbd_transfer_unsetup(sc->sc_ports[sc->sc_ucom[subunit].sc_portno].sc_xfer, UMCS7840_N_TRANSFERS); 414 usbd_transfer_unsetup(&sc->sc_intr_xfer, 1); 415 416 device_claim_softc(dev); 417 418 umcs7840_free_softc(sc); 419 420 return (0); 421 } 422 423 UCOM_UNLOAD_DRAIN(umcs7840); 424 425 static void 426 umcs7840_free_softc(struct umcs7840_softc *sc) 427 { 428 if (ucom_unref(&sc->sc_super_ucom)) { 429 mtx_destroy(&sc->sc_mtx); 430 device_free_softc(sc); 431 } 432 } 433 434 static void 435 umcs7840_free(struct ucom_softc *ucom) 436 { 437 umcs7840_free_softc(ucom->sc_parent); 438 } 439 440 static void 441 umcs7840_cfg_open(struct ucom_softc *ucom) 442 { 443 struct umcs7840_softc *sc = ucom->sc_parent; 444 uint16_t pn = ucom->sc_portno; 445 uint8_t data; 446 447 /* If it very first open, finish global configuration */ 448 if (!sc->sc_driver_done) { 449 /* 450 * USB enumeration is finished, pass internal memory to FIFOs 451 * If it is done in the end of "attach", kernel panics. 452 */ 453 if (umcs7840_get_reg_sync(sc, MCS7840_DEV_REG_CONTROL1, &data)) 454 return; 455 data |= MCS7840_DEV_CONTROL1_DRIVER_DONE; 456 if (umcs7840_set_reg_sync(sc, MCS7840_DEV_REG_CONTROL1, data)) 457 return; 458 sc->sc_driver_done = 1; 459 } 460 /* Toggle reset bit on-off */ 461 if (umcs7840_get_reg_sync(sc, umcs7840_port_registers[pn].reg_sp, &data)) 462 return; 463 data |= MCS7840_DEV_SPx_UART_RESET; 464 if (umcs7840_set_reg_sync(sc, umcs7840_port_registers[pn].reg_sp, data)) 465 return; 466 data &= ~MCS7840_DEV_SPx_UART_RESET; 467 if (umcs7840_set_reg_sync(sc, umcs7840_port_registers[pn].reg_sp, data)) 468 return; 469 470 /* Set RS-232 mode */ 471 if (umcs7840_set_UART_reg_sync(sc, pn, MCS7840_UART_REG_SCRATCHPAD, MCS7840_UART_SCRATCHPAD_RS232)) 472 return; 473 474 /* Disable RX on time of initialization */ 475 if (umcs7840_get_reg_sync(sc, umcs7840_port_registers[pn].reg_control, &data)) 476 return; 477 data |= MCS7840_DEV_CONTROLx_RX_DISABLE; 478 if (umcs7840_set_reg_sync(sc, umcs7840_port_registers[pn].reg_control, data)) 479 return; 480 481 /* Disable all interrupts */ 482 if (umcs7840_set_UART_reg_sync(sc, pn, MCS7840_UART_REG_IER, 0)) 483 return; 484 485 /* Reset FIFO -- documented */ 486 if (umcs7840_set_UART_reg_sync(sc, pn, MCS7840_UART_REG_FCR, 0)) 487 return; 488 if (umcs7840_set_UART_reg_sync(sc, pn, MCS7840_UART_REG_FCR, 489 MCS7840_UART_FCR_ENABLE | MCS7840_UART_FCR_FLUSHRHR | 490 MCS7840_UART_FCR_FLUSHTHR | MCS7840_UART_FCR_RTL_1_14)) 491 return; 492 493 /* Set 8 bit, no parity, 1 stop bit -- documented */ 494 sc->sc_ports[pn].sc_lcr = MCS7840_UART_LCR_DATALEN8 | MCS7840_UART_LCR_STOPB1; 495 if (umcs7840_set_UART_reg_sync(sc, pn, MCS7840_UART_REG_LCR, sc->sc_ports[pn].sc_lcr)) 