1 /*- 2 * Copyright (c) 2012 3 * Ben Gray <bgray@freebsd.org>. 4 * All rights reserved. 5 * 6 * Redistribution and use in source and binary forms, with or without 7 * modification, are permitted provided that the following conditions 8 * are met: 9 * 1. Redistributions of source code must retain the above copyright 10 * notice, this list of conditions and the following disclaimer. 11 * 2. Redistributions in binary form must reproduce the above copyright 12 * notice, this list of conditions and the following disclaimer in the 13 * documentation and/or other materials provided with the distribution. 14 * 15 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR 16 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES 17 * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. 18 * IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, 19 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT 20 * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, 21 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY 22 * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT 23 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF 24 * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 25 */ 26 27 #include <sys/cdefs.h> 28 __FBSDID("$FreeBSD$"); 29 30 /* 31 * SMSC LAN9xxx devices (http://www.smsc.com/) 32 * 33 * The LAN9500 & LAN9500A devices are stand-alone USB to Ethernet chips that 34 * support USB 2.0 and 10/100 Mbps Ethernet. 35 * 36 * The LAN951x devices are an integrated USB hub and USB to Ethernet adapter. 37 * The driver only covers the Ethernet part, the standard USB hub driver 38 * supports the hub part. 39 * 40 * This driver is closely modelled on the Linux driver written and copyrighted 41 * by SMSC. 42 * 43 * 44 * 45 * 46 * H/W TCP & UDP Checksum Offloading 47 * --------------------------------- 48 * The chip supports both tx and rx offloading of UDP & TCP checksums, this 49 * feature can be dynamically enabled/disabled. 50 * 51 * RX checksuming is performed across bytes after the IPv4 header to the end of 52 * the Ethernet frame, this means if the frame is padded with non-zero values 53 * the H/W checksum will be incorrect, however the rx code compensates for this. 54 * 55 * TX checksuming is more complicated, the device requires a special header to 56 * be prefixed onto the start of the frame which indicates the start and end 57 * positions of the UDP or TCP frame. This requires the driver to manually 58 * go through the packet data and decode the headers prior to sending. 59 * On Linux they generally provide cues to the location of the csum and the 60 * area to calculate it over, on FreeBSD we seem to have to do it all ourselves, 61 * hence this is not as optimal and therefore h/w tX checksum is currently not 62 * implemented. 63 * 64 */ 65 #include <sys/stdint.h> 66 #include <sys/stddef.h> 67 #include <sys/param.h> 68 #include <sys/queue.h> 69 #include <sys/types.h> 70 #include <sys/systm.h> 71 #include <sys/kernel.h> 72 #include <sys/bus.h> 73 #include <sys/module.h> 74 #include <sys/lock.h> 75 #include <sys/mutex.h> 76 #include <sys/condvar.h> 77 #include <sys/socket.h> 78 #include <sys/sysctl.h> 79 #include <sys/sx.h> 80 #include <sys/unistd.h> 81 #include <sys/callout.h> 82 #include <sys/malloc.h> 83 #include <sys/priv.h> 84 #include <sys/random.h> 85 86 #include <net/if.h> 87 #include <net/if_var.h> 88 89 #include <netinet/in.h> 90 #include <netinet/ip.h> 91 92 #include "opt_platform.h" 93 94 #ifdef FDT 95 #include <dev/fdt/fdt_common.h> 96 #include <dev/ofw/ofw_bus.h> 97 #include <dev/ofw/ofw_bus_subr.h> 98 #endif 99 100 #include <dev/usb/usb.h> 101 #include <dev/usb/usbdi.h> 102 #include <dev/usb/usbdi_util.h> 103 #include "usbdevs.h" 104 105 #define USB_DEBUG_VAR smsc_debug 106 #include <dev/usb/usb_debug.h> 107 #include <dev/usb/usb_process.h> 108 109 #include <dev/usb/net/usb_ethernet.h> 110 111 #include <dev/usb/net/if_smscreg.h> 112 113 #ifdef USB_DEBUG 114 static int smsc_debug = 0; 115 116 SYSCTL_NODE(_hw_usb, OID_AUTO, smsc, CTLFLAG_RW, 0, "USB smsc"); 117 SYSCTL_INT(_hw_usb_smsc, OID_AUTO, debug, CTLFLAG_RWTUN, &smsc_debug, 0, 118 "Debug level"); 119 #endif 120 121 /* 122 * Various supported device vendors/products. 123 */ 124 static const struct usb_device_id smsc_devs[] = { 125 #define SMSC_DEV(p,i) { USB_VPI(USB_VENDOR_SMC2, USB_PRODUCT_SMC2_##p, i) } 126 SMSC_DEV(LAN89530_ETH, 0), 127 SMSC_DEV(LAN9500_ETH, 0), 128 SMSC_DEV(LAN9500_ETH_2, 0), 129 SMSC_DEV(LAN9500A_ETH, 0), 130 SMSC_DEV(LAN9500A_ETH_2, 0), 131 SMSC_DEV(LAN9505_ETH, 0), 132 SMSC_DEV(LAN9505A_ETH, 0), 133 SMSC_DEV(LAN9514_ETH, 0), 134 SMSC_DEV(LAN9514_ETH_2, 0), 135 SMSC_DEV(LAN9530_ETH, 0), 136 SMSC_DEV(LAN9730_ETH, 0), 137 SMSC_DEV(LAN9500_SAL10, 0), 138 SMSC_DEV(LAN9505_SAL10, 0), 139 SMSC_DEV(LAN9500A_SAL10, 0), 140 SMSC_DEV(LAN9505A_SAL10, 0), 141 SMSC_DEV(LAN9514_SAL10, 0), 142 SMSC_DEV(LAN9500A_HAL, 0), 143 SMSC_DEV(LAN9505A_HAL, 0), 144 #undef SMSC_DEV 145 }; 146 147 148 #ifdef USB_DEBUG 149 #define smsc_dbg_printf(sc, fmt, args...) \ 150 do { \ 151 if (smsc_debug > 0) \ 152 device_printf((sc)->sc_ue.ue_dev, "debug: " fmt, ##args); \ 153 } while(0) 154 #else 155 #define smsc_dbg_printf(sc, fmt, args...) 156 #endif 157 158 #define smsc_warn_printf(sc, fmt, args...) \ 159 device_printf((sc)->sc_ue.ue_dev, "warning: " fmt, ##args) 160 161 #define smsc_err_printf(sc, fmt, args...) \ 162 device_printf((sc)->sc_ue.ue_dev, "error: " fmt, ##args) 163 164 165 #define ETHER_IS_ZERO(addr) \ 166 (!(addr[0] | addr[1] | addr[2] | addr[3] | addr[4] | addr[5])) 167 168 #define ETHER_IS_VALID(addr) \ 169 (!ETHER_IS_MULTICAST(addr) && !ETHER_IS_ZERO(addr)) 170 171 static device_probe_t smsc_probe; 172 static device_attach_t smsc_attach; 173 static device_detach_t smsc_detach; 174 175 static usb_callback_t smsc_bulk_read_callback; 176 static usb_callback_t smsc_bulk_write_callback; 177 178 static miibus_readreg_t smsc_miibus_readreg; 179 static miibus_writereg_t smsc_miibus_writereg; 180 static miibus_statchg_t smsc_miibus_statchg; 181 182 #if __FreeBSD_version > 1000000 183 static int smsc_attach_post_sub(struct usb_ether *ue); 184 #endif 185 static uether_fn_t smsc_attach_post; 186 static uether_fn_t smsc_init; 187 static uether_fn_t smsc_stop; 188 static uether_fn_t smsc_start; 189 static uether_fn_t smsc_tick; 190 static uether_fn_t smsc_setmulti; 191 static uether_fn_t smsc_setpromisc; 192 193 static int smsc_ifmedia_upd(struct ifnet *); 194 static void smsc_ifmedia_sts(struct ifnet *, struct ifmediareq *); 195 196 static int smsc_chip_init(struct smsc_softc *sc); 197 static int smsc_ioctl(struct ifnet *ifp, u_long cmd, caddr_t data); 198 199 static const struct usb_config smsc_config[SMSC_N_TRANSFER] = { 200 201 [SMSC_BULK_DT_WR] = { 202 .type = UE_BULK, 203 .endpoint = UE_ADDR_ANY, 204 .direction = UE_DIR_OUT, 205 .frames = 16, 206 .bufsize = 16 * (MCLBYTES + 16), 207 .flags = {.pipe_bof = 1,.force_short_xfer = 1,}, 208 .callback = smsc_bulk_write_callback, 209 .timeout = 10000, /* 10 seconds */ 210 }, 211 212 [SMSC_BULK_DT_RD] = { 213 .type = UE_BULK, 214 .endpoint = UE_ADDR_ANY, 215 .direction = UE_DIR_IN, 216 .bufsize = 20480, /* bytes */ 217 .flags = {.pipe_bof = 1,.short_xfer_ok = 1,}, 218 .callback = smsc_bulk_read_callback, 219 .timeout = 0, /* no timeout */ 220 }, 221 222 /* The SMSC chip supports an interrupt endpoints, however they aren't 223 * needed as we poll on the MII status. 