1 /*- 2 * SPDX-License-Identifier: BSD-4-Clause 3 * 4 * Copyright (c) 1997, 1998, 1999, 2000 5 * Bill Paul <wpaul@ee.columbia.edu>. All rights reserved. 6 * 7 * Copyright (c) 2006 8 * Alfred Perlstein <alfred@FreeBSD.org>. All rights reserved. 9 * 10 * Redistribution and use in source and binary forms, with or without 11 * modification, are permitted provided that the following conditions 12 * are met: 13 * 1. Redistributions of source code must retain the above copyright 14 * notice, this list of conditions and the following disclaimer. 15 * 2. Redistributions in binary form must reproduce the above copyright 16 * notice, this list of conditions and the following disclaimer in the 17 * documentation and/or other materials provided with the distribution. 18 * 3. All advertising materials mentioning features or use of this software 19 * must display the following acknowledgement: 20 * This product includes software developed by Bill Paul. 21 * 4. Neither the name of the author nor the names of any co-contributors 22 * may be used to endorse or promote products derived from this software 23 * without specific prior written permission. 24 * 25 * THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND 26 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 27 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 28 * ARE DISCLAIMED. IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD 29 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 30 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 31 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 32 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 33 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 34 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF 35 * THE POSSIBILITY OF SUCH DAMAGE. 36 */ 37 38 #include <sys/cdefs.h> 39 __FBSDID("$FreeBSD$"); 40 41 /* 42 * ADMtek AN986 Pegasus and AN8511 Pegasus II USB to ethernet driver. 43 * Datasheet is available from http://www.admtek.com.tw. 44 * 45 * Written by Bill Paul <wpaul@ee.columbia.edu> 46 * Electrical Engineering Department 47 * Columbia University, New York City 48 * 49 * SMP locking by Alfred Perlstein <alfred@FreeBSD.org>. 50 * RED Inc. 51 */ 52 53 /* 54 * The Pegasus chip uses four USB "endpoints" to provide 10/100 ethernet 55 * support: the control endpoint for reading/writing registers, burst 56 * read endpoint for packet reception, burst write for packet transmission 57 * and one for "interrupts." The chip uses the same RX filter scheme 58 * as the other ADMtek ethernet parts: one perfect filter entry for the 59 * the station address and a 64-bit multicast hash table. The chip supports 60 * both MII and HomePNA attachments. 61 * 62 * Since the maximum data transfer speed of USB is supposed to be 12Mbps, 63 * you're never really going to get 100Mbps speeds from this device. I 64 * think the idea is to allow the device to connect to 10 or 100Mbps 65 * networks, not necessarily to provide 100Mbps performance. Also, since 66 * the controller uses an external PHY chip, it's possible that board 67 * designers might simply choose a 10Mbps PHY. 68 * 69 * Registers are accessed using uether_do_request(). Packet 70 * transfers are done using usbd_transfer() and friends. 71 */ 72 73 #include <sys/stdint.h> 74 #include <sys/stddef.h> 75 #include <sys/param.h> 76 #include <sys/queue.h> 77 #include <sys/types.h> 78 #include <sys/systm.h> 79 #include <sys/socket.h> 80 #include <sys/kernel.h> 81 #include <sys/bus.h> 82 #include <sys/module.h> 83 #include <sys/lock.h> 84 #include <sys/mutex.h> 85 #include <sys/condvar.h> 86 #include <sys/sysctl.h> 87 #include <sys/sx.h> 88 #include <sys/unistd.h> 89 #include <sys/callout.h> 90 #include <sys/malloc.h> 91 #include <sys/priv.h> 92 93 #include <net/if.h> 94 #include <net/if_var.h> 95 #include <net/if_media.h> 96 97 #include <dev/mii/mii.h> 98 #include <dev/mii/miivar.h> 99 100 #include <dev/usb/usb.h> 101 #include <dev/usb/usbdi.h> 102 #include <dev/usb/usbdi_util.h> 103 #include "usbdevs.h" 104 105 #define USB_DEBUG_VAR aue_debug 106 #include <dev/usb/usb_debug.h> 107 #include <dev/usb/usb_process.h> 108 109 #include <dev/usb/net/usb_ethernet.h> 110 #include <dev/usb/net/if_auereg.h> 111 112 #include "miibus_if.h" 113 114 #ifdef USB_DEBUG 115 static int aue_debug = 0; 116 117 static SYSCTL_NODE(_hw_usb, OID_AUTO, aue, CTLFLAG_RW, 0, "USB aue"); 118 SYSCTL_INT(_hw_usb_aue, OID_AUTO, debug, CTLFLAG_RWTUN, &aue_debug, 0, 119 "Debug level"); 120 #endif 121 122 /* 123 * Various supported device vendors/products. 124 */ 125 static const STRUCT_USB_HOST_ID aue_devs[] = { 126 #define AUE_DEV(v,p,i) { USB_VPI(USB_VENDOR_##v, USB_PRODUCT_##v##_##p, i) } 127 AUE_DEV(3COM, 3C460B, AUE_FLAG_PII), 128 AUE_DEV(ABOCOM, DSB650TX_PNA, 0), 129 AUE_DEV(ABOCOM, UFE1000, AUE_FLAG_LSYS), 130 AUE_DEV(ABOCOM, XX10, 0), 131 AUE_DEV(ABOCOM, XX1, AUE_FLAG_PNA | AUE_FLAG_PII), 132 AUE_DEV(ABOCOM, XX2, AUE_FLAG_PII), 133 AUE_DEV(ABOCOM, XX4, AUE_FLAG_PNA), 134 AUE_DEV(ABOCOM, XX5, AUE_FLAG_PNA), 135 AUE_DEV(ABOCOM, XX6, AUE_FLAG_PII), 136 AUE_DEV(ABOCOM, XX7, AUE_FLAG_PII), 137 AUE_DEV(ABOCOM, XX8, AUE_FLAG_PII), 138 AUE_DEV(ABOCOM, XX9, AUE_FLAG_PNA), 139 AUE_DEV(ACCTON, SS1001, AUE_FLAG_PII), 140 AUE_DEV(ACCTON, USB320_EC, 0), 141 AUE_DEV(ADMTEK, PEGASUSII_2, AUE_FLAG_PII), 142 AUE_DEV(ADMTEK, PEGASUSII_3, AUE_FLAG_PII), 143 AUE_DEV(ADMTEK, PEGASUSII_4, AUE_FLAG_PII), 144 AUE_DEV(ADMTEK, PEGASUSII, AUE_FLAG_PII), 145 AUE_DEV(ADMTEK, PEGASUS, AUE_FLAG_PNA | AUE_FLAG_DUAL_PHY), 146 AUE_DEV(AEI, FASTETHERNET, AUE_FLAG_PII), 147 AUE_DEV(ALLIEDTELESYN, ATUSB100, AUE_FLAG_PII), 148 AUE_DEV(ATEN, UC110T, AUE_FLAG_PII), 149 AUE_DEV(BELKIN, USB2LAN, AUE_FLAG_PII), 150 AUE_DEV(BILLIONTON, USB100, 0), 151 AUE_DEV(BILLIONTON, USBE100, AUE_FLAG_PII), 152 AUE_DEV(BILLIONTON, USBEL100, 0), 153 AUE_DEV(BILLIONTON, USBLP100, AUE_FLAG_PNA), 154 AUE_DEV(COREGA, FETHER_USB_TXS, AUE_FLAG_PII), 155 AUE_DEV(COREGA, FETHER_USB_TX, 0), 156 AUE_DEV(DLINK, DSB650TX1, AUE_FLAG_LSYS), 157 AUE_DEV(DLINK, DSB650TX2, AUE_FLAG_LSYS | AUE_FLAG_PII), 158 AUE_DEV(DLINK, DSB650TX3, AUE_FLAG_LSYS | AUE_FLAG_PII), 159 AUE_DEV(DLINK, DSB650TX4, AUE_FLAG_LSYS | AUE_FLAG_PII), 160 AUE_DEV(DLINK, DSB650TX_PNA, AUE_FLAG_PNA), 161 AUE_DEV(DLINK, DSB650TX, AUE_FLAG_LSYS), 162 AUE_DEV(DLINK, DSB650, AUE_FLAG_LSYS), 163 AUE_DEV(ELCON, PLAN, AUE_FLAG_PNA | AUE_FLAG_PII), 164 AUE_DEV(ELECOM, LDUSB20, AUE_FLAG_PII), 165 AUE_DEV(ELECOM, LDUSBLTX, AUE_FLAG_PII), 166 AUE_DEV(ELECOM, LDUSBTX0, 0), 167 AUE_DEV(ELECOM, LDUSBTX1, AUE_FLAG_LSYS), 168 AUE_DEV(ELECOM, LDUSBTX2, 0), 169 AUE_DEV(ELECOM, LDUSBTX3, AUE_FLAG_LSYS), 170 AUE_DEV(ELSA, USB2ETHERNET, 0), 171 AUE_DEV(GIGABYTE, GNBR402W, 0), 172 AUE_DEV(HAWKING, UF100, AUE_FLAG_PII), 173 AUE_DEV(HP, HN210E, AUE_FLAG_PII), 174 AUE_DEV(IODATA, USBETTXS, AUE_FLAG_PII), 175 AUE_DEV(IODATA, USBETTX, 0), 176 AUE_DEV(KINGSTON, KNU101TX, 0), 177 AUE_DEV(LINKSYS, USB100H1, AUE_FLAG_LSYS | AUE_FLAG_PNA), 178 AUE_DEV(LINKSYS, USB100TX, AUE_FLAG_LSYS), 179 AUE_DEV(LINKSYS, USB10TA, AUE_FLAG_LSYS), 180 AUE_DEV(LINKSYS, USB10TX1, AUE_FLAG_LSYS | AUE_FLAG_PII), 181 AUE_DEV(LINKSYS, USB10TX2, AUE_FLAG_LSYS | AUE_FLAG_PII), 182 AUE_DEV(LINKSYS, USB10T, AUE_FLAG_LSYS), 183 AUE_DEV(MELCO, LUA2TX5, AUE_FLAG_PII), 184 AUE_DEV(MELCO, LUATX1, 0), 185 AUE_DEV(MELCO, LUATX5, 0), 186 AUE_DEV(MICROSOFT, MN110, AUE_FLAG_PII), 187 AUE_DEV(NETGEAR, FA101, AUE_FLAG_PII), 188 AUE_DEV(SIEMENS, SPEEDSTREAM, AUE_FLAG_PII), 189 AUE_DEV(SIIG2, USBTOETHER, AUE_FLAG_PII), 190 AUE_DEV(SMARTBRIDGES, SMARTNIC, AUE_FLAG_PII), 191 AUE_DEV(SMC, 2202USB, 0), 192 AUE_DEV(SMC, 2206USB, AUE_FLAG_PII), 193 AUE_DEV(SOHOWARE, NUB100, 0), 194 AUE_DEV(SOHOWARE, NUB110, AUE_FLAG_PII), 195 #undef AUE_DEV 196 }; 197 198 /* prototypes */ 199 200 static device_probe_t