496 return; 497 498 /* 499 * Enable DTR/RTS on modem control, enable modem interrupts -- 500 * documented 501 */ 502 sc->sc_ports[pn].sc_mcr = MCS7840_UART_MCR_DTR | MCS7840_UART_MCR_RTS | MCS7840_UART_MCR_IE; 503 if (umcs7840_set_UART_reg_sync(sc, pn, MCS7840_UART_REG_MCR, sc->sc_ports[pn].sc_mcr)) 504 return; 505 506 /* Clearing Bulkin and Bulkout FIFO */ 507 if (umcs7840_get_reg_sync(sc, umcs7840_port_registers[pn].reg_sp, &data)) 508 return; 509 data |= MCS7840_DEV_SPx_RESET_OUT_FIFO | MCS7840_DEV_SPx_RESET_IN_FIFO; 510 if (umcs7840_set_reg_sync(sc, umcs7840_port_registers[pn].reg_sp, data)) 511 return; 512 data &= ~(MCS7840_DEV_SPx_RESET_OUT_FIFO | MCS7840_DEV_SPx_RESET_IN_FIFO); 513 if (umcs7840_set_reg_sync(sc, umcs7840_port_registers[pn].reg_sp, data)) 514 return; 515 516 /* Set speed 9600 */ 517 if (umcs7840_set_baudrate(sc, pn, 9600)) 518 return; 519 520 521 /* Finally enable all interrupts -- documented */ 522 /* 523 * Copied from vendor driver, I don't know why we should read LCR 524 * here 525 */ 526 if (umcs7840_get_UART_reg_sync(sc, pn, MCS7840_UART_REG_LCR, &sc->sc_ports[pn].sc_lcr)) 527 return; 528 if (umcs7840_set_UART_reg_sync(sc, pn, MCS7840_UART_REG_IER, 529 MCS7840_UART_IER_RXSTAT | MCS7840_UART_IER_MODEM)) 530 return; 531 532 /* Enable RX */ 533 if (umcs7840_get_reg_sync(sc, umcs7840_port_registers[pn].reg_control, &data)) 534 return; 535 data &= ~MCS7840_DEV_CONTROLx_RX_DISABLE; 536 if (umcs7840_set_reg_sync(sc, umcs7840_port_registers[pn].reg_control, data)) 537 return; 538 539 DPRINTF("Port %d has been opened\n", pn); 540 } 541 542 static void 543 umcs7840_cfg_close(struct ucom_softc *ucom) 544 { 545 struct umcs7840_softc *sc = ucom->sc_parent; 546 uint16_t pn = ucom->sc_portno; 547 uint8_t data; 548 549 umcs7840_stop_read(ucom); 550 umcs7840_stop_write(ucom); 551 552 umcs7840_set_UART_reg_sync(sc, pn, MCS7840_UART_REG_MCR, 0); 553 umcs7840_set_UART_reg_sync(sc, pn, MCS7840_UART_REG_IER, 0); 554 555 /* Disable RX */ 556 if (umcs7840_get_reg_sync(sc, umcs7840_port_registers[pn].reg_control, &data)) 557 return; 558 data |= MCS7840_DEV_CONTROLx_RX_DISABLE; 559 if (umcs7840_set_reg_sync(sc, umcs7840_port_registers[pn].reg_control, data)) 560 return; 561 DPRINTF("Port %d has been closed\n", pn); 562 } 563 564 static void 565 umcs7840_cfg_set_dtr(struct ucom_softc *ucom, uint8_t onoff) 566 { 567 struct umcs7840_softc *sc = ucom->sc_parent; 568 uint8_t pn = ucom->sc_portno; 569 570 if (onoff) 571 sc->sc_ports[pn].sc_mcr |= MCS7840_UART_MCR_DTR; 572 else 573 sc->sc_ports[pn].sc_mcr &= ~MCS7840_UART_MCR_DTR; 574 575 umcs7840_set_UART_reg_sync(sc, pn, MCS7840_UART_REG_MCR, sc->sc_ports[pn].sc_mcr); 576 DPRINTF("Port %d DTR set to: %s\n", pn, onoff ? "on" : "off"); 577 } 578 579 static void 580 umcs7840_cfg_set_rts(struct ucom_softc *ucom, uint8_t onoff) 581 { 582 struct umcs7840_softc *sc = ucom->sc_parent; 583 uint8_t pn = ucom->sc_portno; 584 585 if (onoff) 586 sc->sc_ports[pn].sc_mcr |= MCS7840_UART_MCR_RTS; 587 else 588 sc->sc_ports[pn].sc_mcr &= ~MCS7840_UART_MCR_RTS; 589 590 umcs7840_set_UART_reg_sync(sc, pn, MCS7840_UART_REG_MCR, sc->sc_ports[pn].sc_mcr); 591 DPRINTF("Port %d RTS set to: %s\n", pn, onoff ? "on" : "off"); 592 } 593 594 static void 595 umcs7840_cfg_set_break(struct ucom_softc *ucom, uint8_t onoff) 596 { 597 struct umcs7840_softc *sc = ucom->sc_parent; 598 uint8_t pn = ucom->sc_portno; 599 600 if (onoff) 601 sc->sc_ports[pn].sc_lcr |= MCS7840_UART_LCR_BREAK; 602 else 603 sc->sc_ports[pn].sc_lcr &= ~MCS7840_UART_LCR_BREAK; 604 605 umcs7840_set_UART_reg_sync(sc, pn, MCS7840_UART_REG_LCR, sc->sc_ports[pn].sc_lcr); 606 DPRINTF("Port %d BREAK set to: %s\n", pn, onoff ? "on" : "off"); 607 } 608 609 610 static void 611 umcs7840_cfg_param(struct ucom_softc *ucom, struct termios *t) 612 { 613 struct umcs7840_softc *sc = ucom->sc_parent; 614 uint8_t pn = ucom->sc_portno; 615 uint8_t lcr = sc->sc_ports[pn].sc_lcr; 616 uint8_t mcr = sc->sc_ports[pn].sc_mcr; 617 618 DPRINTF("Port %d config:\n", pn); 619 if (t->c_cflag & CSTOPB) { 620 DPRINTF(" 2 stop bits\n"); 621 lcr |= MCS7840_UART_LCR_STOPB2; 622 } else { 623 lcr |= MCS7840_UART_LCR_STOPB1; 624 DPRINTF(" 1 stop bit\n"); 625 } 626 627 lcr &= ~MCS7840_UART_LCR_PARITYMASK; 628 if (t->c_cflag & PARENB) { 629 lcr |= MCS7840_UART_LCR_PARITYON; 630 if (t->c_cflag & PARODD) { 631 lcr = MCS7840_UART_LCR_PARITYODD; 632 DPRINTF(" parity on - odd\n"); 633 } else { 634 lcr = MCS7840_UART_LCR_PARITYEVEN; 635 DPRINTF(" parity on - even\n"); 636 } 637 } else { 638 lcr &= ~MCS7840_UART_LCR_PARITYON; 639 DPRINTF(" parity off\n"); 640 } 641 642 lcr &= ~MCS7840_UART_LCR_DATALENMASK; 643 switch (t->c_cflag & CSIZE) { 644 case CS5: 645 lcr |= MCS7840_UART_LCR_DATALEN5; 646 DPRINTF(" 5 bit\n"); 647 break; 648 case CS6: 649 lcr |= MCS7840_UART_LCR_DATALEN6; 650 DPRINTF(" 6 bit\n"); 651 break; 652 case CS7: 653 lcr |= MCS7840_UART_LCR_DATALEN7; 654 DPRINTF(" 7 bit\n"); 655 break; 656 case CS8: 657 lcr |= MCS7840_UART_LCR_DATALEN8; 658 DPRINTF(" 8 bit\n"); 659 break; 660 } 661 662 if (t->c_cflag & CRTSCTS) { 663 mcr |= MCS7840_UART_MCR_CTSRTS; 664 DPRINTF(" CTS/RTS\n"); 665 } else 666 mcr &= ~MCS7840_UART_MCR_CTSRTS; 667 668 if (t->c_cflag & (CDTR_IFLOW | CDSR_OFLOW)) { 669 mcr |= MCS7840_UART_MCR_DTRDSR; 670 DPRINTF(" DTR/DSR\n"); 671 } else 672 mcr &= ~MCS7840_UART_MCR_DTRDSR; 673 674 sc->sc_ports[pn].sc_lcr = lcr; 675 