224 */ 225 }; 226 227 static const struct usb_ether_methods smsc_ue_methods = { 228 .ue_attach_post = smsc_attach_post, 229 #if __FreeBSD_version > 1000000 230 .ue_attach_post_sub = smsc_attach_post_sub, 231 #endif 232 .ue_start = smsc_start, 233 .ue_ioctl = smsc_ioctl, 234 .ue_init = smsc_init, 235 .ue_stop = smsc_stop, 236 .ue_tick = smsc_tick, 237 .ue_setmulti = smsc_setmulti, 238 .ue_setpromisc = smsc_setpromisc, 239 .ue_mii_upd = smsc_ifmedia_upd, 240 .ue_mii_sts = smsc_ifmedia_sts, 241 }; 242 243 /** 244 * smsc_read_reg - Reads a 32-bit register on the device 245 * @sc: driver soft context 246 * @off: offset of the register 247 * @data: pointer a value that will be populated with the register value 248 * 249 * LOCKING: 250 * The device lock must be held before calling this function. 251 * 252 * RETURNS: 253 * 0 on success, a USB_ERR_?? error code on failure. 254 */ 255 static int 256 smsc_read_reg(struct smsc_softc *sc, uint32_t off, uint32_t *data) 257 { 258 struct usb_device_request req; 259 uint32_t buf; 260 usb_error_t err; 261 262 SMSC_LOCK_ASSERT(sc, MA_OWNED); 263 264 req.bmRequestType = UT_READ_VENDOR_DEVICE; 265 req.bRequest = SMSC_UR_READ_REG; 266 USETW(req.wValue, 0); 267 USETW(req.wIndex, off); 268 USETW(req.wLength, 4); 269 270 err = uether_do_request(&sc->sc_ue, &req, &buf, 1000); 271 if (err != 0) 272 smsc_warn_printf(sc, "Failed to read register 0x%0x\n", off); 273 274 *data = le32toh(buf); 275 276 return (err); 277 } 278 279 /** 280 * smsc_write_reg - Writes a 32-bit register on the device 281 * @sc: driver soft context 282 * @off: offset of the register 283 * @data: the 32-bit value to write into the register 284 * 285 * LOCKING: 286 * The device lock must be held before calling this function. 287 * 288 * RETURNS: 289 * 0 on success, a USB_ERR_?? error code on failure. 290 */ 291 static int 292 smsc_write_reg(struct smsc_softc *sc, uint32_t off, uint32_t data) 293 { 294 struct usb_device_request req; 295 uint32_t buf; 296 usb_error_t err; 297 298 SMSC_LOCK_ASSERT(sc, MA_OWNED); 299 300 buf = htole32(data); 301 302 req.bmRequestType = UT_WRITE_VENDOR_DEVICE; 303 req.bRequest = SMSC_UR_WRITE_REG; 304 USETW(req.wValue, 0); 305 USETW(req.wIndex, off); 306 USETW(req.wLength, 4); 307 308 err = uether_do_request(&sc->sc_ue, &req, &buf, 1000); 309 if (err != 0) 310 smsc_warn_printf(sc, "Failed to write register 0x%0x\n", off); 311 312 return (err); 313 } 314 315 /** 316 * smsc_wait_for_bits - Polls on a register value until bits are cleared 317 * @sc: soft context 318 * @reg: offset of the register 319 * @bits: if the bits are clear the function returns 320 * 321 * LOCKING: 322 * The device lock must be held before calling this function. 323 * 324 * RETURNS: 325 * 0 on success, or a USB_ERR_?? error code on failure. 326 */ 327 static int 328 smsc_wait_for_bits(struct smsc_softc *sc, uint32_t reg, uint32_t bits) 329 { 330 usb_ticks_t start_ticks; 331 const usb_ticks_t max_ticks = USB_MS_TO_TICKS(1000); 332 uint32_t val; 333 int err; 334 335 SMSC_LOCK_ASSERT(sc, MA_OWNED); 336 337 start_ticks = (usb_ticks_t)ticks; 338 do { 339 if ((err = smsc_read_reg(sc, reg, &val)) != 0) 340 return (err); 341 if (!(val & bits)) 342 return (0); 343 344 uether_pause(&sc->sc_ue, hz / 100); 345 } while (((usb_ticks_t)(ticks - start_ticks)) < max_ticks); 346 347 return (USB_ERR_TIMEOUT); 348 } 349 350 /** 351 * smsc_eeprom_read - Reads the attached EEPROM 352 * @sc: soft context 353 * @off: the eeprom address offset 354 * @buf: stores the bytes 355 * @buflen: the number of bytes to read 356 * 357 * Simply reads bytes from an attached eeprom. 358 * 359 * LOCKING: 360 * The function takes and releases the device lock if it is not already held. 361 * 362 * RETURNS: 363 * 0 on success, or a USB_ERR_?? error code on failure. 364 */ 365 static int 366 smsc_eeprom_read(struct smsc_softc *sc, uint16_t off, uint8_t *buf, uint16_t buflen) 367 { 368 usb_ticks_t start_ticks; 369 const usb_ticks_t max_ticks = USB_MS_TO_TICKS(1000); 370 int err; 371 int locked; 372 uint32_t val; 373 uint16_t i; 374 375 locked = mtx_owned(&sc->sc_mtx); 376 if (!locked) 377 SMSC_LOCK(sc); 378 379 err = smsc_wait_for_bits(sc, SMSC_EEPROM_CMD, SMSC_EEPROM_CMD_BUSY); 380 if (err != 0) { 381 smsc_warn_printf(sc, "eeprom busy, failed to read data\n"); 382 goto done; 383 } 384 385 /* start reading the bytes, one at a time */ 386 for (i = 0; i < buflen; i++) { 387 388 val = SMSC_EEPROM_CMD_BUSY | (SMSC_EEPROM_CMD_ADDR_MASK & (off + i)); 389 if ((err = smsc_write_reg(sc, SMSC_EEPROM_CMD, val)) != 0) 390 goto done; 391 392 start_ticks = (usb_ticks_t)ticks; 393 do { 394 if ((err = smsc_read_reg(sc, SMSC_EEPROM_CMD, &val)) != 0) 395 goto done; 396 if (!(val & SMSC_EEPROM_CMD_BUSY) || (val & SMSC_EEPROM_CMD_TIMEOUT)) 397 break; 398 399 uether_pause(&sc->sc_ue, hz / 100); 400 } while (((usb_ticks_t)(ticks - start_ticks)) < max_ticks); 401 402 if (val & (SMSC_EEPROM_CMD_BUSY | SMSC_EEPROM_CMD_TIMEOUT)) { 403 smsc_warn_printf(sc, "eeprom command failed\n"); 404 err = USB_ERR_IOERROR; 405 break; 406 } 407 408 if ((err = smsc_read_reg(sc, SMSC_EEPROM_DATA, &val)) != 0) 409 goto done; 410 411 buf[i] = (val & 0xff); 412 } 413 414 done: 415 if (!locked) 416 SMSC_UNLOCK(sc); 417 418 return (err); 419 } 420 421 /** 422 * smsc_miibus_readreg - Reads a MII/MDIO register 423 * @dev: usb ether device 424 * @phy: the number of phy reading from 425 * @reg: the register address 426 * 427 * Attempts to read a phy register over the MII bus. 428 * 429 * LOCKING: 430 * Takes and releases the device mutex lock if not already held. 431 * 432 * RETURNS: 433 * Returns the 16-bits read from the MII register, if this function fails 0 434 * is returned. 