1 /*- 2 * SPDX-License-Identifier: BSD-2-Clause 3 * 4 * Copyright (c) 2008 Hans Petter Selasky. All rights reserved. 5 * 6 * Redistribution and use in source and binary forms, with or without 7 * modification, are permitted provided that the following conditions 8 * are met: 9 * 1. Redistributions of source code must retain the above copyright 10 * notice, this list of conditions and the following disclaimer. 11 * 2. Redistributions in binary form must reproduce the above copyright 12 * notice, this list of conditions and the following disclaimer in the 13 * documentation and/or other materials provided with the distribution. 14 * 15 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND 16 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 17 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 18 * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE 19 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 20 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 21 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 22 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT 23 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 24 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 25 * SUCH DAMAGE. 26 */ 27 28 #ifndef _USB_QUIRK_H_ 29 #define _USB_QUIRK_H_ 30 31 enum { 32 /* 33 * Keep in sync with usb_quirk_str in usb_quirk.c, and with 34 * share/man/man4/usb_quirk.4 35 */ 36 UQ_NONE, /* not a valid quirk */ 37 38 UQ_MATCH_VENDOR_ONLY, /* match quirk on vendor only */ 39 40 /* Various quirks */ 41 42 UQ_AUDIO_SWAP_LR, /* left and right sound channels are swapped */ 43 UQ_AU_INP_ASYNC, /* input is async despite claim of adaptive */ 44 UQ_AU_NO_FRAC, /* don't adjust for fractional samples */ 45 UQ_AU_NO_XU, /* audio device has broken extension unit */ 46 UQ_BAD_ADC, /* bad audio spec version number */ 47 UQ_BAD_AUDIO, /* device claims audio class, but isn't */ 48 UQ_BROKEN_BIDIR, /* printer has broken bidir mode */ 49 UQ_BUS_POWERED, /* device is bus powered, despite claim */ 50 UQ_HID_IGNORE, /* device should be ignored by hid class */ 51 UQ_KBD_IGNORE, /* device should be ignored by kbd class */ 52 UQ_KBD_BOOTPROTO, /* device should set the boot protocol */ 53 UQ_UMS_IGNORE, /* device should be ignored by ums class */ 54 UQ_MS_BAD_CLASS, /* doesn't identify properly */ 55 UQ_MS_LEADING_BYTE, /* mouse sends an unknown leading byte */ 56 UQ_MS_REVZ, /* mouse has Z-axis reversed */ 57 UQ_MS_VENDOR_BTN, /* mouse has buttons in vendor usage page */ 58 UQ_NO_STRINGS, /* string descriptors are broken */ 59 UQ_POWER_CLAIM, /* hub lies about power status */ 60 UQ_SPUR_BUT_UP, /* spurious mouse button up events */ 61 UQ_SWAP_UNICODE, /* has some Unicode strings swapped */ 62 UQ_CFG_INDEX_1, /* select configuration index 1 by default */ 63 UQ_CFG_INDEX_2, /* select configuration index 2 by default */ 64 UQ_CFG_INDEX_3, /* select configuration index 3 by default */ 65 UQ_CFG_INDEX_4, /* select configuration index 4 by default */ 66 UQ_CFG_INDEX_0, /* select configuration index 0 by default */ 67 UQ_ASSUME_CM_OVER_DATA, /* assume cm over data feature */ 68 UQ_IGNORE_CDC_CM, /* ignore cm descriptor */ 69 70 /* 71 * USB Mass Storage Quirks. See "storage/umass.c" for a 72 * detailed description. 