umcs7840_set_UART_reg_sync(sc, pn, MCS7840_UART_REG_LCR, sc->sc_ports[pn].sc_lcr); 676 DPRINTF("Port %d LCR=%02x\n", pn, sc->sc_ports[pn].sc_lcr); 677 678 sc->sc_ports[pn].sc_mcr = mcr; 679 umcs7840_set_UART_reg_sync(sc, pn, MCS7840_UART_REG_MCR, sc->sc_ports[pn].sc_mcr); 680 DPRINTF("Port %d MCR=%02x\n", pn, sc->sc_ports[pn].sc_mcr); 681 682 umcs7840_set_baudrate(sc, pn, t->c_ospeed); 683 } 684 685 686 static int 687 umcs7840_pre_param(struct ucom_softc *ucom, struct termios *t) 688 { 689 uint8_t clk; 690 uint16_t divisor; 691 692 if (umcs7840_calc_baudrate(t->c_ospeed, &divisor, &clk) || !divisor) 693 return (EINVAL); 694 return (0); 695 } 696 697 static void 698 umcs7840_start_read(struct ucom_softc *ucom) 699 { 700 struct umcs7840_softc *sc = ucom->sc_parent; 701 uint8_t pn = ucom->sc_portno; 702 703 /* Start interrupt transfer */ 704 usbd_transfer_start(sc->sc_intr_xfer); 705 706 /* Start read transfer */ 707 usbd_transfer_start(sc->sc_ports[pn].sc_xfer[UMCS7840_BULK_RD_EP]); 708 } 709 710 static void 711 umcs7840_stop_read(struct ucom_softc *ucom) 712 { 713 struct umcs7840_softc *sc = ucom->sc_parent; 714 uint8_t pn = ucom->sc_portno; 715 716 /* Stop read transfer */ 717 usbd_transfer_stop(sc->sc_ports[pn].sc_xfer[UMCS7840_BULK_RD_EP]); 718 } 719 720 static void 721 umcs7840_start_write(struct ucom_softc *ucom) 722 { 723 struct umcs7840_softc *sc = ucom->sc_parent; 724 uint8_t pn = ucom->sc_portno; 725 726 /* Start interrupt transfer */ 727 usbd_transfer_start(sc->sc_intr_xfer); 728 729 /* Start write transfer */ 730 usbd_transfer_start(sc->sc_ports[pn].sc_xfer[UMCS7840_BULK_WR_EP]); 731 } 732 733 static void 734 umcs7840_stop_write(struct ucom_softc *ucom) 735 { 736 struct umcs7840_softc *sc = ucom->sc_parent; 737 uint8_t pn = ucom->sc_portno; 738 739 /* Stop write transfer */ 740 usbd_transfer_stop(sc->sc_ports[pn].sc_xfer[UMCS7840_BULK_WR_EP]); 741 } 742 743 static void 744 umcs7840_cfg_get_status(struct ucom_softc *ucom, uint8_t *lsr, uint8_t *msr) 745 { 746 struct umcs7840_softc *sc = ucom->sc_parent; 747 uint8_t pn = ucom->sc_portno; 748 uint8_t hw_msr = 0; /* local modem status register */ 749 750 /* 751 * Read status registers. MSR bits need translation from ns16550 to 752 * SER_* values. LSR bits are ns16550 in hardware and ucom. 753 */ 754 umcs7840_get_UART_reg_sync(sc, pn, MCS7840_UART_REG_LSR, lsr); 755 umcs7840_get_UART_reg_sync(sc, pn, MCS7840_UART_REG_MSR, &hw_msr); 756 757 if (hw_msr & MCS7840_UART_MSR_NEGCTS) 758 *msr |= SER_CTS; 759 760 if (hw_msr & MCS7840_UART_MSR_NEGDCD) 761 *msr |= SER_DCD; 762 763 if (hw_msr & MCS7840_UART_MSR_NEGRI) 764 *msr |= SER_RI; 765 766 if (hw_msr & MCS7840_UART_MSR_NEGDSR) 767 *msr |= SER_DSR; 