435 */ 436 static int 437 smsc_miibus_readreg(device_t dev, int phy, int reg) 438 { 439 struct smsc_softc *sc = device_get_softc(dev); 440 int locked; 441 uint32_t addr; 442 uint32_t val = 0; 443 444 locked = mtx_owned(&sc->sc_mtx); 445 if (!locked) 446 SMSC_LOCK(sc); 447 448 if (smsc_wait_for_bits(sc, SMSC_MII_ADDR, SMSC_MII_BUSY) != 0) { 449 smsc_warn_printf(sc, "MII is busy\n"); 450 goto done; 451 } 452 453 addr = (phy << 11) | (reg << 6) | SMSC_MII_READ; 454 smsc_write_reg(sc, SMSC_MII_ADDR, addr); 455 456 if (smsc_wait_for_bits(sc, SMSC_MII_ADDR, SMSC_MII_BUSY) != 0) 457 smsc_warn_printf(sc, "MII read timeout\n"); 458 459 smsc_read_reg(sc, SMSC_MII_DATA, &val); 460 val = le32toh(val); 461 462 done: 463 if (!locked) 464 SMSC_UNLOCK(sc); 465 466 return (val & 0xFFFF); 467 } 468 469 /** 470 * smsc_miibus_writereg - Writes a MII/MDIO register 471 * @dev: usb ether device 472 * @phy: the number of phy writing to 473 * @reg: the register address 474 * @val: the value to write 475 * 476 * Attempts to write a phy register over the MII bus. 477 * 478 * LOCKING: 479 * Takes and releases the device mutex lock if not already held. 480 * 481 * RETURNS: 482 * Always returns 0 regardless of success or failure. 483 */ 484 static int 485 smsc_miibus_writereg(device_t dev, int phy, int reg, int val) 486 { 487 struct smsc_softc *sc = device_get_softc(dev); 488 int locked; 489 uint32_t addr; 490 491 if (sc->sc_phyno != phy) 492 return (0); 493 494 locked = mtx_owned(&sc->sc_mtx); 495 if (!locked) 496 SMSC_LOCK(sc); 497 498 if (smsc_wait_for_bits(sc, SMSC_MII_ADDR, SMSC_MII_BUSY) != 0) { 499 smsc_warn_printf(sc, "MII is busy\n"); 500 goto done; 501 } 502 503 val = htole32(val); 504 smsc_write_reg(sc, SMSC_MII_DATA, val); 505 506 addr = (phy << 11) | (reg << 6) | SMSC_MII_WRITE; 507 smsc_write_reg(sc, SMSC_MII_ADDR, addr); 508 509 if (smsc_wait_for_bits(sc, SMSC_MII_ADDR, SMSC_MII_BUSY) != 0) 510 smsc_warn_printf(sc, "MII write timeout\n"); 511 512 done: 513 if (!locked) 514 SMSC_UNLOCK(sc); 515 return (0); 516 } 517 518 519 520 /** 521 * smsc_miibus_statchg - Called to detect phy status change 522 * @dev: usb ether device 523 * 524 * This function is called periodically by the system to poll for status 525 * changes of the link. 526 * 527 * LOCKING: 528 * Takes and releases the device mutex lock if not already held. 529 */ 530 static void 531 smsc_miibus_statchg(device_t dev) 532 { 533 struct smsc_softc *sc = device_get_softc(dev); 534 struct mii_data *mii = uether_getmii(&sc->sc_ue); 535 struct ifnet *ifp; 536 int locked; 537 int err; 538 uint32_t flow; 539 uint32_t afc_cfg; 540 541 locked = mtx_owned(&sc->sc_mtx); 542 if (!locked) 543 SMSC_LOCK(sc); 544 545 ifp = uether_getifp(&sc->sc_ue); 546 if (mii == NULL || ifp == NULL || 547 (ifp->if_drv_flags & IFF_DRV_RUNNING) == 0) 548 goto done; 549 550 /* Use the MII status to determine link status */ 551 sc->sc_flags &= ~SMSC_FLAG_LINK; 552 if ((mii->mii_media_status & (IFM_ACTIVE | IFM_AVALID)) == 553 (IFM_ACTIVE | IFM_AVALID)) { 554 switch (IFM_SUBTYPE(mii->mii_media_active)) { 555 case IFM_10_T: 556 case IFM_100_TX: 557 sc->sc_flags |= SMSC_FLAG_LINK; 558 break; 559 case IFM_1000_T: 560 /* Gigabit ethernet not supported by chipset */ 561 break; 562 default: 563 break; 564 } 565 } 566 567 /* Lost link, do nothing. */ 568 if ((sc->sc_flags & SMSC_FLAG_LINK) == 0) { 569 smsc_dbg_printf(sc, "link flag not set\n"); 570 goto done; 571 } 572 573 err = smsc_read_reg(sc, SMSC_AFC_CFG, &afc_cfg); 574 if (err) { 575 smsc_warn_printf(sc, "failed to read initial AFC_CFG, error %d\n", err); 576 goto done; 577 } 578 579 /* Enable/disable full duplex operation and TX/RX pause */ 580 if ((IFM_OPTIONS(mii->mii_media_active) & IFM_FDX) != 0) { 581 smsc_dbg_printf(sc, "full duplex operation\n"); 582 sc->sc_mac_csr &= ~SMSC_MAC_CSR_RCVOWN; 583 sc->sc_mac_csr |= SMSC_MAC_CSR_FDPX; 584 585 if ((IFM_OPTIONS(mii->mii_media_active) & IFM_ETH_RXPAUSE) != 0) 586 flow = 0xffff0002; 587 else 588 flow = 0; 589 590 if ((IFM_OPTIONS(mii->mii_media_active) & IFM_ETH_TXPAUSE) != 0) 591 afc_cfg |= 0xf; 592 else 593 afc_cfg &= ~0xf; 594 595 } else { 596 smsc_dbg_printf(sc, "half duplex operation\n"); 597 sc->sc_mac_csr &= ~SMSC_MAC_CSR_FDPX; 598 sc->sc_mac_csr |= SMSC_MAC_CSR_RCVOWN; 599 600 flow = 0; 601 afc_cfg |= 0xf; 602 } 603 604 err = smsc_write_reg(sc, SMSC_MAC_CSR, sc->sc_mac_csr); 605 err += smsc_write_reg(sc, SMSC_FLOW, flow); 606 err += smsc_write_reg(sc, SMSC_AFC_CFG, afc_cfg); 607 if (err) 608 smsc_warn_printf(sc, "media change failed, error %d\n", err); 609 610 done: 611 if (!locked) 612 SMSC_UNLOCK(sc); 613 } 614 615 /** 616 * smsc_ifmedia_upd - Set media options 617 * @ifp: interface pointer 618 * 619 * Basically boilerplate code that simply calls the mii functions to set the 620 * media options. 621 * 622 * LOCKING: 623 * The device lock must be held before this function is called. 624 * 625 * RETURNS: 626 * Returns 0 on success or a negative error code. 627 */ 628 static int 629 smsc_ifmedia_upd(struct ifnet *ifp) 630 { 631 struct smsc_softc *sc = ifp->if_softc; 632 struct mii_data *mii = uether_getmii(&sc->sc_ue); 633 struct mii_softc *miisc; 634 int err; 635 636 SMSC_LOCK_ASSERT(sc, MA_OWNED); 637 638 LIST_FOREACH(miisc, &mii->mii_phys, mii_list) 639 PHY_RESET(miisc); 640 err = mii_mediachg(mii); 641 return (err); 642 } 643 644 /** 645 * smsc_ifmedia_sts - Report current media status 646 * @ifp: inet interface pointer 647 * @ifmr: interface media request 648 * 649 * Basically boilerplate code that simply calls the mii functions to get the 650 * media status. 651 * 652 * LOCKING: 653 * Internally takes and releases the device lock. 654 */ 655 static void 656 smsc_ifmedia_sts(struct ifnet *ifp, struct ifmediareq *ifmr) 657 { 658 struct smsc_softc *sc = ifp->if_softc; 659 struct mii_data *mii = uether_getmii(&sc->sc_ue); 660 661 SMSC_LOCK(sc); 662 mii_pollstat(mii); 663 ifmr->ifm_active = mii->mii_media_active; 664 ifmr->ifm_status = mii->mii_media_status; 665 SMSC_UNLOCK(sc); 666 } 667 668 /** 669 * smsc_hash - Calculate the hash of a mac address 670 * @addr: The mac address to calculate the hash on 671 * 672 * This function is used when configuring a range of m'cast mac addresses to 673 * filter on. The hash of the mac address is put in the device's mac hash 674 * table. 675 * 676 * RETURNS: 677 * Returns a value from 0-63 value which is the hash of the mac address. 678 */ 679 static inline uint32_t 680 smsc_hash(uint8_t addr[ETHER_ADDR_LEN]) 681 { 682 return (ether_crc32_be(addr, ETHER_ADDR_LEN) >> 26) & 0x3f; 683 } 684 685 /** 686 * smsc_setmulti - Setup multicast 687 * @ue: usb ethernet device context 688 * 689 * Tells the device to either accept frames with a multicast mac address, a 690 * select group of m'cast mac addresses or just the devices mac address. 