73 */ 74 UQ_MSC_NO_TEST_UNIT_READY, /* send start/stop instead of TUR */ 75 UQ_MSC_NO_RS_CLEAR_UA, /* does not reset Unit Att. */ 76 UQ_MSC_NO_START_STOP, /* does not support start/stop */ 77 UQ_MSC_NO_GETMAXLUN, /* does not support get max LUN */ 78 UQ_MSC_NO_INQUIRY, /* fake generic inq response */ 79 UQ_MSC_NO_INQUIRY_EVPD, /* does not support inq EVPD */ 80 UQ_MSC_NO_PREVENT_ALLOW, /* does not support medium removal */ 81 UQ_MSC_NO_SYNC_CACHE, /* does not support sync cache */ 82 UQ_MSC_SHUTTLE_INIT, /* requires Shuttle init sequence */ 83 UQ_MSC_ALT_IFACE_1, /* switch to alternate interface 1 */ 84 UQ_MSC_FLOPPY_SPEED, /* does floppy speeds (20kb/s) */ 85 UQ_MSC_IGNORE_RESIDUE, /* gets residue wrong */ 86 UQ_MSC_WRONG_CSWSIG, /* uses wrong CSW signature */ 87 UQ_MSC_RBC_PAD_TO_12, /* pad RBC requests to 12 bytes */ 88 UQ_MSC_READ_CAP_OFFBY1, /* reports sector count, not max sec. */ 89 UQ_MSC_FORCE_SHORT_INQ, /* does not support full inq. */ 90 UQ_MSC_FORCE_WIRE_BBB, /* force BBB wire protocol */ 91 UQ_MSC_FORCE_WIRE_CBI, /* force CBI wire protocol */ 92 UQ_MSC_FORCE_WIRE_CBI_I, /* force CBI with int. wire protocol */ 93 UQ_MSC_FORCE_PROTO_SCSI, /* force SCSI command protocol */ 94 UQ_MSC_FORCE_PROTO_ATAPI, /* force ATAPI command protocol */ 95 UQ_MSC_FORCE_PROTO_UFI, /* force UFI command protocol */ 96 UQ_MSC_FORCE_PROTO_RBC, /* force RBC command protocol */ 97 UQ_MSC_IGNORE, /* device should be ignored by umass */ 98 99 /* Ejection of mass storage (driver disk) */ 100 UQ_MSC_EJECT_HUAWEI, /* ejects after Huawei USB command */ 101 UQ_MSC_EJECT_SIERRA, /* ejects after Sierra USB command */ 102 UQ_MSC_EJECT_SCSIEJECT, /* ejects after SCSI eject command */ 103 UQ_MSC_EJECT_REZERO, /* ejects after SCSI rezero command */ 104 UQ_MSC_EJECT_ZTESTOR, /* ejects after ZTE SCSI command */ 105 UQ_MSC_EJECT_CMOTECH, /* ejects after C-motech SCSI cmd */ 106 UQ_MSC_EJECT_WAIT, /* wait for the device to eject */ 107 UQ_MSC_EJECT_SAEL_M460, /* ejects after Sael USB commands */ 108 UQ_MSC_EJECT_HUAWEISCSI, /* ejects after Huawei SCSI command */ 109 UQ_MSC_EJECT_HUAWEISCSI2, /* ejects after Huawei SCSI 2 command */ 110 UQ_MSC_EJECT_HUAWEISCSI3, /* ejects after Huawei SCSI 3 command */ 111 UQ_MSC_EJECT_HUAWEISCSI4, /* ejects after Huawei SCSI 4 command */ 112 UQ_MSC_EJECT_TCT, /* ejects after TCT SCSI command */ 113 114 UQ_BAD_MIDI, /* device claims MIDI class, but isn't */ 115 UQ_AU_VENDOR_CLASS, /* audio device uses vendor and not audio class */ 116 UQ_SINGLE_CMD_MIDI, /* at most one command per USB packet */ 117 UQ_MSC_DYMO_EJECT, /* ejects Dymo MSC device */ 118 UQ_AU_SET_SPDIF_CM6206, /* enable S/PDIF audio output */ 119 UQ_WMT_IGNORE, /* device should be ignored by wmt driver */ 120 121 USB_QUIRK_MAX 122 }; 123 124 uint8_t usb_test_quirk(const struct usb_attach_arg *uaa, uint16_t quirk); 125 126 #endif /* _USB_QUIRK_H_ */ 127