768 769 DPRINTF("Port %d status: LSR=%02x MSR=%02x\n", ucom->sc_portno, *lsr, *msr); 770 } 771 772 static void 773 umcs7840_intr_callback(struct usb_xfer *xfer, usb_error_t error) 774 { 775 struct umcs7840_softc *sc = usbd_xfer_softc(xfer); 776 struct usb_page_cache *pc; 777 uint8_t buf[13]; 778 int actlen; 779 int subunit; 780 781 usbd_xfer_status(xfer, &actlen, NULL, NULL, NULL); 782 783 switch (USB_GET_STATE(xfer)) { 784 case USB_ST_TRANSFERRED: 785 if (actlen == 5 || actlen == 13) { 786 pc = usbd_xfer_get_frame(xfer, 0); 787 usbd_copy_out(pc, 0, buf, actlen); 788 /* Check status of all ports */ 789 for (subunit = 0; subunit < sc->sc_numports; ++subunit) { 790 uint8_t pn = sc->sc_ucom[subunit].sc_portno; 791 792 if (buf[pn] & MCS7840_UART_ISR_NOPENDING) 793 continue; 794 DPRINTF("Port %d has pending interrupt: %02x (FIFO: %02x)\n", pn, buf[pn] & MCS7840_UART_ISR_INTMASK, buf[pn] & (~MCS7840_UART_ISR_INTMASK)); 795 switch (buf[pn] & MCS7840_UART_ISR_INTMASK) { 796 case MCS7840_UART_ISR_RXERR: 797 case MCS7840_UART_ISR_RXHASDATA: 798 case MCS7840_UART_ISR_RXTIMEOUT: 799 case MCS7840_UART_ISR_MSCHANGE: 800 ucom_status_change(&sc->sc_ucom[subunit]); 801 break; 802 default: 803 /* Do nothing */ 804 break; 805 } 806 } 807 } else 808 device_printf(sc->sc_dev, "Invalid interrupt data length %d", actlen); 809 /* FALLTHROUGH */ 810 case USB_ST_SETUP: 811 tr_setup: 812 usbd_xfer_set_frame_len(xfer, 0, usbd_xfer_max_len(xfer)); 813 usbd_transfer_submit(xfer); 814 return; 815 816 default: /* Error */ 817 if (error != USB_ERR_CANCELLED) { 818 /* try to clear stall first */ 819 usbd_xfer_set_stall(xfer); 820 goto tr_setup; 821 } 822 return; 823 } 824 } 825 826 static void 827 umcs7840_read_callback1(struct usb_xfer *xfer, usb_error_t error) 828 { 829 umcs7840_read_callbackN(xfer, error, 0); 830 } 831 832 static void 833 umcs7840_read_callback2(struct usb_xfer *xfer, usb_error_t error) 834 { 835 umcs7840_read_callbackN(xfer, error, 1); 836 } 837 static void 838 umcs7840_read_callback3(struct usb_xfer *xfer, usb_error_t error) 839 { 840 umcs7840_read_callbackN(xfer, error, 2); 841 } 842 843 static void 844 umcs7840_read_callback4(struct usb_xfer *xfer, usb_error_t error) 845 { 846 umcs7840_read_callbackN(xfer, error, 3); 847 } 848 849 static void 850 umcs7840_read_callbackN(struct usb_xfer *xfer, usb_error_t error, uint8_t subunit) 851 { 852 struct umcs7840_softc *sc = usbd_xfer_softc(xfer); 853 struct ucom_softc *ucom = &sc->sc_ucom[subunit]; 854 struct usb_page_cache *pc; 855 int actlen; 856 857 usbd_xfer_status(xfer, &actlen, NULL, NULL, NULL); 858 859 DPRINTF("Port %d read, state = %d, data length = %d\n", ucom->sc_portno, USB_GET_STATE(xfer), actlen); 860 