691 * 692 * LOCKING: 693 * Should be called with the SMSC lock held. 694 */ 695 static void 696 smsc_setmulti(struct usb_ether *ue) 697 { 698 struct smsc_softc *sc = uether_getsc(ue); 699 struct ifnet *ifp = uether_getifp(ue); 700 struct ifmultiaddr *ifma; 701 uint32_t hashtbl[2] = { 0, 0 }; 702 uint32_t hash; 703 704 SMSC_LOCK_ASSERT(sc, MA_OWNED); 705 706 if (ifp->if_flags & (IFF_ALLMULTI | IFF_PROMISC)) { 707 smsc_dbg_printf(sc, "receive all multicast enabled\n"); 708 sc->sc_mac_csr |= SMSC_MAC_CSR_MCPAS; 709 sc->sc_mac_csr &= ~SMSC_MAC_CSR_HPFILT; 710 711 } else { 712 /* Take the lock of the mac address list before hashing each of them */ 713 if_maddr_rlock(ifp); 714 715 if (!TAILQ_EMPTY(&ifp->if_multiaddrs)) { 716 /* We are filtering on a set of address so calculate hashes of each 717 * of the address and set the corresponding bits in the register. 718 */ 719 sc->sc_mac_csr |= SMSC_MAC_CSR_HPFILT; 720 sc->sc_mac_csr &= ~(SMSC_MAC_CSR_PRMS | SMSC_MAC_CSR_MCPAS); 721 722 TAILQ_FOREACH(ifma, &ifp->if_multiaddrs, ifma_link) { 723 if (ifma->ifma_addr->sa_family != AF_LINK) 724 continue; 725 726 hash = smsc_hash(LLADDR((struct sockaddr_dl *)ifma->ifma_addr)); 727 hashtbl[hash >> 5] |= 1 << (hash & 0x1F); 728 } 729 } else { 730 /* Only receive packets with destination set to our mac address */ 731 sc->sc_mac_csr &= ~(SMSC_MAC_CSR_MCPAS | SMSC_MAC_CSR_HPFILT); 732 } 733 734 if_maddr_runlock(ifp); 735 736 /* Debug */ 737 if (sc->sc_mac_csr & SMSC_MAC_CSR_HPFILT) 738 smsc_dbg_printf(sc, "receive select group of macs\n"); 739 else 740 smsc_dbg_printf(sc, "receive own packets only\n"); 741 } 742 743 /* Write the hash table and mac control registers */ 744 smsc_write_reg(sc, SMSC_HASHH, hashtbl[1]); 745 smsc_write_reg(sc, SMSC_HASHL, hashtbl[0]); 746 smsc_write_reg(sc, SMSC_MAC_CSR, sc->sc_mac_csr); 747 } 748 749 750 /** 751 * smsc_setpromisc - Enables/disables promiscuous mode 752 * @ue: usb ethernet device context 753 * 754 * LOCKING: 755 * Should be called with the SMSC lock held. 756 */ 757 static void 758 smsc_setpromisc(struct usb_ether *ue) 759 { 760 struct smsc_softc *sc = uether_getsc(ue); 761 struct ifnet *ifp = uether_getifp(ue); 762 763 smsc_dbg_printf(sc, "promiscuous mode %sabled\n", 764 (ifp->if_flags & IFF_PROMISC) ? "en" : "dis"); 765 766 SMSC_LOCK_ASSERT(sc, MA_OWNED); 767 768 if (ifp->if_flags & IFF_PROMISC) 769 sc->sc_mac_csr |= SMSC_MAC_CSR_PRMS; 770 else 771 sc->sc_mac_csr &= ~SMSC_MAC_CSR_PRMS; 772 773 smsc_write_reg(sc, SMSC_MAC_CSR, sc->sc_mac_csr); 774 } 775 776 777 /** 778 * smsc_sethwcsum - Enable or disable H/W UDP and TCP checksumming 779 * @sc: driver soft context 780 * 781 * LOCKING: 782 * Should be called with the SMSC lock held. 783 * 784 * RETURNS: 785 * Returns 0 on success or a negative error code. 786 */ 787 static int smsc_sethwcsum(struct smsc_softc *sc) 788 { 789 struct ifnet *ifp = uether_getifp(&sc->sc_ue); 790 uint32_t val; 791 int err; 792 793 if (!ifp) 794 return (-EIO); 795 796 SMSC_LOCK_ASSERT(sc, MA_OWNED); 797 798 err = smsc_read_reg(sc, SMSC_COE_CTRL, &val); 799 if (err != 0) { 800 smsc_warn_printf(sc, "failed to read SMSC_COE_CTRL (err=%d)\n", err); 801 return (err); 802 } 803 804 /* Enable/disable the Rx checksum */ 805 if ((ifp->if_capabilities & ifp->if_capenable) & IFCAP_RXCSUM) 806 val |= SMSC_COE_CTRL_RX_EN; 807 else 808 val &= ~SMSC_COE_CTRL_RX_EN; 809 810 /* Enable/disable the Tx checksum (currently not supported) */ 811 if ((ifp->if_capabilities & ifp->if_capenable) & IFCAP_TXCSUM) 812 val |= SMSC_COE_CTRL_TX_EN; 813 else 814 val &= ~SMSC_COE_CTRL_TX_EN; 815 816 err = smsc_write_reg(sc, SMSC_COE_CTRL, val); 817 if (err != 0) { 818 smsc_warn_printf(sc, "failed to write SMSC_COE_CTRL (err=%d)\n", err); 819 return (err); 820 } 821 822 return (0); 823 } 824 825 826 /** 827 * smsc_setmacaddress - Sets the mac address in the device 828 * @sc: driver soft context 829 * @addr: pointer to array contain at least 6 bytes of the mac 830 * 831 * Writes the MAC address into the device, usually the MAC is programmed with 832 * values from the EEPROM. 833 * 834 * LOCKING: 835 * Should be called with the SMSC lock held. 836 * 837 * RETURNS: 838 * Returns 0 on success or a negative error code. 839 */ 840 static int 841 smsc_setmacaddress(struct smsc_softc *sc, const uint8_t *addr) 842 { 843 int err; 844 uint32_t val; 845 846 smsc_dbg_printf(sc, "setting mac address to %02x:%02x:%02x:%02x:%02x:%02x\n", 847 addr[0], addr[1], addr[2], addr[3], addr[4], addr[5]); 848 849 SMSC_LOCK_ASSERT(sc, MA_OWNED); 850 851 val = (addr[3] << 24) | (addr[2] << 16) | (addr[1] << 8) | addr[0]; 852 if ((err = smsc_write_reg(sc, SMSC_MAC_ADDRL, val)) != 0) 853 goto done; 854 855 val = (addr[5] << 8) | addr[4]; 856 err = smsc_write_reg(sc, SMSC_MAC_ADDRH, val); 857 858 done: 859 return (err); 860 } 861 862 /** 863 * smsc_reset - Reset the SMSC chip 864 * @sc: device soft context 865 * 866 * LOCKING: 867 * Should be called with the SMSC lock held. 868 */ 869 static void 870 smsc_reset(struct smsc_softc *sc) 871 { 872 struct usb_config_descriptor *cd; 873 usb_error_t err; 874 875 cd = usbd_get_config_descriptor(sc->sc_ue.ue_udev); 876 877 err = usbd_req_set_config(sc->sc_ue.ue_udev, &sc->sc_mtx, 878 cd->bConfigurationValue); 879 if (err) 880 smsc_warn_printf(sc, "reset failed (ignored)\n"); 881 882 /* Wait a little while for the chip to get its brains in order. */ 883 uether_pause(&sc->sc_ue, hz / 100); 884 885 /* Reinitialize controller to achieve full reset. */ 886 smsc_chip_init(sc); 887 } 888 889 890 /** 891 * smsc_init - Initialises the LAN95xx chip 892 * @ue: USB ether interface 893 * 894 * Called when the interface is brought up (i.e. ifconfig ue0 up), this 895 * initialise the interface and the rx/tx pipes. 896 * 897 * LOCKING: 898 * Should be called with the SMSC lock held. 899 */ 900 static void 901 smsc_init(struct usb_ether *ue) 902 { 903 struct smsc_softc *sc = uether_getsc(ue); 904 struct ifnet *ifp = uether_getifp(ue); 905 906 SMSC_LOCK_ASSERT(sc, MA_OWNED); 907 908 if ((ifp->if_drv_flags & IFF_DRV_RUNNING) != 0) 909 return; 910 911 /* Cancel pending I/O */ 912 smsc_stop(ue); 913 914 #if __FreeBSD_version <= 1000000 915 /* On earlier versions this was the first place we could tell the system 916 * that we supported h/w csuming, however this is only called after the 917 * the interface has been brought up - not ideal. 918 */ 919 if (!(ifp->if_capabilities & IFCAP_RXCSUM)) { 920 ifp->if_capabilities |= IFCAP_RXCSUM; 921 ifp->if_capenable |= IFCAP_RXCSUM; 922 ifp->if_hwassist = 0; 923 } 924 925 /* TX checksuming is disabled for now 926 ifp->if_capabilities |= IFCAP_TXCSUM; 927 ifp->if_capenable |= IFCAP_TXCSUM; 928 ifp->if_hwassist = CSUM_TCP | CSUM_UDP; 929 */ 930 #endif 931 932 /* Reset the ethernet interface. */ 933 smsc_reset(sc); 934 935 /* Load the multicast filter. */ 936 smsc_setmulti(ue); 937 938 /* TCP/UDP checksum offload engines. */ 939 smsc_sethwcsum(sc); 940 941 usbd_xfer_set_stall(sc->sc_xfer[SMSC_BULK_DT_WR]); 942 943 /* Indicate we are up and running. */ 944 ifp->if_drv_flags |= IFF_DRV_RUNNING; 945 946 /* Switch to selected media. */ 947 smsc_ifmedia_upd(ifp); 948 smsc_start(ue); 949 } 950 951 /** 952 * smsc_bulk_read_callback - Read callback used to process the USB URB 953 * @xfer: the USB transfer 954 * @error: 955 * 956 * Reads the URB data which can contain one or more ethernet frames, the 957 * frames are copyed into a mbuf and given to the system. 