aue_probe; 201 static device_attach_t aue_attach; 202 static device_detach_t aue_detach; 203 static miibus_readreg_t aue_miibus_readreg; 204 static miibus_writereg_t aue_miibus_writereg; 205 static miibus_statchg_t aue_miibus_statchg; 206 207 static usb_callback_t aue_intr_callback; 208 static usb_callback_t aue_bulk_read_callback; 209 static usb_callback_t aue_bulk_write_callback; 210 211 static uether_fn_t aue_attach_post; 212 static uether_fn_t aue_init; 213 static uether_fn_t aue_stop; 214 static uether_fn_t aue_start; 215 static uether_fn_t aue_tick; 216 static uether_fn_t aue_setmulti; 217 static uether_fn_t aue_setpromisc; 218 219 static uint8_t aue_csr_read_1(struct aue_softc *, uint16_t); 220 static uint16_t aue_csr_read_2(struct aue_softc *, uint16_t); 221 static void aue_csr_write_1(struct aue_softc *, uint16_t, uint8_t); 222 static void aue_csr_write_2(struct aue_softc *, uint16_t, uint16_t); 223 static uint16_t aue_eeprom_getword(struct aue_softc *, int); 224 static void aue_reset(struct aue_softc *); 225 static void aue_reset_pegasus_II(struct aue_softc *); 226 227 static int aue_ifmedia_upd(struct ifnet *); 228 static void aue_ifmedia_sts(struct ifnet *, struct ifmediareq *); 229 230 static const struct usb_config aue_config[AUE_N_TRANSFER] = { 231 232 [AUE_BULK_DT_WR] = { 233 .type = UE_BULK, 234 .endpoint = UE_ADDR_ANY, 235 .direction = UE_DIR_OUT, 236 .bufsize = (MCLBYTES + 2), 237 .flags = {.pipe_bof = 1,.force_short_xfer = 1,}, 238 .callback = aue_bulk_write_callback, 239 .timeout = 10000, /* 10 seconds */ 240 }, 241 242 [AUE_BULK_DT_RD] = { 243 .type = UE_BULK, 244 .endpoint = UE_ADDR_ANY, 245 .direction = UE_DIR_IN, 246 .bufsize = (MCLBYTES + 4 + ETHER_CRC_LEN), 247 .flags = {.pipe_bof = 1,.short_xfer_ok = 1,}, 248 .callback = aue_bulk_read_callback, 249 }, 250 251 [AUE_INTR_DT_RD] = { 252 .type = UE_INTERRUPT, 253 .endpoint = UE_ADDR_ANY, 254 .direction = UE_DIR_IN, 255 .flags = {.pipe_bof = 1,.short_xfer_ok = 1,}, 256 .bufsize = 0, /* use wMaxPacketSize */ 257 .callback = aue_intr_callback, 258 }, 259 }; 260 261 static device_method_t aue_methods[] = { 262 /* Device interface */ 263 DEVMETHOD(device_probe, aue_probe), 264 DEVMETHOD(device_attach, aue_attach), 265 DEVMETHOD(device_detach, aue_detach), 266 267 /* MII interface */ 268 DEVMETHOD(miibus_readreg, aue_miibus_readreg), 269 DEVMETHOD(miibus_writereg, aue_miibus_writereg), 270 DEVMETHOD(miibus_statchg, aue_miibus_statchg), 271 272 DEVMETHOD_END 273 }; 274 275 static driver_t aue_driver = { 276 .name = "aue", 277 .methods = aue_methods, 278 .size = sizeof(struct aue_softc) 279 }; 280 281 static devclass_t aue_devclass; 282 283 DRIVER_MODULE(aue, uhub, aue_driver, aue_devclass, NULL, 0); 284 DRIVER_MODULE(miibus, aue, miibus_driver, miibus_devclass, 0, 0); 285 MODULE_DEPEND(aue, uether, 1, 1, 1); 286 MODULE_DEPEND(aue, usb, 1, 1, 1); 287 MODULE_DEPEND(aue, ether, 1, 1, 1); 288 MODULE_DEPEND(aue, miibus, 1, 1, 1); 289 MODULE_VERSION(aue, 1); 290 USB_PNP_HOST_INFO(aue_devs); 291 292 static const struct usb_ether_methods aue_ue_methods = { 293 .ue_attach_post = aue_attach_post, 294 .ue_start = aue_start, 295 .ue_init = aue_init, 296 .ue_stop = aue_stop, 297 .ue_tick = aue_tick, 298 .ue_setmulti = aue_setmulti, 299 .ue_setpromisc = aue_setpromisc, 300 .ue_mii_upd = aue_ifmedia_upd, 301 .ue_mii_sts = aue_ifmedia_sts, 302 }; 303 304 #define AUE_SETBIT(sc, reg, x) \ 305 aue_csr_write_1(sc, reg, aue_csr_read_1(sc, reg) | (x)) 306 307 #define AUE_CLRBIT(sc, reg, x) \ 308 aue_csr_write_1(sc, reg, aue_csr_read_1(sc, reg) & ~(x)) 309 310 static uint8_t 311 aue_csr_read_1(struct aue_softc *sc, uint16_t reg) 312 { 313 struct usb_device_request req; 314 usb_error_t err; 315 uint8_t val; 316 317 req.bmRequestType = UT_READ_VENDOR_DEVICE; 318 req.bRequest = AUE_UR_READREG; 319 USETW(req.wValue, 0); 320 USETW(req.wIndex, reg); 321 USETW(req.wLength, 1); 322 