861 switch (USB_GET_STATE(xfer)) { 862 case USB_ST_TRANSFERRED: 863 pc = usbd_xfer_get_frame(xfer, 0); 864 ucom_put_data(ucom, pc, 0, actlen); 865 /* FALLTHROUGH */ 866 case USB_ST_SETUP: 867 tr_setup: 868 usbd_xfer_set_frame_len(xfer, 0, usbd_xfer_max_len(xfer)); 869 usbd_transfer_submit(xfer); 870 return; 871 872 default: /* Error */ 873 if (error != USB_ERR_CANCELLED) { 874 /* try to clear stall first */ 875 usbd_xfer_set_stall(xfer); 876 goto tr_setup; 877 } 878 return; 879 } 880 } 881 882 static void 883 umcs7840_write_callback1(struct usb_xfer *xfer, usb_error_t error) 884 { 885 umcs7840_write_callbackN(xfer, error, 0); 886 } 887 888 static void 889 umcs7840_write_callback2(struct usb_xfer *xfer, usb_error_t error) 890 { 891 umcs7840_write_callbackN(xfer, error, 1); 892 } 893 894 static void 895 umcs7840_write_callback3(struct usb_xfer *xfer, usb_error_t error) 896 { 897 umcs7840_write_callbackN(xfer, error, 2); 898 } 899 900 static void 901 umcs7840_write_callback4(struct usb_xfer *xfer, usb_error_t error) 902 { 903 umcs7840_write_callbackN(xfer, error, 3); 904 } 905 906 static void 907 umcs7840_write_callbackN(struct usb_xfer *xfer, usb_error_t error, uint8_t subunit) 908 { 909 struct umcs7840_softc *sc = usbd_xfer_softc(xfer); 910 struct ucom_softc *ucom = &sc->sc_ucom[subunit]; 911 struct usb_page_cache *pc; 912 uint32_t actlen; 913 914 DPRINTF("Port %d write, state = %d\n", ucom->sc_portno, USB_GET_STATE(xfer)); 915 916 switch (USB_GET_STATE(xfer)) { 917 case USB_ST_SETUP: 918 case USB_ST_TRANSFERRED: 919 tr_setup: 920 pc = usbd_xfer_get_frame(xfer, 0); 921 if (ucom_get_data(ucom, pc, 0, usbd_xfer_max_len(xfer), &actlen)) { 922 DPRINTF("Port %d write, has %d bytes\n", ucom->sc_portno, actlen); 923 usbd_xfer_set_frame_len(xfer, 0, actlen); 924 usbd_transfer_submit(xfer); 925 } 926 return; 927 928 default: /* Error */ 929 if (error != USB_ERR_CANCELLED) { 930 /* try to clear stall first */ 931 usbd_xfer_set_stall(xfer); 932 goto tr_setup; 933 } 934 return; 935 } 936 } 937 938 static void 939 umcs7840_poll(struct ucom_softc *ucom) 940 { 941 struct umcs7840_softc *sc = ucom->sc_parent; 942 943 DPRINTF("Port %d poll\n", ucom->sc_portno); 944 usbd_transfer_poll(sc->sc_ports[ucom->sc_portno].sc_xfer, UMCS7840_N_TRANSFERS); 945 usbd_transfer_poll(&sc->sc_intr_xfer, 1); 946 } 947 948 static usb_error_t 949 umcs7840_get_reg_sync(struct umcs7840_softc *sc, uint8_t reg, uint8_t *data) 950 { 951 struct usb_device_request req; 952 usb_error_t err; 953 uint16_t len; 954 955 req.bmRequestType = UT_READ_VENDOR_DEVICE; 956 req.bRequest = MCS7840_RDREQ; 957 USETW(req.wValue, 0); 958 USETW(req.wIndex, reg); 959 USETW(req.wLength, UMCS7840_READ_LENGTH); 960 