958 * 959 * LOCKING: 960 * No locking required, doesn't access internal driver settings. 961 */ 962 static void 963 smsc_bulk_read_callback(struct usb_xfer *xfer, usb_error_t error) 964 { 965 struct smsc_softc *sc = usbd_xfer_softc(xfer); 966 struct usb_ether *ue = &sc->sc_ue; 967 struct ifnet *ifp = uether_getifp(ue); 968 struct mbuf *m; 969 struct usb_page_cache *pc; 970 uint32_t rxhdr; 971 uint16_t pktlen; 972 int off; 973 int actlen; 974 975 usbd_xfer_status(xfer, &actlen, NULL, NULL, NULL); 976 smsc_dbg_printf(sc, "rx : actlen %d\n", actlen); 977 978 switch (USB_GET_STATE(xfer)) { 979 case USB_ST_TRANSFERRED: 980 981 /* There is always a zero length frame after bringing the IF up */ 982 if (actlen < (sizeof(rxhdr) + ETHER_CRC_LEN)) 983 goto tr_setup; 984 985 /* There maybe multiple packets in the USB frame, each will have a 986 * header and each needs to have it's own mbuf allocated and populated 987 * for it. 988 */ 989 pc = usbd_xfer_get_frame(xfer, 0); 990 off = 0; 991 992 while (off < actlen) { 993 994 /* The frame header is always aligned on a 4 byte boundary */ 995 off = ((off + 0x3) & ~0x3); 996 997 usbd_copy_out(pc, off, &rxhdr, sizeof(rxhdr)); 998 off += (sizeof(rxhdr) + ETHER_ALIGN); 999 rxhdr = le32toh(rxhdr); 1000 1001 pktlen = (uint16_t)SMSC_RX_STAT_FRM_LENGTH(rxhdr); 1002 1003 smsc_dbg_printf(sc, "rx : rxhdr 0x%08x : pktlen %d : actlen %d : " 1004 "off %d\n", rxhdr, pktlen, actlen, off); 1005 1006 1007 if (rxhdr & SMSC_RX_STAT_ERROR) { 1008 smsc_dbg_printf(sc, "rx error (hdr 0x%08x)\n", rxhdr); 1009 if_inc_counter(ifp, IFCOUNTER_IERRORS, 1); 1010 if (rxhdr & SMSC_RX_STAT_COLLISION) 1011 if_inc_counter(ifp, IFCOUNTER_COLLISIONS, 1); 1012 } else { 1013 1014 /* Check if the ethernet frame is too big or too small */ 1015 if ((pktlen < ETHER_HDR_LEN) || (pktlen > (actlen - off))) 1016 goto tr_setup; 1017 1018 /* Create a new mbuf to store the packet in */ 1019 m = uether_newbuf(); 1020 if (m == NULL) { 1021 smsc_warn_printf(sc, "failed to create new mbuf\n"); 1022 if_inc_counter(ifp, IFCOUNTER_IQDROPS, 1); 1023 goto tr_setup; 1024 } 1025 1026 usbd_copy_out(pc, off, mtod(m, uint8_t *), pktlen); 1027 1028 /* Check if RX TCP/UDP checksumming is being offloaded */ 1029 if ((ifp->if_capenable & IFCAP_RXCSUM) != 0) { 1030 1031 struct ether_header *eh; 1032 1033 eh = mtod(m, struct ether_header *); 1034 1035 /* Remove the extra 2 bytes of the csum */ 1036 pktlen -= 2; 1037 1038 /* The checksum appears to be simplistically calculated 1039 * over the udp/tcp header and data up to the end of the 1040 * eth frame. Which means if the eth frame is padded 1041 * the csum calculation is incorrectly performed over 1042 * the padding bytes as well. Therefore to be safe we 1043 * ignore the H/W csum on frames less than or equal to 1044 * 64 bytes. 1045 * 1046 * Ignore H/W csum for non-IPv4 packets. 1047 */ 1048 if ((be16toh(eh->ether_type) == ETHERTYPE_IP) && 1049 (pktlen > ETHER_MIN_LEN)) { 1050 struct ip *ip; 1051 1052 ip = (struct ip *)(eh + 1); 1053 if ((ip->ip_v == IPVERSION) && 1054 ((ip->ip_p == IPPROTO_TCP) || 1055 (ip->ip_p == IPPROTO_UDP))) { 1056 /* Indicate the UDP/TCP csum has been calculated */ 1057 m->m_pkthdr.csum_flags |= CSUM_DATA_VALID; 1058 1059 /* Copy the TCP/UDP checksum from the last 2 bytes 1060 * of the transfer and put in the csum_data field. 1061 */ 1062 usbd_copy_out(pc, (off + pktlen), 1063 &m->m_pkthdr.csum_data, 2); 1064 1065 /* The data is copied in network order, but the 1066 * csum algorithm in the kernel expects it to be 1067 * in host network order. 1068 */ 1069 m->m_pkthdr.csum_data = ntohs(m->m_pkthdr.csum_data); 1070 1071 smsc_dbg_printf(sc, "RX checksum offloaded (0x%04x)\n", 1072 m->m_pkthdr.csum_data); 1073 } 1074 } 1075 1076 /* Need to adjust the offset as well or we'll be off 1077 * by 2 because the csum is removed from the packet 1078 * length. 1079 */ 1080 off += 2; 1081 } 1082 1083 /* Finally enqueue the mbuf on the receive queue */ 1084 /* Remove 4 trailing bytes */ 1085 if (pktlen < (4 + ETHER_HDR_LEN)) { 1086 m_freem(m); 1087 goto tr_setup; 1088 } 1089 uether_rxmbuf(ue, m, pktlen - 4); 1090 } 1091 1092 /* Update the offset to move to the next potential packet */ 1093 off += pktlen; 1094 } 1095 1096 /* FALLTHROUGH */ 1097 1098 case USB_ST_SETUP: 1099 tr_setup: 1100 usbd_xfer_set_frame_len(xfer, 0, usbd_xfer_max_len(xfer)); 1101 usbd_transfer_submit(xfer); 1102 uether_rxflush(ue); 1103 return; 1104 1105 default: 1106 if (error != USB_ERR_CANCELLED) { 1107 smsc_warn_printf(sc, "bulk read error, %s\n", usbd_errstr(error)); 1108 usbd_xfer_set_stall(xfer); 1109 goto tr_setup; 1110 } 1111 return; 1112 } 1113 } 1114 1115 /** 1116 * smsc_bulk_write_callback - Write callback used to send ethernet frame(s) 1117 * @xfer: the USB transfer 1118 * @error: error code if the transfers is in an errored state 1119 * 1120 * The main write function that pulls ethernet frames off the queue and sends 1121 * them out. 1122 * 1123 * LOCKING: 1124 * 1125 */ 1126 static void 1127 smsc_bulk_write_callback(struct usb_xfer *xfer, usb_error_t error) 1128 { 1129 struct smsc_softc *sc = usbd_xfer_softc(xfer); 1130 struct ifnet *ifp = uether_getifp(&sc->sc_ue); 1131 struct usb_page_cache *pc; 1132 struct mbuf *m; 1133 uint32_t txhdr; 1134 uint32_t frm_len = 0; 1135 int nframes; 1136 1137 switch (USB_GET_STATE(xfer)) { 1138 case USB_ST_TRANSFERRED: 1139 ifp->if_drv_flags &= ~IFF_DRV_OACTIVE; 1140 /* FALLTHROUGH */ 1141 1142 case USB_ST_SETUP: 1143 tr_setup: 1144 if ((sc->sc_flags & SMSC_FLAG_LINK) == 0 || 1145 (ifp->if_drv_flags & IFF_DRV_OACTIVE) != 0) { 1146 /* Don't send anything if there is no link or controller is busy. */ 1147 return; 1148 } 1149 1150 for (nframes = 0; nframes < 16 && 1151 !IFQ_DRV_IS_EMPTY(&ifp->if_snd); nframes++) { 1152 IFQ_DRV_DEQUEUE(&ifp->if_snd, m); 1153 if (m == NULL) 1154 break; 1155 usbd_xfer_set_frame_offset(xfer, nframes * MCLBYTES, 1156 nframes); 1157 frm_len = 0; 1158 pc = usbd_xfer_get_frame(xfer, nframes); 1159 1160 /* Each frame is prefixed with two 32-bit values describing the 1161 * length of the packet and buffer. 