323 err = uether_do_request(&sc->sc_ue, &req, &val, 1000); 324 if (err) 325 return (0); 326 return (val); 327 } 328 329 static uint16_t 330 aue_csr_read_2(struct aue_softc *sc, uint16_t reg) 331 { 332 struct usb_device_request req; 333 usb_error_t err; 334 uint16_t val; 335 336 req.bmRequestType = UT_READ_VENDOR_DEVICE; 337 req.bRequest = AUE_UR_READREG; 338 USETW(req.wValue, 0); 339 USETW(req.wIndex, reg); 340 USETW(req.wLength, 2); 341 342 err = uether_do_request(&sc->sc_ue, &req, &val, 1000); 343 if (err) 344 return (0); 345 return (le16toh(val)); 346 } 347 348 static void 349 aue_csr_write_1(struct aue_softc *sc, uint16_t reg, uint8_t val) 350 { 351 struct usb_device_request req; 352 353 req.bmRequestType = UT_WRITE_VENDOR_DEVICE; 354 req.bRequest = AUE_UR_WRITEREG; 355 req.wValue[0] = val; 356 req.wValue[1] = 0; 357 USETW(req.wIndex, reg); 358 USETW(req.wLength, 1); 359 360 if (uether_do_request(&sc->sc_ue, &req, &val, 1000)) { 361 /* error ignored */ 362 } 363 } 364 365 static void 366 aue_csr_write_2(struct aue_softc *sc, uint16_t reg, uint16_t val) 367 { 368 struct usb_device_request req; 369 370 req.bmRequestType = UT_WRITE_VENDOR_DEVICE; 371 req.bRequest = AUE_UR_WRITEREG; 372 USETW(req.wValue, val); 373 USETW(req.wIndex, reg); 374 USETW(req.wLength, 2); 375 376 val = htole16(val); 377 378 if (uether_do_request(&sc->sc_ue, &req, &val, 1000)) { 379 /* error ignored */ 380 } 381 } 382 383 /* 384 * Read a word of data stored in the EEPROM at address 'addr.' 385 */ 386 static uint16_t 387 aue_eeprom_getword(struct aue_softc *sc, int addr) 388 { 389 int i; 390 391 aue_csr_write_1(sc, AUE_EE_REG, addr); 392 aue_csr_write_1(sc, AUE_EE_CTL, AUE_EECTL_READ); 393 394 for (i = 0; i != AUE_TIMEOUT; i++) { 395 if (aue_csr_read_1(sc, AUE_EE_CTL) & AUE_EECTL_DONE) 396 break; 397 if (uether_pause(&sc->sc_ue, hz / 100)) 398 break; 399 } 400 401 if (i == AUE_TIMEOUT) 402 device_printf(sc->sc_ue.ue_dev, "EEPROM read timed out\n"); 403 404 return (aue_csr_read_2(sc, AUE_EE_DATA)); 405 } 406 407 /* 408 * Read station address(offset 0) from the EEPROM. 409 */ 410 static void 411 aue_read_mac(struct aue_softc *sc, uint8_t *eaddr) 412 { 413 int i, offset; 414 uint16_t word; 415 416 for (i = 0, offset = 0; i < ETHER_ADDR_LEN / 2; i++) { 417 word = aue_eeprom_getword(sc, offset + i); 418 eaddr[i * 2] = (uint8_t)word; 419 eaddr[i * 2 + 1] = (uint8_t)(word >> 8); 420 } 421 } 422 423 static int 424 aue_miibus_readreg(device_t dev, int phy, int reg) 425 { 426 struct aue_softc *sc = device_get_softc(dev); 427 int i, locked; 428 uint16_t val = 0; 429 430 locked = mtx_owned(&sc->sc_mtx); 431 if (!locked) 432 AUE_LOCK(sc); 433 434 /* 435 * The Am79C901 HomePNA PHY actually contains two transceivers: a 1Mbps 436 * HomePNA PHY and a 10Mbps full/half duplex ethernet PHY with NWAY 437 * autoneg. However in the ADMtek adapter, only the 1Mbps PHY is 438 * actually connected to anything, so we ignore the 10Mbps one. It 439 * happens to be configured for MII address 3, so we filter that out. 440 */ 441 if (sc->sc_flags & AUE_FLAG_DUAL_PHY) { 442 if (phy == 3) 443 goto done; 444 #if 0 445 if (phy != 1) 446 goto done; 447 #endif 448 } 449 aue_csr_write_1(sc, AUE_PHY_ADDR, phy); 450 aue_csr_write_1(sc, AUE_PHY_CTL, reg | AUE_PHYCTL_READ); 451 452 for (i = 0; i != AUE_TIMEOUT; i++) { 453 if (aue_csr_read_1(sc, AUE_PHY_CTL) & AUE_PHYCTL_DONE) 454 break; 455 if (uether_pause(&sc->sc_ue, hz / 100)) 456 break; 457 } 458 459 if (i == AUE_TIMEOUT) 460 device_printf(sc->sc_ue.ue_dev, "MII read timed out\n"); 461 462 val = aue_csr_read_2(sc, AUE_PHY_DATA); 463 464 done: 465 if (!locked) 466 AUE_UNLOCK(sc); 467 return (val); 468 } 469 470 static int 471 aue_miibus_writereg(device_t dev, int phy, int reg, int data) 472 { 473 struct aue_softc *sc = device_get_softc(dev); 474 int i; 475 int locked; 476 477 if (phy == 3) 478 return (0); 479 480 locked = mtx_owned(&sc->sc_mtx); 