961 err = usbd_do_request_proc(sc->sc_udev, &sc->sc_super_ucom.sc_tq, &req, (void *)data, 0, &len, UMCS7840_CTRL_TIMEOUT); 962 if (err == USB_ERR_NORMAL_COMPLETION && len != 1) { 963 device_printf(sc->sc_dev, "Reading register %d failed: invalid length %d\n", reg, len); 964 return (USB_ERR_INVAL); 965 } else if (err) 966 device_printf(sc->sc_dev, "Reading register %d failed: %s\n", reg, usbd_errstr(err)); 967 return (err); 968 } 969 970 static usb_error_t 971 umcs7840_set_reg_sync(struct umcs7840_softc *sc, uint8_t reg, uint8_t data) 972 { 973 struct usb_device_request req; 974 usb_error_t err; 975 976 req.bmRequestType = UT_WRITE_VENDOR_DEVICE; 977 req.bRequest = MCS7840_WRREQ; 978 USETW(req.wValue, data); 979 USETW(req.wIndex, reg); 980 USETW(req.wLength, 0); 981 982 err = usbd_do_request_proc(sc->sc_udev, &sc->sc_super_ucom.sc_tq, &req, NULL, 0, NULL, UMCS7840_CTRL_TIMEOUT); 983 if (err) 984 device_printf(sc->sc_dev, "Writing register %d failed: %s\n", reg, usbd_errstr(err)); 985 986 return (err); 987 } 988 989 static usb_error_t 990 umcs7840_get_UART_reg_sync(struct umcs7840_softc *sc, uint8_t portno, uint8_t reg, uint8_t *data) 991 { 992 struct usb_device_request req; 993 uint16_t wVal; 994 usb_error_t err; 995 uint16_t len; 996 997 /* portno is port number */ 998 wVal = ((uint16_t)(portno + 1)) << 8; 999 1000 req.bmRequestType = UT_READ_VENDOR_DEVICE; 1001 req.bRequest = MCS7840_RDREQ; 1002 USETW(req.wValue, wVal); 1003 USETW(req.wIndex, reg); 1004 USETW(req.wLength, UMCS7840_READ_LENGTH); 1005 1006 err = usbd_do_request_proc(sc->sc_udev, &sc->sc_super_ucom.sc_tq, &req, (void *)data, 0, &len, UMCS7840_CTRL_TIMEOUT); 1007 if (err == USB_ERR_NORMAL_COMPLETION && len != 1) { 1008 device_printf(sc->sc_dev, "Reading UART%d register %d failed: invalid length %d\n", portno, reg, len); 1009 return (USB_ERR_INVAL); 1010 } else if (err) 1011 device_printf(sc->sc_dev, "Reading UART%d register %d failed: %s\n", portno, reg, usbd_errstr(err)); 1012 return (err); 1013 } 1014 1015 static usb_error_t 1016 umcs7840_set_UART_reg_sync(struct umcs7840_softc *sc, uint8_t portno, uint8_t reg, uint8_t data) 1017 { 1018 struct usb_device_request req; 1019 usb_error_t err; 1020 uint16_t wVal; 1021 1022 /* portno is port number */ 1023 wVal = ((uint16_t)(portno + 1)) << 8 | data; 1024 1025 req.bmRequestType = UT_WRITE_VENDOR_DEVICE; 1026 req.bRequest = MCS7840_WRREQ; 1027 USETW(req.wValue, wVal); 1028 USETW(req.wIndex, reg); 1029 USETW(req.wLength, 0); 1030 1031 err = usbd_do_request_proc(sc->sc_udev, &sc->sc_super_ucom.sc_tq, &req, NULL, 0, NULL, UMCS7840_CTRL_TIMEOUT); 1032 if (err) 1033 device_printf(sc->sc_dev, "Writing UART%d register %d failed: %s\n", portno, reg, usbd_errstr(err)); 1034 return (err); 1035 } 1036 1037 static usb_error_t 1038 umcs7840_set_baudrate(struct umcs7840_softc *sc, uint8_t portno, uint32_t rate) 1039 { 1040 usb_error_t err; 1041 uint16_t divisor; 1042 uint8_t clk; 1043 uint8_t data; 1044 1045 if (umcs7840_calc_baudrate(rate, &divisor, &clk)) { 1046 DPRINTF("Port %d bad speed: %d\n", portno, rate); 1047 return (-1); 1048 } 1049 if (divisor == 0 || (clk & MCS7840_DEV_SPx_CLOCK_MASK) != clk) { 1050 DPRINTF("Port %d bad speed calculation: %d\n", portno, rate); 1051 return (-1); 1052 } 1053 DPRINTF("Port %d set speed: %d (%02x / %d)\n", portno, rate, clk, divisor); 1054 1055 /* Set clock source for standard BAUD frequences */ 1056 err = umcs7840_get_reg_sync(sc, umcs7840_port_registers[portno].reg_sp, &data); 1057 if (err) 1058 return (err); 1059 data &= MCS7840_DEV_SPx_CLOCK_MASK; 1060 data |= clk; 1061 err = umcs7840_set_reg_sync(sc, umcs7840_port_registers[portno].reg_sp, data); 1062 if (err) 1063 return (err); 1064 1065 /* Set divider */ 1066 sc->sc_ports[portno].sc_lcr |= MCS7840_UART_LCR_DIVISORS; 1067 err = umcs7840_set_UART_reg_sync(sc, portno, MCS7840_UART_REG_LCR, sc->sc_ports[portno].sc_lcr); 1068 if (err) 1069 return (err); 1070 1071 err = umcs7840_set_UART_reg_sync(sc, portno, MCS7840_UART_REG_DLL, (uint8_t)(divisor & 0xff)); 1072 if (err) 1073 return (err); 1074 err = umcs7840_set_UART_reg_sync(sc, portno, MCS7840_UART_REG_DLM, (uint8_t)((divisor >> 8) & 0xff)); 1075 if (err) 1076 return (err); 1077 1078 /* Turn off access to DLL/DLM registers of UART */ 1079 sc->sc_ports[portno].sc_lcr &= ~MCS7840_UART_LCR_DIVISORS; 1080 err = umcs7840_set_UART_reg_sync(sc, portno, MCS7840_UART_REG_LCR, sc->sc_ports[portno].sc_lcr); 1081 if (err) 1082 return (err); 1083 return (0); 1084 } 1085 1086 /* Maximum speeds for standard frequences, when PLL is not used */ 1087 static const uint32_t umcs7840_baudrate_divisors[] = {0, 115200, 230400, 403200, 460800, 806400, 921600, 1572864, 3145728,}; 1088 static const uint8_t umcs7840_baudrate_divisors_len = nitems(umcs7840_baudrate_divisors); 1089 1090 static usb_error_t 1091 umcs7840_calc_baudrate(uint32_t rate, uint16_t *divisor, uint8_t *clk) 1092 { 1093 uint8_t i = 0; 1094 1095 if (rate > umcs7840_baudrate_divisors[umcs7840_baudrate_divisors_len - 1]) 1096 return (-1); 1097 1098 for (i = 0; i < umcs7840_baudrate_divisors_len - 1 && 1099 !(rate > umcs7840_baudrate_divisors[i] && rate <= umcs7840_baudrate_divisors[i + 1]); ++i); 1100 if (rate == 0) 1101 *divisor = 1; /* XXX */ 1102 else 1103 *divisor = umcs7840_baudrate_divisors[i + 1] / rate; 1104 /* 0x00 .. 0x70 */ 1105 *clk = i << MCS7840_DEV_SPx_CLOCK_SHIFT; 1106 return (0); 1107 } 1108