1162 */ 1163 txhdr = SMSC_TX_CTRL_0_BUF_SIZE(m->m_pkthdr.len) | 1164 SMSC_TX_CTRL_0_FIRST_SEG | SMSC_TX_CTRL_0_LAST_SEG; 1165 txhdr = htole32(txhdr); 1166 usbd_copy_in(pc, 0, &txhdr, sizeof(txhdr)); 1167 1168 txhdr = SMSC_TX_CTRL_1_PKT_LENGTH(m->m_pkthdr.len); 1169 txhdr = htole32(txhdr); 1170 usbd_copy_in(pc, 4, &txhdr, sizeof(txhdr)); 1171 1172 frm_len += 8; 1173 1174 /* Next copy in the actual packet */ 1175 usbd_m_copy_in(pc, frm_len, m, 0, m->m_pkthdr.len); 1176 frm_len += m->m_pkthdr.len; 1177 1178 if_inc_counter(ifp, IFCOUNTER_OPACKETS, 1); 1179 1180 /* If there's a BPF listener, bounce a copy of this frame to him */ 1181 BPF_MTAP(ifp, m); 1182 1183 m_freem(m); 1184 1185 /* Set frame length. */ 1186 usbd_xfer_set_frame_len(xfer, nframes, frm_len); 1187 } 1188 if (nframes != 0) { 1189 usbd_xfer_set_frames(xfer, nframes); 1190 usbd_transfer_submit(xfer); 1191 ifp->if_drv_flags |= IFF_DRV_OACTIVE; 1192 } 1193 return; 1194 1195 default: 1196 if_inc_counter(ifp, IFCOUNTER_OERRORS, 1); 1197 ifp->if_drv_flags &= ~IFF_DRV_OACTIVE; 1198 1199 if (error != USB_ERR_CANCELLED) { 1200 smsc_err_printf(sc, "usb error on tx: %s\n", usbd_errstr(error)); 1201 usbd_xfer_set_stall(xfer); 1202 goto tr_setup; 1203 } 1204 return; 1205 } 1206 } 1207 1208 /** 1209 * smsc_tick - Called periodically to monitor the state of the LAN95xx chip 1210 * @ue: USB ether interface 1211 * 1212 * Simply calls the mii status functions to check the state of the link. 1213 * 1214 * LOCKING: 1215 * Should be called with the SMSC lock held. 1216 */ 1217 static void 1218 smsc_tick(struct usb_ether *ue) 1219 { 1220 struct smsc_softc *sc = uether_getsc(ue); 1221 struct mii_data *mii = uether_getmii(&sc->sc_ue); 1222 1223 SMSC_LOCK_ASSERT(sc, MA_OWNED); 1224 1225 mii_tick(mii); 1226 if ((sc->sc_flags & SMSC_FLAG_LINK) == 0) { 1227 smsc_miibus_statchg(ue->ue_dev); 1228 if ((sc->sc_flags & SMSC_FLAG_LINK) != 0) 1229 smsc_start(ue); 1230 } 1231 } 1232 1233 /** 1234 * smsc_start - Starts communication with the LAN95xx chip 1235 * @ue: USB ether interface 1236 * 1237 * 1238 * 1239 */ 1240 static void 1241 smsc_start(struct usb_ether *ue) 1242 { 1243 struct smsc_softc *sc = uether_getsc(ue); 1244 1245 /* 1246 * start the USB transfers, if not already started: 1247 */ 1248 usbd_transfer_start(sc->sc_xfer[SMSC_BULK_DT_RD]); 1249 usbd_transfer_start(sc->sc_xfer[SMSC_BULK_DT_WR]); 1250 } 1251 1252 /** 1253 * smsc_stop - Stops communication with the LAN95xx chip 1254 * @ue: USB ether interface 1255 * 1256 * 1257 * 1258 */ 1259 static void 1260 smsc_stop(struct usb_ether *ue) 1261 { 1262 struct smsc_softc *sc = uether_getsc(ue); 1263 struct ifnet *ifp = uether_getifp(ue); 1264 1265 SMSC_LOCK_ASSERT(sc, MA_OWNED); 1266 1267 ifp->if_drv_flags &= ~(IFF_DRV_RUNNING | IFF_DRV_OACTIVE); 1268 sc->sc_flags &= ~SMSC_FLAG_LINK; 1269 1270 /* 1271 * stop all the transfers, if not already stopped: 1272 */ 1273 usbd_transfer_stop(sc->sc_xfer[SMSC_BULK_DT_WR]); 1274 usbd_transfer_stop(sc->sc_xfer[SMSC_BULK_DT_RD]); 1275 } 1276 1277 /** 1278 * smsc_phy_init - Initialises the in-built SMSC phy 1279 * @sc: driver soft context 1280 * 1281 * Resets the PHY part of the chip and then initialises it to default 1282 * values. The 'link down' and 'auto-negotiation complete' interrupts 1283 * from the PHY are also enabled, however we don't monitor the interrupt 1284 * endpoints for the moment. 1285 * 1286 * RETURNS: 1287 * Returns 0 on success or EIO if failed to reset the PHY. 1288 */ 1289 static int 1290 smsc_phy_init(struct smsc_softc *sc) 1291 { 1292 int bmcr; 1293 usb_ticks_t start_ticks; 1294 const usb_ticks_t max_ticks = USB_MS_TO_TICKS(1000); 1295 1296 SMSC_LOCK_ASSERT(sc, MA_OWNED); 1297 1298 /* Reset phy and wait for reset to complete */ 1299 smsc_miibus_writereg(sc->sc_ue.ue_dev, sc->sc_phyno, MII_BMCR, BMCR_RESET); 1300 1301 start_ticks = ticks; 1302 do { 1303 uether_pause(&sc->sc_ue, hz / 100); 1304 bmcr = smsc_miibus_readreg(sc->sc_ue.ue_dev, sc->sc_phyno, MII_BMCR); 1305 } while ((bmcr & MII_BMCR) && ((ticks - start_ticks) < max_ticks)); 1306 1307 if (((usb_ticks_t)(ticks - start_ticks)) >= max_ticks) { 1308 smsc_err_printf(sc, "PHY reset timed-out"); 1309 return (EIO); 1310 } 1311 1312 smsc_miibus_writereg(sc->sc_ue.ue_dev, sc->sc_phyno, MII_ANAR, 1313 ANAR_10 | ANAR_10_FD | ANAR_TX | ANAR_TX_FD | /* all modes */ 1314 ANAR_CSMA | 1315 ANAR_FC | 1316 ANAR_PAUSE_ASYM); 1317 1318 /* Setup the phy to interrupt when the link goes down or autoneg completes */ 1319 smsc_miibus_readreg(sc->sc_ue.ue_dev, sc->sc_phyno, SMSC_PHY_INTR_STAT); 1320 smsc_miibus_writereg(sc->sc_ue.ue_dev, sc->sc_phyno, SMSC_PHY_INTR_MASK, 1321 (SMSC_PHY_INTR_ANEG_COMP | SMSC_PHY_INTR_LINK_DOWN)); 1322 1323 /* Restart auto-negotation */ 1324 bmcr = smsc_miibus_readreg(sc->sc_ue.ue_dev, sc->sc_phyno, MII_BMCR); 1325 bmcr |= BMCR_STARTNEG; 1326 smsc_miibus_writereg(sc->sc_ue.ue_dev, sc->sc_phyno, MII_BMCR, bmcr); 1327 1328 return (0); 1329 } 1330 1331 1332 /** 1333 * smsc_chip_init - Initialises the chip after power on 1334 * @sc: driver soft context 1335 * 1336 * This initialisation sequence is modelled on the procedure in the Linux 1337 * driver. 1338 * 1339 * RETURNS: 1340 * Returns 0 on success or an error code on failure. 1341 */ 1342 static int 1343 smsc_chip_init(struct smsc_softc *sc) 1344 { 1345 int err; 1346 int locked; 1347 uint32_t reg_val; 1348 int burst_cap; 1349 1350 locked = mtx_owned(&sc->sc_mtx); 1351 if (!locked) 1352 SMSC_LOCK(sc); 1353 1354 /* Enter H/W config mode */ 1355 smsc_write_reg(sc, SMSC_HW_CFG, SMSC_HW_CFG_LRST); 1356 1357 if ((err = smsc_wait_for_bits(sc, SMSC_HW_CFG, SMSC_HW_CFG_LRST)) != 0) { 1358 smsc_warn_printf(sc, "timed-out waiting for reset to complete\n"); 1359 goto init_failed; 1360 } 1361 1362 /* Reset the PHY */ 1363 smsc_write_reg(sc, SMSC_PM_CTRL, SMSC_PM_CTRL_PHY_RST); 1364 1365 if ((err = smsc_wait_for_bits(sc, SMSC_PM_CTRL, SMSC_PM_CTRL_PHY_RST) != 0)) { 1366 smsc_warn_printf(sc, "timed-out waiting for phy reset to complete\n"); 1367 goto init_failed; 1368 } 1369 1370 /* Set the mac address */ 1371 if ((err = smsc_setmacaddress(sc, sc->sc_ue.ue_eaddr)) != 0) { 1372 smsc_warn_printf(sc, "failed to set the MAC address\n"); 1373 goto init_failed; 1374 } 1375 1376 /* Don't know what the HW_CFG_BIR bit is, but following the reset sequence 1377 * as used in the Linux driver. 1378 */ 1379 if ((err = smsc_read_reg(sc, SMSC_HW_CFG, ®_val)) != 0) { 1380 smsc_warn_printf(sc, "failed to read HW_CFG: %d\n", err); 1381 goto init_failed; 1382 } 1383 reg_val |= SMSC_HW_CFG_BIR; 1384 smsc_write_reg(sc, SMSC_HW_CFG, reg_val); 1385 1386 /* There is a so called 'turbo mode' that the linux driver supports, it 1387 * seems to allow you to jam multiple frames per Rx transaction. By default 1388 * this driver supports that and therefore allows multiple frames per URB. 1389 * 1390 * The xfer buffer size needs to reflect this as well, therefore based on 1391 * the calculations in the Linux driver the RX bufsize is set to 18944, 1392 * bufsz = (16 * 1024 + 5 * 512) 1393 * 1394 * Burst capability is the number of URBs that can be in a burst of data/ 1395 * ethernet frames. 