481 if (!locked) 482 AUE_LOCK(sc); 483 484 aue_csr_write_2(sc, AUE_PHY_DATA, data); 485 aue_csr_write_1(sc, AUE_PHY_ADDR, phy); 486 aue_csr_write_1(sc, AUE_PHY_CTL, reg | AUE_PHYCTL_WRITE); 487 488 for (i = 0; i != AUE_TIMEOUT; i++) { 489 if (aue_csr_read_1(sc, AUE_PHY_CTL) & AUE_PHYCTL_DONE) 490 break; 491 if (uether_pause(&sc->sc_ue, hz / 100)) 492 break; 493 } 494 495 if (i == AUE_TIMEOUT) 496 device_printf(sc->sc_ue.ue_dev, "MII write timed out\n"); 497 498 if (!locked) 499 AUE_UNLOCK(sc); 500 return (0); 501 } 502 503 static void 504 aue_miibus_statchg(device_t dev) 505 { 506 struct aue_softc *sc = device_get_softc(dev); 507 struct mii_data *mii = GET_MII(sc); 508 int locked; 509 510 locked = mtx_owned(&sc->sc_mtx); 511 if (!locked) 512 AUE_LOCK(sc); 513 514 AUE_CLRBIT(sc, AUE_CTL0, AUE_CTL0_RX_ENB | AUE_CTL0_TX_ENB); 515 if (IFM_SUBTYPE(mii->mii_media_active) == IFM_100_TX) 516 AUE_SETBIT(sc, AUE_CTL1, AUE_CTL1_SPEEDSEL); 517 else 518 AUE_CLRBIT(sc, AUE_CTL1, AUE_CTL1_SPEEDSEL); 519 520 if ((mii->mii_media_active & IFM_GMASK) == IFM_FDX) 521 AUE_SETBIT(sc, AUE_CTL1, AUE_CTL1_DUPLEX); 522 else 523 AUE_CLRBIT(sc, AUE_CTL1, AUE_CTL1_DUPLEX); 524 525 AUE_SETBIT(sc, AUE_CTL0, AUE_CTL0_RX_ENB | AUE_CTL0_TX_ENB); 526 527 /* 528 * Set the LED modes on the LinkSys adapter. 529 * This turns on the 'dual link LED' bin in the auxmode 530 * register of the Broadcom PHY. 531 */ 532 if (sc->sc_flags & AUE_FLAG_LSYS) { 533 uint16_t auxmode; 534 535 auxmode = aue_miibus_readreg(dev, 0, 0x1b); 536 aue_miibus_writereg(dev, 0, 0x1b, auxmode | 0x04); 537 } 538 if (!locked) 539 AUE_UNLOCK(sc); 540 } 541 542 #define AUE_BITS 6 543 static u_int 544 aue_hash_maddr(void *arg, struct sockaddr_dl *sdl, u_int cnt) 545 { 546 uint8_t *hashtbl = arg; 547 uint32_t h; 548 549 h = ether_crc32_le(LLADDR(sdl), ETHER_ADDR_LEN) & ((1 << AUE_BITS) - 1); 550 hashtbl[(h >> 3)] |= 1 << (h & 0x7); 551 552 return (1); 553 } 554 555 static void 556 aue_setmulti(struct usb_ether *ue) 557 { 558 struct aue_softc *sc = uether_getsc(ue); 559 struct ifnet *ifp = uether_getifp(ue); 560 uint32_t i; 561 uint8_t hashtbl[8] = { 0, 0, 0, 0, 0, 0, 0, 0 }; 562 563 AUE_LOCK_ASSERT(sc, MA_OWNED); 564 565 if (ifp->if_flags & IFF_ALLMULTI || ifp->if_flags & IFF_PROMISC) { 566 AUE_SETBIT(sc, AUE_CTL0, AUE_CTL0_ALLMULTI); 567 return; 568 } 569 570 AUE_CLRBIT(sc, AUE_CTL0, AUE_CTL0_ALLMULTI); 571 572 /* now program new ones */ 573 if_foreach_llmaddr(ifp, aue_hash_maddr, hashtbl); 574 575 /* write the hashtable */ 576 for (i = 0; i != 8; i++) 577 aue_csr_write_1(sc, AUE_MAR0 + i, hashtbl[i]); 578 } 579 580 static void 581 aue_reset_pegasus_II(struct aue_softc *sc) 582 { 583 /* Magic constants taken from Linux driver. */ 584 aue_csr_write_1(sc, AUE_REG_1D, 0); 585 aue_csr_write_1(sc, AUE_REG_7B, 2); 586 #if 0 587 if ((sc->sc_flags & HAS_HOME_PNA) && mii_mode) 588 aue_csr_write_1(sc, AUE_REG_81, 6); 589 else 590 #endif 591 aue_csr_write_1(sc, AUE_REG_81, 2); 592 } 593 594 static void 595 aue_reset(struct aue_softc *sc) 596 { 597 int i; 598 599 AUE_SETBIT(sc, AUE_CTL1, AUE_CTL1_RESETMAC); 600 601 for (i = 0; i != AUE_TIMEOUT; i++) { 602 if (!(aue_csr_read_1(sc, AUE_CTL1) & AUE_CTL1_RESETMAC)) 603 break; 604 if (uether_pause(&sc->sc_ue, hz / 100)) 605 break; 606 } 607 608 if (i == AUE_TIMEOUT) 609 device_printf(sc->sc_ue.ue_dev, "reset failed\n"); 610 611 /* 612 * The PHY(s) attached to the Pegasus chip may be held 613 * in reset until we flip on the GPIO outputs. Make sure 614 * to set the GPIO pins high so that the PHY(s) will 615 * be enabled. 616 * 617 * NOTE: We used to force all of the GPIO pins low first and then 618 * enable the ones we want. This has been changed to better 619 * match the ADMtek's reference design to avoid setting the 620 * power-down configuration line of the PHY at the same time 621 * it is reset. 