xref: /freebsd/sys/dev/uart/uart_dev_msm.h (revision 95ee2897e98f5d444f26ed2334cc7c439f9c16c6)

/*-
 * Copyright (c) 2014 Ganbold Tsagaankhuu <ganbold@freebsd.org>
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 *
 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
 * ARE DISCLAIMED.  IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
 * SUCH DAMAGE.
 */

#ifndef	_UART_DM_H_
#define	_UART_DM_H_

#define	UART_DM_EXTR_BITS(value, start_pos, end_pos) \
	    ((value << (32 - end_pos)) >> (32 - (end_pos - start_pos)))

/* UART Parity Mode */
enum UART_DM_PARITY_MODE {
	UART_DM_NO_PARITY,
	UART_DM_ODD_PARITY,
	UART_DM_EVEN_PARITY,
	UART_DM_SPACE_PARITY
};

/* UART Stop Bit Length */
enum UART_DM_STOP_BIT_LEN {
	UART_DM_SBL_9_16,
	UART_DM_SBL_1,
	UART_DM_SBL_1_9_16,
	UART_DM_SBL_2
};

/* UART Bits per Char */
enum UART_DM_BITS_PER_CHAR {
	UART_DM_5_BPS,
	UART_DM_6_BPS,
	UART_DM_7_BPS,
	UART_DM_8_BPS
};

/* 8-N-1 Configuration */
#define	UART_DM_8_N_1_MODE			(UART_DM_NO_PARITY | \
						(UART_DM_SBL_1 << 2) | \
						(UART_DM_8_BPS << 4))

/* UART_DM Registers */

/* UART Operational Mode Registers (HSUART) */
#define	UART_DM_MR1				0x00
#define	 UART_DM_MR1_AUTO_RFR_LEVEL1_BMSK	0xffffff00
#define	 UART_DM_MR1_AUTO_RFR_LEVEL0_BMSK	0x3f
#define	 UART_DM_MR1_CTS_CTL_BMSK		0x40
#define	 UART_DM_MR1_RX_RDY_CTL_BMSK		0x80

#define	UART_DM_MR2				0x04
#define	 UART_DM_MR2_ERROR_MODE_BMSK		0x40
#define	 UART_DM_MR2_BITS_PER_CHAR_BMSK		0x30
#define	 UART_DM_MR2_STOP_BIT_LEN_BMSK		0x0c
#define	 UART_DM_MR2_PARITY_MODE_BMSK		0x03
#define	 UART_DM_RXBRK_ZERO_CHAR_OFF		(1 << 8)
#define	 UART_DM_LOOPBACK			(1 << 7)

/* UART Clock Selection Register, write only */
#define	UART_DM_CSR				0x08

/* UART DM TX FIFO Registers - 4, write only */
#define	UART_DM_TF(x)				(0x70 + (4 * (x)))

/* UART Command Register, write only */
#define	UART_DM_CR				0x10
#define	 UART_DM_CR_RX_ENABLE			(1 << 0)
#define	 UART_DM_CR_RX_DISABLE			(1 << 1)
#define	 UART_DM_CR_TX_ENABLE			(1 << 2)
#define	 UART_DM_CR_TX_DISABLE			(1 << 3)

/* UART_DM_CR channel command bit value (register field is bits 8:4) */
#define	UART_DM_RESET_RX			0x10
#define	UART_DM_RESET_TX			0x20
#define	UART_DM_RESET_ERROR_STATUS		0x30
#define	UART_DM_RESET_BREAK_INT			0x40
#define	UART_DM_START_BREAK			0x50
#define	UART_DM_STOP_BREAK			0x60
#define	UART_DM_RESET_CTS			0x70
#define	UART_DM_RESET_STALE_INT			0x80
#define	UART_DM_RFR_LOW				0xD0
#define	UART_DM_RFR_HIGH			0xE0
#define	UART_DM_CR_PROTECTION_EN		0x100
#define	UART_DM_STALE_EVENT_ENABLE		0x500
#define	UART_DM_STALE_EVENT_DISABLE		0x600
#define	UART_DM_FORCE_STALE_EVENT		0x400
#define	UART_DM_CLEAR_TX_READY			0x300
#define	UART_DM_RESET_TX_ERROR			0x800
#define	UART_DM_RESET_TX_DONE			0x810