1396 */ 1397 if (usbd_get_speed(sc->sc_ue.ue_udev) == USB_SPEED_HIGH) 1398 burst_cap = 37; 1399 else 1400 burst_cap = 128; 1401 1402 smsc_write_reg(sc, SMSC_BURST_CAP, burst_cap); 1403 1404 /* Set the default bulk in delay (magic value from Linux driver) */ 1405 smsc_write_reg(sc, SMSC_BULK_IN_DLY, 0x00002000); 1406 1407 1408 1409 /* 1410 * Initialise the RX interface 1411 */ 1412 if ((err = smsc_read_reg(sc, SMSC_HW_CFG, ®_val)) < 0) { 1413 smsc_warn_printf(sc, "failed to read HW_CFG: (err = %d)\n", err); 1414 goto init_failed; 1415 } 1416 1417 /* Adjust the packet offset in the buffer (designed to try and align IP 1418 * header on 4 byte boundary) 1419 */ 1420 reg_val &= ~SMSC_HW_CFG_RXDOFF; 1421 reg_val |= (ETHER_ALIGN << 9) & SMSC_HW_CFG_RXDOFF; 1422 1423 /* The following setings are used for 'turbo mode', a.k.a multiple frames 1424 * per Rx transaction (again info taken form Linux driver). 1425 */ 1426 reg_val |= (SMSC_HW_CFG_MEF | SMSC_HW_CFG_BCE); 1427 1428 smsc_write_reg(sc, SMSC_HW_CFG, reg_val); 1429 1430 /* Clear the status register ? */ 1431 smsc_write_reg(sc, SMSC_INTR_STATUS, 0xffffffff); 1432 1433 /* Read and display the revision register */ 1434 if ((err = smsc_read_reg(sc, SMSC_ID_REV, &sc->sc_rev_id)) < 0) { 1435 smsc_warn_printf(sc, "failed to read ID_REV (err = %d)\n", err); 1436 goto init_failed; 1437 } 1438 1439 device_printf(sc->sc_ue.ue_dev, "chip 0x%04lx, rev. %04lx\n", 1440 (sc->sc_rev_id & SMSC_ID_REV_CHIP_ID_MASK) >> 16, 1441 (sc->sc_rev_id & SMSC_ID_REV_CHIP_REV_MASK)); 1442 1443 /* GPIO/LED setup */ 1444 reg_val = SMSC_LED_GPIO_CFG_SPD_LED | SMSC_LED_GPIO_CFG_LNK_LED | 1445 SMSC_LED_GPIO_CFG_FDX_LED; 1446 smsc_write_reg(sc, SMSC_LED_GPIO_CFG, reg_val); 1447 1448 /* 1449 * Initialise the TX interface 1450 */ 1451 smsc_write_reg(sc, SMSC_FLOW, 0); 1452 1453 smsc_write_reg(sc, SMSC_AFC_CFG, AFC_CFG_DEFAULT); 1454 1455 /* Read the current MAC configuration */ 1456 if ((err = smsc_read_reg(sc, SMSC_MAC_CSR, &sc->sc_mac_csr)) < 0) { 1457 smsc_warn_printf(sc, "failed to read MAC_CSR (err=%d)\n", err); 1458 goto init_failed; 1459 } 1460 1461 /* Vlan */ 1462 smsc_write_reg(sc, SMSC_VLAN1, (uint32_t)ETHERTYPE_VLAN); 1463 1464 /* 1465 * Initialise the PHY 1466 */ 1467 if ((err = smsc_phy_init(sc)) != 0) 1468 goto init_failed; 1469 1470 1471 /* 1472 * Start TX 1473 */ 1474 sc->sc_mac_csr |= SMSC_MAC_CSR_TXEN; 1475 smsc_write_reg(sc, SMSC_MAC_CSR, sc->sc_mac_csr); 1476 smsc_write_reg(sc, SMSC_TX_CFG, SMSC_TX_CFG_ON); 1477 1478 /* 1479 * Start RX 1480 */ 1481 sc->sc_mac_csr |= SMSC_MAC_CSR_RXEN; 1482 smsc_write_reg(sc, SMSC_MAC_CSR, sc->sc_mac_csr); 1483 1484 if (!locked) 1485 SMSC_UNLOCK(sc); 1486 1487 return (0); 1488 1489 init_failed: 1490 if (!locked) 1491 SMSC_UNLOCK(sc); 1492 1493 smsc_err_printf(sc, "smsc_chip_init failed (err=%d)\n", err); 1494 return (err); 1495 } 1496 1497 1498 /** 1499 * smsc_ioctl - ioctl function for the device 1500 * @ifp: interface pointer 1501 * @cmd: the ioctl command 1502 * @data: data passed in the ioctl call, typically a pointer to struct ifreq. 1503 * 1504 * The ioctl routine is overridden to detect change requests for the H/W 1505 * checksum capabilities. 1506 * 1507 * RETURNS: 1508 * 0 on success and an error code on failure. 1509 */ 1510 static int 1511 smsc_ioctl(struct ifnet *ifp, u_long cmd, caddr_t data) 1512 { 1513 struct usb_ether *ue = ifp->if_softc; 1514 struct smsc_softc *sc; 1515 struct ifreq *ifr; 1516 int rc; 1517 int mask; 1518 int reinit; 1519 1520 if (cmd == SIOCSIFCAP) { 1521 1522 sc = uether_getsc(ue); 1523 ifr = (struct ifreq *)data; 1524 1525 SMSC_LOCK(sc); 1526 1527 rc = 0; 1528 reinit = 0; 1529 1530 mask = ifr->ifr_reqcap ^ ifp->if_capenable; 1531 1532 /* Modify the RX CSUM enable bits */ 1533 if ((mask & IFCAP_RXCSUM) != 0 && 1534 (ifp->if_capabilities & IFCAP_RXCSUM) != 0) { 1535 ifp->if_capenable ^= IFCAP_RXCSUM; 1536 1537 if (ifp->if_drv_flags & IFF_DRV_RUNNING) { 1538 ifp->if_drv_flags &= ~IFF_DRV_RUNNING; 1539 reinit = 1; 1540 } 1541 } 1542 1543 SMSC_UNLOCK(sc); 1544 if (reinit) 1545 #if __FreeBSD_version > 1000000 1546 uether_init(ue); 1547 #else 1548 ifp->if_init(ue); 1549 #endif 1550 1551 } else { 1552 rc = uether_ioctl(ifp, cmd, data); 1553 } 1554 1555 return (rc); 1556 } 1557 1558 #ifdef FDT 1559 static phandle_t 1560 smsc_fdt_find_eth_node(phandle_t start) 1561 { 1562 phandle_t child, node; 1563 1564 /* Traverse through entire tree to find usb ethernet nodes. */ 1565 for (node = OF_child(start); node != 0; node = OF_peer(node)) { 1566 if (fdt_is_compatible(node, "net,ethernet") && 1567 fdt_is_compatible(node, "usb,device")) 1568 return (node); 1569 child = smsc_fdt_find_eth_node(node); 1570 if (child != 0) 1571 return (child); 1572 } 1573 1574 return (0); 1575 } 1576 1577 /** 1578 * Get MAC address from FDT blob. Firmware or loader should fill 1579 * mac-address or local-mac-address property. Returns 0 if MAC address 1580 * obtained, error code otherwise. 1581 */ 1582 static int 1583 smsc_fdt_find_mac(unsigned char *mac) 1584 { 1585 phandle_t node, root; 1586 int len; 1587 1588 root = OF_finddevice("/"); 1589 node = smsc_fdt_find_eth_node(root); 1590 if (node != 0) { 1591 1592 /* Check if there is property */ 1593 if ((len = OF_getproplen(node, "local-mac-address")) > 0) { 1594 if (len != ETHER_ADDR_LEN) 1595 return (EINVAL); 1596 1597 OF_getprop(node, "local-mac-address", mac, 1598 ETHER_ADDR_LEN); 1599 return (0); 1600 } 1601 1602 if ((len = OF_getproplen(node, "mac-address")) > 0) { 1603 if (len != ETHER_ADDR_LEN) 1604 return (EINVAL); 1605 1606 OF_getprop(node, "mac-address", mac, 1607 ETHER_ADDR_LEN); 1608 return (0); 1609 } 1610 } 1611 1612 return (ENXIO); 1613 } 1614 #endif 1615 1616 /** 1617 * smsc_attach_post - Called after the driver attached to the USB interface 1618 * @ue: the USB ethernet device 1619 * 1620 * This is where the chip is intialised for the first time. This is different 1621 * from the smsc_init() function in that that one is designed to setup the 1622 * H/W to match the UE settings and can be called after a reset. 1623 * 1624 * 1625 */ 1626 static void 1627 smsc_attach_post(struct usb_ether *ue) 1628 { 1629 struct smsc_softc *sc = uether_getsc(ue); 1630 uint32_t mac_h, mac_l; 1631 int err; 1632 1633 smsc_dbg_printf(sc, "smsc_attach_post\n"); 1634 1635 /* Setup some of the basics */ 1636 sc->sc_phyno = 1; 1637 1638 1639 /* Attempt to get the mac address, if an EEPROM is not attached this 1640 * will just return FF:FF:FF:FF:FF:FF, so in such cases we invent a MAC 1641 * address based on urandom. 