622 */ 623 aue_csr_write_1(sc, AUE_GPIO0, AUE_GPIO_SEL0|AUE_GPIO_SEL1); 624 aue_csr_write_1(sc, AUE_GPIO0, AUE_GPIO_SEL0|AUE_GPIO_SEL1|AUE_GPIO_OUT0); 625 626 if (sc->sc_flags & AUE_FLAG_LSYS) { 627 /* Grrr. LinkSys has to be different from everyone else. */ 628 aue_csr_write_1(sc, AUE_GPIO0, AUE_GPIO_SEL0|AUE_GPIO_SEL1); 629 aue_csr_write_1(sc, AUE_GPIO0, 630 AUE_GPIO_SEL0|AUE_GPIO_SEL1|AUE_GPIO_OUT0); 631 } 632 if (sc->sc_flags & AUE_FLAG_PII) 633 aue_reset_pegasus_II(sc); 634 635 /* Wait a little while for the chip to get its brains in order: */ 636 uether_pause(&sc->sc_ue, hz / 100); 637 } 638 639 static void 640 aue_attach_post(struct usb_ether *ue) 641 { 642 struct aue_softc *sc = uether_getsc(ue); 643 644 /* reset the adapter */ 645 aue_reset(sc); 646 647 /* get station address from the EEPROM */ 648 aue_read_mac(sc, ue->ue_eaddr); 649 } 650 651 /* 652 * Probe for a Pegasus chip. 653 */ 654 static int 655 aue_probe(device_t dev) 656 { 657 struct usb_attach_arg *uaa = device_get_ivars(dev); 658 659 if (uaa->usb_mode != USB_MODE_HOST) 660 return (ENXIO); 661 if (uaa->info.bConfigIndex != AUE_CONFIG_INDEX) 662 return (ENXIO); 663 if (uaa->info.bIfaceIndex != AUE_IFACE_IDX) 664 return (ENXIO); 665 /* 666 * Belkin USB Bluetooth dongles of the F8T012xx1 model series conflict 667 * with older Belkin USB2LAN adapters. Skip if_aue if we detect one of 668 * the devices that look like Bluetooth adapters. 669 */ 670 if (uaa->info.idVendor == USB_VENDOR_BELKIN && 671 uaa->info.idProduct == USB_PRODUCT_BELKIN_F8T012 && 672 uaa->info.bcdDevice == 0x0413) 673 return (ENXIO); 674 675 return (usbd_lookup_id_by_uaa(aue_devs, sizeof(aue_devs), uaa)); 676 } 677 678 /* 679 * Attach the interface. Allocate softc structures, do ifmedia 680 * setup and ethernet/BPF attach. 681 */ 682 static int 683 aue_attach(device_t dev) 684 { 685 struct usb_attach_arg *uaa = device_get_ivars(dev); 686 struct aue_softc *sc = device_get_softc(dev); 687 struct usb_ether *ue = &sc->sc_ue; 688 uint8_t iface_index; 689 int error; 690 691 sc->sc_flags = USB_GET_DRIVER_INFO(uaa); 692 693 if (uaa->info.bcdDevice >= 0x0201) { 694 /* XXX currently undocumented */ 695 sc->sc_flags |= AUE_FLAG_VER_2; 696 } 697 698 device_set_usb_desc(dev); 699 mtx_init(&sc->sc_mtx, device_get_nameunit(dev), NULL, MTX_DEF); 700 701 iface_index = AUE_IFACE_IDX; 702 error = usbd_transfer_setup(uaa->device, &iface_index, 703 sc->sc_xfer, aue_config, AUE_N_TRANSFER, 704 sc, &sc->sc_mtx); 705 if (error) { 706 device_printf(dev, "allocating USB transfers failed\n"); 707 goto detach; 708 } 709 710 ue->ue_sc = sc; 711 ue->ue_dev = dev; 712 ue->ue_udev = uaa->device; 713 ue->ue_mtx = &sc->sc_mtx; 714 ue->ue_methods = &aue_ue_methods; 715 716 error = uether_ifattach(ue); 717 if (error) { 718 device_printf(dev, "could not attach interface\n"); 719 goto detach; 720 } 721 return (0); /* success */ 722 723 detach: 724 aue_detach(dev); 725 return (ENXIO); /* failure */ 726 } 727 728 static int 729 aue_detach(device_t dev) 730 { 731 struct aue_softc *sc = device_get_softc(dev); 732 struct usb_ether *ue = &sc->sc_ue; 733 734 usbd_transfer_unsetup(sc->sc_xfer, AUE_N_TRANSFER); 735 uether_ifdetach(ue); 736 mtx_destroy(&sc->sc_mtx); 737 738 return (0); 739 } 740 741 static void 742 aue_intr_callback(struct usb_xfer *xfer, usb_error_t error) 743 { 744 struct aue_softc *sc = usbd_xfer_softc(xfer); 745 struct ifnet *ifp = uether_getifp(&sc->sc_ue); 746 struct aue_intrpkt pkt; 747 struct usb_page_cache *pc; 748 int actlen; 749 750 usbd_xfer_status(xfer, &actlen, NULL, NULL, NULL); 751 752 switch (USB_GET_STATE(xfer)) { 753 case USB_ST_TRANSFERRED: 754 755 if ((ifp->if_drv_flags & IFF_DRV_RUNNING) && 756 actlen >= (int)sizeof(pkt)) { 757 758 pc = usbd_xfer_get_frame(xfer, 0); 759 usbd_copy_out(pc, 0, &pkt, sizeof(pkt)); 760 761 if (pkt.aue_txstat0) 762 if_inc_counter(ifp, IFCOUNTER_OERRORS, 1); 763 if (pkt.aue_txstat0 & (AUE_TXSTAT0_LATECOLL | 764 AUE_TXSTAT0_EXCESSCOLL)) 