/* UART Interrupt Mask Register */
#define	UART_DM_IMR				0x14
/* these can be used for both ISR and IMR registers */
#define	UART_DM_TXLEV				(1 << 0)
#define	UART_DM_RXHUNT				(1 << 1)
#define	UART_DM_RXBRK_CHNG			(1 << 2)
#define	UART_DM_RXSTALE				(1 << 3)
#define	UART_DM_RXLEV				(1 << 4)
#define	UART_DM_DELTA_CTS			(1 << 5)
#define	UART_DM_CURRENT_CTS			(1 << 6)
#define	UART_DM_TX_READY			(1 << 7)
#define	UART_DM_TX_ERROR			(1 << 8)
#define	UART_DM_TX_DONE				(1 << 9)
#define	UART_DM_RXBREAK_START			(1 << 10)
#define	UART_DM_RXBREAK_END			(1 << 11)
#define	UART_DM_PAR_FRAME_ERR_IRQ		(1 << 12)

#define	UART_DM_IMR_ENABLED			(UART_DM_TX_READY | \
						UART_DM_TXLEV | \
						UART_DM_RXLEV | \
						UART_DM_RXSTALE)

/* UART Interrupt Programming Register */
#define	UART_DM_IPR				0x18
#define	UART_DM_STALE_TIMEOUT_LSB		0x0f
#define	UART_DM_STALE_TIMEOUT_MSB		0x00
#define	UART_DM_IPR_STALE_TIMEOUT_MSB_BMSK	0xffffff80
#define	UART_DM_IPR_STALE_LSB_BMSK		0x1f

/* UART Transmit/Receive FIFO Watermark Register */
#define	UART_DM_TFWR				0x1c
/* Interrupt is generated when FIFO level is less than or equal to this value */
#define	UART_DM_TFW_VALUE			0

#define	UART_DM_RFWR				0x20
/* Interrupt generated when no of words in RX FIFO is greater than this value */
#define	UART_DM_RFW_VALUE			0

/* UART Hunt Character Register */
#define	UART_DM_HCR				0x24

/* Used for RX transfer initialization */
#define	UART_DM_DMRX				0x34
/* Default DMRX value - any value bigger than FIFO size would be fine */
#define	UART_DM_DMRX_DEF_VALUE			0x220

/* Register to enable IRDA function */
#define	UART_DM_IRDA				0x38

/* UART Data Mover Enable Register */
#define	UART_DM_DMEN				0x3c
/*
 * Single-Character mode for RX channel (every character received
 * is zero-padded into a word).
 */
#define	 UART_DM_DMEN_RX_SC_ENABLE		(1 << 5)

/* Number of characters for Transmission */
#define	UART_DM_NO_CHARS_FOR_TX			0x40

/* UART RX FIFO Base Address */
#define	UART_DM_BADR				0x44

#define	UART_DM_SIM_CFG_ADDR			0x80

/* Read only registers */
/* UART Status Register */
#define	UART_DM_SR				0x08
/* register field mask mapping */
#define	 UART_DM_SR_RXRDY			(1 << 0)
#define	 UART_DM_SR_RXFULL			(1 << 1)
#define	 UART_DM_SR_TXRDY			(1 << 2)
#define	 UART_DM_SR_TXEMT			(1 << 3)
#define	 UART_DM_SR_UART_OVERRUN		(1 << 4)
#define	 UART_DM_SR_PAR_FRAME_ERR		(1 << 5)
#define	 UART_DM_RX_BREAK			(1 << 6)
#define	 UART_DM_HUNT_CHAR			(1 << 7)
#define	 UART_DM_RX_BRK_START_LAST		(1 << 8)

/* UART Receive FIFO Registers - 4 in numbers */
#define	UART_DM_RF(x)				(0x70 + (4 * (x)))

/* UART Masked Interrupt Status Register */
#define	UART_DM_MISR				0x10

/* UART Interrupt Status Register */
#define	UART_DM_ISR				0x14

/* Number of characters received since the end of last RX transfer */
#define	UART_DM_RX_TOTAL_SNAP			0x38

/* UART TX FIFO Status Register */
#define	UART_DM_TXFS				0x4c
#define	 UART_DM_TXFS_STATE_LSB(x)		UART_DM_EXTR_BITS(x,0,6)
#define	 UART_DM_TXFS_STATE_MSB(x)		UART_DM_EXTR_BITS(x,14,31)
#define	 UART_DM_TXFS_BUF_STATE(x)		UART_DM_EXTR_BITS(x,7,9)
#define	 UART_DM_TXFS_ASYNC_STATE(x)		UART_DM_EXTR_BITS(x,10,13)

/* UART RX FIFO Status Register */
#define	UART_DM_RXFS				0x50
#define	 UART_DM_RXFS_STATE_LSB(x)		UART_DM_EXTR_BITS(x,0,6)
#define	 UART_DM_RXFS_STATE_MSB(x)		UART_DM_EXTR_BITS(x,14,31)
#define	 UART_DM_RXFS_BUF_STATE(x)		UART_DM_EXTR_BITS(x,7,9)
#define	 UART_DM_RXFS_ASYNC_STATE(x)		UART_DM_EXTR_BITS(x,10,13)

#endif	/* _UART_DM_H_ */