1642 */ 1643 memset(sc->sc_ue.ue_eaddr, 0xff, ETHER_ADDR_LEN); 1644 1645 /* Check if there is already a MAC address in the register */ 1646 if ((smsc_read_reg(sc, SMSC_MAC_ADDRL, &mac_l) == 0) && 1647 (smsc_read_reg(sc, SMSC_MAC_ADDRH, &mac_h) == 0)) { 1648 sc->sc_ue.ue_eaddr[5] = (uint8_t)((mac_h >> 8) & 0xff); 1649 sc->sc_ue.ue_eaddr[4] = (uint8_t)((mac_h) & 0xff); 1650 sc->sc_ue.ue_eaddr[3] = (uint8_t)((mac_l >> 24) & 0xff); 1651 sc->sc_ue.ue_eaddr[2] = (uint8_t)((mac_l >> 16) & 0xff); 1652 sc->sc_ue.ue_eaddr[1] = (uint8_t)((mac_l >> 8) & 0xff); 1653 sc->sc_ue.ue_eaddr[0] = (uint8_t)((mac_l) & 0xff); 1654 } 1655 1656 /* MAC address is not set so try to read from EEPROM, if that fails generate 1657 * a random MAC address. 1658 */ 1659 if (!ETHER_IS_VALID(sc->sc_ue.ue_eaddr)) { 1660 1661 err = smsc_eeprom_read(sc, 0x01, sc->sc_ue.ue_eaddr, ETHER_ADDR_LEN); 1662 #ifdef FDT 1663 if ((err != 0) || (!ETHER_IS_VALID(sc->sc_ue.ue_eaddr))) 1664 err = smsc_fdt_find_mac(sc->sc_ue.ue_eaddr); 1665 #endif 1666 if ((err != 0) || (!ETHER_IS_VALID(sc->sc_ue.ue_eaddr))) { 1667 read_random(sc->sc_ue.ue_eaddr, ETHER_ADDR_LEN); 1668 sc->sc_ue.ue_eaddr[0] &= ~0x01; /* unicast */ 1669 sc->sc_ue.ue_eaddr[0] |= 0x02; /* locally administered */ 1670 } 1671 } 1672 1673 /* Initialise the chip for the first time */ 1674 smsc_chip_init(sc); 1675 } 1676 1677 1678 /** 1679 * smsc_attach_post_sub - Called after the driver attached to the USB interface 1680 * @ue: the USB ethernet device 1681 * 1682 * Most of this is boilerplate code and copied from the base USB ethernet 1683 * driver. It has been overriden so that we can indicate to the system that 1684 * the chip supports H/W checksumming. 1685 * 1686 * RETURNS: 1687 * Returns 0 on success or a negative error code. 1688 */ 1689 #if __FreeBSD_version > 1000000 1690 static int 1691 smsc_attach_post_sub(struct usb_ether *ue) 1692 { 1693 struct smsc_softc *sc; 1694 struct ifnet *ifp; 1695 int error; 1696 1697 sc = uether_getsc(ue); 1698 ifp = ue->ue_ifp; 1699 ifp->if_flags = IFF_BROADCAST | IFF_SIMPLEX | IFF_MULTICAST; 1700 ifp->if_start = uether_start; 1701 ifp->if_ioctl = smsc_ioctl; 1702 ifp->if_init = uether_init; 1703 IFQ_SET_MAXLEN(&ifp->if_snd, ifqmaxlen); 1704 ifp->if_snd.ifq_drv_maxlen = ifqmaxlen; 1705 IFQ_SET_READY(&ifp->if_snd); 1706 1707 /* The chip supports TCP/UDP checksum offloading on TX and RX paths, however 1708 * currently only RX checksum is supported in the driver (see top of file). 1709 */ 1710 ifp->if_capabilities |= IFCAP_RXCSUM; 1711 ifp->if_hwassist = 0; 1712 1713 /* TX checksuming is disabled (for now?) 1714 ifp->if_capabilities |= IFCAP_TXCSUM; 1715 ifp->if_capenable |= IFCAP_TXCSUM; 1716 ifp->if_hwassist = CSUM_TCP | CSUM_UDP; 1717 */ 1718 1719 ifp->if_capenable = ifp->if_capabilities; 1720 1721 mtx_lock(&Giant); 1722 error = mii_attach(ue->ue_dev, &ue->ue_miibus, ifp, 1723 uether_ifmedia_upd, ue->ue_methods->ue_mii_sts, 1724 BMSR_DEFCAPMASK, sc->sc_phyno, MII_OFFSET_ANY, 0); 1725 mtx_unlock(&Giant); 1726 1727 return (error); 1728 } 1729 #endif /* __FreeBSD_version > 1000000 */ 1730 1731 1732 /** 1733 * smsc_probe - Probe the interface. 1734 * @dev: smsc device handle 1735 * 1736 * Checks if the device is a match for this driver. 1737 * 1738 * RETURNS: 1739 * Returns 0 on success or an error code on failure. 1740 */ 1741 static int 1742 smsc_probe(device_t dev) 1743 { 1744 struct usb_attach_arg *uaa = device_get_ivars(dev); 1745 1746 if (uaa->usb_mode != USB_MODE_HOST) 1747 return (ENXIO); 1748 if (uaa->info.bConfigIndex != SMSC_CONFIG_INDEX) 1749 return (ENXIO); 1750 if (uaa->info.bIfaceIndex != SMSC_IFACE_IDX) 1751 return (ENXIO); 1752 1753 return (usbd_lookup_id_by_uaa(smsc_devs, sizeof(smsc_devs), uaa)); 1754 } 1755 1756 1757 /** 1758 * smsc_attach - Attach the interface. 1759 * @dev: smsc device handle 1760 * 1761 * Allocate softc structures, do ifmedia setup and ethernet/BPF attach. 1762 * 1763 * RETURNS: 1764 * Returns 0 on success or a negative error code. 1765 */ 1766 static int 1767 smsc_attach(device_t dev) 1768 { 1769 struct usb_attach_arg *uaa = device_get_ivars(dev); 1770 struct smsc_softc *sc = device_get_softc(dev); 1771 struct usb_ether *ue = &sc->sc_ue; 1772 uint8_t iface_index; 1773 int err; 1774 1775 sc->sc_flags = USB_GET_DRIVER_INFO(uaa); 1776 1777 device_set_usb_desc(dev); 1778 1779 mtx_init(&sc->sc_mtx, device_get_nameunit(dev), NULL, MTX_DEF); 1780 1781 /* Setup the endpoints for the SMSC LAN95xx device(s) */ 1782 iface_index = SMSC_IFACE_IDX; 1783 err = usbd_transfer_setup(uaa->device, &iface_index, sc->sc_xfer, 1784 smsc_config, SMSC_N_TRANSFER, sc, &sc->sc_mtx); 1785 if (err) { 1786 device_printf(dev, "error: allocating USB transfers failed\n"); 1787 goto detach; 1788 } 1789 1790 ue->ue_sc = sc; 1791 ue->ue_dev = dev; 1792 ue->ue_udev = uaa->device; 1793 ue->ue_mtx = &sc->sc_mtx; 1794 ue->ue_methods = &smsc_ue_methods; 1795 1796 err = uether_ifattach(ue); 1797 if (err) { 1798 device_printf(dev, "error: could not attach interface\n"); 1799 goto detach; 1800 } 1801 return (0); /* success */ 1802 1803 detach: 1804 smsc_detach(dev); 1805 return (ENXIO); /* failure */ 1806 } 1807 1808 /** 1809 * smsc_detach - Detach the interface. 1810 * @dev: smsc device handle 1811 * 1812 * RETURNS: 1813 * Returns 0. 1814 */ 1815 static int 1816 smsc_detach(device_t dev) 1817 { 1818 struct smsc_softc *sc = device_get_softc(dev); 1819 struct usb_ether *ue = &sc->sc_ue; 1820 1821 usbd_transfer_unsetup(sc->sc_xfer, SMSC_N_TRANSFER); 1822 uether_ifdetach(ue); 1823 mtx_destroy(&sc->sc_mtx); 1824 1825 return (0); 1826 } 1827 1828 static device_method_t smsc_methods[] = { 1829 /* Device interface */ 1830 DEVMETHOD(device_probe, smsc_probe), 1831 DEVMETHOD(device_attach, smsc_attach), 1832 DEVMETHOD(device_detach, smsc_detach), 1833 1834 /* bus interface */ 1835 DEVMETHOD(bus_print_child, bus_generic_print_child), 1836 DEVMETHOD(bus_driver_added, bus_generic_driver_added), 1837 1838 /* MII interface */ 1839 DEVMETHOD(miibus_readreg, smsc_miibus_readreg), 1840 DEVMETHOD(miibus_writereg, smsc_miibus_writereg), 1841 DEVMETHOD(miibus_statchg, smsc_miibus_statchg), 1842 1843 DEVMETHOD_END 1844 }; 1845 1846 static driver_t smsc_driver = { 1847 .name = "smsc", 1848 .methods = smsc_methods, 1849 .size = sizeof(struct smsc_softc), 1850 }; 1851 1852 static devclass_t smsc_devclass; 1853 1854 DRIVER_MODULE(smsc, uhub, smsc_driver, smsc_devclass, NULL, 0); 1855 DRIVER_MODULE(miibus, smsc, miibus_driver, miibus_devclass, 0, 0); 1856 MODULE_DEPEND(smsc, uether, 1, 1, 1); 1857 MODULE_DEPEND(smsc, usb, 1, 1, 1); 1858 MODULE_DEPEND(smsc, ether, 1, 1, 1); 1859 MODULE_DEPEND(smsc, miibus, 1, 1, 1); 1860 MODULE_VERSION(smsc, 1); 1861