765 if_inc_counter(ifp, IFCOUNTER_COLLISIONS, 1); 766 } 767 /* FALLTHROUGH */ 768 case USB_ST_SETUP: 769 tr_setup: 770 usbd_xfer_set_frame_len(xfer, 0, usbd_xfer_max_len(xfer)); 771 usbd_transfer_submit(xfer); 772 return; 773 774 default: /* Error */ 775 if (error != USB_ERR_CANCELLED) { 776 /* try to clear stall first */ 777 usbd_xfer_set_stall(xfer); 778 goto tr_setup; 779 } 780 return; 781 } 782 } 783 784 static void 785 aue_bulk_read_callback(struct usb_xfer *xfer, usb_error_t error) 786 { 787 struct aue_softc *sc = usbd_xfer_softc(xfer); 788 struct usb_ether *ue = &sc->sc_ue; 789 struct ifnet *ifp = uether_getifp(ue); 790 struct aue_rxpkt stat; 791 struct usb_page_cache *pc; 792 int actlen; 793 794 usbd_xfer_status(xfer, &actlen, NULL, NULL, NULL); 795 pc = usbd_xfer_get_frame(xfer, 0); 796 797 switch (USB_GET_STATE(xfer)) { 798 case USB_ST_TRANSFERRED: 799 DPRINTFN(11, "received %d bytes\n", actlen); 800 801 if (sc->sc_flags & AUE_FLAG_VER_2) { 802 803 if (actlen == 0) { 804 if_inc_counter(ifp, IFCOUNTER_IERRORS, 1); 805 goto tr_setup; 806 } 807 } else { 808 809 if (actlen <= (int)(sizeof(stat) + ETHER_CRC_LEN)) { 810 if_inc_counter(ifp, IFCOUNTER_IERRORS, 1); 811 goto tr_setup; 812 } 813 usbd_copy_out(pc, actlen - sizeof(stat), &stat, 814 sizeof(stat)); 815 816 /* 817 * turn off all the non-error bits in the rx status 818 * word: 819 */ 820 stat.aue_rxstat &= AUE_RXSTAT_MASK; 821 if (stat.aue_rxstat) { 822 if_inc_counter(ifp, IFCOUNTER_IERRORS, 1); 823 goto tr_setup; 824 } 825 /* No errors; receive the packet. */ 826 actlen -= (sizeof(stat) + ETHER_CRC_LEN); 827 } 828 uether_rxbuf(ue, pc, 0, actlen); 829 830 /* FALLTHROUGH */ 831 case USB_ST_SETUP: 832 tr_setup: 833 usbd_xfer_set_frame_len(xfer, 0, usbd_xfer_max_len(xfer)); 834 usbd_transfer_submit(xfer); 835 uether_rxflush(ue); 836 return; 837 838 default: /* Error */ 839 DPRINTF("bulk read error, %s\n", 840 usbd_errstr(error)); 841 842 if (error != USB_ERR_CANCELLED) { 843 /* try to clear stall first */ 844 usbd_xfer_set_stall(xfer); 845 goto tr_setup; 846 } 847 return; 848 } 849 } 850 851 static void 852 aue_bulk_write_callback(struct usb_xfer *xfer, usb_error_t error) 853 { 854 struct aue_softc *sc = usbd_xfer_softc(xfer); 855 struct ifnet *ifp = uether_getifp(&sc->sc_ue); 856 struct usb_page_cache *pc; 857 struct mbuf *m; 858 uint8_t buf[2]; 859 int actlen; 860 861 usbd_xfer_status(xfer, &actlen, NULL, NULL, NULL); 862 pc = usbd_xfer_get_frame(xfer, 0); 863 864 switch (USB_GET_STATE(xfer)) { 865 case USB_ST_TRANSFERRED: 866 DPRINTFN(11, "transfer of %d bytes complete\n", actlen); 867 if_inc_counter(ifp, IFCOUNTER_OPACKETS, 1); 868 869 /* FALLTHROUGH */ 870 case USB_ST_SETUP: 871 tr_setup: 872 if ((sc->sc_flags & AUE_FLAG_LINK) == 0) { 873 /* 874 * don't send anything if there is no link ! 875 */ 876 return; 877 } 878 IFQ_DRV_DEQUEUE(&ifp->if_snd, m); 879 880 if (m == NULL) 881 return; 882 if (m->m_pkthdr.len > MCLBYTES) 883 m->m_pkthdr.len = MCLBYTES; 884 if (sc->sc_flags & AUE_FLAG_VER_2) { 885 886 usbd_xfer_set_frame_len(xfer, 0, m->m_pkthdr.len); 887 888 usbd_m_copy_in(pc, 0, m, 0, m->m_pkthdr.len); 889 890 } else { 891 892 usbd_xfer_set_frame_len(xfer, 0, (m->m_pkthdr.len + 2)); 893 894 /* 895 * The ADMtek documentation says that the 896 * packet length is supposed to be specified 897 * in the first two bytes of the transfer, 898 * however it actually seems to ignore this 899 * info and base the frame size on the bulk 900 * transfer length. 901 */ 902 buf[0] = (uint8_t)(m->m_pkthdr.len); 903 buf[1] = (uint8_t)(m->m_pkthdr.len >> 8); 904 905 usbd_copy_in(pc, 0, buf, 2); 906 usbd_m_copy_in(pc, 2, m, 0, m->m_pkthdr.len); 907 } 908 909 /* 910 * if there's a BPF listener, bounce a copy 911 * of this frame to him: 912 */ 913 BPF_MTAP(ifp, m); 914 915 m_freem(m); 916 917 usbd_transfer_submit(xfer); 918 return; 919 920 default: /* Error */ 921 DPRINTFN(11, "transfer error, %s\n", 922 usbd_errstr(error)); 923 924 if_inc_counter(ifp, IFCOUNTER_OERRORS, 1); 925 926 if (error != USB_ERR_CANCELLED) { 927 /* try to clear stall first */ 928 usbd_xfer_set_stall(xfer); 929 goto tr_setup; 930 } 931 return; 932 } 933 } 934 935 static void 936 aue_tick(struct usb_ether *ue) 937 { 938 struct aue_softc *sc = uether_getsc(ue); 939 struct mii_data *mii = GET_MII(sc); 940 941 AUE_LOCK_ASSERT(sc, MA_OWNED); 942 943 mii_tick(mii); 944 if ((sc->sc_flags & AUE_FLAG_LINK) == 0 945 && mii->mii_media_status & IFM_ACTIVE && 946 IFM_SUBTYPE(mii->mii_media_active) != IFM_NONE) { 947 sc->sc_flags |= AUE_FLAG_LINK; 948 aue_start(ue); 949 } 950 } 951 952 static void 953 aue_start(struct usb_ether *ue) 954 { 955 struct aue_softc *sc = uether_getsc(ue); 956 957 /* 958 * start the USB transfers, if not already started: 959 */ 960 usbd_transfer_start(sc->sc_xfer[AUE_INTR_DT_RD]); 961 usbd_transfer_start(sc->sc_xfer[AUE_BULK_DT_RD]); 962 usbd_transfer_start(sc->sc_xfer[AUE_BULK_DT_WR]); 963 } 964 965 static void 966 aue_init(struct usb_ether *ue) 967 { 968 struct aue_softc *sc = uether_getsc(ue); 969 struct ifnet *ifp = uether_getifp(ue); 970 int i; 971 972 AUE_LOCK_ASSERT(sc, MA_OWNED); 973 974 /* 975 * Cancel pending I/O 976 */ 977 aue_reset(sc); 978 979 /* Set MAC address */ 980 for (i = 0; i != ETHER_ADDR_LEN; i++) 981 aue_csr_write_1(sc, AUE_PAR0 + i, IF_LLADDR(ifp)[i]); 982 983 /* update promiscuous setting */ 984 aue_setpromisc(ue); 985 986 /* Load the multicast filter. */ 987 aue_setmulti(ue); 988 989 /* Enable RX and TX */ 990 aue_csr_write_1(sc, AUE_CTL0, AUE_CTL0_RXSTAT_APPEND | AUE_CTL0_RX_ENB); 991 AUE_SETBIT(sc, AUE_CTL0, AUE_CTL0_TX_ENB); 992 AUE_SETBIT(sc, AUE_CTL2, AUE_CTL2_EP3_CLR); 993 994 usbd_xfer_set_stall(sc->sc_xfer[AUE_BULK_DT_WR]); 995 996 ifp->if_drv_flags |= IFF_DRV_RUNNING; 997 aue_start(ue); 998 } 999 1000 static void 1001 aue_setpromisc(struct usb_ether *ue) 1002 { 1003 struct aue_softc *sc = uether_getsc(ue); 1004 struct ifnet *ifp = uether_getifp(ue); 1005 1006 AUE_LOCK_ASSERT(sc, MA_OWNED); 1007 1008 /* if we want promiscuous mode, set the allframes bit: */ 1009 if (ifp->if_flags & IFF_PROMISC) 1010 AUE_SETBIT(sc, AUE_CTL2, AUE_CTL2_RX_PROMISC); 1011 else 1012 AUE_CLRBIT(sc, AUE_CTL2, AUE_CTL2_RX_PROMISC); 1013 } 1014 1015 /* 1016 * Set media options. 1017 */ 1018 static int 1019 aue_ifmedia_upd(struct ifnet *ifp) 1020 { 1021 struct aue_softc *sc = ifp->if_softc; 1022 struct mii_data *mii = GET_MII(sc); 1023 struct mii_softc *miisc; 1024 int error; 1025 1026 AUE_LOCK_ASSERT(sc, MA_OWNED); 1027 1028 sc->sc_flags &= ~AUE_FLAG_LINK; 1029 LIST_FOREACH(miisc, &mii->mii_phys, mii_list) 1030 PHY_RESET(miisc); 1031 error = mii_mediachg(mii); 1032 return (error); 1033 } 1034 1035 /* 1036 * Report current media status. 1037 */ 1038 static void 1039 aue_ifmedia_sts(struct ifnet *ifp, struct ifmediareq *ifmr) 1040 { 1041 struct aue_softc *sc = ifp->if_softc; 1042 struct mii_data *mii = GET_MII(sc); 1043 1044 AUE_LOCK(sc); 1045 mii_pollstat(mii); 1046 ifmr->ifm_active = mii->mii_media_active; 1047 ifmr->ifm_status = mii->mii_media_status; 1048 AUE_UNLOCK(sc); 1049 } 1050 1051 /* 1052 * Stop the adapter and free any mbufs allocated to the 1053 * RX and TX lists. 1054 */ 1055 static void 1056 aue_stop(struct usb_ether *ue) 1057 { 1058 struct aue_softc *sc = uether_getsc(ue); 1059 struct ifnet *ifp = uether_getifp(ue); 1060 1061 AUE_LOCK_ASSERT(sc, MA_OWNED); 1062 1063 ifp->if_drv_flags &= ~IFF_DRV_RUNNING; 1064 sc->sc_flags &= ~AUE_FLAG_LINK; 1065 1066 /* 1067 * stop all the transfers, if not already stopped: 1068 */ 1069 usbd_transfer_stop(sc->sc_xfer[AUE_BULK_DT_WR]); 1070 usbd_transfer_stop(sc->sc_xfer[AUE_BULK_DT_RD]); 1071 usbd_transfer_stop(sc->sc_xfer[AUE_INTR_DT_RD]); 1072 1073 aue_csr_write_1(sc, AUE_CTL0, 0); 1074 aue_csr_write_1(sc, AUE_CTL1, 0); 1075 aue_reset(sc); 1076 } 1077